© Semiconductor Components Industries, LLC, 2006
October, 2006 Rev. 7
1Publication Order Number:
MC74AC04/D
MC74AC04, MC74ACT04
Hex Inverter
Features
Outputs Source/Sink 24 mA
ACT04 Has TTL Compatible Inputs
PbFree Packages are Available
1314 12 11 10 9 8
21 34567
GND
VCC
Figure 1. Pinout: 14Lead Packages Conductors
(Top View)
MAXIMUM RATINGS
Rating Symbol Value Unit
DC Supply Voltage (Referenced to GND) VCC 0.5 to
+7.0
V
DC Input Voltage (Referenced to GND) Vin 0.5 to
VCC +0.5
V
DC Output Voltage (Referenced to GND) Vout 0.5 to
VCC +0.5
V
DC Input Current, per Pin Iin ±20 mA
DC Output Sink/Source Current, per Pin Iout ±50 mA
DC VCC or GND Current per Output Pin ICC ±50 mA
Storage Temperature Tstg 65 to
+150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
TSSOP14
DT SUFFIX
CASE 948G
1
14
SOEIAJ14
M SUFFIX
CASE 965
1
14
SOIC14
D SUFFIX
CASE 751A
1
14
1
14
PDIP14
N SUFFIX
CASE 646
http://onsemi.com
See detailed ordering and shipping information in the package
dimensions section on page 5 of this data sheet.
ORDERING INFORMATION
MC74AC04, MC74ACT04
http://onsemi.com
2
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Typ Max Unit
VCC Supply Voltage
AC 2.0 5.0 6.0
V
ACT 4.5 5.0 5.5
Vin, Vout DC Input Voltage, Output Voltage (Ref. to GND) 0VCC V
tr, tfInput Rise and Fall Time (Note 1)
AC Devices except Schmitt Inputs
VCC @ 3.0 V 150
VCC @ 4.5 V 40 ns/V
VCC @ 5.5 V 25
tr, tfInput Rise and Fall Time (Note 2)
ACT Devices except Schmitt Inputs
VCC @ 4.5 V 10
ns/V
VCC @ 5.5 V 8.0
TJJunction Temperature (PDIP) 140 °C
TAOperating Ambient Temperature Range 40 25 85 °C
IOH Output Current High 24 mA
IOL Output Current Low 24 mA
1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times.
2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times.
DC CHARACTERISTICS
Symbol Parameter VCC
(V)
74AC 74AC
Unit Conditions
TA = +25°C
TA =
40°C to
+85°C
Typ Guaranteed Limits
VIH Minimum High Level
Input Voltage
3.0 1.5 2.1 2.1 VOUT = 0.1 V
4.5 2.25 3.15 3.15 V or VCC 0.1 V
5.5 2.75 3.85 3.85
VIL Maximum Low Level
Input Voltage
3.0 1.5 0.9 0.9 VOUT = 0.1 V
4.5 2.25 1.35 1.35 V or VCC 0.1 V
5.5 2.75 1.65 1.65
VOH Minimum High Level
Output Voltage
3.0 2.99 2.9 2.9 IOUT = 50 mA
4.5 4.49 4.4 4.4 V
5.5 5.49 5.4 5.4
V
*VIN = VIL or VIH
3.0 2.56 2.46 12 mA
4.5 3.86 3.76 IOH 24 mA
5.5 4.86 4.76 24 mA
VOL Maximum Low Level
Output Voltage
3.0 0.002 0.1 0.1 IOUT = 50 mA
4.5 0.001 0.1 0.1 V
5.5 0.001 0.1 0.1
V
*VIN = VIL or VIH
3.0 0.36 0.44 12 mA
4.5 0.36 0.44 IOL 24 mA
5.5 0.36 0.44 24 mA
IIN Maximum Input
Leakage Current 5.5 ±0.1 ±1.0 mAVI = VCC, GND
IOLD †Minimum Dynamic
Output Current
5.5 75 mA VOLD = 1.65 V Max
IOHD 5.5 75 mA VOHD = 3.85 V Min
ICC Maximum Quiescent
Supply Current 5.5 4.0 40 mAVIN = VCC or GND
*All outputs loaded; thresholds on input associated with output under test.
Maximum test duration 2.0 ms, one output loaded at a time.
NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC.
MC74AC04, MC74ACT04
http://onsemi.com
3
AC CHARACTERISTICS (For Figures and Waveforms See Section 3 of the ON Semiconductor FACT Data Book, DL138/D)
Symbol Parameter VCC*
(V)
74AC 74AC
Unit Fig.
No.
TA = +25°C
CL = 50 pF
TA = 40°C
to +85°C
CL = 50 pF
Min Typ Max Min Max
tPLH Propagation Delay 3.3 1.5 4.5 9.0 1.0 10 ns 35
5.0 1.5 4.0 7.0 1.0 7.5
tPHL Propagation Delay 3.3 1.5 4.5 8.5 1.0 9.5 ns 35
5.0 1.5 3.5 6.5 1.0 7.0
*Voltage Range 3.3 V is 3.3 V ±0.3 V.
