DATA SHEET
Product specification
File under BCcomponents, BC08
2000 Aug 08
BCcomponents
5063JD series (space miser)
0.25 to 0.40 W; 1% and 5%
Metal film resistors
www.DataSheet4U.com
2000 Aug 08 2
BCcomponents Product specification
Metal film resistors 5063JD series (space miser)
0.25 to 0.40 W; 1% and 5%
DESCRIPTION
A homogeneous film of metal alloy is deposited on a high grade BALOX ceramic body. After a helical groove has been cut
in the resistive layer, tinned connecting wires of electrolytic copper are welded to the end-caps. The resistors are coated
with a blue lacquer which provides electrical, mechanical, and climatic protection. The encapsulation is resistant to all
cleaning solvents in accordance with “MIL-STD-202E, method 215”, and “IEC 60068-2-45”.
QUICK REFERENCE DATA
DESCRIPTION VALUE
Resistance range 0.22 Ωto 10 MΩ; see Table 1
Resistance tolerance and series ±5%, (E24); ±1%, (E24/E96)
Temperature coefficient ±100 ×10−6/K
Operation mode normal long term
Climatic category (LCT/UCT/days) 55/155/56 55/125/56
Max. dissipation, P70 0.40 W 0.25 W
Thermal resistance, Rth 200 °C/W
Max. continuous operating voltage, Umax 200 V (DC or RMS)
Noise R ≤1MΩmax. 0.1 V/V
Surface temperature 155 °C 125 °C
Operating temperature range −55 °C to +155 °C−55 °C to +125 °C
Max. resistance change at P70 for resistance range,
∆R/R max., after:
1000 h 0.50%0.25%
8000 h 1.0%0.50%
225000 h −1.5%
Permissible voltage against ambient:
1 minute 300 V
continuous 75 V
Stability (∆R/R max.) after:
load (1000 hours) ±0.50% + 0.05 Ω±0.25% + 0.05 Ω
climatic test ±1.0% + 0.05 Ω
resistance to soldering heat ±0.25% + 0.05 Ω
short time overload (400 V max.) ±0.25% + 0.05 Ω
www.DataSheet4U.com
2000 Aug 08 3
BCcomponents Product specification
Metal film resistors 5063JD series (space miser)
0.25 to 0.40 W; 1% and 5%
ORDERING INFORMATION
Table 1 Ordering code indicating resistor type and packaging
Note
1. A 0 Ω jumper is available with a maximum resistance Rmax ≤10 mΩ at 3 A.
TY P E TC
(×10−6/K)
TOL .
(%) RESISTANCE RANGE PART NUMBER SPQ
(units)
5063JD ±100
−jumper(1) 5063JD0R000J12AFS 5000; tape & reel
−jumper(1) 5063JD0R000J18AFS 5000; ammopack
±5 0.22 to 0.91 Ω5063JDxxxxxJ12AFS 5000; tape & reel
±5 0.22 to 0.91 Ω5063JDxxxxxJ18AFS 5000; ammopack
±11Ωto 10 MΩ5063JDxxxxxF12AF5 5000; tape & reel
±11Ωto 10 MΩ5063JDxxxxxF18AF5 5000; ammopack
Composition of the clear text code (NAFTA P/N)
•The resistors have an ordering code starting with 50
•The subsequent digits indicate the resistor type,
temperature coefficient, ohmic value, tolerance and
packaging; see Table 1
•The ohmic value is represented by 5-digits; see Table 2
•For temperature coefficient and tolerance, see Table 3.
Table 2 Examples of the ohmic value
Table 3 Letter coding for temperature coefficient and
tolerance
OHMIC
VALUE
5-DIGIT
VALUE
0.22 Ω0R220
1Ω1R000
10 Ω10R00
100 Ω100R0
1k
Ω1K000
10 kΩ10K00
100 kΩ100K0
1M
Ω1M000
TC
(×10−6/K)
LETTER
CODE
TOL.
(%)
LETTER
CODE
100 D ±5J
−−±1F
ORDERING EXAMPLE: CLEAR TEXT CODE
The ordering code of a 5063JD resistor, value 5600 Ω±1%,
taped on a bandolier of 5000 units in tape on reel is:
5063JD5K600F12AF5.
www.DataSheet4U.com
2000 Aug 08 4
BCcomponents Product specification
Metal film resistors 5063JD series (space miser)
0.25 to 0.40 W; 1% and 5%
FUNCTIONAL DESCRIPTION
Product characterization
Standard values of nominal resistance are taken from the
E24 or E96 series for resistors with a tolerance of
±5% or ±1%.
