PD70210 Evaluation Board - U se r G u id e PD70210EVB PD70210 HDBT level PD Evaluation Board User Guide Revision 1.0 PRODUCTION DATA - Information contained in this document is proprietary to Microsemi and is current as of publication date. This document may not be modified in any way without the express written consent of Microsemi. Product processing does not necessarily include testing of all parameters. Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. PD70210 Evaluation Board - U se r G u id e Table of Contents 1 ABOUT THIS GUIDE ........................................................................................................................................3 1.1 Audience ..................................................................................................................................................3 1.2 Organization .............................................................................................................................................3 1.3 Reference Documents .............................................................................................................................3 2 INTRODUCTION ...............................................................................................................................................4 2.1 Evaluation Boards Ordering Information ..................................................................................................5 2.2 Evaluation Board Features ......................................................................................................................5 3 PHYSICAL DESCRIPTION .................................................................................................................................6 3.1 Physical Characteristics ...........................................................................................................................6 3.2 Package Contents ....................................................................................................................................6 3.3 Connectors ...............................................................................................................................................6 3.4 Indications ................................................................................................................................................8 4 ELECTRICAL CHARACTERISTICS .....................................................................................................................8 5 INSTALLATION ................................................................................................................................................9 5.1 Preliminary Considerations and Safety Precautions ................................................................................9 5.2 Initial Configuration ..................................................................................................................................9 6 SCHEMATIC..................................................................................................................................................10 7 LIST OF M ATERIALS .....................................................................................................................................12 8 BOARD LAYOUT ...........................................................................................................................................14 Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 2 PD70210 Evaluation Board - U se r G u id e 1 About this Guide This user guide provides both description and operation procedures for Microsemi's PD70210 evaluation board. This board type is used for evaluating the performance of PD70210 device. PD70210ILD device supports both HDBT standard or standard IEEE802.3at PD application interface. The board supports a 95 Watt output at the received voltage level. 1.1 Audience This user guide is intended for qualified personnel, that is, operators and technicians who have a background in basic concepts of electronics. 