NB7L1008M 2.5V / 3.3V 1:8 CML Fanout Multi-Level Inputs w/ Internal Termination Description http://onsemi.com The NB7L1008M is a high performance differential 1:8 Clock/Data fanout buffer. The NB7L1008M produces eight identical output copies of Clock or Data operating up to 6 GHz or 10.7 Gb/s, respectively. As such, the NB7L1008M is ideal for SONET, GigE, Fiber Channel, Backplane and other Clock/Data distribution applications. The differential inputs incorporate internal 50 W termination resistors that are accessed through the VT pin. This feature allows the NB7L1008M to accept various logic standards, such as LVPECL, CML, LVDS, LVCMOS or LVTTL logic levels. The VREFAC reference output can be used to rebias capacitor-coupled differential or single-ended input signals. The 1:8 fanout design was optimized for low output skew applications. The NB7L1008M is a member of the GigaCommTM family of high performance clock products. 1 32 1 QFN32 MN SUFFIX CASE 488AM A WL YY WW G NB7L 1008M AWLYYWWG G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package (Note: Microdot may be in either location) Features * * * * * * * * * * * * * * * MARKING 32 DIAGRAM Input Data Rate > 12 Gb/s Typical Data Dependent Jitter < 20 ps Maximum Input Clock Frequency > 8 GHz Typical Random Clock Jitter < 0.8 ps RMS Low Skew 1:8 CML Outputs, < 25 ps max Multi-Level Inputs, accepts LVPECL, CML, LVDS 160 ps Typical Propagation Delay 45 ps Typical Rise and Fall Times Differential CML Outputs, 400 mV Peak-to-Peak, Typical Operating Range: VCC = 2.375 V to 3.6 V, GND = 0 V Internal Input Termination Resistors, 50 W VREFAC Reference Output QFN-32 Package, 5 mm x 5 mm -40C to +85C Ambient Operating Temperature These are Pb-Free Devices SIMPLIFIED LOGIC DIAGRAM Q0 Q0 Q1 Q1 Q2 Q2 Q3 Q3 IN VT 50W 50W IN Q4 Q4 VREFAC Q5 Q5 Q6 Q6 Q7 Q7 ORDERING INFORMATION See detailed ordering and shipping information on page 9 of this data sheet. (c) Semiconductor Components Industries, LLC, 2008 December, 2008 - Rev. 0 1 Publication Order Number: NB7L1008M/D 29 28 27 VCC Q1 30 Q2 Q0 31 Q2 Q0 32 Q1 VCC NB7L1008M 26 Exposed Pad (EP) 25 VCC 1 24 GND GND 2 23 VCC IN 3 22 Q3 VT 4 21 Q3 20 Q4 NB7L1008M 18 VCC VCC 8 17 9 10 11 12 13 14 15 16 VCC 7 Q5 GND Q5 Q4 Q6 19 Q6 6 Q7 IN Q7 5 VCC VREFAC GND Figure 1. 32-Lead QFN Pinout (Top View) Table 1. PIN DESCRIPTION Pin Name I/O Description 3, 6 IN, IN LVPECL, CML, LVDS Input 4 VT 2, 7 17,24 GND Negative Supply Voltage, Note 2 1, 8, 9, 16, 18, 23, 25, 32 VCC Positive Supply Voltage, Note 2 31, 30, 29, 28, 27, 26, 22, 21, 20, 19, 15, 14, 13, 12, 11, 10 Q0, Q0, Q1, Q1, Q2, Q2, Q3, Q3, Q4, Q4, Q5, Q5, Q6, Q6, Q7, Q7 5 VREFAC - EP Non-inverted / Inverted Differential Clock/Data Input. Note 1 Internal 50 W Termination Pin for IN and IN CML Non-inverted / Inverted Differential Output. Note 1 Output Voltage Reference for Capacitor-Coupled Inputs, only - The Exposed Pad (EP) on the QFN-24 package bottom is thermally connected to the die for improved heat transfer out of package. The exposed pad must be attached to a heat-sinking conduit. The pad is electrically connected to GND and is recommended to be electrically connected to GND on the PC board. 1. In the differential configuration when the input termination pin (VT) is connected to a common termination voltage or left open, and if no signal is applied on IN/IN, then the device will be susceptible to self-oscillation. Qn/Qn outputs have internal 50 W source termination resistors. 