ANP AMP* Connector-Specific Kit 768350-1 for AMP-LATCH* 50-Position HDF Connectors Instruction Sheet 408-9834 (was IS 9834} 13MAYS3 RevA PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. AMP hand tools are intended for occasional use and low volume applications. AMP offers a wide selection of powered application equipment for extended-use, production operations. CONNECTOR-~SPECIFIC KIT 768350-1 ADAPTOR TOOL TYPICAL APPLICATIONS MANUAL ARBOR FRAME ASSEMBLY 91085-2 (Ref) AMP-LATCH HAND TOOL KIT 768340-1 BASE ASSEMBLY UNIVERSAL ARBOR TOOL 768338-1 Figure 1 1. INTRODUCTION This instruction sheet covers the description, cable requirements, and installation procedures for AMP Connector-Specific Kit 768350-1, which is used with AMP-LATCH Hand Tool Kit 768340-1 (see instruction AMP Incorporated, Harrisburg, PA 17105 TOOLING ASSISTANCE CENTER 1-800-722-1111 AMP FAX/PRODUCT INFO 1-800-522-6752 This AMP controlled document is subject to change. For tatest revision call the AMP FAX number. Copyright 1992, 1993 by AMP Incorporated. All Intemational Rights Reserved. Trademark cad sheet 408-9828) and Base Assembly Universal Arbor Too! 768338-1 (see 408-9827). The connector- specific kit will terminate AMP-LATCH 50-Position HDF Connectors having 1.27 mm [.050 in.] centerline spacing to ribbon cable (see Figure 2). tof3 Per EC M-3045, EC 0990-0071-93The Base Assembly Universal Arbor Tool is used with AMP Manual Arbor Frame Assembly 91085-2 and AMP Pneumatic Auto-Cycle Unit 91112-3. Refer to 408-7777 and 408-6732, respectively, for tooling information. 2. DESCRIPTION (Figure 1) The connector-specific kit features an upper tool, an adaptor, and a lower insert. The upper tool and the adaptor apply an even force over the length of the connector during termination. The lower insert positions the connector on the tooling assembly. Each component is marked AMP HDF 50. Dimensions on this sheet are in metric units {with U.S. customary equivalents in brackets}. 3. CABLE REQUIREMENTS The connector-specific kit will terminate ribbon cable with 26 AWG solid or stranded conductors, 28 AWG solid or stranded conductors, or 30 AWG solid conductors to all AMP-LATCH 50-position HDF Connectors. Refer to Figure 2 for the recommended cable dimensions. AMP Connector-Specific Kit 768350-1 408-9834 The cable must be cut 90 to the edge of the cable; otherwise an improper termination will result. We suggest you use a guillotine-type cable cutter, such as the Carpenter Mode! 95 which can be purchased from: Carpenter Manufacturing Co., inc. Fairgrounds Drive Manlius, N.Y. 13207 CAUTION "A" +076 [.003] NOTE ACCUMULATIVE TOLERANCE FOR CABLE CONDUCTORS 1 THROUGH 34 1S-+ 254 [010] AND THROUGH 6015 + 38 [.015]. CONDUCTOR DIMENSION SIZE (AWG) TYPE A "BE" i 1.27 mm [.050 IN. 26 Stranded or Solid 0.889mm| "X (Ttal No. of ] 28 Stranded or Solid] [.0351N.} onductors 30 Solid Minus One} Figure 2 ead 9831 AMP-LATCH HAND TOOL KIT 768340-1 (Ref) (Includes AMP-LATCH Hand Tool Subassembly 768942~1 and Base Assembly Universal Hand Tool 768339-1. Refer to 408-9846 and 408-9826) LOCATORS LOWER INSERT SLOT OF FLUTED PLATE Figure 3 ead 4. CONNECTOR-SPECIFIC KIT INSTALLATION (Figures 3 and 4) For hand tool applications, mount the hand tool onto a suitable work surface, whenever possible, before terminating the connectors. Refer to the bench-clamping instructions in 408-9828, packaged with the AMP-LATCH Hand Tool Kit. 1. Slide the upper tool onto the upper tool mount. 2. Slide the lower insert into the slot of the fluted piate. 3. Place the adaptor into the plug connector prior to termination. When using the hand tool, the upper tool is not used. This completes the installation procedure. The adaptor is not needed when terminating receptacle connectors. 20f3 RevaBASE ASSEMBLY UNIVERSAL ARBOR TOOL 768338-1 (Ref) ADAPTOR {Place into Plug Prior to Terminating) LOCATORS UPPER TOOL L AMP Connector-Specific Kit 768350-1 408-9834 For information concerning termination proce- dures, refer to 408-9828 packaged with the AMP-LATCH Hand Tool Kit, and 408-9827 packaged with the Base Assembly Universal Arbor Tool. NOTE 5. CONNECTOR-SPECIFIC KIT INSPECTION Connector-Specific Kit 768350-1 has been inspected and should be verified with the information provided in Figure 5. It is recommended that the connector specitic kit be inspected immediately upon its arrival at your facility (and at regularly scheduled intervals) to ensure that the kit components have not been damaged during handling. For additional information concerning connector- specific kits, or to purchase additional kits, contact your local AMP representative or: SLOT OF FLUTED INSERT CUSTOMER SERVICE (38-35) AMP INCORPORATED P.O. BOX 3608 d Fig. 4 *s HARRISBURG, PA 17105-3608 CONNECTOR-SPECIFIC KIT 768350-1 UPPER TOOL | oO 5.59.22} m! le | [22] 20.83,82 a 89.92 {3.54] ss LOWER INSERT 5.59.22] 15.5[.611] | - 3 [BY EHO Se eo 21.84|.86] el le | _ 100.08 [3.94] ____, ADAPTOR 10.11 [.398] >| 8,15 [.321] "7 SD 1.73 [.068] aol | Le 46.74 [1.840] _y COMPONENT LIST ITEM NO, PART NUMBER DESCRIPTION ary { 549274-6 Upper Tool 1 2 {-43275-1 Lower Insert 1 3 768938-1 Adaptor { Figure 5 oad Rev A 3of3