General Description
The MAX4400–MAX4403 low-cost, general-purpose op
amps offer Rail-to-Rail®outputs, draw only 320µA of qui-
escent current, and operate from a single +2.5V to +5.5V
supply. For additional power conservation, the MAX4401
offers a low-power shutdown mode that reduces supply
current to 1µA (max) and puts the amplifier’s output in a
high-impedance state. These devices deliver ±1.4mA of
output current and are unity-gain stable with a 1MHz gain-
bandwidth product driving capacitive loads up to 400pF.
The MAX4400–MAX4403 are specified to +125°C, making
them suitable for use in a variety of harsh environments,
such as automotive applications.
The MAX4400 single amplifier is available in ultra-small
5-pin SC70 and space-saving 5-pin SOT23 packages.
The single MAX4401 includes the shutdown feature and is
available in a 6-pin SC70. The MAX4402 is a dual amplifier
available in 8-pin SOT23 and SO packages. The
MAX4403 quad amplifier is packaged in a 14-pin TSSOP
or SO.
Applications
Single-Supply, Zero-Crossing Detectors
Instruments and Terminals
Portable Communications
Electronic Ignition Modules
Infrared Receivers
Sensor Signal Detection
Features
♦Single +2.5V to +5.5V Supply Voltage Range
♦320µA Quiescent Current per Amplifier
♦1µA (max) Shutdown Mode (MAX4401)
♦Available in Space-Saving Packages
5-Pin SC70 (MAX4400)
6-Pin SC70 (MAX4401)
8-Pin SOT23 (MAX4402)
♦110dB AVOL with 2kΩLoad
♦0.015% THD with 2kΩLoad
♦Rail-to-Rail Output Voltage Swing
♦1.4mA of Sink and Source Load Current
♦Unity-Gain Stable up to CLOAD = 400pF
♦Ground-Sensing Inputs
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
________________________________________________________________ Maxim Integrated Products 1
IN+
IN-
1
2
3
5
4OUT
VSS
VDD IN+
IN-
1
2
3
6
5
4OUT
SHDN
VSS
VDD
MAX4400 MAX4401
SC70-5/SOT23-5 SC70-6
19-1599; Rev 3; 8/01
Pin Configurations
Ordering Information
Selector Guide
MAX4401 1Yes
MAX4402 2No
MAX4403 4No
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. Pin Configurations continued at end of data sheet.
No1MAX4400
PART NO. OF AMPLIFIERS
PER PACKAGE
SHUTDOWN
MODE
—
—
AADI
AAB
ADNP
AAG
TOP
MARK
14 TSSOP-40°C to +125°C
MAX4403AUD
8 SO
8 SOT23-8-40°C to +125°C
-40°C to +125°CMAX4402ASA
MAX4402AKA-T
6 SC70-6
5 SOT23-5
5 SC70-5
PIN-
PACKAGE
TEMP RANGE
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
MAX4401AXT-T
MAX4400AUK-T
MAX4400AXK-T
PART
—8 µMAX-40°C to +125°CMAX4402AUA
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
—14 SO-40°C to +125°CMAX4403ASD
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VDD = +5V, VSS = 0, VCM = 0, VOUT = VDD/2, RL=∞connected to VDD/2, SHDN = VDD (MAX4401 only), TA= +25°C, unless
otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Power-Supply Voltage (VDD to VSS) .........................-0.3V to +6V
