NUMBER TYPE PRODUCT SPECIFICATION GS-12-1195 TITLE PAGE REVISION 1 of 7 C AUTHORIZED BY M.2 connector DATE Kenny Tai 2014/11/19 CLASSIFICATION UNRESTRICTED 1. SCOPE 1.1. Contents This Product Specification covers the 0.5mm pitch M.2 connector series, with selective gold and Ni plating. 1.2. Qualification When tests are performed on the subject product line, the procedures specified specifications shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 2. Applicable Document FCI DRAWING: REFER TO EACH DRAWING INDIVIDUALLY Drawing number Product height(mm) Key ID Note 10128786 3.2mm A - 10128787 3.2mm B - 10128788 3.2mm E - 10128792 4.0mm A - 10128793 4.0mm B - 10128794 4.0mm E - 10128796 8.5mm B - 10128797 8.5mm E - 10128798 5.5mm M - 10131758 8.5mm M - Copyright FCI. Form E-3701 - Revision C GS-01-029 PDS: Rev :C STATUS:Released Printed: Jan 16, 2015 NUMBER TYPE PRODUCT SPECIFICATION GS-12-1195 TITLE PAGE REVISION 2 of 7 M.2 connector AUTHORIZED BY Kenny Tai C DATE 2014/11/19 CLASSIFICATION UNRESTRICTED 3. Requirements 3.1 DESIGN AND CONSTRUCTION Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. 3.2 MATERIALS 1.HousingThermoplastic 2.ContactCopper alloy 3.NailCopper alloy 3.3 RATINGs Current: 0.5A Voltage: 50V AC Temperature: - 40 C to +80 C 3.4 Performance Requirements and Test description The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Figure 1. All tests shall be performed at ambient environmental conditions. Copyright FCI. Form E-3701 - Revision C GS-01-029 PDS: Rev :C STATUS:Released Printed: Jan 16, 2015 NUMBER TYPE GS-12-1195 PRODUCT SPECIFICATION TITLE PAGE REVISION 3 of 7 M.2 connector AUTHORIZED BY C DATE Kenny Tai 2014/11/19 CLASSIFICATION UNRESTRICTED 3.5 Test Requirements and Procedures Summary Test Item ITEM 1 (Frequency) Examination of Product Requirements Meets requirements of product drawing. No physical damage. Procedure Visual inspection in compliance with appliance specification and document are performed, the test samples shall be free from defects such as damage, creep, deformation, blister and burrs that are detrimental to the function and appearance of test samples. (EIA-364-18) A.Electrical Requirement Test Item ITEM 2 (Frequency) Low Level Contact Resistance Requirements 55m MAX.per contact (Initial) R=20m Max.(Final) 3 Dielectric withstanding No breakdown Voltage 4 Insulation resistance 5 Contact current rating. 0.5 amperes min. [ 500 ] M Ohm Min.( Mated) [ 100 ] M Ohm Min.(UnMated) Procedure Terminal: measure by dry circuit, 20mV Max, 10mA. EIA-364-06 Shell: measure by open circuit, 5V Max, 100mA. (EIA-364-23) 1. Unmated connector, apply [300V] AC (rms) for 1 minute between adjacent terminals or ground. 2. Mated connector, apply [300V] AC (rms) for 1 minute between adjacent terminal or ground. (EIA-364-20) 1. Unmated connector, apply 500V DC between adjacent terminals or ground. 2. Mated connector, apply 150V DC between adjacent terminals or ground. (EIA-364-21) ambient temperature;25 at still air temperature change.Not exceed 30 (EIA-364-70) Copyright FCI. Form E-3701 - Revision C GS-01-029 PDS: Rev :C STATUS:Released Printed: Jan 16, 2015 NUMBER TYPE GS-12-1195 PRODUCT SPECIFICATION TITLE PAGE REVISION 4 of 7 M.2 connector AUTHORIZED BY C DATE Kenny Tai 2014/11/19 CLASSIFICATION UNRESTRICTED B Mechanical Requirement Test Item ITEM (Frequency) Requirements 6 Mating Force 2.04Kgf(20N) Max 7 Unmating Force 0.1Kgf(0.98N) Min 8 Durability No evidence of physical damage. 9 Durability (Preconditioning) 10 Vibration Appearance: no damage. Discontinuity: 1 microsecond Max. 11 Mechanical Shock Appearance: no damage. Discontinuity: 1 microsecond Max. 12 Reseating No evidence of physical damage No evidence of physical damage. Procedure Operation Speed[ 100 ] mm/min. Measure the force required to mate connector. (EIA-364-13) Operation Speed[ 100 ] mm/min. Measure the force required to unmate connector. (EIA-364-13) Operation Speed[ 100+/-50 ] cycle per hour. Durability Cycles60 cycles for 15u" & 30u" Au plating; 25 cycles for gold flash and other Au thickness. (EIA-364-09) Perform 5 unplug/plug cycles if the application requires up to 25 over the life of the connector or socket; 20 cycles if the application requires 26-200; or 50 cycles if the application requires 201 or greater. (EIA-364-09) Test condition VII test condition letter D(15 Minutes in each of 3 mutually perpendicular Direction both mating halves,should be rigidly fixed so as not to contribute to the relative motion of one contact against another .the method of fixturing should be detailed in the test report .