AFBR-5978Z Digital Diagnostic 650nm Transceiver for Fast Ethernet (10/100 Mbps) with SC-RJ connector Data Sheet Description Features The AFBR-5978Z transceiver provides the system designer with the ability to implement Fast Ethernet (100 Mbps) or Ethernet (10 Mbps) over 50 meter standard bandwidth 0.50.05 NA POF and 100 meter standard bandwidth 0.370.04 NA HCS fiber. The connectivity available for the transceiver is SC-RJ. This product is lead free and compliant with RoHS. Compatible with electrical and optical performance of the POFAC recommendations for the Fast Ethernet over Plastic Optical Fiber (POF). Compatible with the Electrical and Optical performance of the ProfiNet recommendations the Fast Ethernet over POF and Hard-Clad Silica Fiber (HCS). Manufactured in an ISO 9001 certified facility DMI [Digital Diagnostics Monitoring Interface, SFF-8472 Rev 9.3], provides real-time monitoring of: - Temperature - Supply voltage - Received Optical Power (Alarm/Warning flag) LVPECL Signal Detect Output Temperature range -25 to +85 C Transmitter The transmitter contains a 650nm LED with an integrated driver. The LED driver operates at 3.3 V. It receives a LVPECL compatible electrical input, and converts it into a modulated current driving the LED. The LED is packaged in an optical subassembly, part of the transmitter section. The optical subassembly couples the output optical power efficiently into POF or HCS fiber. Receiver The receiver utilizes a Si PIN photodiode. The PIN photodiode is packaged in an optical sub-assembly, part of the receiver section. This optical subassembly couples the optical power efficiently from POF or HCS fiber to the receiving PIN. The integrated IC operates at 3.3 V and converts the photocurrent into LVPECL compatible electrical output. Package The transceiver package consist of four basic elements; two optical subassemblies, an electrical subassembly and the housing as illustrated in the block diagrams in Figure 1. The package outline drawing and pin out are shown in Figures 2 and 3. Applications Factory automation at Fast Ethernet speeds Fast Ethernet networking over POF and HCS Link Distance up to 50 m POF or 100 m HCS (See application note 5290 for details) HCS(R) is a trademark of OFS Corporation AFBR-5978Z is compatible with the SC-RJ Connecting System from Reichle & De-Massari AG, Switzerland Block diagram SC-RJ RECEPTACLE ELECTRICAL SUBASSEMBLY DIFFERENTIAL DATA OUT PIN PHOTODIODE SINGLE-ENDED SIGNAL DETECT OUT QUANTIZER IC PREAMP IC OPTICAL SUBASSEMBLIES DMI DIFFERENTIAL LED DATA IN DRIVER IC TOP VIEW Figure 1. Block diagram The optical subassemblies utilize a high volume assembly process together with low cost lens elements which result in a cost effective building block. The electrical subassembly consists of a high volume multilayer printed circuit board on which the IC chips and various surface mounted passive circuit elements are attached. The housing includes internal shields for the electrical and optical subassemblies to insure low EMI emissions and high immunity to external EMI fields. The outer housing including the duplex SC-RJ connector is molded of filled non-conductive plastic to provide me- Figure 2. Package outline drawing. 2 chanical strength and electrical isolation. The low profile of the Avago Technologies transceiver design complies with the maximum height allowed for the duplex SC-RJ connector over the entire length of the package. The transceiver is attached to a printed circuit board with twelve signal pins and the two solder posts, which exit the bottom of the housing. The two solder posts provide the primary mechanical strength to withstand the mechanical loads imposed on the transceiver by mating with the SC-RJ connectored fiber cables. The solder posts are isolated from the circuit design of the transceiver and do not require connection to a ground plane on the circuit board Pin Descriptions Pin 1 Sda: the data line of the two wire serial interface. This data line should be pulled up with a 4.7k-10k resistor on the host board to a