All Other Pins ...................................(VSS - 0.3V) to (VDD + 0.3V)
Output Short-Circuit Duration
OUT Shorted to VSS or VDD................................... Continuous
Continuous Power Dissipation (TA= +70°C)
5-Pin SC70 (derate 2.5mW/°C above +70°C)............. 200mW
5-Pin SOT23 (derate 7.1mW/°C above +70°C)............571mW
6-Pin SC70 (derate 2.27mW/°C above +70°C)............181mW
8-Pin SOT23 (derate 7.52mW/°C above +70°C)..........602mW
8-Pin µMAX (derate 4.5mW/°C above +70°C) ............ 362mW
8-Pin SO (derate 5.88mW/°C above +70°C)............... 471mW
14-Pin TSSOP (derate 8.33mW/°C above +70°C) ...... 667mW
14-Pin SO (derate 8.33mW/°C above +70°C)............. 667mW
Operating Temperature Range .........................-40°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Slew Rate SR 1V/µs
Gain Margin 20 dB
Phase Margin φM70 degrees
RL= 2kΩ
RL= 100kΩ
RL= 2kΩ
RL= 100kΩ
PARAMETER SYMBOL MIN TYP MAX UNITS
Input Offset Current IOS ±0.1 ±100 pA
Input Bias Current IB±0.1 ±100 pA
Input Offset Voltage VOS
±0.8 ±4.5 mV
Supply Current in Shutdown ISHDN 0.00002 1 µA
Input Resistance RIN 1000 GΩ
Input Common-Mode Voltage
Range VCM VSS VDD - 1.4 V
Common-Mode Rejection Ratio CMRR 68 84 dB
Power-Supply Rejection Ratio PSRR 78 100
Supply Current per Amplifier
Supply Voltage Range VDD 2.5 5.5 V
IDD
320 µA
RL= 2kΩ
RL= 100kΩ
410 700
Large-Signal Voltage Gain AVOL
120 dB
90 110
Output Voltage High VOH
3mV
55 200
Output Voltage Low VOL
2mV
30 75
12 mA
30
Shutdown Mode Output
Leakage IOUTSHDN ±1.0 µA
SHDN Logic Low VIL 0.3 ✕VDD V
SHDN Logic High VIH 0.7 ✕VDD V
SHDN Input Current IIL, IIH ±0.001 ±500 nA
Gain-Bandwidth Product GBW 800 kHz
CONDITIONS
VSS + 0.3V ≤
VOUT ≤VDD - 0.3V
(Note 2)
dB
(Note 2)
MAX4400/MAX4401
SHDN = VSS (Note 1)
Differential or common mode
Inferred from CMRR test
Specified as
|VDD - VOH|
VSS ≤VCM ≤VDD - 1.4V
2.5V ≤VDD ≤5.5V
Specified as
|VSS - VOL|
Sourcing
Inferred from PSRR test
Sinking
VDD = 2.5V
Device in shutdown mode, SHDN = VSS,
VSS < VOUT < VCC (Note 1)
(Note 1)
VDD = 5.0V
(Note 1)
SHDN = VDD or VSS (Note 1)
Output Short-Circuit Current
MAX4402/MAX4403 ±1.0 ±5.5
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
_______________________________________________________________________________________ 3
Total Harmonic Distortion
ELECTRICAL CHARACTERISTICS (continued)
(VDD = +5V, VSS = 0, VCM = 0, VOUT = VDD/2, RL=∞connected to VDD/2, SHDN = VDD (MAX4401 only), TA= +25°C, unless
otherwise noted.)
ELECTRICAL CHARACTERISTICS
(VDD = +5V, VSS = 0, VCM = 0, VOUT = VDD/2, RL=∞connected to VDD/2, TA= -40°C to +125°C, unless otherwise noted.) (Note 3)
Note 1: Shutdown mode is only available in the 6-pin SC70 single op amp (MAX4401).
Note 2: Guaranteed by design.
Note 3: Specifications are 100% tested at TA= +25°C (exceptions noted). All temperature limits are guaranteed by design.