1.2 Organization This guide is arranged according to the following: Chapter 2 About this Guide: Describes the objectives, audience, and organization. Chapter 2 Introduction: Provides an overview about evaluation board's main functions, features, physical characteristics and ordering information. Chapter 3 Physical Description: Provides explanation related to the physical description (switches, jumpers, connectors). Chapter 4 Electrical Characteristics: Provides electrical characteristics of the evaluation board. Chapter 5 Installation: Provides a description of the installation process. Chapter 6 Schematic: Provides a board schematic diagram. Chapter 7 List of Materials: Provides the board's list of materials. Chapter 8 Board Layout: Provides board Gerber files description for all layers. 1.3 Reference Documents PD70210 datasheet, catalog number DS_PD70210_PD70210A Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 3 PD70210 Evaluation Board - U se r G u id e 2 Introduction Microsemi's PD70210ILD device is part of a family of devices which are targeted for realizing the HDBT or multi 802.3at standard PD interface. The PD interface family of devices includes the following: Device type Power Capability Integrates PWM Controller PD70210ILD Twin HDBT ports No PD70210AILD Twin HDBT ports supporting Wall adapter connection No PD70211ILQ Twin HDBT ports supporting Wall adapter connection Yes Microsemi's PD70210 Evaluation Board (see Figure 2) provides designers with the environment needed for evaluating the performance and implementation of PD applications based on PD70210 device. The board uses a single PD device, PD70210ILD, to support the Detection, Class, and Power Supplying phases on the 2/4 Pairs of the Cat5 cable. PD70210ILD supports a standard Twin HDBT interface and compatible to IEEE802.3AT Type 2 interface. All necessary steps and connection instructions required to install and operate this board are provided within this document. RJ Data out Vin RJ45 Data + Power Pulse XFMR Active Mosfet Bridge PD70210 Based Interface Vout conn Wall adapter In Figure 1: PD70210EVB Block Diagram Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 4 PD70210 Evaluation Board - U se r G u id e Figure 2: PD70210 Evaluation Board - General View 2.1 Evaluation Boards Ordering Information Microsemi's supplies the following Evaluation Boards: 2.2 Ordering Number Description PD70210EVB IEEE802.3AT Type 2 PD, based on PD70210 device, Evaluation Board Features Designed to support Data and Spare current by a single PD70210 device Input RJ45 connectors (Data and Power In) Output voltage connector. On board PSE type LED indicators Evaluation Board working temperature: 0 to +70C RoHS compliant Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 5 PD70210 Evaluation Board - U se r G u id e 3 Physical Description 3.1 Physical Characteristics The following Table 1 lists the evaluation board's physical characteristics. Table 1: Physical Characteristics Parameter Value Mechanical dimensions in mm 3.2 134 x 45 x 19mm (L x W x H) Package Contents Upon opening the Evaluation Board package, verify the following part is included; If it seems damaged, contact local representative or Microsemi's headquarters. Package content for standard shipments is: PD70210 Evaluation Board 3.3 Connectors The following sections provide both general and detailed information regarding unit's connectors. 3.3.1 Connectors Table Table 2 lists the Evaluation Board's connectors. Table 2: Connectors List # Connector 1 J1 RJ45 Connector RJ45 port for Data and Power In for PSE connection 2 J5 PD device Output Terminal blocks for connecting a load to output. 3 J4,J6 PD device Output Banana Jacks for connecting a load to output. Name Description 3.3.2 Connectors Detailed Explanation The numbering is in reference to the numbers listed in Table 2. 1. RJ45 Connector There is a Data+Power dedicated RJ45 connector, See Figure 3. Table 3: RJ45 Connectors CON1 Pin No Signal Name Description 1, 2 Data and Power In Data and power input to powered device (HDBT Master Negative data port) 3, 6 Data and Power In Data and power input to powered device (HDBT Master Positive data port) 4, 5 Data and Power In Data and power input to powered device (HDBT Master Positive data port) 7, 8 Data and Power In Data and power input to powered device (HDBT Master Negative data port) Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 6 PD70210 Evaluation Board - U se r G u id e Figure 3: Front RJ45 Connector 2. Vout Connectors See Figure 4. J5 -output connection, used for connecting to external load. For easy connection, Black and Red Banana jacks are parallel to J5 connections. Table 4: J5 Connector (Green) Pin No. Signal Name Description J5 (Left)- Pin 1 Vout_Rtn Return PD received output voltage J5 (Right)-Pin 2 Vout Positive PD received output voltage Figure 4: Vout Connectors Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 7 PD70210 Evaluation Board - U se r G u id e 3.4 Indications The following sections provide general information regarding unit indications. 3.4.1.1 LED Indication See Figure 5. D14 is the Power_GOOD indication LED, a PD70210 device output signal indicating the device isolation switch is operated. In all operating state this flag is lit. D12 is the AT_FLAG indication LED, a PD70210 device output signal indicating the device has detected a 2 finger class event from the PSE side in the class stage. The flag will be operative at 3, 4, and 6 fingers detection as well. D10 is the 4P_AT indication LED, a PD70210 device output signal indicating the device has detected a 4 finger class event from the PSE side in the class stage, or a 2 finger class event from the PSE side in the class stage, and SUPP_Sa and SUPP_Sb are both High. The flag will be operative at 6 fingers detection as well. D11 is the HD_FLAG indication LED, a PD70210 device output signal indicating the device has detected a 3 finger class event from the PSE side in the class stage. The flag will be operative at 6 fingers detection as well. D9 is the 4P_HD indication LED, a PD70210 device output signal indicating the device has detected a 6 finger class event from the PSE side in the class stage. Figure 5: LED Indications 4 Electrical Characteristics Evaluation board's electrical characteristics are described below: Table 5: Electrical Characteristics Parameter Min Max RJ45 connector 38 57 Maximum Available Current 2.2 V A Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 8 PD70210 Evaluation Board - U se r G u id e 5 Installation 5.1 Preliminary Considerations and Safety Precautions Verify board's power supply is turned off before all peripheral devices are connected. Note: In maximum power at the output, some of the devices may reach high temperatures (still less than 70 degrees). Pay attention while testing these devices. 5.2 Initial Configuration Note: Prior to starting any operation, it is important to verify that the Evaluation Board is setup as shown in Figure 6. 1. Connect load to main board (J5), while it is turned Off. Notice: To comply with IEEE802.3AT standard, the load should be set only after the PSE is On. The indication for PSE On is PGOOD led lit. 2. Connect a Cat5 cable from PSE to Evaluation Board (J1). 3. Turn On the Load. Electronic Load Power Cable DC output PSE Data + Power input Cat5 cable Cat5 cable Figure 6: Test Setup Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 9 PD70210 Evaluation Board - U se r G u id e 6 Schematic Power_Data+ 2 3 SUPP_S1 Power_Data- 1 BAV70 D55 PD-SOT23 Power_sapre+2 3 SUPP_S2 Power_sapre-1 BAV70 D56 PD-SOT23 RCLASS R119 20K PD-0603 R2 60.4K PD-0603 PD-0603 R1 30.9 PD-0603 VPP RDET SUPP_S1 SUPP_S2 RREF RCLS VPN_IN7 VPN_IN8 VAUX PGOOD 4P_HD_FLAG 4P_AT_FLAG HD_FALG AT_FLAG VPN_OUT10 VPN_OUT9 16 15 14 13 12 11 10 9 C6 + 22uF 100V ALU D8H12F3_5 N.C N.C 10 VPNin_BR 1 Power_Data- PD-1206 20K R75 C3 100nF 100v tp135x70 VPNout HK-2-G-S05 PD-70210 PD-DFN-16-5X4-15-v ia VPNin HK-2-G-S05 tp135x70 C7 22uF 100V ALU D8H12F3_5 N.C C2 1uF Power_Data10 VPNin SW1 3 4 2 1 78F01S SW-4P VPNout Power_Data+ PD-0805 R136 0 VPNin Power_sapre- PD-0805 RJ45-I R137 0 N.C Power_sapre+ Power_sapre+ 23 24 22 20 21 19 17 18 16 14 15 13 PD-0805 VPP PD-SOT23 R121 20K PD-0603 PD-SOD323 PD-SOT23 C85 1nF PD-1206-W PD-1206 20K R72 PD-1206-W PD-1206 20K R73 PD-1206-W PD-1206 20K R74 ~ 2 Q8 FMMT549 D14 Super Y ellow Green N.C D9 Super Y ellow Green D10 Super Y ellow Green 2 1 2 + 2 4 2 3 2 1 PD-1206-W PD-1206 20K R71 PD-SOD323 PD-SOT23 R123 20K PD-0603 PD-Mosf et_Dual C87 1nF DFS-BRIDGE D11 Super Y ellow Green D12 Super Y ellow Green PGOOD 1 PGOOD 4P_HD_FLAG 1 4P_HD 4P_AT_FLAG 1 4P_AT HD_FLAG 1 PD-SOT23 PD-MLP12-4_5X5 PD-SOT23 2 D54 2 PD-SOD323 3 1 ~ D52 N.C VPP 1 1 1 VPP 1 $PIN11 3 2 D7 SDB203 1 $PIN5 $PIN9 $PIN10 BAV21WS PD-SOT23 4 PD-1206-W PD-1206 20K R76 Q21 3 $PIN3 $PIN4 2 $PIN8 D51 PD-0603 1 1 1 12 $PIN6 $PIN7 $PIN2 VPP 3 2 BAV21WS 10 11 $PIN0 $PIN1 6 5 2 9 $PIN13 $PIN12 PD-SOT23 PD-SOD323 BZX84C8V2 LT1G D50 D49 1 2 1 3 1 14 13 7 8 2 BZX84C8V2 LT1G D53 3 1 2 U17 3 $PIN15 $PIN14 D48 16 15 1 2 3 10 9 Q9 FMMT549 3 8 7 6 5 4 3 2 1 BAV21WS PD-SOT23 2 N.C 2 VPP R122 20K PD-0603 C86 1nF PD-0603 D47 1 1 2 2 1 3 5 4 6 8 7 9 11 10 12 BEL-S558-10GB-02V C84 1nF - R120 20K PD-0603 Q20 MMBT2222ALT1 J7 R138 0 N.C VPP T1 VP6014 LF 1 HD_FLAG AT_FLAG 1 AT_FLAG PD-0603 5558397-1 rj45-5 PD-0603 Power_sapre- VPNin_BR N.C Figure 7: Board Schematics (1 of 2) Copyright (c) 2013 Rev. 1.0 09-Oct-13 2 1 1 VAUX PGOOD 4P_HD_FLAG 4P_AT_FLAG HD_FLAG AT_FLAG + C1 100nF 100v Microsemi Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 10 1 C83 PD-SOT23 1nF PD-MLP12-4_5X5 1 2 3 4 5 6 7 8 RDET SUPP_S1 SUPP_S2 RREF VAUX 4 3 2 N.C FMMT549 DFS-BRIDGE PD-0603 J5 U1 PD-SOT23 PD-SOD323 PD-Mosf et_Dual 1 1 ~ R3 24.9K PD-0603 2 BAV21WS Q5 1 1 1 2 4 3 D46 3 1 2 1 D45 C4 100n 100V D3 NC N.C 1 2 1 2 3 2 2 1 + 2 $PIN11 3 2 D6 SDB203 1 $PIN5 4 4 Trm_P PD-SOT23 PD-SOD323 PD-SOT23 C81 R117 1nF 20K PD-0603 IN4 IN3 IN2 IN1 $PIN3 $PIN4 $PIN13 $PIN12 12 $PIN15 $PIN14 BAV21WS 14 13 IN8 IN7 IN6 IN5 16 15 8 7 6 5 4 3 2 1 2 9 $PIN9 $PIN10 R124 20K PD-0603 PD-SOT23 PD-SOD323 PD-SOT23 LT1G BZX84C8V2 17 $PIN8 Q19 MMBT2222ALT1 ~ $PIN2 2 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 3 9 10 11 BAV21WS 3 PD-SOT23 PD-SOT23 PD-SOD323 FMMT549 BZX84C8V2 LT1G D42 D41 1 2 1 3 1 Q10 SS71800-007F 6 5 VPP 2 9 $PIN6 $PIN7 3 J1 $PIN0 $PIN1 2 7 8 2 3 MMBT2222ALT1 BAV21WS BZX84C8V2 LT1G PD-0603 D43 D44 3 1 2 1 1 U16 2 1 2 1 1 - PD-0603 BZX84C8V2 LT1G D40 3 D39 Q18 POWER + DATA INPUT VPP R118 20K PD-0603 C82 1nF C80 1nF 1 VPP R116 20K PD-0603 J4 CON-F602-2P 571-0500 VPP HK-2-G-S05tp135x70 2 Power_Data+ J6 CON-F602-2P 571-0100 PD70210 Evaluation Board - U se r G u id e Power_DataPower_Data+ Power_saprePower_sapre+ SWITCHCRAFT-RAPC722 RAPC722X-TB13 N.C 1 3 2 D13 2 PD-SMA C37 10n 100V X7R PD-0805 VPP 1 R139 75 PD-0805 C35 10n 100V X7R PD-0805 R140 75 PD-0805 C38 10n 100V X7R PD-0805 R141 75 PD-0805 C36 10n 100V X7R PD-0805 R142 75 PD-0805 100v J2 VPNin C88 1n 2000V X7R 0 0 R79 R78 C5 100nF N.C VPNin_BR N.C CVILUX-CH82-10P-V AT_FLAG PD-1206 9 7 5 3 1 9 10 7 8 5 6 3 4 1 2 10 8 6 4 2 VAUX PGOOD 4P_HD_FLAG 4P_AT_FLAG HD_FLAG JP11 PD-1206 VPNout VPNin_BR VPNin IN2 IN6 IN5 R129 0 PD-0402 Power_Data- R128 0 PD-0402 IN1 R131 0 PD-0402 Power_Data+ R130 0 PD-0402 IN3 IN8 R133 0 PD-0402 R135 0 PD-0402 Power_sapre- Power_sapre+ R132 0 PD-0402 R134 0 PD-0402 IN4 IN7 Figure 8: Board Schematics (2 of 2) Copyright (c) 2013 Rev. 1.0 09-Oct-13 Microsemi Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 11 PD70210 Evaluation Board - U se r G u id e 7 List of Materials Table 6: PD70210EVB Components Item Description Qty Ref Des Mfr Manufacturer P\N 1 HDbaseT, AF/AT PD CHIP Front End 1 U1 Microsemi PD70210ILD 2 CAP CRM 10nF 100V 5% X7R 0805 SMT 4 C35-C38 AVX 08051C103JAT2A 3 CAP CRM 1nF/2000V 10%++X7R 1206 SMT 1 C88 AVX 1206GC102KAT1A 4 CAP CRM 100nF 100V 10% X7R 1206 SMT 1 C4 AVX 12061C104KAT2A 5 Cap 1nF 100V 10% X7R 0603 SMT 8 C80-C87 Hitano 0603B102K101NT 6 Capacitor,X7R, 1uF, 25V, 10% 06 03 1 C2 Murata GRM188R71E105 KA12D 7 Capacitor, X7R, 100nF,100v, 10% 0603 1 C1 Murata GRM188R72A104 KA35D 8 PIN HEADER 2*5 PINs SMT 0.1" PIN SQUER TIN 1 JP11 CviLux CH81-102M100-00 9 CON RJ45 SINGLE 8 POS. SHILD ED 1 J1 Bel Stewart SS71800-007F 10 90o Socket 4mm Red 1 J4 Deltron 571-0500 11 90oSocket 4mm Black 1 J6 Deltron 571-0100 12 Terminal block 2 pole insert 1 J5 DINKLE DT-123RA-02P 13 DIO 200V 250mA SOD323 SMT trr=50nSEC SWI 8 D39,D42,D43,D46,D47, D50,D51,D54 Diodes Inc. BAV21WS-7-F 14 DIO DUAL 70V 200mA 250mW Trr=6nS COM. CAT SOT23 2 D55,D56 Infineon BAV70 15 DIO 8.2V 225mW 5% Ir=5uA SOT23 SMT ZENER 8 D40,D41,D44,D45,D48, D49,D52,D53 ON Semi BZX84C8V2 LT1G 16 LED SuperYelGrn 100-130o 2040mcd h=1 0603 SMD 5 D9-D12,D14 Everlight 19-21SYGCS530E3TR8 17 RES 75R 125mW 1% 0805 SMT 4 R139-R142 Bourns CR0805-FX-75R0ELF 18 Resistor, 0 Ohm, 5%, 1/16W 0402 8 R128-R135 ASJ CR10-000ZK 19 RES 0R 250mW 5% 1206 SMT JUMPER<0.05R 2 R78,R79 Samsung RC3216J000CS 20 RES TK FLM 20K 250mW 1% 1206 6 R71-R76 Bourns CR1206-FX-2002ELF 21 Resistor, 20K, 5%, 1/16W 0603 9 R116-R124 ASJ CR16-203JL 22 RES TCK FLM 24.9K 62.5mW 1% 0603 SMT 1 R3 ASJ CR16-2492FL 23 Resistor, 30.9R 1%, 1/10W 0603 1 R1 KOA RK73H1JTTD30R9 Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 12 PD70210 Evaluation Board - U se r G u id e Item Description Qty Ref Des Mfr Manufacturer P\N F 24 RES TCK FLM 60.4K 62.5mW 1% 0603 SMT 1 R2 ASJ CR16-6042FL 25 DIP SWITCH 2 Positions 1 pole 1 SW1 Grayhill 7801T 26 TRN PNP -30V -1A SOT23 4 Q5,Q8-Q10 Fairchild FMMT549 27 TRN NPN 40V 600mA SOT23 300 mW 4 Q18-Q21 Diodes Inc. MMBT2222A-7-F 28 IC Dual N/P CH power mosfet 100v 6A SMT 2 U16,U17 Fairchild FDMQ8203 Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 13 PD70210 Evaluation Board - U se r G u id e 8 Board Layout This paragraph presents the layout of the evaluation board. The board is a 2 layer board. The layers are 2 Oz layers. Below figures present the two copper layers and the silk of the board for tracking devices placements. Figure 9: Top Silk Figure 10: Top Layer Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 14 PD70210 Evaluation Board - U se r G u id e Figure 11: Bottom Layer Figure 12: Bottom Silk Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 15 PD70210 Evaluation Board - U se r G u id e The information contained in the document is PROPRIETARY AND CONFIDENTIAL information of Microsemi and cannot be copied, published, uploaded, posted, transmitted, distributed or disclosed or used without the express duly signed written consent of Microsemi If the recipient of this document has entered into a disclosure agreement with Microsemi, then the terms of such Agreement will also apply . This document and the information contained herein may not be modified, by any person other than authorized personnel of Microsemi. No license under any patent, copyright, trade secret or other intellectual property right is granted to or conferred upon you by disclosure or delivery of the information, either expressly, by implication, inducement, estoppels or otherwise. Any license under such intellectual property rights must be approved by Microsemi in writing signed by an officer of Microsemi. Microsemi reserves the right to change the configuration, functionality and performance of its products at anytime without any notice. This product has been subject to limited testing and should not be used in conjunction with life-support or other mission-critical equipment or applications. Microsemi assumes no liability whatsoever, and Microsemi disclaims any express or implied warranty, relating to sale and/or use of Microsemi products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. The product is subject to other terms and conditions which can be located on the web at http://www.microsemi.com/legal/tnc.asp Revision History Revision Level / Date Para. Affected/Page Description 0.1 / 07-01-13 Initial revision 1.0 / 09-10-13 updated BOM (c) 2013 Microsemi Corp. All rights reserved. For support contact: sales_AMSG@microsemi.com Visit our web site at: www.microsemi.com Catalog Number: PD70210_UG_EVB Copyright (c) 2013 Microsemi Rev. 1.0 09-Oct-13 Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 Page 16