supply of 3.3V 10%. Pin 2 Rx GND: receiver ground pin. Directly connect this pin to the receiver ground plane of the host board. Pin 3 Rx Vcc: receiver power supply pin. Provide +3.3 V DC via a receiver power supply filter circuit. Locate the power supply filter circuit as close as possible to the Vcc Rx pin. Pin 4 Sd: signal detect pin. If an optical signal is present at the input of the receiver, Sd output is a logic "1". Absence of an optical signal to the receiver results in a logic "0" output. This signal detect output can be used to drive a LVPECL input on an upstream circuit, such as Signal Detect input or Loss of Signal-bar. Proper LVPECL termination should be in place. See figure 4. Pin 5 Rdata-: receiver data out bar. This data line is a 3.3V LVPECL compatible differential line which should be properly terminated with a 130 pull up to Vcc and 82 pull down to ground. Pin 6 Rdata+: receiver data out. This data line is a 3.3V LVPECL compatible differential line which should be properly terminated with a 130 pull up to Vcc and 82 pull down to ground. SC-RJ connector Sda RxGND RxVcc Sd RdataRdata+ Scl TdataTdata+ Txdis TxGND TxVcc bottom view Figure 3. Pin Out diagram 3 Pin 7 Tx Vcc: transmitter power supply. Provide +3.3V DC via a transmitter power supply filter circuit. Locate the power supply filter circuit as close as possible to the Vcc Tx pin. Pin 8 Tx GND: transmitter ground. Directly connect this pin to the transmitter ground plane on the host board. Pin 9 Txdis: transmitter disable input. This input is used to shut down the transmitter light output. It is internally pulled up with a ~8 k resistor. Low (0-0.8 V) - transmitter on Between (0.8-2.0 V) - undefined High (2.0-3.63 V) - transmitter off Open - transmitter off Pin 10 Tdata+: transmitter data in. This data line is an AC coupled 100 differential line which does not need any termination at the user SERDES. The AC coupling is done inside the module and therefore not required on the host board. Pin 11 Tdata-: transmitter data in bar. This data line is an AC coupled 100 differential line which does not need any termination at the user SERDES. The AC coupling is done inside the module and therefore not required on the host board. Pin 12 Scl: the clock line of the two wire serial interface. This data line should be pulled up with a 4.7k - 10 k resistor on the host board to a supply of 3.3V 10%. V cc 3.3V 10F 1H 0.1F 1H 0.1F Tx disable 10nF Z = 50 TD+ Z = 50 TD- 130 10F 130 RD+ RD82 0.1F AFBR-5978Z LED driver 10nF Z = 50 RxVcc Rdata+ Z = 50 RdataSd 82 PC Master Signal Detect TxVcc Tdata- V cc 3.3V 100 Txdis Tdata+ Protocol IC & SERDES Sda 82 4.7k-10k 4.7k-10k Amplifier & Quantisizer EEPROM Scl V cc 3.3V 130 V cc 3.3V Figure 4. Recommended termination circuit. Board Layout - Decoupling Circuit and Ground Planes Functional Data I/O It is important to take care in the layout of your circuit board to achieve optimum performance from the transceiver. A power supply decoupling circuit is recommended to filter out noise to assure optimal product performance. It is further recommended that a contiguous ground plane be provided in the circuit board directly under the transceiver to provide a low inductance ground for signal return current. This recommendation is in keeping with good high frequency board layout practices. The LVPECL receiver output of the Avago Technologies transceiver can be DC-coupled to the LVPECL compliant network interface through a Thevenin equivalent transformation. For a 3.3V power supply the LVPECL outputs should be pulled up to Vcc with a 130 resistor and pulled down to ground with an 82 resistor. Both coupling resistors are preferably placed close to the network interface IC, see figure 4. AC-coupling can be used for systems in which the transceiver and connected logic are at different supply voltages. For AC coupling, the coupling capacitor should be large enough to avoid excessive low-frequency droop when the data signal contains long strings of consecutive identical digits. The LVPECL outputs have to be pulled down to ground first to DC bias the output before AC coupling. Because the LVPECL output common-mode voltage is fixed at Vcc - 1.3V, the DC-biasing resistor can be selected by assuming 14 mA DC current. This results in a bias-resistor value of 142 - 200. After the AC-coupling capacitors, a Thevenin equivalent transformation connects to the LVPECL compatible network interface, equal to the one used in DC-coupling. 4 Digital Diagnostics Monitoring Interface The AFBR-5978Z transceiver features an enhanced digital diagnostic interface, compliant to the "Digital Diagnostic Monitoring Interface for Optical Transceivers" SFF-8472 Multi-source Agreement (MSA). Please refer to the MSA document to access information on the range of options, both hardware and software, available to the host system for exploiting the available digital diagnostic features. The diagnostic monitoring interface (DMI) has two 256 byte memory maps in EEPROM which are accessible over a two wire interface: the serial ID memory map at address 1010000X (0xA0) and the digital diagnostic memory map at address 1010001X (0xA2). The enhanced digital interface allows real-time access to device operating parameters, and includes optional digital features such as soft control and monitoring of I/O signals. In addition, it fully incorporates the functionality needed to implement digital alarms and warnings, as defined by the SFF-8472 MSA. With the digital diagnostic monitoring interface, the user has capability of performing component monitoring, fault isolation and failure prediction in their transceiver-based applications. The digital diagnostic memory map contains device operating parameters and alarm and warning flags. The operating parameters are to be retrieved through a sequential read command ensuring that the MSB and LSB of each parameter are "coherent". Furthermore, it contains 120 bytes that can be written by the user as well as a writable soft control byte. 2 wire address 1010000X (A0h) 0 Serial ID Defined by SFP MSA (96 bytes) 2 wire address 1010001X (A2h) 0 Alarm and Warning Thresholds (56 bytes) 55 Cal Constants (40 bytes) 95 Vendor Specific (32 bytes) 127 Time Diagnostic Interface (24 bytes) 119 Vendor Specific (8 bytes) 127 Reserved in SFP MSA (128 bytes) User Writable EEPROM (120 bytes) 247 255 255 Vendor Specific (8 bytes) Figure 5. Digital diagnostic memory map - specific data field description (from SFF-8472 MSA) 5 The serial ID memory map contains a serial identification and vendor specific information and is read only. Tables 1 to 6 detail memory contents, timing characteristics, soft commands and alarm/warning flags. Table 1. Transceiver soft diagnostics Timing characteristics Parameter Symbol Hardware TX_DISABLE assert time Min Max Unit Notes t_off 10 s Note 1, Figure 6 Hardware TX_DISABLE negate time t_on 1 ms Note 2, Figure 6 Time to initialize t_init 100 ms Note 3, Figure 6 Hardware RX_SD assert time t_sd_on 100 s Note 4 Hardware RX_SD de-assert time t_sd_off 100 s Note 5 Software TX_DISABLE assert time t_off_soft 100 ms Note 6 Software TX_DISABLE negate time t_on_soft 100 ms Note 7 Software RX_SD assert time t_sd_on_soft 100 ms Note 8 Software RX_SD de-assert time t_sd_off_soft 100 ms Note 9 Analog parameter data ready t_data 1000 ms Note 10 Serial bus hardware ready t_serial 300 ms Note 11 Write cycle time t_write 10 ms Note 12 Serial ID clock rate f_serial_clock 400 kHz Note 13 Notes: 1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal. 2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal. 3. Time from Power on or falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal. 4. Time from valid optical signal to RX_SD assertion. 5. Time from loss of optical signal to RX_SD de-assertion. 6. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured from falling clock edge after stop bit of write transaction. 7. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte110, bit 6) to when the modulated optical output rises above 90% of nominal. 8. Time for two-wire interface assertion of RX_SD (A2h, byte 110, bit 1) from presence of valid optical signal. 9. Time for two-wire interface de-assertion of RX_SD (A2h, byte 110, bit 1) from loss of optical signal. 10. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is operational. 11. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h). 12. Time from stop bit to completion of a 1-8 byte write command. 13. Contact Avago Technologies for applications at faster (>400 kHz) Serial ID clock rates. 6 Table 2. Transceiver Digital Diagnostic Monitor Characteristics Parameter Symbol Min. Unit Notes Transceiver internal temperature accuracy TINT 5.0 C Temperature is measured internal to the transceiver. Valid from -25C to 85C case temperature. Transceiver internal supply voltage accuracy VINT 0.1 V Supply voltage is measured internal to the transceiver and can, with less accuracy, be correlated to voltage at the Vcc pin. Valid over 3.3V 10%. V CC > 2.97 V V CC > 2.97 V TX_DIS ABL E TX_DIS ABL E Trans mitted Signa l Trans mitted Signa l t_init t_init t-init: TX_DISABLE ASSERTED t-init: TX_DISABLE NEGATED occurrence of loss Optical Signal TX_DIS ABL E SD Trans mitted Signa l t_SD_off t_SD_on tx-SD-on & tx-SD-off t_off t-off & t-on: TX DISABLE ASSERTED THEN NEGATED Figure 6. Transceiver timing diagrams. Mechanical dimension - Dust cap 23.3 9 11.35 14.35 12.8 Front Right 8.5 6.1 3 Bottom Mechanical Dimensions in Millimeters 7 Iso t_on Table 3. EEPROM Serial ID Memory Contents - Address A0h Addr Hex ASCII 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20 41 A 60 02 Note 1 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 56 41 47 4F 20 54 45 43 48 20 20 20 20 20 20 00 00 17 V A G O 61 62 63 64 65 66 67 68 - 83 84 - 91 92 93 94 95 96 - 127 8A 00 Note 1 Note 1 Note 4 39 6A T E C H Description Addr Hex ASCII 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 41 46 42 52 2D 35 39 37 38 5A 20 20 20 20 20 20 20 20 20 20 A F B R 5 9 7 8 Z Description 00 14 00 00 Note 2 Note 3 68 D0 01 h Note 4 Note 5 Notes: 1. LED wavelength is represented in 16 unsigned bits. The hex representation of 650 (nm) is 0x28A. 2. Address 68-83 specify a unique module serial number. 3. Address 84-91 specify the date code. 4. Address 63 is the checksum for bytes 0-62 and address 95 is the checksum for bytes 64-94. They are calculated (per SFF-8472) and stored prior to product shipment. 5. Address 96-127 is vendor specific. 8 Table 4. EEPROM DMI Memory Contents - Address A2h Addr Hex Dec Description Addr 0 73 115 Temp H alarm MSB[1,5] 95 Checksum for bytes 0 to 94[7] 1 00 0 Temp H alarm LSB[1,5] 96 Real time temperature MSB[1] 2 D8 216 Temp L alarm MSB[1,5] 97 Real time temperature LSB[1] 3 00 0 Temp L alarm LSB[1,5] 98 Real time Vcc MSB[2] 4 69 105 Temp H warning MSB[1,5] 99 Real time Vcc LSB[2] 5 00 0 Temp H warning LSB[1,5] 100 to 109 Reserved[8] 231 Temp L warning MSB[1,5] 110 Status control - see table 5 111 Reserved[8] 6 E7 Hex Dec Description 7 00 0 Temp L warning LSB[1,5] 8 98 152 Vcc H alarm MSB[2,5] 112 Flag bit - see table 6 88 Vcc H alarm LSB[2,5] 113 Flag bit - see table 6 114 Reserved[8] 9 58 10 69 105 Vcc L alarm MSB[2,5] 11 78 120 Vcc L alarm LSB[2,5] 115 Reserved[8] 12 8D 141 Vcc H warning MSB[2,5] 116 Flag bit - see table 6 204 Vcc H warning LSB[2,5] 117 Flag bit - see table 6 118 Reserved[8] 13 CC 14 74 116 Vcc L warning MSB[2,5] 15 04 4 Vcc L warning LSB[2,5] 119 to 127 Vendor specific 16 to 39 Reserved[8] 128 to 247 Customer writable 40 8 Rx OMA Margin L alarm[3,4,5] 248 to 255 Vendor specific 18 Rx OMA Margin L warning[3,4,5] 41 42 to 55 08 12 Reserved[8] Notes: 1. Temperature (Temp) is decoded as a 16 bit signed twos complement integer in increments of 1/256 C. 2. Supply voltage (Vcc) is decoded as a 16 bit unsigned integer in increments of 100 V. 3. Received optical modulation amplitude margin or Rx OMA margin is a measure for the reserve in OMA to Sensitivity. 4. Received OMA margin is decoded as an 8 bit signed twos compliment integer in increments of 0.2 dB. 5. This register is read only. A write will be acknowledged but not stored. 