TLP2962
1
Photocouplers GaAℓAs Infrared LED & Photo IC
TLP2962
TLP2962
TLP2962
TLP2962
Start of commercial production
2011-09
1.
1.
1.
1. Applications
Applications
Applications
Applications
• Factory Automation (FA)
• High-Speed Digital Interfacing
• Measurement Instrumentation
2.
2.
2.
2. General
General
General
General
The Toshiba TLP2962 consists of a high-output GaAℓAs light-emitting diode coupled with integrated high gain,
high-speed photodetectors. The TLP2962 guarantees operation at up to 125 and on supplies from 2.7 V to 5.5
V. It is housed in the DIP8 package. The TLP2962 has an internal Faraday shield that provides a guaranteed
common-mode transient immunity of 20 kV/µs.
3.
3.
3.
3. Features
Features
Features
Features
(1) Inverter logic type (open collector output)
(2) Package: DIP8
(3) Operating temperature: -40 to 125
(4) Supply voltage: 2.7 to 5.5 V
(5) Data transfer rate: 15 MBd (typ.) (NRZ)
(6) Threshold input current: 5.0 mA (max)
(7) Supply current: 4 mA (max)
(8) Common-mode transient immunity: ±20 kV/µs (min)
(9) Isolation voltage: 5000 Vrms (min)
(10) Safety standards
UL-approved: UL1577 File No.E67349
cUL-approved: CSA Component Acceptance Service No.5A, File No.E67349
VDE-approved: Option (D4) EN60747-5-5(Note)
Note: When an EN60747-5-5 approved type is needed, please designate the Option (D4).
2014-06-13
Rev.2.0
TLP2962
2
4.
4.
4.
4. Packaging and Pin Configuration
Packaging and Pin Configuration
Packaging and Pin Configuration
Packaging and Pin Configuration
11-10C4S
1: N.C.
2: Anode
3: Cathode
4: N.C.
5: GND
6: VO (Output)
7: N.C.
8: VCC
5.
5.
5.
5. Internal Circuit
Internal Circuit
Internal Circuit
Internal Circuit
Fig.
Fig.
Fig.
Fig. 5.1
5.1
5.1
5.1 Internal Circuit
Internal Circuit
Internal Circuit
Internal Circuit
6.
6.
6.
6. Principle of Operation
Principle of Operation
Principle of Operation
Principle of Operation
6.1.
6.1.
6.1.
6.1. Truth Table
Truth Table
Truth Table
Truth Table
Input
H
L
LED
ON
OFF
Output
L
H
6.2.
6.2.
6.2.
6.2. Mechanical Parameters
Mechanical Parameters
Mechanical Parameters
Mechanical Parameters
Characteristics
Creepage distances
Clearance distances
Internal isolation thickness
7.62-mm Pitch
TLP2962
7.0 (min)
7.0 (min)
0.4 (min)
10.16-mm Pitch
TLP2962F
8.0 (min)
8.0 (min)
0.4 (min)
Unit
mm
2014-06-13
Rev.2.0
TLP2962
3
7.
7.
7.
7. Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
)
)
)
)
LED
Detector
Common
Characteristics
Input forward current
Input forward current derating
Input forward current (pulsed)
Input forward current derating
(pulsed)
Peak transient input forward
current
Peak transient input forward
current derating
Input power dissipation
Input power dissipation
derating
Input reverse voltage
Output current
Output voltage
Supply voltage
Output power dissipation
Output power dissipation
derating
Operating temperature
Storage temperature
Lead soldering temperature
Isolation voltage
(Ta ≥ 116 )
(Ta ≥ 110 )
(Ta ≥ 110 )
(Ta ≥ 110 )
(Ta ≥ 110 )
(10 s)
AC, 60 s, R.H. ≤ 60 %
Symbol
IF
∆IF/∆Ta
IFP
∆IFP/∆Ta
IFPT
∆IFPT/∆Ta
PD
∆PD/∆Ta
VR
IO
VO
VCC
PO
∆PO/∆Ta
Topr
Tstg
Tsol
BVS
Note
(Note 1)
(Note 2)
(Note 3)
Rating
20
-0.6
40
-1.0
1
-25
40
-1.0
5
50
6
6
85
-2.1
-40 to 125
-55 to 150
260
5000
Unit
mA
mA/
mA
mA/
A
mA/
mW
mW/
V
mA
V
mW
mW/
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width (PW) ≤ 1 ms, duty = 50%
Note 2: Pulse width (PW) ≤ 1 µs, 300 pps
Note 3: This device is considered as a two-terminal device: Pins 1, 2, 3 and 4 are shorted together, and pins 5, 6, 7
and 8 are shorted together.