RL= 100kΩ
RL= 2kΩ
CONDITIONS UNITSMIN TYP MAXSYMBOLPARAMETER
VOUT = 2V step
(Note 1)
AV= +1V/V
f = 10kHz, VOUT =
2Vp-p, AV= +1V/V
f = 10kHz
f = 10kHz
(Note 1)
µs
7
tS
Settling Time to 0.1%
0.015 %
0.009
THDTotal Harmonic Distortion
pF
2.5
CIN
Input Capacitance
µs
5
tON
Power-On Time
µs
6
tEN
Enable Delay Time
µs
0.4
tSHDN
Shutdown Delay Time
pF
400
CLOAD
Capacitive-Load Stability
fA/√Hz
1
in
Input Current Noise Density
nV/√Hz
36en
Input Voltage Noise Density
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
V
2.5 5.5
Inferred from PSRR testVDD
Supply Voltage Range
Supply Current per Amplifier IDD 800 µA
mV
±6.5
±8.0
MAX4400/MAX4401
MAX4402/MAX4403
VOS
Input Offset Voltage
Input Offset Voltage Drift TCVOS ±1 µV/°C
pA
±100
(Note 2)IB
Input Bias Current
Input Offset Current IOS (Note 2) ±100 pA
V
VSS VDD - 1.5
Inferred from CMRR testVCM
Input Common-Mode Voltage
Range
Common-Mode Rejection Ratio CMRR VSS ≤VCM ≤VDD - 1.5V 65 dB
dB
74
2.5V ≤VCC ≤5.5VPSRRPower-Supply Rejection Ratio
Shutdown Mode Output
Leakage IOUTSHDN
Device in shutdown
mode, SHDN = VSS,
VSS < VOUT < VDD
(Note 1)
±1.0
±5.0
µA
V
0.3 ✕VDD
(Note 1)VIL
SHDN Logic Low
SHDN Logic High VIH (Note 1) 0.7 ✕VDD V
nA
±1000
SHDN = VDD or VSS (Notes 1, 2)
IIL, IIH
SHDN Input Current
Large-Signal Voltage Gain AVOL VSS + 0.3V ≤VOUT ≤VDD - 0.3V, RL= 2kΩ85 dB
mV
250
mV
100
Specified as |VDD - VOH|, RL= 2kΩ
Specified as |VSS - VOL|, RL = 2kΩ
VOH
VOL
Output Voltage High
Output Voltage Low
VSS ≤VCM ≤VDD - 1.0V TA= -20°C to +125°C 50
TA= -40°C to +85°C
TA= +85°C to +125°C
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
4 _______________________________________________________________________________________
Typical Operating Characteristics
(VDD = +5V, VSS = 0, VCM = VDD/2, VSHDN = 5V, RL=∞connected to VDD/2, TA= +25°C, unless otherwise noted.)
80
60
40
20
0
-20
-40
-60
-80
-100
-120
-140
-160
-180
1 10 1k 10M1M
GAIN AND PHASE
vs. FREQUENCY (NO LOAD)
MAX4400 toc01
FREQUENCY (Hz)
GAIN (dB)/PHASE (degrees)
100 10k 100k
AVCL = +1000V/V
80
60
40
20
0
-20
-40
-60
-80
-100
-120
-140
-160
-180
1 10 1k 10M1M
GAIN AND PHASE
vs. FREQUENCY (CL = 400pF)
MAX4400 toc02
FREQUENCY (Hz)
GAIN (dB)/PHASE (degrees)
100 10k 100k
AVCL = +1000V/V
10 1k100 10k 100k 1M
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
MAX4400 toc03
FREQUENCY (Hz)
PSRR (dB)
10
-110
-90
-10
-30
-50
-70
FREQUENCY (Hz)
1000
0.001
10 100 1k 10k 100k 1M
OUTPUT IMPEDANCE
vs. FREQUENCY
0.1
MAX4400 toc4
OUTPUT IMPEDANCE (Ω)
10
0.01
1
100
300
350
400
450
500
-40 0 40 80-20 20 60 100 120
SUPPLY CURRENT vs. TEMPERATURE
MAX4400 toc05
TEMPERATURE (°C)
SUPPLY CURRENT (µA)
1
10
100
1k
10k
100k
-40 0 40 80-20 20 60 100 120
MAX4401
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
MAX4400 toc06
TEMPERATURE (°C)
SUPPLY CURRENT (pA)
VSHDN = VSS
0.1
10
1k
1M
-40 0 40 80-20 20 60 100 120
MAX4401
OUTPUT LEAKAGE CURRENT
vs. TEMPERATURE
MAX4400 toc07
TEMPERATURE (°C)
ILEAK (pA)
VSHDN = VSS
VOUT = VDD/2
-1500
-1000
-500
500
0
1000
1500
-40 0 40 80-20 20 60 100 120
INPUT OFFSET VOLTAGE
vs. TEMPERATURE
MAX4400 toc08
TEMPERATURE (°C)
VOS (µV)
30
20
10
0
50
40
70
60
-40 0 40 80-20 20 60 100 120
OUTPUT VOLTAGE SWING HIGH
vs. TEMPERATURE
MAX4400 toc09
TEMPERATURE (°C)
VDD - VOH (mV)
RL = 2kΩ to VDD/2
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
_______________________________________________________________________________________ 5
Typical Operating Characteristics (continued)
(VDD = +5V, VSS = 0, VCM = VDD/2, VSHDN = 5V, RL=∞connected to VDD/2, TA= +25°C, unless otherwise noted.)