2. All VCC and GND pins must be externally connected to the same power supply voltage to guarantee proper device operation. http://onsemi.com 2 NB7L1008M Table 2. ATTRIBUTES Characteristics ESD Protection Value Human Body Model Machine Model > 2 kV > 200 V Moisture Sensitivity (Note 3) Indefinite Time of the Drypack QFN-32 Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in Transistor Count 263 Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 3. For additional information, refer to Application Note AND8003/D. Table 3. MAXIMUM RATINGS Symbol Parameter Condition 1 Condition 2 Rating Unit VCC Positive Power Supply GND = 0 V 4.0 V VIN Input Voltage GND = 0 V -0.5 to VCC V VINPP Differential Input Voltage |IN - IN| 1.89 V IIN Input Current Through RT (50 W Resistor) $40 mA Iout Output Current 34 40 mA IVFREFAC VREFAC Sink/Source Current $1.5 mA TA Operating Temperature Range -40 to +85 C Tstg Storage Temperature Range -65 to +150 C qJA Thermal Resistance (Junction-to-Ambient) (Note 4) TGSD 51-6 (2S2P Multilayer Test Board) with Filled Thermal Vias 0 lfpm 500 lfpm QFN-32 QFN-32 31 27 C/W C/W qJC Thermal Resistance (Junction-to-Case) Standard Board QFN-32 12 C/W Tsol Wave Solder 265 C Continuous Surge Pb-Free Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 4. JEDEC standard multilayer board - 2S2P (2 signal, 2 power) with 8 filled thermal vias under exposed pad. http://onsemi.com 3 NB7L1008M Table 4. DC CHARACTERISTICS - CML OUTPUT VCC = 2.375 V to 3.6 V; GND = 0V TA = -40C to 85C (Note 6) Symbol Characteristic Min Typ Max Unit 3.0 2.375 3.3 2.5 3.6 2.625 V 265 315 mA POWER SUPPLY VCC Power Supply Voltage VCC = 3.3 V VCC = 2.5 V POWER SUPPLY CURRENT ICC Power Supply Current, Inputs and Outputs Open CML OUTPUTS (Note 5, Figures 10 and 11) VOH Output HIGH Voltage VOL Output LOW Voltage VCC = 3.3V VCC = 2.5V VCC - 30 3270 2470 VCC - 10 3290 2490 VCC 3300 2500 mV VCC = 3.3V VCC = 2.5V VCC - 600 2700 1900 VCC - 400 2900 2100 VCC - 350 2950 2150 mV DIFFERENTIAL INPUTS DRIVEN SINGLE-ENDED (Notes 7 and 8) (Figures 6 and 8) VIH Single-Ended Input HIGH Voltage Vth + 100 VCC mV VIL Single-Ended Input LOW Voltage GND Vth - 100 mV Vth Input Threshold Reference Voltage Range 1100 VCC - 100 mV VISE Single-Ended Input Voltage (VIH - VIL) 200 1200 mV VREFAC VREFAC Output Reference Voltage @ 100 mA for Capacitor - Coupled Inputs, Only VCC = 3.3 V VCC = 2.5 V VCC - 1375 VCC - 1325 VCC - 1200 VCC - 1200 VCC - 1100 VCC - 1075 mV DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (IN, IN) (Note 9) (Figures 4 and 7) VIHD Differential Input HIGH Voltage 1100 VCC mV VILD Differential Input LOW Voltage GND VIHD - 100 mV VID Differential Input Voltage (VIHD - VILD) 100 1200 mV IIH Input HIGH Current -150 40 +150 mA IIL Input LOW Current -150 5 +150 mA TERMINATION RESISTORS RTIN Internal Input Termination Resistor 45 50 55 W RTOUT Internal Output Termination Resistor 45 50 55 W NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. CML outputs loaded with 50 W to VCC for proper operation. 6. Input and output parameters vary 1:1 with VCC. 7. Vth, VIH, VIL,, and VISE parameters must be complied with simultaneously. 8. Vth is applied to the complementary input when operating in single-ended mode. 9. VIHD, VILD, VID and VCMR parameters must be complied with simultaneously. http://onsemi.com 4 NB7L1008M Table 5. AC CHARACTERISTICS VCC = 2.375 V to 3.6 V; GND = 0V TA = -40C to 85C (Note 10) Symbol Min Typ fDATA Maximum Operating Input Data Rate Characteristic 10 12 Max Gb/s Unit fINCLK Maximum Input Clock Frequency, VOUTPP w 200 mV 6 8 GHz VOUTPP Output Voltage Amplitude (see Figures 2 and 5, Note 11) fin v 4 GHz fin v 6 GHz 200 200 400 350 VCMR Input Common Mode Range (Differential Configuration, Note 12, Figure 9) 1050 tPLH, tPHL Propagation Delay to Output Differential, IN/IN to Qn/Qn 100 160 tPLH TC Propagation Delay Temperature Coefficient -40C to +85C tDC Output Clock Duty Cycle fin v 6 GHz 45 49/51 55 % tSKEW Duty Cycle Skew (Note 13) Within Device Skew (Note 14) Device to Device Skew (Note 15) 0.15 7 25 1 25 70 ps tJITTER Clock Jitter RMS, 1000 Cycles (Note 16) fin v 6 GHz Data Dependent Jitter (DDJ) (Note 17) v10 Gb/s 0.2 3 0.8 20 ps VINPP Input Voltage Swing (Differential Configuration) (Note 18) (Figure 5) 100 1200 mV tr, tf Output Rise/Fall Times (20% - 80%) Qn, Qn 20 70 ps mV VCC - 50 mV 250 ps 35 fs/C 45 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 10. Measured using a 400 mV source, 50% duty cycle 1 GHz clock source. All outputs must be loaded with external 50 W to VCC. Input edge rates 40 ps (20% - 80%). 