8.
8.
8.
8. Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Characteristics
Input on-state current
Input off-state voltage
Supply voltage
Operating temperature
Symbol
IF(ON)
VF(OFF)
VCC
Topr
Note
(Note 1)
(Note 2)
(Note 2)
Min
6.3
0
2.7
-40
Typ.
3.3/5.0
Max
15
0.8
5.5
125
Unit
mA
V
Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this datasheet should also be considered.
Note: A ceramic capacitor (0.1 µF) should be connected between pin 8 and pin 5 to stabilize the operation of a high-
gain linear amplifier. Otherwise, this photocoupler may not switch properly. The bypass capacitor should be
placed within 1 cm of each pin.
Note 1: The rise and fall times of the input on-current should be less than 0.5 µs.
Note 2: Denotes the operating range, not the recommended operating condition.
2014-06-13
Rev.2.0
TLP2962
4
9.
9.
9.
9. Electrical Characteristics (Note)
Electrical Characteristics (Note)
Electrical Characteristics (Note)
Electrical Characteristics (Note)
(Unless otherwise specified, T
(Unless otherwise specified, T
(Unless otherwise specified, T
(Unless otherwise specified, Ta
a
a
a = -40 to 125
= -40 to 125
= -40 to 125
= -40 to 125
, V
, V
, V
, VCC
CC
CC
CC = 2.7 to 5.5 V)
= 2.7 to 5.5 V)
= 2.7 to 5.5 V)
= 2.7 to 5.5 V)
Characteristics
Input forward voltage
Input forward voltage
temperature coefficient
Input reverse current
Input capacitance
High-level output current
Low-level output voltage
High-level supply current
Low-level supply current
Threshold input current (H/L)
Symbol
VF
∆VF/∆Ta
IR
Ct
IOH
VOL
ICCH
ICCL
IFHL
Note Test
Circuit
Fig.
12.1.1
Fig.
12.1.2
Fig.
12.1.3
Fig.
12.1.4
Test Condition
IF = 10 mA, Ta = 25
IF = 10 mA
VR = 5 V, Ta = 25
V = 0 V, f = 1 MHz, Ta = 25
VF = 0.8 V, VO = 5.5 V,
VCC = 5.5 V
VF = 0.8 V, VO = 5.5 V,
VCC = 5.5 V, Ta = 25
IF = 5 mA
IO = 13 mA (Sinking)
IF = 0 mA
IF = 10 mA
IO = 13 mA (Sinking),
VO < 0.6 V, Ta = 25
IO = 13 mA (Sinking),
VO < 0.6 V
Min
1.45
Typ.
1.55
-2.0
60
0.23
1.6
1.8
1.3
Max
1.7
10
50
10
0.6
4.0
4.0
2.8
5.0
Unit
V
mV/
µA
pF
µA
V
mA
Note: All typical values are at Ta = 25.
10.
10.
10.
10. Isolation Characteristics (Unless otherwise specified, T
Isolation Characteristics (Unless otherwise specified, T
Isolation Characteristics (Unless otherwise specified, T
Isolation Characteristics (Unless otherwise specified, Ta
a
a
a = 25
= 25
= 25
= 25
)
)
)
)
Characteristics
Total capacitance (input to output)
Isolation resistance
Isolation voltage
Symbol
CS
RS
BVS
Note
(Note 1)
(Note 1)
(Note 1)
Test Conditions
VS = 0 V, f = 1 MHz
VS = 500 V, R.H. ≤ 60 %
AC, 60 s
AC, 1 s in oil
DC, 60 s in oil
Min
1×1012
5000
Typ.
1.0
1014
10000
10000
Max
Unit
pF
Ω
Vrms
Vdc
Note 1: This device is considered as a two-terminal device: Pins 1, 2, 3 and 4 are shorted together, and pins 5, 6, 7
and 8 are shorted together.
2014-06-13
Rev.2.0
TLP2962
5
11.
11.
11.
11. Switching Characteristics (Note)
Switching Characteristics (Note)
Switching Characteristics (Note)
Switching Characteristics (Note)
(Unless otherwise specified, T
(Unless otherwise specified, T
(Unless otherwise specified, T
(Unless otherwise specified, Ta
a
a
a = -40 to 125
= -40 to 125
= -40 to 125
= -40 to 125
, V
, V
, V
, VCC
CC
CC
CC = 2.7 to 5.5 V)
= 2.7 to 5.5 V)
= 2.7 to 5.5 V)
= 2.7 to 5.5 V)
Characteristics
Propagation delay time
(H/L)
Propagation delay time
(L/H)
Pulse width distortion
Propagation delay skew
(device to device)
Fall time
Rise time
Common-mode transient
immunity at output high
Common-mode transient
immunity at output low
Symbol
tpHL
tpLH
|tpHL-
tpLH|
tpsk
tf
tr
CMH
CML
Note
(Note 1)
(Note 1)
(Note 1)
(Note 1),
(Note 2)
(Note 1)
(Note 1)
Test
Circuit
Fig.
12.1.5
Fig.
12.1.6
Test Condition
IF = 0→7.5 mA, RL = 350 Ω,
CL = 15 pF
IF = 7.5→0 mA, RL = 350 Ω,
CL = 15 pF
IF = 7.5 mA, RL = 350 Ω,
CL = 15 pF
IF = 0 → 7.5 mA, RL = 350 Ω,
CL = 15 pF
IF = 7.5 → 0 mA, RL = 350 Ω,
CL = 15 pF
VCM = 1000 Vp-p, IF = 0 mA,
VCC = 3.3V / 5 V, Ta = 25
VCM = 1000 Vp-p, IF = 10 mA,
VCC = 3.3V / 5 V, Ta = 25
Min
-40
±20
±20
Typ.
35
25
3
12
±25
±25
Max
75
75
35
40
Unit
ns
kV/µs
Note: All typical values are at Ta = 25.
Note 1: f = 5 MHz, duty = 50%, input current tr = tf = 5 ns, CL is approximately 15 pF which includes probe and stray
wiring capacitance.
Note 2: The propagation delay skew, tpsk, is equal to the magnitude of the worst-case difference in tpHL and/or tpLH
that will be seen between units at the same given conditions (supply voltage, input current, temperature, etc).
2014-06-13
Rev.2.0
TLP2962
6
12.
12.
12.
12. Test Circuits and Characteristics Curves
Test Circuits and Characteristics Curves
Test Circuits and Characteristics Curves
Test Circuits and Characteristics Curves
12.1.
12.1.
12.1.
12.1. Test Circuits
Test Circuits
Test Circuits
Test Circuits
Fig.
Fig.
Fig.
Fig. 12.1.1
12.1.1
12.1.1
12.1.1 I
I
I
IOH
OH
OH
OH Test Circuit
Test Circuit
Test Circuit
Test Circuit Fig.
Fig.
Fig.
Fig. 12.1.2
12.1.2
12.1.2
12.1.2 V
V
V
VOL
OL
OL
OL Test Circuit
Test Circuit
Test Circuit
Test Circuit
Fig.
Fig.
Fig.
Fig. 12.1.3
12.1.3
12.1.3
12.1.3 I
I
I
ICCH
CCH
CCH
CCH Test Circuit
Test Circuit
Test Circuit
Test Circuit Fig.
Fig.
Fig.
Fig. 12.1.4
12.1.4
12.1.4
12.1.4 I
I
I
ICCL
CCL
CCL
CCL Test Circuit
Test Circuit
Test Circuit
Test Circuit
Fig.
Fig.
Fig.
Fig. 12.1.5
12.1.5
12.1.5
12.1.5 Switching Time Test Circuit
Switching Time Test Circuit
Switching Time Test Circuit
Switching Time Test Circuit
Fig.
Fig.
Fig.
Fig. 12.1.6
12.1.6
12.1.6
12.1.6 Common-Mode Transient Immunity
Common-Mode Transient Immunity
Common-Mode Transient Immunity
Common-Mode Transient Immunity
2014-06-13
Rev.2.0
TLP2962
7
12.2.
12.2.
12.2.
12.2. Characteristics Curves (Note)
Characteristics Curves (Note)
Characteristics Curves (Note)
Characteristics Curves (Note)
Fig.
Fig.
Fig.
Fig. 12.2.1
12.2.1
12.2.1
12.2.1 I
I
I
IF
F
F
F - V
- V
- V
- VF
F
F
FFig.
Fig.
Fig.
Fig. 12.2.2
12.2.2
12.2.2
12.2.2 I
I
I
IF
F
F
F - T
- T
- T
- Ta
a
a
a
Fig.
Fig.
Fig.
Fig. 12.2.3
12.2.3
12.2.3
12.2.3 V
V
V
VOL
OL
OL
OL - T
- T
- T
- Ta
a
a
aFig.
Fig.
Fig.
Fig. 12.2.4
12.2.4
12.2.4
12.2.4 V
V
V
VOL
OL
OL
OL - T
- T
- T
- Ta
a
a
a
Fig.
Fig.
Fig.
Fig. 12.2.5
12.2.5
12.2.5
12.2.5 V
V
V
VO
O
O
O - I
- I
- I
- IF
F
F
FFig.
Fig.
Fig.
Fig. 12.2.6
12.2.6
12.2.6
12.2.6 V
V
V
VO
O
O
O - I
- I
- I
- IF
F
F
F
2014-06-13
Rev.2.0
TLP2962
8
Fig.
Fig.
Fig.
Fig. 12.2.7
12.2.7
12.2.7
12.2.7 I
I
I
IFHL
FHL
FHL
FHL - T
- T
- T
- Ta
a
a
aFig.
Fig.
Fig.
Fig. 12.2.8
12.2.8
12.2.8
12.2.8 I
I
I
IFHL
FHL
FHL
FHL - T
- T
- T
- Ta
a
a
a
Fig.
Fig.
Fig.
Fig. 12.2.9
12.2.9
12.2.9
12.2.9 I
I
I
ICCH
CCH
CCH
CCH, I
, I
, I
, ICCL
CCL
CCL
CCL - T
- T
- T
- Ta
a
a
aFig.
Fig.
Fig.
Fig. 12.2.10
12.2.10
12.2.10
12.2.10 I
I
I
ICCH
CCH
CCH
CCH, I
, I
, I
, ICCL
CCL
CCL
CCL - T
- T
- T
- Ta
a
a
a
Fig.
Fig.
Fig.
Fig. 12.2.11
12.2.11
12.2.11
12.2.11 t
t
t
tpHL
pHL
pHL
pHL, t
, t
, t
, tpLH
pLH
pLH
pLH - T
- T
- T
- Ta
a
a
aFig.
Fig.
Fig.
Fig. 12.2.12
12.2.12
12.2.12
12.2.12 |t
|t
|t
|tpHL
pHL
pHL
pHL - t
- t
- t
- tpLH
pLH
pLH
pLH| - T
| - T
| - T
| - Ta
a
a
a
2014-06-13
Rev.2.0
TLP2962
9
Fig.
Fig.
Fig.
Fig. 12.2.13
12.2.13
12.2.13
12.2.13 t
t
t
tpHL
pHL
pHL
pHL, t
, t
, t
, tpLH
pLH
pLH
pLH - T
- T
- T
- Ta
a
a
aFig.
Fig.
Fig.
Fig. 12.2.14
12.2.14
12.2.14
12.2.14 |t
|t
|t
|tpHL
pHL
pHL
pHL - t
- t
- t
- tpLH
pLH
pLH
pLH| - T
| - T
| - T
| - Ta
a
a
a
Fig.
Fig.
Fig.
Fig. 12.2.15
12.2.15
12.2.15
12.2.15 t
t
t
tpHL
pHL
pHL
pHL, t
, t
, t
, tpLH
pLH
pLH
pLH - I
- I
- I
- IF
F
F
FFig.
Fig.
Fig.
Fig. 12.2.16
12.2.16
12.2.16
12.2.16 |t
|t
|t
|tpHL
pHL
pHL
pHL - t
- t
- t
- tpLH
pLH
pLH
pLH| - I
| - I
| - I
| - IF
F
F
F
Fig.
Fig.
Fig.
Fig. 12.2.17
12.2.17
12.2.17
12.2.17 t
t
t
tpHL
pHL
pHL
pHL, t
, t
, t
, tpLH
pLH
pLH
pLH - I
- I
- I
- IF
F
F
FFig.
Fig.
Fig.
Fig. 12.2.18
12.2.18
12.2.18
12.2.18 |t
|t
|t
|tpHL
pHL
pHL
pHL - t
- t
- t
- tpLH
pLH
pLH
pLH| - I
| - I
| - I
| - IF
F
F
F
Note: The above characteristics curves are presented for reference only and not guaranteed by production test,
unless otherwise noted.
2014-06-13
Rev.2.0
TLP2962
10
13.
13.
13.
13. Soldering and Storage
Soldering and Storage
Soldering and Storage
Soldering and Storage
13.1.
13.1.
13.1.
13.1. Precautions for Soldering
Precautions for Soldering
Precautions for Soldering
Precautions for Soldering
The soldering temperature should be controlled as closely as possible to the conditions shown below, irrespective
of whether a soldering iron or a reflow soldering method is used.
• When using soldering reflow (See Fig. 13.1.1 and 13.1.2)
Reflow soldering must be performed once or twice.
The mounting should be completed with the interval from the first to the last mountings being 2 weeks.
Fig.
Fig.
Fig.
Fig. 13.1.1
13.1.1
13.1.1
13.1.1 An example of a temperature profile
An example of a temperature profile
An example of a temperature profile
An example of a temperature profile
when Sn-Pb eutectic solder is used
when Sn-Pb eutectic solder is used
when Sn-Pb eutectic solder is used
when Sn-Pb eutectic solder is used
Fig.
Fig.
Fig.
Fig. 13.1.2
13.1.2
13.1.2
13.1.2 An example of a temperature profile
An example of a temperature profile
An example of a temperature profile
An example of a temperature profile
when lead(Pb)-free solder is used
when lead(Pb)-free solder is used
when lead(Pb)-free solder is used
when lead(Pb)-free solder is used
• When using soldering flow (Applicable to both eutectic solder and Lead(Pb)-Free solder)
Apply preheating of 150 for 60 to 120 seconds.
Mounting condition of 260 within 10 seconds is recommended.
Flow soldering must be performed once.
• When using soldering Iron (Applicable to both eutectic solder and Lead(Pb)-Free solder)
Complete soldering within 10 seconds for lead temperature not exceeding 260 or within 3 seconds not
exceeding 350
Heating by soldering iron must be done only once per lead.
13.2.
13.2.
13.2.
13.2. Precautions for General Storage
Precautions for General Storage
Precautions for General Storage
Precautions for General Storage
• Avoid storage locations where devices may be exposed to moisture or direct sunlight.
• Follow the precautions printed on the packing label of the device for transportation and storage.
• Keep the storage location temperature and humidity within a range of 5 to 35 and 45% to 75%,
respectively.
• Do not store the products in locations with poisonous gases (especially corrosive gases) or in dusty
conditions.
• Store the products in locations with minimal temperature fluctuations. Rapid temperature changes during
storage can cause condensation, resulting in lead oxidation or corrosion, which will deteriorate the
solderability of the leads.
• When restoring devices after removal from their packing, use anti-static containers.
• Do not allow loads to be applied directly to devices while they are in storage.
• If devices have been stored for more than two years under normal storage conditions, it is recommended
that you check the leads for ease of soldering prior to use.
2014-06-13
Rev.2.0
TLP2962
11
14.
14.
14.
14. Marking
Marking
Marking
Marking
Fig.
Fig.
Fig.
Fig. 14.1
14.1
14.1
14.1 Marking
Marking
Marking
Marking
2014-06-13
Rev.2.0
TLP2962
12
Package Dimensions
Package Dimensions
Package Dimensions
Package Dimensions
Unit: mm
Weight: 0.54 g (typ.)
Package Name(s)
TOSHIBA: 11-10C4S
2014-06-13
Rev.2.0
TLP2962
13
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's
written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible
for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which
minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage
to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate
the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA
information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the
precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application
with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications,
including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating
and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample
application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
• PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE").
("UNINTENDED USE").
("UNINTENDED USE").
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation,
equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles,
trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices,
elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
IF YOU USE PRODUCT FOR
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT.
UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales
representative.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any
intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
(2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT,
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or vapor.
Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation,
for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products
(mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and
regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration
Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all
applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
2014-06-13
Rev.2.0