The values of the E24 series are in accordance with
“IEC publication 60063”.
Limiting values
Note
1. The maximum voltage that may be continuously
applied to the resistor element, see
“IEC publication 60115-1”.
DERATING
The power that the resistor can dissipate depends on the
operating temperature; see Figs 1 and 2.
TY P E
LIMITING
VOLTAGE(1)
(V)
LIMITING
POWER
(W)
5063JD 200 0.40
JW35
100 12040 80
T
amb( C)
o
(%P )
rated
0
60
0.2
0.4
155140
Pmax
Fig.1 Derating curve, normal operation.
Fig.2 Derating curve, long term operation.
JW36
100 12040 80
T
amb( C)
o
(%P )
rated
0
60
0.2
0.4
160140
Pmax
NOISE
The current noise is measured in accordance with
“DIN 44049 Part 1 and IEC 600195”. Maximum values are
for 99.8% of all resistors; see Fig 3.
3.0
2.0
0.5
1.0
0.2
0.05
10 k 200 k
R (Ω)
JW39
1 M 20 M
10 M
noise
level
µV
V
Fig.3 Current noise.
www.DataSheet4U.com
2000 Aug 08 5
BCcomponents Product specification
Metal film resistors
5063JD series (space miser)
0.25 to 0.40 W; 1% and 5%
Pulse-load behaviour
Fig.4 Pulse on a regular basis; maximum permissible peak pulse power ( max) as
a function of pulse duration (ti).
P
ˆ
10
6
10
5
10
4
10
3
10
2
10
1
1
JW37
10
3
1
10
10
2
10
1
t (s)
i
Pmax
(W)
^
single pulse
rep. pulse
t /t = 1000
pi
Fig.5 Pulse on a regular basis; maximum permissible peak pulse voltage ( max) as
a function of pulse duration (ti).
V
ˆ
JW38
1200
0
10 610 510 410 310 210 11
800
400
Vmax
(V)
ti(s)
www.DataSheet4U.com
2000 Aug 08 6
BCcomponents Product specification
Metal film resistors
5063JD series (space miser)
0.25 to 0.40 W; 1% and 5%
Definition of symbols (see Figs 4, 5, 6 and 7)
Pulses
The permissible pulse-load is determined by the resistance
change as given for the endurance test after 8000 hours.
PULSE VOLTAGE LIMIT
The maximum permissible impulse voltage is the
voltage pulse short overload depending on the impulse time
ti. High ohmic values are protected by the interdependence
of voltage limit and impulse time. this function is given by
the equation:
Vmax = maximum permissible continuous voltage;
ti = pulse time;
K = 100 s−1.
MAXIMUM PULSE-LOAD
The average load must not exceed the rated dissipation.
For resistance values above the critical resistance the rated
dissipation is given by the resistance value and the limiting
element voltage Vmax:
CONTINUOUS AND SINGLE PULSE-LOAD
There is a difference between repetitive pulse-load
or
single pulse load (e.g. switching events ).
A higher pulse-load Pmax is accepted in the latter case.
SYMBOL DESCRIPTION
applied peak pulse power
maximum permissible peak pulse power;
see Fig.4
applied peak pulse voltage; see Fig 6
maximum permissible peak pulse voltage;
see Fig.5
V(t) pulse voltage
R nominal resistance value
PUrated dissipation at ambient temperature
Rnom nominal resistance value
tipulse duration (rectangular pulses)
tppulse repetition time
P
ˆ
P
ˆmax
Vi
ˆ
V
ˆmax
V
ˆmax
V
ˆmax
2.5 Vmax
⋅
1t
iK⋅+
--------------------------Vmax
+=
P
P1
tpR
---------
=U2
t1
t2
∫t()dt P≤υ
Pti
tp
----P with P power at the pulse time ti =⋅=
P0>
PULSE SHAPES
Figure 6 shows the maximum pulse-load for a rectangular
pulse shape:
Other pulses should be converted into rectangular pulse
shapes (see Fig.7), having the same energy at a given peak
voltage. The following equation shows the calculation for
exponential pulses:
with
PtiV2
ˆ
⋅
tpR⋅
--------------
=
Pτe
2t
p
⋅
------------V2
ˆ
R
------
⋅=τeRC or τe
L
R
----
=
⋅=
Fig.6 Rectangular pulses.
