DS26LS31C,DS26LS31M DS26LS31C/DS26LS31M Quad High Speed Differential Line Driver Literature Number: SNOSBK1B DS26LS31C/DS26LS31M Quad High Speed Differential Line Driver General Description Features The DS26LS31 is a quad differential line driver designed for digital data transmission over balanced lines. The DS26LS31 meets all the requirements of EIA Standard RS422 and Federal Standard 1020. It is designed to provide unipolar differential drive to twisted-pair or parallel-wire transmission lines. n n n n n The circuit provides an enable and disable function common to all four drivers. The DS26LS31 features TRI-STATE (R) outputs and logically ANDed complementary outputs. The inputs are all LS compatible and are all one unit load. n n n n n Output skew -- 2.0 ns typical Input to output delay -- 10 ns typical Operation from single 5V supply Outputs won't load line when VCC = 0V Four line drivers in one package for maximum package density Output short-circuit protection Complementary outputs Meets the requirements of EIA Standard RS-422 Pin compatible with AM26LS31 Available in military and commercial temperature range Logic and Connection Diagrams 00577801 Dual-In-Line Package 00577802 Top View Order Number DS26LS31CM, or DS26LS31CN See NS Package M16A or N16E For Complete Military Product Specifications, refer to the appropriate SMD or MDS. Order Number DS26LS31MJ/883, DS26LS31ME/883 or DS26LS31MW/883 See NS Package E20A, J16A or W16A TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. (c) 2004 National Semiconductor Corporation DS005778 www.national.com DS26LS31C/DS26LS31M Quad High Speed Differential Line Driver June 1998 DS26LS31C/DS26LS31M Absolute Maximum Ratings (Note 2) Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage 7V Input Voltage 7V Output Voltage Molded DIP Package 1476 mW SO Package 1051 mW DS26LS31M 4.5 5.5 V DS26LS31 4.75 5.25 V -55 +125 C 0 +70 C DS26LS31 Maximum Power Dissipation (Note 1) at 25C 1509 mW Units DS26LS31M -0.25 to 6V Cavity Package Max Temperature, TA 5.5V Output Voltage (Power OFF) Min Supply Voltage, VCC Note 1: Derate cavity package 10.1 mW/C above 25C; derate molded DIP package 11.9 mW/C above 25C; derate SO package 8.41 mW/C above 25C. Electrical Characteristics (Notes 3, 4, 5) Symbol Parameter Conditions Min Typ Max Units VOH Output High Voltage IOH = -20 mA VOL Output Low Voltage IOL = 20 mA VIH Input High Voltage VIL Input Low Voltage IIL Input Low Current VIN = 0.4V IIH Input High Current VIN = 2.7V 20 A II Input Reverse Current VIN = 7V 0.1 mA IO TRI-STATE Output Current VO = 2.5V 20 A VO = 0.5V -20 A VCL Input Clamp Voltage ISC Output Short-Circuit Current ICC Power Supply Current 2.5 V 0.5 2.0 V V -40 IIN = -18 mA -30 All Outputs Disabled 0.8 V -200 A -1.5 V -150 mA 60 mA 35 or Active Switching Characteristics VCC = 5V, TA = 25C Typ Max Units tPLH Symbol Input to Output Parameter CL = 30 pF Conditions Min 10 15 ns tPHL Input to Output CL = 30 pF 10 15 ns Skew Output to Output CL = 30 pF 2.0 6.0 ns tLZ Enable to Output CL = 10 pF, S2 Open 15 35 ns tHZ Enable to Output CL = 10 pF, S1 Open 15 25 ns tZL Enable to Output CL = 30 pF, S2 Open 20 30 ns tZH Enable to Output CL = 30 pF, S1 Open 20 30 ns Note 2: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Note 3: Unless otherwise specified min/max limits apply across the -55C to +125C temperature range for the DS726LS31M and across the 0C to +70C range for the DS26LS31. All typicals are given for V CC = 5V and TA = 25C. Note 4: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to ground unless otherwise specified. Note 5: Only one output at a time should be shorted. www.national.com 2 DS26LS31C/DS26LS31M AC Test Circuit and Switching Time Waveforms 00577803 S1 and S2 of load circuit are closed except where shown. FIGURE 1. AC Test Circuit 00577804 f = 1 MHz, tr 15 ns, tf 6 ns FIGURE 2. Propagation Delays 00577805 f = 1 MHz, tr 15 ns, tf 6 ns FIGURE 3. Enable and Disable Times 3 www.national.com DS26LS31C/DS26LS31M Typical Applications Two-Wire Balanced System, RS-422 00577806 Note 6: RT is optional although highly recommended to reduce reflection. Typical Performance Characteristics DS26LS31CN Unloaded IC vs Frequency vs TA DS26LS31 ICC vs VCC vs TA 00577807 00577808 DS26LS31CN VOH vs IOH vs TA DS26LS31CN VOL vs IOL vs TA 00577810 00577809 www.national.com 4 DS26LS31C/DS26LS31M Typical Performance Characteristics (Continued) DS26LS31CN VOD vs IO vs TA 00577811 5 www.national.com DS26LS31C/DS26LS31M Physical Dimensions inches (millimeters) unless otherwise noted Small Outline Package (M) Order Number DS26LS31CM NS Package Number M16A Molded Dual-In-Line Package (N) Order Number DS26LS31CN NS Package Number N16E www.national.com 6 DS26LS31C/DS26LS31M Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16 Lead Ceramic Flatpak (F) Order Number DS26LS31MW/883 NS Package Number W16A 16 Lead Ceramic Dual-in-Line Package (J) Order Number DS26LS31MJ/883 NS Package Number J16A 7 www.national.com DS26LS31C/DS26LS31M Quad High Speed Differential Line Driver Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20 Lead Ceramic Leadless Chip Carrier (E) Order Number DS26LS31MJE/883 NS Package Number E20A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated