NUMBER GS-12-1195 TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
M.2 connector 1 of 7 C
AUTHORIZED BY DATE
Kenny Tai 2014/11/19
CLASSIFICATION
UNRESTRICTED
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
1. SCOPE
1.1. Contents
This Product Specification covers the 0.5mm pitch M.2 connector series, with selective gold and Ni plating.
1.2. Qualification
When tests are performed on the subject product line, the procedures specified specifications shall be
used. All inspections shall be performed using the applicable inspection plan and product drawing.
2. Applicable Document
FCI DRAWING: REFER TO EACH DRAWING INDIVIDUALLY
Drawing number Product height(mm) Key ID Note
10128786 3.2mm A -
10128787 3.2mm B -
10128788 3.2mm E -
10128792 4.0mm A -
10128793 4.0mm B -
10128794 4.0mm E -
10128796 8.5mm B -
10128797 8.5mm E -
10128798 5.5mm M -
10131758 8.5mm M -
PDS: Rev :C STATUS:Released Printed: Jan 16, 2015
NUMBER GS-12-1195 TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
M.2 connector 2 of 7 C
AUTHORIZED BY DATE
Kenny Tai 2014/11/19
CLASSIFICATION
UNRESTRICTED
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
3. Requirements
3.1 DESIGN AND CONSTRUCTION
Product shall be of the design, construction and physical dimensions specified on the applicable product
drawing.
3.2 MATERIALS
1.HousingThermoplastic
2.ContactCopper alloy
3.NailCopper alloy
3.3 RATINGs
Current: 0.5A
Voltage: 50V AC
Temperature: - 40 °C to +80 °C
3.4 Performance Requirements and Test description
The product shall be designed to meet the electrical, mechanical and environmental performance
requirements specified in Figure 1. All tests shall be performed at ambient environmental conditions.
PDS: Rev :C STATUS:Released Printed: Jan 16, 2015
NUMBER GS-12-1195 TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
M.2 connector 3 of 7 C
AUTHORIZED BY DATE
Kenny Tai 2014/11/19
CLASSIFICATION
UNRESTRICTED
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
3.5 Test Requirements and Procedures Summary
ITEM Test Item
(Frequency) Requirements Procedure
1 Examination of
Product
Meets requirements of product
drawing. No physical damage.
Visual inspection in compliance with
appliance specification and document are
performed, the test samples shall be free from
defects such as damage, creep, deformation,
blister and burrs that are detrimental to the
function and appearance of test samples.
(EIA-364-18)
A.Electrical Requirement
ITEM Test Item
(Frequency) Requirements Procedure
2
Low Level
Contact Resistance
 55m MAX.per contact (Initial)
󳮀󳻞
R=20m Max.(Final)
Terminal: measure by dry circuit, 20mV Max,
10mA.
EIA-364-06 Shell: measure by open circuit,
5V Max, 100mA.
(EIA-364-23)
3 Dielectric withstanding
Voltage No breakdown
1. Unmated connector, apply [300V] AC
(rms) for 1 minute between adjacent
terminals or ground.
2. Mated connector, apply [300V] AC (rms)
for 1 minute between adjacent terminal or
ground.
(EIA-364-20)
4 Insulation resistance [ 500 ] M Ohm Min.( Mated)
[ 100 ] M Ohm Min.(UnMated)
1. Unmated connector, apply 500V DC
between adjacent terminals or ground.
2. Mated connector, apply 150V DC
between
adjacent terminals or ground.
(EIA-364-21)
5 Contact current rating. 0.5 amperes min.
ambient temperature;25at still air
temperature change.Not exceed 30
(EIA-364-70)
PDS: Rev :C STATUS:Released Printed: Jan 16, 2015
NUMBER GS-12-1195 TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
M.2 connector 4 of 7 C
AUTHORIZED BY DATE
Kenny Tai 2014/11/19
CLASSIFICATION
UNRESTRICTED
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
B Mechanical Requirement
ITEM Test Item
(Frequency) Requirements Procedure
6 Mating Force 2.04Kgf(20N) Max
Operation Speed[ 100 ] mm/min.
Measure the force required to mate
connector.
(EIA-364-13)
7 Unmating Force 0.1Kgf(0.98N) Min
Operation Speed[ 100 ] mm/min.
Measure the force required to unmate
connector.
(EIA-364-13)
8 Durability No evidence of physical damage.
Operation Speed[ 100+/-50 ] cycle per
hour.
Durability Cycles60 cycles for 15u” & 30u” Au
plating; 25 cycles for gold flash and other Au
thickness.
(EIA-364-09)
9 Durability
(Preconditioning) No evidence of physical damage
Perform 5 unplug/plug cycles if the
application requires up to 25 over the life of
the connector or socket; 20 cycles if the
application requires 26-200; or 50 cycles if
the application requires 201 or greater.
(EIA-364-09)
10 Vibration Appearance: no damage.
Discontinuity: 1 microsecond Max.