MGA20
6
ti
V
Vi
t
tp
Fig.7 Exponential pulses.
V
t
τ
MGA207
tp
www.DataSheet4U.com
2000 Aug 08 7
BCcomponents Product specification
Metal film resistors
5063JD series (space miser)
0.25 to 0.40 W; 1% and 5%
MECHANICAL DATA
Mass per 100 units
13 g
Marking
The nominal resistance and tolerance are marked on the
resistor using four or five coloured bands in accordance with
IEC publication 60062 “Colour codes for fixed resistors”.
Mounting
The resistors are suitable for processing on automatic
insertion equipment in addition to cutting and bending
machines.The minimum bending is 5 mm (.200 inch).
Outlines
The length of the body (L1) is measured by inserting the leads
into holes of two identical gauge plates and moving these
plates parallel to each other until the resistor body is
clamped without deformation (“IEC publication 60294”).
Fig.8 Outline.
For dimensions see Table 4.
∅D
JW34
L2
L1
∅d
Table 4 Resistor type and physical dimensions; see Fig.8
TYP E
∅D
MAX.
(mm)
L1
MAX.
(mm)
L2
MAX.
(mm)
∅d
(mm)
Dimensions in inches
5063JD 0.063 .142 1.14 .020
Dimensions in millimetres
5063JD 1.6 3.6 29 0.5
www.DataSheet4U.com
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay:
5063JD 13 1%TR 5063JD 178K 1% 5063JD 20 1%TR 5063JD 22 1%TR 5063JD 249 1%TR 5063JD 3.9K 1%TR
5063JD 33 1% 5063JD 432 1%TR 5063JD 470K 1%TR 5063JD 51 1%TR 5063JD 60.4 1%TR 5063JD 619 1%TR
5063JD 69.8K 1% 5063JD 976K 1% 5063JD20K1% 5063JD 143 1% 5063JD 1.74M 1% 5063JD 3.83K 1% 5063JD
237 1%TR 5063JD 820K 1%TR 5063JD 390K 1%TR 5063JD 7.15 1% 5063JD 11 1% 5063JD 22.6 1%TR 5063JD
1.65K 1% 5063JD 16 1%TR 5063JD 560K 1%TR 5063JD 806 1%TR 5063JD 324K 1%TR 5063JD 9.31 1%
5063JD80.6K1% 5063JD 2.8 1% 5063JD 2.43M 1% 5063JD 3.3 1%TR 5063JD 33.2 1% 5063JD 910K 1% 5063JD
4.53 1% 5063JD 665K 1% 5063JD 191 1% 5063JD 2.4K 1%TR 5063JD 51K 1%TR 5063JD 1.3M 1% 5063JD 215K
1% 5063JD 2.55K 1% 5063JD 2.94 1% 5063JD 8.87 1% 5063JD22K1%TR 5063JD 68 1%TR 5063JD 3.24K 1%
5063JD 162 1%TR 5063JD 232K 1% 5063JD 54.9K 1% 5063JD 243K 1%TR 5063JD 196 1% 5063JD 56.2 1%TR
5063JD 2.15K 1% 5063JD 9.76 1% 5063JD 39 1% 5063JD 357K 1%TR 5063JD 5.76K 1% 5063JD 7.68K 1%
5063JD 147 1% 5063JD 130 1%TR 5063JD 205K 1% 5063JD 1.2M 1% 5063JD 127 1%TR 5063JD12K1% 5063JD
866K 1%TR 5063JD 178 1%TR 5063JD121R0FT 5063JD 1.27M 1% 5063JD 232K 1%TR 5063JD 390 1% 5063JD
240 1%TR 5063JD 1.13K 1% 5063JD 523 1%TR 5063JD 2.87K 1% 5063JD 309 1%TR 5063JD2M1%TR 5063JD
249K 1%TR 5063JD 430K 1% 5063JD 9.53 1% 5063JD 261 1%TR 5063JD 976 1%TR 5063JD 5.9K 1% 5063JD
1.05K 1% 5063JD 160K 1%TR 5063JD 200 1%TR 5063JD 6.65 1% 5063JD 402K 1%TR 5063JD 34.8 1% 5063JD
66.5K 1% 5063JD 2.49 1% 5063JD 1.82 1% 5063JD 210K 1%TR 5063JD 143K 1% 5063JD 76.8K 1% 5063JD
2.05K 1% 5063JD 6.98 1% 5063JD 21K 1%TR