Voltage Range 5.0 V is 5.0 V ±0.5 V.
DC CHARACTERISTICS
Symbol Parameter VCC
(V)
74ACT 74ACT
Unit Conditions
TA = +25°C
TA =
40°C to
+85°C
Typ Guaranteed Limits
VIH Minimum High Level
Input Voltage
4.5 1.5 2.0 2.0 VVOUT = 0.1 V
5.5 1.5 2.0 2.0 or VCC 0.1 V
VIL Maximum Low Level
Input Voltage
4.5 1.5 0.8 0.8 VVOUT = 0.1 V
5.5 1.5 0.8 0.8 or VCC 0.1 V
VOH Minimum High Level
Output Voltage
4.5 4.49 4.4 4.4 VIOUT = 50 mA
5.5 5.49 5.4 5.4
*VIN = VIL or VIH
4.5 3.86 3.76 V IOH
24 mA
5.5 4.86 4.76 24 mA
VOL Maximum Low Level
Output Voltage
4.5 0.001 0.1 0.1 VIOUT = 50 mA
5.5 0.001 0.1 0.1
*VIN = VIL or VIH
4.5 0.36 0.44 V IOL
24 mA
5.5 0.36 0.44 24 mA
IIN Maximum Input
Leakage Current 5.5 ±0.1 ±1.0 mAVI = VCC, GND
DICCT Additional Max. ICC/Input 5.5 0.6 1.5 mA VI = VCC 2.1 V
IOLD †Minimum Dynamic
Output Current
5.5 75 mA VOLD = 1.65 V Max
IOHD 5.5 75 mA VOHD = 3.85 V Min
ICC Maximum Quiescent
Supply Current 5.5 4.0 40 mAVIN = VCC or GND
*All outputs loaded; thresholds on input associated with output under test.
Maximum test duration 2.0 ms, one output loaded at a time.
MC74AC04, MC74ACT04
http://onsemi.com
4
AC CHARACTERISTICS (For Figures and Waveforms See Section 3 of the ON Semiconductor FACT Data Book, DL138/D)
Symbol Parameter VCC*
(V)
74ACT 74ACT
Unit Fig.
No.
TA = +25°C
CL = 50 pF
TA = 40°C
to +85°C
CL = 50 pF
Min Typ Max Min Max
tPLH Propagation Delay 5.0 1.5 8.5 1.0 9.0 ns 36
tPHL Propagation Delay 5.0 1.5 8.0 1.0 8.5 ns 36
*Voltage Range 5.0 V is 5.0 V ±0.5 V.
CAPACITANCE
Symbol Parameter Value
Typ Unit Test Conditions
CIN Input Capacitance 4.5 pF VCC = 5.0 V
CPD Power Dissipation Capacitance 30 pF VCC = 5.0 V
MC74AC04, MC74ACT04
http://onsemi.com
5
DEVICE ORDERING INFORMATION
Device Package Shipping
MC74AC04N PDIP14
25 Units/Rail
MC74AC04NG PDIP14
(PbFree)
MC74ACT04N PDIP14
MC74ACT04NG PDIP14
(PbFree)
MC74AC04D SOIC14
55 Units/Rail
MC74AC04DG SOIC14
(PbFree)
MC74AC04DR2 SOIC14
2500/Tape & Reel
MC74AC04DR2G SOIC14
(PbFree)
MC74ACT04D SOIC14
55 Units/Rail
MC74ACT04DG SOIC14
(PbFree)
MC74ACT04DR2 SOIC14
2500/Tape & Reel
MC74ACT04DR2G SOIC14
(PbFree)
MC74AC04DT TSSOP14* 96 Units/Rail
MC74AC04DTR2 TSSOP14*
2500/Tape & Reel
MC74AC04DTR2G TSSOP14*
MC74ACT04DT TSSOP14* 96 Units/Rail
MC74ACT04DTR2 TSSOP14*
2500/Tape & Reel
MC74ACT04DTR2G TSSOP14*
MC74AC04MEL SOEIAJ14
2000/Tape & Reel
MC74AC04MELG SOEIAJ14
(PbFree)
MC74ACT04M SOEIAJ14
50 Units/Rail
MC74ACT04MG SOEIAJ14
(PbFree)
MC74ACT04MEL SOEIAJ14
2000/Tape & Reel
MC74ACT04MELG SOEIAJ14
(PbFree)
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently PbFree.