(EIA-364-28) Pulse width2msec Wave formhalf sine 2450m/s2 {250G} 3 strokes in X, Y and Z axes by 2 direction (EIA-364-27 ) Manually unplug/plug the connector or socket, perform 3 such cycles. Copyright FCI. Form E-3701 - Revision C GS-01-029 PDS: Rev :C STATUS:Released Printed: Jan 16, 2015 NUMBER TYPE PRODUCT SPECIFICATION GS-12-1195 TITLE PAGE REVISION 5 of 7 M.2 connector AUTHORIZED BY C DATE Kenny Tai 2014/11/19 CLASSIFICATION UNRESTRICTED C Environmental Requirement ITEM Test Item Requirements Procedure Pre Heat150~180, 9030sec. Heat230 Min., 3010sec. Peak Temp.260+0/-5, 10sec. Duration3 cycles Mated Connectors -55+/-3 (30 min.), +85+/-2 (30 min.) Perform this cycle, repeat 5 cycles (EIA-364-32) Mated connectors Cycle the connector between -15+/-3 and 85+/-3. Ramps should be 1 min. per minute, and dwell times should ensure the contacts reach the temperature extremes (5 minutes min.). Humidity is not controlled. Perform 10 such cycles. Cycle the connector between -15+/-3 and 85+/-3. Ramps should be 1 min. per minute, and dwell times should ensure the contacts reach the temperature extremes (5 minutes min.). Humidity is not controlled. Perform 500 such cycles. Subject mated Connectors to 96 hours at 40 with 90~95% RH. (EIA-364-31 Method II Test Condition A.) 13 Resistance to Reflow Soldering Heat No physical damage shall occur. Lead-Free (See Note 2) 14 Thermal shock See Note 1 15 Thermal Disturbance See Note 1 16 Thermal Cycling See Note 1 17 Humidity See Note 1 18 Temperature Life See Note 1 Mated Connector 90, 288 hours, (EIA-364-17 Method A.) Salt Spray No detrimental corrosion allowed in contact area and base metal exposed. Subject mated connectors to 35+/-2 and 5+/-1% salt condition for 24hours. After test, rinse the sample with water and recondition the room temperature for 1 hour. (EIA-364-26B) 19 Note 1Shall meet visual requirements, show no physical damage, and meet requirement of additional tests as specified in the test sequence. Note 2Resistance to soldering process is indicated on notes of customer drawing. Select the appropriate test type which drawing notes are matched with. Copyright FCI. Form E-3701 - Revision C GS-01-029 PDS: Rev :C STATUS:Released Printed: Jan 16, 2015 NUMBER TYPE PRODUCT SPECIFICATION GS-12-1195 TITLE PAGE REVISION 6 of 7 C AUTHORIZED BY M.2 connector DATE Kenny Tai 2014/11/19 CLASSIFICATION UNRESTRICTED 3.6 TEST SEQUENCE Test group Examination of Product Low level Contact resistance Dielectric withstanding Voltage Insulation Resistance Contact current rating Mating Force Unmating Force Durability Durability (Preconditioning) Vibration Mechanical Shock Reseating Resistance to Reflow Soldering Heat Thermal Shock Thermal Disturbance Thermal Cycling Humidity Temperature Life Temperature Life (Precondition) A B C D E F G H I 1,7 1,10 1,3 1,3 1,3 1,8 1,10 1,10 1,10 2,5,7 2,5,7,9 2,5,7,9 2,5,7,9 2,8 3,6, 9 2,5 2 3,6 4,7 5 3 3 3 3 6 8 6 8 8 2 4 6 6 4 4 4 4 Salt Spray 2 NOTENumbers indicate sequence in which tests are performed. Copyright FCI. Form E-3701 - Revision C GS-01-029 PDS: Rev :C STATUS:Released Printed: Jan 16, 2015 NUMBER TYPE GS-12-1195 PRODUCT SPECIFICATION TITLE PAGE REVISION 7 of 7 C AUTHORIZED BY M.2 connector DATE Kenny Tai 2014/11/19 CLASSIFICATION UNRESTRICTED REVISION RECORD Rev Page A B C All ALL ALL Description Initial release Change durabuluty test cycles Removed P/Ns which are not launched and obsoleted EC# Date ELX-T-18734 ELX-T-19481 2014-06-04 2014-09-03 2014-11-19 Copyright FCI. Form E-3701 - Revision C GS-01-029 PDS: Rev :C STATUS:Released Printed: Jan 16, 2015 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: FCI / Amphenol: 10128786-001RLF 10128788-004RLF 10128792-001RLF 10128794-001RLF 10128796-001RLF 10128797001RLF 10128794-004RLF 10128797-004RLF 10128792-004RLF