11. Output voltage swing is a single-ended measurement operating in differential mode. 12. VCMR min varies 1:1 with GND, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. 13. Duty cycle skew is measured between differential outputs using the deviations of the sum of Tpw- and Tpw+ @ 1 GHz. 14. Within device skew compares coincident edges. 15. Device to device skew is measured between outputs under identical transition 16. Additive CLOCK jitter with 50% duty cycle clock signal. 17. Additive Peak-to-Peak jitter with input NRZ data at PRBS23. 18. Input voltage swing is a single-ended measurement operating in differential mode. . OUTPUT VOLTAGE AMPLITUDE (mV) 500 VCC 450 Q Output Amplitude (mV) 400 IN 350 50 W VT 300 50 W IN 250 200 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 fout, CLOCK OUTPUT FREQUENCY (GHz) Figure 2. Output Voltage Amplitude (VOUTPP) vs. Input Frequency (fin) at Ambient Temperature (Typical) http://onsemi.com 5 Figure 3. Input Structure NB7L1008M IN VID = |VIHD(IN) - VILD(IN)| IN Q VIHD IN VINPP = VIH(IN) - VIL(IN) IN VILD VOUTPP = VOH(Q) - VOL(Q) Q tPHL tPLH Figure 4. Differential Inputs Driven Differentially VIH Figure 5. AC Reference Measurement IN IN IN IN Vth VIL Vth Figure 6. Differential Input Driven Single-Ended VCC Vthmax Vth VCC VIHmax VILmax IN Vthmin GND Figure 7. Differential Inputs Driven Differentially VIHDmax VCMmax IN VIH Vth VIL VCMR VIHmin VILmin IN VCMmin GND Figure 8. Vth Diagram VILDmax VID = VIHD - VILD VIHDtyp VILDtyp VIHDmin VILDmin Figure 9. VCMR Diagram http://onsemi.com 6 NB7L1008M VCC 50 W 50 W Zo = 50 W Q D Receiver Device Driver Device Q D Zo = 50 W Figure 10. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8173/D) NB7L1008M VCCO VCC (Receiver) 50 W 50 W Q 50 W 50 W Q 16 mA GND Figure 11. Typical CML Output Structure and Termination http://onsemi.com 7 NB7L1008M VCC VCC NB7L1008M ZO = 50 W LVPECL Driver VCC VCC ZO = 50 W IN 50 W VT = VCC - 2 V ZO = 50 W LVDS Driver 50 W 50 W 50 W IN GND GND GND GND Figure 12. LVPECL Interface Figure 13. LVDS Interface VCC CML Driver IN VT = Open ZO = 50 W IN VCC VCC VCC NB7L1008M ZO = 50 W NB7L1008M ZO = 50 W IN 50 W VT = VCC ZO = 50 W Differential Driver 50 W NB7L1008M IN 50 W VT = VREFAC* ZO = 50 W IN 50 W IN GND GND GND Figure 15. Capacitor-Coupled Differential Interface (VT Connected to VREFAC) Figure 14. Standard 50 W Load CML Interface GND *VREFAC bypassed to ground with a 0.01 mF capacitor VCC VCC ZO = 50 W Differential Driver NB7L1008M IN 50 W VT = VREFAC* 50 W IN GND Figure 16. Capacitor-Coupled Single-Ended Interface (VT Connected to VREFAC) http://onsemi.com 8 GND NB7L1008M ORDERING INFORMATION Package Shipping NB7L1008MMNG Device QFN32 (Pb-Free) 74 Units / Rail NB7L1008MMNR4G QFN32 (Pb-Free) 1000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 9 NB7L1008M PACKAGE DIMENSIONS PIN ONE LOCATION 2X EE EE 0.15 C 2X QFN32 5*5*1 0.5 P CASE 488AM-01 ISSUE O A B D NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM TERMINAL 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. E DIM A A1 A3 b D D2 E E2 e K L TOP VIEW 0.15 C (A3) 0.10 C A 32 X 0.08 C C L 32 X 9 D2 SEATING PLANE A1 SIDE VIEW MILLIMETERS MIN NOM MAX 0.800 0.900 1.000 0.000 0.025 0.050 0.200 REF 0.180 0.250 0.300 5.00 BSC 2.950 3.100 3.250 5.00 BSC 2.950 3.100 3.250 0.500 BSC 0.200 --- --- 0.300 0.400 0.500 SOLDERING FOOTPRINT* EXPOSED PAD 16 K 5.30 32 X 17 8 3.20 E2 1 32 X 0.63 24 32 25 32 X b 0.10 C A B 3.20 e 5.30 0.05 C BOTTOM VIEW 32 X 0.28 28 X 0.50 PITCH *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. GigaComm is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NB7L1008M/D