MC74AC04, MC74ACT04
http://onsemi.com
6
MARKING DIAGRAMS
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
G or G= PbFree Package
PDIP14 SOIC14 TSSOP14
MC74AC04N
AWLYYWWG AC
04
ALYWG
G
MC74ACT04N
AWLYYWWG
74AC04
ALYWG
SOEIAJ14
74ACT04
ALYWG
AC04G
AWLYWW
1
14
ACT04G
AWLYWW
1
14
ACT
04
ALYWG
G
1
14
1
14
1
14
1
14
1
14
1
14
(Note: Microdot may be in either location)
MC74AC04, MC74ACT04
http://onsemi.com
7
PACKAGE DIMENSIONS
PDIP14
CASE 64606
ISSUE P
17
14 8
B
ADIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.715 0.770 18.16 19.56
B0.240 0.260 6.10 6.60
C0.145 0.185 3.69 4.69
D0.015 0.021 0.38 0.53
F0.040 0.070 1.02 1.78
G0.100 BSC 2.54 BSC
H0.052 0.095 1.32 2.41
J0.008 0.015 0.20 0.38
K0.115 0.135 2.92 3.43
L
M−−− 10 −−− 10
N0.015 0.039 0.38 1.01
__
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
F
HG D
K
C
SEATING
PLANE
N
T
14 PL
M
0.13 (0.005)
L
M
J
0.290 0.310 7.37 7.87
MC74AC04, MC74ACT04
http://onsemi.com
8
PACKAGE DIMENSIONS
SOIC14
CASE 751A03
ISSUE H
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.127
(0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
A
B
G
P7 PL
14 8
7
1
M
0.25 (0.010) B M
S
B
M
0.25 (0.010) A S
T
T
F
RX 45
SEATING
PLANE D14 PL K
C
J
M
_DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A8.55 8.75 0.337 0.344
B3.80 4.00 0.150 0.157
C1.35 1.75 0.054 0.068
D0.35 0.49 0.014 0.019
F0.40 1.25 0.016 0.049
G1.27 BSC 0.050 BSC
J0.19 0.25 0.008 0.009
K0.10 0.25 0.004 0.009
M0 7 0 7
P5.80 6.20 0.228 0.244
R0.25 0.50 0.010 0.019
__ __
7.04
14X
0.58
14X
1.52
1.27
DIMENSIONS: MILLIMETERS
1
PITCH
SOLDERING FOOTPRINT*
7X
*For additional information on our PbFree strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
MC74AC04, MC74ACT04
http://onsemi.com
9
PACKAGE DIMENSIONS
TSSOP14
CASE 948G01
ISSUE B
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A4.90 5.10 0.193 0.200
B4.30 4.50 0.169 0.177
C−−− 1.20 −−− 0.047
D0.05 0.15 0.002 0.006
F0.50 0.75 0.020 0.030
G0.65 BSC 0.026 BSC
H0.50 0.60 0.020 0.024
J0.09 0.20 0.004 0.008
J1 0.09 0.16 0.004 0.006
K0.19 0.30 0.007 0.012
K1 0.19 0.25 0.007 0.010
L6.40 BSC 0.252 BSC
M0 8 0 8
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE W.
____
S
U0.15 (0.006) T
2X L/2
S
U
M
0.10 (0.004) V S
T
LU
SEATING
PLANE
0.10 (0.004)
T
ÇÇÇ
ÇÇÇ
ÇÇÇ
SECTION NN
DETAIL E
JJ1
K
K1
ÉÉÉ
ÉÉÉ
DETAIL E
F
M
W
0.25 (0.010)
8
14
7
1
PIN 1
IDENT.
H
G
A
D
C
B
S
U0.15 (0.006) T
V
14X REFK
N
N
7.06
14X
0.36 14X
1.26
0.65
DIMENSIONS: MILLIMETERS
1
PITCH
SOLDERING FOOTPRINT*
*For additional information on our PbFree strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
MC74AC04, MC74ACT04
http://onsemi.com
10
PACKAGE DIMENSIONS
SOEIAJ14
CASE 96501
ISSUE A
HE
A1
DIM MIN MAX MIN MAX
INCHES
−−− 2.05 −−− 0.081
MILLIMETERS
0.05 0.20 0.002 0.008
0.35 0.50 0.014 0.020
0.10 0.20 0.004 0.008
9.90 10.50 0.390 0.413
5.10 5.45 0.201 0.215
1.27 BSC 0.050 BSC
7.40 8.20 0.291 0.323
0.50 0.85 0.020 0.033
1.10 1.50 0.043 0.059
0
0.70 0.90 0.028 0.035
−−− 1.42 −−− 0.056
A1
HE
Q1
LE
_10 _0
_10 _
LE
Q1
_
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH OR PROTRUSIONS AND ARE MEASURED
AT THE PARTING LINE. MOLD FLASH OR
PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
0.13 (0.005) M0.10 (0.004)
D
Z
E
1
14 8
7
eA
b
VIEW P
c
L
DETAIL P
M
A
b
c
D
E
e
0.50
M
Z
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 8002829855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81357733850
MC74AC04/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 3036752175 or 8003443860 Toll Free USA/Canada
Fax: 3036752176 or 8003443867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative