22
Contura Accessories
V-SERIESContura II & IIIContura IVContura XII Contura X & XI
Contura Connectors
Contura X Boot
Contura II, II & IV Actuator Removal Tool
Contura Accessories
To easily integrate Contura products into your system, Carlingswitch also offers many accessories, including:
MARKING DETAIL
REAR VIEW
45
B
APACKARD 630
7
AMP, PACKARD 586
.770[19.56]
1.0-2.0
20-18 .5-.8
2
ORIEN-
TATION
WIRE
RANGE
(2)16-14 (2)1.0-2.0
12 3.0
.950[24.13]
TANG
SYMBOL
MM
(REF)
B
AWG
16-14
20-22
20-18 .35-.5
.5-.8
(2) 16 (2) 1.3
22-18
(2).5-.8
3.012 1.0-2.0
.3-.9
B
A
18-14
16-14
(2)22-18
16-12 1.3-3
.8-2
.820[20.83]
42100-1
60295-1
02965470
02965469
PART NO
02965580
COMPANY
SERIES
02965471
PACKARD
58 SERIES
PLAIN
BRASS
.820[20.83]
AMP
250 SERIES
FASTIN-FASTON
PACKARD
METRI-PACK
630 SERIES 12015832
60253-1
MARKING DETAIL
REAR VIEW
AMP, PACKARD 58
59
AMP
A
B
67 231
PACKARD 630
4
VC2
8
VB1-01
CONTURA X BOOT
1.466[37.24]
MARKING DETAIL
FRONT VIEW
10
VC1 VC2
128
AMP
6
B
A
9
3
VC2
CONNECTOR HOUSING
(For AMP terminals only)
VRT
ACTUATOR REMOVAL
TOOL
(For flush bracket)
1.050[26.67]
1.266[32.16]
.757[19.23]
.900 [22.86]
TOP
HOLD FLUSH ON BRACKET AND PUSH
IN
TOP
INSERT POINTS UNDER
ACTUATOR
VC1
CONNECTOR HOUSING
PACKARD 630
MARKING DETAIL
FRONT VIEW
210 817
AMP, PACKARD 58
A
1.266[32.16]
VC1
4
B
3
06288318
12010601
Q.C. SELECTION GUIDE
42100-2
60295-2
12020035
12052222
60253-2
12015869
12052224
12015870
TIN
PLATED
BRASS
NOTE: Consult Delphi Packard and/or Amp on actual part numbers and availability.
AMP is a registered trademark of AMP Inc. Harrisburg, PA
Delphi Packard is a registered trademark of Delphi-Packard Electrical Systems Warren, Ohio
3.0
12
TANG SYMBOL =
PACKARD 630
MARKING DETAIL
REAR VIEW
5
AMP, PACKARD 58
12084590
2.000[50.80]
3.99 [101.35]
1.466[37.24]
.920[23.37] .920[23.37] 1.170[29.72]
1.250[31.75]
MARKING DETAIL
FRONT VIEW
VCH
CONNECTOR HOUSING
SHOWS ORIENTATION OF TANG IN SLOT
23
V-SERIES Contura II & III Contura IV Contura X & XI Contura XII
Contura Accessories
Contura Mounting Panels
Contura Hole Plug
VMS
MOUNTING
PANEL
DETAIL VIEW
VH2
HOLE PLUG
(With wing serrations)
.960 [24.38]
.080 [2.03]
.984 [25.00]
1.90 [48.2]
2.02[51.3]
1.90[48.2]
+.008[.2]
-.000[.0]
+.008[+.
20]
-.000[-.00]
VMS
MOUNTING PANEL
HOLE
TEST
CUT
HOLE IN
ACTUAL
MATERIAL
+.008[.2]
-.000[.0]
+.008[+.20]
-.000[-.00]
TEST CUT
HOLE IN
ACTUAL
MATERIAL
MOUNTING PANEL
OPENING
(2) UNITS
1.030 [26.16]
.670 [17.01]
1.034[26.26]
VMM
MOUNTING PANEL
MIDDLE
.960 [24.38]
1.240 [31.50]
VH1
HOLE PLUG
(No wing serrations)
(With VC1 connector attached)
DETAIL VIEW
VH1
HOLE PLUG
(No wing serrations
for ease of removal)
1.450[36.83]
.830[21.08]
TEST CUT
HOLE IN
ACTUAL
MATERIAL
PLUG
MOUNTING HOLE
VM6
MOUNTING PANEL
1.820 [46.23]
.430[10.92]
.960[24.38]
1.900 [48.26]
2.300[58.42] 1.970[50.03]
MOUNTING PANEL
For additional units, add 1.03[26.2] per unit.
For more than 2 V-Series Switches, add
middle section. Available in Panel Thicknesses
listed below. Consult factory.
MOUNTING PANEL THICKNESS
.062[1.57] .187[4.75]
.093[2.36] .250[6.35]
.125[3.17] .375[9.52]
VME
MOUNTING
PANEL
END
1.910[48.51]
2.300[58.42]
3.400 [86.36]
VM3
MOUNTING PANEL
VHP
MOUNTING PANEL PLUG
1.187[30.14]
1.030 [26.16]
1.460 [37.08]
6.490 [164.85]
2.300 [58.42]
1.340 [34.03]
VH2
HOLE PLUG
(With wing serrations)
1.700 [43.18]
2.300 [58.42]
1.900 [48.26]