0
10
20
30
40
50
-40 0 40 80-20 20 60 100 120
OUTPUT VOLTAGE SWING LOW
vs. TEMPERATURE
MAX4400 toc10
TEMPERATURE (°C)
VOL - VEE (mV)
RL = 2kΩ to VDD/2
-100
-90
-80
-70
-60
-40 0 40 80-20 20 60 100 120
COMMON-MODE REJECTION RATIO
vs. TEMPERATURE
MAX4400 toc11
TEMPERATURE (°C)
CMRR (dB)
0
40
80
60
20
100
120
140
0.5 1.5 2.5 3.51.0 2.0 3.0 4.0 4.5
LARGE-SIGNAL GAIN
vs. OUTPUT VOLTAGE
MAX4400 toc12
VOUT (V)
GAIN (dB)
RL = 2kΩ
100
115
110
105
120
130
125
140
135
-40 0 40 80-20 20 60 100 120
LARGE-SIGNAL GAIN
vs. TEMPERATURE
MAX4400 toc13
TEMPERATURE (°C)
GAIN (dB)
RL = 2kΩ
1.0
1.5
2.0
2.5
3.0
-40 0 40 80-20 20 60 100 120
MINIMUM OPERATING VOLTAGE
vs. TEMPERATURE
MAX4400 toc14
TEMPERATURE (°C)
VMIN (V)
10 1k100 10k 100k
TOTAL HARMONIC DISTORTION
vs. FREQUENCY
MAX4400 toc15
FREQUENCY (Hz)
THD (%)
0.1
0.01
0.0001
0.001
RL = 2kΩ
VOUT = 2Vp-p
AV = +1
0.0001
0.001
0.1
0.01
1
10
0 1.00.5 1.5 2.0 2.5 3.0
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. INPUT AMPLITUDE
MAX4400 toc17
VIN (Vp-p)
THD + N (%)
RL = 2kΩ
f = 10kHz
BW = 20kHz
0.0001
0.001
0.1
0.01
1
10
0 1.00.5 1.5 2.0 2.5 3.0
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. INPUT AMPLITUDE
MAX4400 toc18
VIN (Vp-p)
THD + N (%)
RL = 100kΩ
f = 10kHz
BW = 20kHz
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
6 _______________________________________________________________________________________
Typical Operating Characteristics (continued)
(VDD = +5V, VSS = 0, VCM = VDD/2, VSHDN = 5V, RL=∞connected to VDD/2, TA= +25°C, unless otherwise noted.)
CAPACITIVE-LOAD STABILITY
2000
0
1k 10k 100k
500
MAX4400 toc19
RESISTIVE LOAD (Ω)
CAPACITIVE LOAD (pF)
1000
1500
AV = +1
TA = +25°C
UNSTABLE
REGION
STABLE
REGION
2µs/div
IN
50mV/div
OUT
NONINVERTING SMALL-SIGNAL
TRANSIENT RESPONSE
MAX4400 toc20
AV = +1V/V
RL = 2kΩ
10µs/div
IN
2V/div
OUT
NONINVERTING LARGE-SIGNAL
TRANSIENT RESPONSE
MAX4400 toc21
AV = +1V/V
RL = 2kΩ
0
10
5
20
15
25
30
0 200 300100 400 500 600
PERCENT OVERSHOOT
vs. CAPACITIVE LOAD
MAX4400 toc22
CLOAD (pF)
OVERSHOOT (%)
NEGATIVE OVERSHOOT
POSITIVE OVERSHOOT
MAX4402/MAX4403
CHANNEL-TO-CHANNEL ISOLATION
vs. FREQUENCY
MAX4400 toc25
130
50
0.01 1100 1000
60
FREQUENCY (kHz)
CHANNEL-TO-CHANNEL ISOLATION (dB)
80
70
100
110
90
120
0.1 10
0
100
50
250
200
150
400
350
300
450
021 3456
SUPPLY CURRENT vs. SUPPLY VOLTAGE
MAX4400 toc24
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (µA)
VOUT = VDD/2
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
_______________________________________________________________________________________ 7
FUNCTION
— — Noninverting Amplifier Input A
— — Noninverting Amplifier Input B
— — Noninverting Amplifier Input C
— — Noninverting Amplifier Input D
— — Inverting Amplifier Input B
— — Inverting Amplifier Input A
3 3 Inverting Amplifier Input
2 2 Negative Supply. Connect to ground for single-
supply operation
— — Amplifier Output B
— — Amplifier Output A
4 4 Amplifier Output
— — Inverting Amplifier Input D
— — Inverting Amplifier Input C
Pin Description
— 5 Active-Low Shutdown Input. Connect to VDD for
normal operation. Do not leave floating.
5 6 Positive Supply
— — Amplifier Output D
— — Amplifier Output C
3
5
—
—
6
2
—
4
7
1
—
—
—
—
8
—
—
PIN
3
5
10
12
6
2
—
11
7
1
—
13
9
—
4
14
8
NAME
INA+
INB+
INC+
IND+
INB-
INA-
IN-
VSS
OUTB
OUTA
OUT
IND-
INC-
SHDN
VDD
OUTD
OUTC
1Noninverting Amplifier Input1 — — IN+
MAX4401MAX4400 MAX4402 MAX4403
Detailed Description
Rail-to-Rail Output Stage
The MAX4400–MAX4403 can drive a 2kΩload and still
typically swing within 55mV of the supply rails. Figure 1
shows the output voltage swing of the MAX4400 config-
ured with AV = +10V/V.
Driving Capacitive Loads
Driving a capacitive load can cause instability in many
op amps, especially those with low quiescent current.
The MAX4400–MAX4403 are unity-gain stable for a
range of capacitive loads to above 400pF. Figure 2
shows the response of the MAX4400 with an excessive
capacitive load. Adding a series resistor between the
output and the load capacitor (Figure 3) improves the
1V/div
100µs/div
Figure 1. Rail-to-Rail Output Operation
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
8 _______________________________________________________________________________________
circuit’s response by isolating the load capacitance
from the op amp’s output.
Applications Information
Shutdown Mode
The MAX4401 features a low-power shutdown mode.
When SHDN goes low, the supply current drops to
20pA (typ) and the output enters a high-impedance
state. Pull SHDN high to enable the amplifier. Do not
leave SHDN floating. Figure 4 shows the shutdown
waveform.
Power-Up
The MAX4400–MAX4403 outputs typically settle within
5µs after power-up. Figure 5 shows the output voltage
on power-up and power-down.
Power Supplies and Layout
The MAX4400–MAX4403 operate from a single +2.5V
to +5.5V power supply. Bypass the power supply with a
0.1µF capacitor to ground.
Good layout techniques optimize performance by
decreasing the amount of stray capacitance at the op
amp’s inputs and outputs. To decrease stray capaci-
tance, minimize trace lengths by placing external com-
ponents close to the op amp’s pins.
2µs/div
IN
50mV/div
OUT
RISO
CL
MAX4400
MAX4401
MAX4402
MAX4403
Figure 3. Capacitive-Load-Driving Circuit
R
L
= 10MΩ TO GND
C
L
= 25pF
400µs/div
SHDN
2V/div
OUT
Figure 4. Shutdown Waveform
10µs/div
OUT
1V/div
VDD
2V/div
Figure 5. Power-Up/Power-Down Waveform
Figure 2. Small-Signal Transient Response with Excessive
Capacitive Load
MAX4400/MAX4401 TRANSISTOR COUNT: 101
MAX4402 TRANSISTOR COUNT: 202
MAX4403 TRANSISTOR COUNT: 404
Chip Information
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
_______________________________________________________________________________________ 9
Package Information
SC70, 5L.EPS
6
SOT23-8/SO/µMAX
TSSOP/SO
VSS
OUTA
INA+
1
2
3
4
8
INB-
5INB+
7OUTB
INA-
VDD
OUTA
INA+
INB+
OUTB
INB-
1
2
3
4
5
6
7
14
13
12
11
10
9
8
IND+
INC+
INC-
OUTC
IND-
OUTD
INA-
VDD VSS
MAX4403
MAX4402
Pin Configurations (continued)
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
10 ______________________________________________________________________________________
SC70, 6L.EPS
Package Information (continued)
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
______________________________________________________________________________________ 11
Package Information (continued)
SOT5L.EPS
MAX4400–MAX4403
Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2001 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
Package Information (continued)
SOT23, 8L.EPS
ENGLISH • ???? • ??? • ???
WHAT'S NEW
PRODUCTS
SOLUTIONS
DESIGN
APPNOTES
SUPPORT
BUY
COMPANY
MEMBERS
MAX4402
Part Number Table
Notes:
See the MAX4402 QuickView Data Sheet for further information on this product family or download the
MAX4402 full data sheet (PDF, 384kB).
1.
Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.2.
Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within
one business day.
3.
Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full
data sheet or Part Naming Conventions.
4.
* Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the
product uses.
5.
Part Number
Free
Sample
Buy
Direct
Package:
TYPE PINS SIZE
DRAWING CODE/VAR *
Temp
RoHS/Lead-Free?
Materials Analysis
MAX4402ASA
SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-40C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX4402ASA-T
SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-40C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX4402ASA+T
SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-40C to +125C
RoHS/Lead-Free: Yes
Materials Analysis
MAX4402ASA+
SOIC;8 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-40C to +125C
RoHS/Lead-Free: Yes
Materials Analysis
MAX4402AKA
SOT-23;8 pin;
Dwg: 21-0078F (PDF)
Use pkgcode/variation: K8-5*
-40C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX4402AKA+
SOT-23;8 pin;
Dwg: 21-0078F (PDF)
Use pkgcode/variation: K8+5*
-40C to +125C
RoHS/Lead-Free: Yes
Materials Analysis
MAX4402AKA+T
SOT-23;8 pin;
Dwg: 21-0078F (PDF)
Use pkgcode/variation: K8+5*
-40C to +125C
RoHS/Lead-Free: Yes
Materials Analysis
MAX4402AKA-T
SOT-23;8 pin;
Dwg: 21-0078F (PDF)
Use pkgcode/variation: K8-5*
-40C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX4402AUA+
uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-40C to +125C
RoHS/Lead-Free: Yes
Materials Analysis
MAX4402AUA-T
uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8-1*
-40C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX4402AUA
uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8-1*
-40C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX4402AUA+T
uMAX;8 pin;3 x 3mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
-40C to +125C
RoHS/Lead-Free: Yes
Materials Analysis
Didn't Find What You Need?
CONTACT US: SEND US AN EMAIL
C opyright 2007 by M axim I ntegrated P roduc ts, Dallas Semiconduc tor • Legal Notices • Privacy P olicy