Test condition VII test condition letter D(15
Minutes in each of 3 mutually perpendicular
Direction both mating halves,should be
rigidly fixed so as not to contribute to the
relative motion of one contact against
another .the method of fixturing should be
d
etailed in the test report .(EI
A
-364-28)
11 Mechanical Shock Appearance: no damage.
Discontinuity: 1 microsecond Max.
Pulse width2msec
Wave formhalf sine 2450m/s2 {250G}
3 strokes in X, Y and Z axes by 2 direction
(
EI
A
-364-27 )
12 Reseating No evidence of physical damage. Manually unplug/plug the connector or
socket, perform 3 such cycles.
PDS: Rev :C STATUS:Released Printed: Jan 16, 2015
NUMBER GS-12-1195 TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
M.2 connector 5 of 7 C
AUTHORIZED BY DATE
Kenny Tai 2014/11/19
CLASSIFICATION
UNRESTRICTED
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
C Environmental Requirement
ITEM Test Item Requirements Procedure
13 Resistance to Reflow
Soldering Heat
No physical damage shall occur.
Lead-Free
(See Note 2)
Pre Heat150~180, 90±30sec.
Heat230Min., 30±10sec.
Peak Temp.260+0/-5, 10sec.
Duration3 cycles
14 Thermal shock See Note 1
Mated Connectors
-55+/-3(30 min.), +85+/-2(30 min.)
Perform this cycle, repeat 5 cycles
(EIA-364-32)
15 Thermal Disturbance See Note 1
Mated connectors
Cycle the connector between -15+/-3
and 85+/-3. Ramps should be 1min.
per minute, and dwell times should ensure
the contacts reach the temperature
extremes (5 minutes min.). Humidity is not
controlled. Perform 10 such cycles.
16 Thermal Cycling See Note 1
Cycle the connector between -15+/-3
and 85+/-3. Ramps should be 1min.
per minute, and dwell times should ensure
the contacts reach the temperature
extremes (5 minutes min.). Humidity is not
controlled. Perform 500 such cycles.
17 Humidity See Note 1
Subject mated Connectors to 96 hours at
40with 90~95% RH.
(EIA-364-31 Method II Test Condition A.)
18 Temperature Life See Note 1 Mated Connector 90, 288 hours,
(EIA-364-17 Method A.)
19 Salt Spray
No detrimental corrosion allowed
in contact area and base metal
exposed.
Subject mated connectors to 35+/-2 and
5+/-1% salt condition for 24hours. After
test, rinse the sample with water and
recondition the room temperature for 1
hour. (EIA-364-26B)
Note 1Shall meet visual requirements, show no physical damage, and meet requirement of additional tests as
specified in the test sequence.
Note 2Resistance to soldering process is indicated on notes of customer drawing. Select the appropriate test
type which drawing notes are matched with.
PDS: Rev :C STATUS:Released Printed: Jan 16, 2015
NUMBER GS-12-1195 TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
M.2 connector 6 of 7 C
AUTHORIZED BY DATE
Kenny Tai 2014/11/19
CLASSIFICATION
UNRESTRICTED
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NOTENumbers indicate sequence in which tests are performed.
3.6 TEST SEQUENCE
Test group A B C D E F G H I
Examination of Product 1,8 1,10 1,10 1,10 1,7 1,10 1,3 1,3 1,3
Low level Contact resistance 2,5,7 2,5,7,9 2,5,7,9 2,5,7,9 2,8
Dielectric withstanding Voltage 3,6, 9
Insulation Resistance 2,5
Contact current rating 2
Mating Force 3,6
Unmating Force 4,7
Durability 5
Durability (Preconditioning) 3 3 3 3
Vibration 6
Mechanical Shock 8
Reseating 6 8 8
Resistance to Reflow Soldering
Heat 2
Thermal Shock 4
Thermal Disturbance
Thermal Cycling 6
Humidity 6 4
Temperature Life 4
Temperature Life (Precondition) 4 4
Salt Spray 2
PDS: Rev :C STATUS:Released Printed: Jan 16, 2015
NUMBER GS-12-1195 TYPE
PRODUCT SPECIFICATION
TITLE PAGE REVISION
M.2 connector 7 of 7 C
AUTHORIZED BY DATE
Kenny Tai 2014/11/19
CLASSIFICATION
UNRESTRICTED
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
REVISION RECORD
Rev Page Description EC# Date
A All Initial release - 2014-06-04
B ALL Change durabuluty test cycles ELX-T-18734 2014-09-03
C ALL Removed P/Ns which are not launched and obsoleted ELX-T-19481 2014-11-19
PDS: Rev :C STATUS:Released Printed: Jan 16, 2015
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
FCI / Amphenol:
10128786-001RLF 10128788-004RLF 10128792-001RLF 10128794-001RLF 10128796-001RLF 10128797-
001RLF 10128794-004RLF 10128797-004RLF 10128792-004RLF