6. Bytes 56-94 are not intended for use with AFBR-5978Z, but have been set to default values per SFF-8472. 7. Byte 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment. 8. Reserved registers will return "00" when read. A write to a reserved register will be acknowledged but not stored. 9 Table 5. EEPROM Serial ID Memory Contents - Soft Commands (Address A2h, byte 110) Bit # Status / Control name Description Notes 7 TX_DISABLE State Digital state of TX_DISABLE input pin (logic 1 = TX_DISABLE asserted) Note 1 6 Soft TX_DISABLE Read/write bit for changing digital state of TX_DISABLE function Note 1,2 5 Reserved Note 3 4 Not supported Note 4 3 Not supported Note 5 2 Not supported Note 6 1 RX_SD State Digital state of the RX_SD output pin (logic 0 = RX_SD asserted) Note 1 0 Data Ready (Bar) Indicates transceiver is powered and real time sense data is ready(0 = ready) Note 7 Notes: 1. The response time for soft commands of the AFBR-5978Z is 100 ms as specified by the MSA SFF-8472. 2. Bit 6 is logic OR'd with the TX_DISABLED input pin. Either asserted will disable the transmitter. 3. Reserved bits will return "0" when read. A write to a reserved bit will be acknowledged but not stored. 4. A read from bit 4 will return "1". A write will be acknowledged but not stored. 5. A read/write from/to bit 3 will be acknowledged and stored but will be ignored by the transceiver. 6. A read from bit 2 will return "0". A write will be acknowledged but not stored. 7. AFBR-5978Z meets the MSA SFF-8471 data ready timing of 1000 ms. Table 6. EEPROM Serial ID Memory Contents - Alarm and Warnings (Address A2h, bytes 112, 113, 116, 117) Byte Bit Flag bit name Description 112 7 Temp high alarm Set when transceiver internal temperature exceeds high alarm threshold 6 Temp low alarm Set when transceiver internal temperature exceeds low alarm threshold 5 Vcc high alarm Set when transceiver internal supply voltage exceeds high alarm threshold 4 Vcc low alarm Set when transceiver internal supply voltage exceeds low alarm threshold 3-0 Reserved Note 1 7-6 Reserved Note 1 5 Rx OMA Margin low alarm Set when received Rx OMA Margin exceeds low alarm threshold, Note 2 4-0 Reserved Note 1 7 Temp high warning Set when transceiver internal temperature exceeds high warning threshold 6 Temp low warning Set when transceiver internal temperature exceeds low warning threshold 5 Vcc high warning Set when transceiver internal supply voltage exceeds high warning threshold 4 Vcc low warning Set when transceiver internal supply voltage exceeds low warning threshold 3-0 Reserved Note 1 7-6 Reserved Note 1 5 Rx OMA Margin low warning Set when receiver Rx OMA Margin exceeds low warning threshold, Note 2 4-0 Reserved Note 1 113 116 117 Notes: 1. Reserved bits will return "0" when read. A write to a reserved bit will be acknowledged but not stored. 2. Received optical modulation amplitude margin or Rx OMA margin is a measure for the reserve in OMA to Sensitivity. 10 Regulatory Compliance Table Feature Test Method Performance MIL-STD 883 Method 3015, 100 pF / 1.5 k 5 pulse per polarity ESD resistance Human Body Model 2 kV IEC 61000-4-2 Typically withstand an electrostatic discharge without damage when the SC-RJ connector receptacle is contacted by a Human Body Model probe Level 3Air discharge ESD resistance 8 kV Contact discharge ESD resistance 6 kV IEC 61000-4-3 Typically show no measurable effect from an electric field applied to the transceiver when mounted to a circuit board without chassis enclosure. Level 3 10 V/m Electric field immunity: EN60825-1 As specified in IEC 60825-1 version 1.2. AEL Class 1 TUV Certificate number R72062581 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operation conditions. It should not be assumed that limiting values of more than one parameter can be applied to the products at the same time. Exposure to the absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Min Max Storage Temperature Ts -40 +100 C Case Operating Temperature TC -25 +85 C Lead Soldering Temperature Tsold 260 C Note 1 Lead Soldering Time tsold 10 s Note 1 Supply Voltage Vcc -0.5 4.0 V Data Input Voltage Vi -0.5 VCC V Differential Input Voltage VD 2.0 V Output Current PECL IDout -50 50 mA ESD-Resistance - Human Body Model VESD -2 +2 kV Note 2 ESD-Resistance - Air Discharge VESD -8 +8 kV Note 3 ESD-Resistance - Contact Discharge VESD -6 +6 kV Note 4 Electric Field Immunity VEMI 15 V/m IEC 61000-4-3 Notes: 1. The transceiver is Pb-free wave solderable. 