Available on Tape
and Reel For Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 544-2414
+44 2392-232392
Model 2425B50-50C
Rev. A
rit
Xinger Balun
50Ω to 100Ω Balanced
Description
The 2425B50-50C is a low profile sub-miniature balanced to unbalanced
transformer designed for differential inputs and output locations on next generation
wireless chipsets in an easy to use surface mount package covering 802.11b+g.
The 2425B50-50C is ideal for high volume manufacturing and is higher performance
than traditional ceramic baluns. The 2425B50-50C has an unbalanced port
impedance of 50Ω and a 100Ω balanced port impedance*. This transformation
enables single ended signals to be applied to differential ports on modern integrated
chipsets. The output ports have equal amplitude (-3dB) with 180 degree phase
differential. The 2425B50-50C is available on tape and reel for pick and place high
volume manufacturing.
ELECTRICAL SPECIFICATIONS**
Frequency
Unbalanced
Port
Impedance
Balanced
Port
Impedance*
Return
Loss
Insertion
Loss
GHz Ohms Ohms dB min dB max
2.4 – 2.5 50 100 17 0.55***
Amplitude
Balance
Phase
Balance
Power
Handling
ΘJC
Operating
Temp.
dB Degrees max Watts ºC / Watt ºC
Features:
• 2.4 – 2.5 GHz
• 180° Transformer
• 50 Ohm to 2 x 50 Ohm
• 802.11 b+g Compliant
• Low Insertion Loss
• Medium Power
• No DC Decoupling Capacitors
Required
• Input to Output DC Isolation
• Surface Mountable
• Tape & Reel
• Convenient Package
0 ± 0.5 180 ± 5.0 4 28 -55 to +85
**Specification based on performance of unit properly installed on microstrip printed circuit
boards with 50 Ω nominal impedance. Specifications subject to change without notice.
* 50Ω reference to ground
*** Insertion Loss stated at room temperature (0.6 dB Max at +85 ºC)
Outline Drawing
Mechanical Outline
Dimensions are in Inches [Millimeters]
Side ViewTop View (Near-side) Bottom View (Far-side)
.024±.002
[0.61±0.05]
.120±.005
[3.05±0.13]
.120±.005
[3.05±0.13]
456
3 1
2
6X .030±.004
[0.76±0.10]
4X .010±.004
[0.25±0.10]
.095±.004
[2.41±0.10]6X .010±.004
[0.23±0.10]
GND
In
GND
Out 2
GND
Out 1
Designation
5
4
2
1
6
3
Pin
Tolerances are Non-Cumulative
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 544-2414
+44 2392-232392
Available on Tape and
Reel For Pick and Place
Manufacturing.
Model 2425B50-50C
Rev. A
Typical Broadband Performance: 2.3 GHz. to 2.7 GHz.
Pin Configuration:
Balun Pin Configruation
Pin 3
Balanced Port
Terminals
Pin 1
λ4
Unbalanced Port
λ4
50 ς
Pin 5
The internal configuration of the Xinger balun is diagramed to
the left; the unbalanced port is DC connected to ground and the
two balanced ports are DC connected and floating. For many
chipset applications there is an opportunity to eliminate two
decoupling capacitors and/or use a single bias point if
applicable. Differential drive is popular in integrated circuit since
it aids stability in the presence of bond wire and pin inductance,
provides some degree of immunity to power supply and ground
noise, and can provide higher output power in the case of some
device limits. The construction of the Xinger balun is bonded
multi-layered stripline made of low loss dielectric material with
plated through vias connecting the internal circuitry to the
external printed circuit board, similar to that of the Xinger
hybrids and directional couplers.
Available on Tape
and Reel For Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 544-2414
+44 2392-232392
Model 2425B50-50C
Rev. A
Typical Performance: 2.35 GHz. to 2.55 GHz.
Mounting Configuration:
Mounting Footprint
Dimensions are in Inches [Millimeters]
6X .030
[0.76]
3X 50 ς
Transmission
Line
.095
[2.41]
6X .022
[0.57]
2X .009
[0.22] Multiple
plated thru holes
to ground
Solder Resist
Footprint Pad (s)
Circuit Pattern
4X .012
[0.30]
In order for Xinger surface mount components to work
optimally, there must be a 50Ω transmission line to the
balanced port and 50Ω transmission lines from the
unbalanced ports. If this condition is not satisfied, amplitude
balance, insertion loss and VSWR may not meet published
specifications.
All of the Xinger components are constructed from ceramic
filled PTFE composites which possess excellent electrical
and mechanical stability having X and Y thermal coefficient
of expansion (CTE) of 17 ppm/oC
An example of the PCB footprint used in the testing of these
parts is shown to the left. in specific designs, the
transmission line widths need to be adjusted to the unique
dielectric coefficients and thicknesses as well as varying
pick and place equipment tolerances.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 544-2414
+44 2392-232392
Available on Tape and
Reel For Pick and Place
Manufacturing.
Model 2425B50-50C
Rev. A
Packaging and Ordering Information
Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order
quantities are 4000 per reel. See Model Numbers below for further ordering information.
.157
[4.00]
.079 [2.01] .157
[4.00]
Ø.059
[Ø1.50]
.069
[1.75]
.138
[3.50]
.063
[1.61]
Ø.039
[Ø0.99]
Dimensions are in inches [mm]
Direction of
Part Feed
(Unloading)
.315
[8.00]
.010
[0.25]
.030
[0.80]
.130
[3.30]
B
ØA ØC
REEL DIMENSIONS (inches [mm])
ØA
B
ØC
0.32 [8.0]
2.0 [50.8]
7.00 [177.8]
4000
QUANTITY/REEL
TABLE 1
ØD
0.512 [13.0]
ØD
Available on Tape
and Reel For Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 544-2414
+44 2392-232392
Model 2425B50-50C
Rev. A