2. Human Body Model: 100pF/1.5k, 5 pulse / polarity; MIL-STD.883 Meth. 3015. 3. Air discharge IEC 61000-4-2 level 3 ESD-Resistance for the transceiver. 4. Contact discharge IEC 61000-4-2 level 3 ESD Resistance for the transceiver. 11 Unit Notes peak to peak Recommended Operating Conditions Parameter Symbol Min Case Operating Temperature TC -25 Supply Voltage Vcc 2.97 Differential Input Voltage VD 0.4 Data and Signal Detect Output Load RL 50 Signalling rate (Fast-Ethernet) B 125 MBd 4B/5B, 5 Signalling rate (Ethernet) B 20 MBd Manchester, 5 Humidity Typ Max Unit +85 C 3.3 3.63 V 0.800 1.6 V 5 95 % Typ Max Unit 300 mA Notes peak to peak Notes: 5. Ethernet and Fast Ethernet optical auto-negotiation signals over a 1 MHz carrier are supported. Transceiver Electrical Characteristics Parameter Symbol Min Supply Current Icc 250 Power Dissipation PDISS 825 Power Supply Noise Reduction PSNI 50 Parameter Symbol Min Data In Current - Low IDin -2 A Data In Current - High IDin 18 A Notes mW mV peak to peak Unit Notes Transmitter Electrical Characteristics 12 Typ Max Transmitter Optical Characteristics Parameter Symbol Min Typ Max Unit Notes Average Launched Power (1mm POF, NA=0.5) Po -8.5 -4.5 -2 dBm note 6 Average Launched Power (200um HCS, NA=0.37) Po -19.5 -15 -11 dBm note 6 Optical Modulation Amplitude (POF) OMA -6.5 -3 -0.5 dBm peak to peak, note 6 Optical Modulation Amplitude (HCS) OMA -17.5 -13.5 -9.5 dBm peak to peak, note 6 Central Wavelength c 635 650 660 nm note 6, 7 Spectrum RMS 17 nm note 6, 8 Optical Rise Time (10%-90%) tr 2.7 6.5 ns note 6 Optical Fall Time (10%-90%) tf 2.7 6.5 ns note 6 Duty Cycle Distortion Contributed by the Transmitter DCD +1 ns peak to peak, note 6 Random Jitter Contributed by the Transmitter RJ 0.2 ns peak to peak, note 6 Overshoot Ov 40 % note 6 Notes: 6. Measured at the end of 1 meter optical fiber. 7. Central wavelength is defined as: N c = Pii i =1 N Pi Ref: EIA/TIA standard FOTP-127/6.1, 1991 i =1 8. Spectrum RMS is defined as: 1 N 2 2 i =1 Pii 2 = N - c Pi i =1 Ref: EIA/TIA standard FOTP-127/6.3, 1991 13 -1 Receiver Electrical Characteristics Parameter Symbol Data Output Voltage - Low VOL-Vcc Min Typ -1.63 Max V Data Output Voltage - High VOH-Vcc -0.99 V Data Output Voltage Swing |VOH-VOL| Data Output Rise Time tr Data Output Fall Time tf Duty Cycle Distortion DCD Data Dependent Jitter (rise/fall) DDJ Random Jitter RJ Signal Detect Output Voltage - Low VOL-Vcc Signal Detect Output Voltage - High VOH-Vcc 400 Unit Notes 800 mV 1.45 2.20 ns 0.98 2.20 ns +1 ns peak to peak 0.6 1.5 ns peak to peak 0.1 0.2 ns peak to peak -2.2 -1.63 -1.5 V -1.2 -0.99 -0.7 V -1 single ended Receiver Optical Characteristics Parameter Symbol Min Typ Unit Notes Unstressed receiver sensitivity, OMA (POF) OMA -22.5 -25 dBm peak-peak, note 9 Unstressed receiver sensitivity, OMA (HCS) OMA -26.3 -29.3 dBm peak-peak, note 9 Input Optical Power Maximum, OMA (POF) PIN MAX +1 dBm peak-peak, note 10 Input Optical Power Maximum, OMA (HCS) PIN MAX -4 dBm peak-peak, note 10 Operating Wavelength R 660 nm Signal Detect Asserted PA 2 dB note 11 Signal Detect De-asserted PD 5 dB note 11 Signal Detect Hysteresis PA - PD 3 dB 635 1.5 650 Max Notes: 9. Measured with PRBS 27-1 sequence, BER < 2.5x10-10 . 10. Input Optical Power Maximum is defined as the maximum optical modulation amplitude where the receiver duty cycle distortion reaches 1 ns. 11. Signal Detect Asserted and De-asserted levels are indicated as dB below unstressed receiver sensitivity level for either POF or HCS. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2012 Avago Technologies. All rights reserved. Obsoletes AV01-0507EN AV02-1505EN - February 16, 2012