Preliminary Datasheet R1EX25512ASA00A R1EX25512ATA00A Serial Peripheral Interface 512K EEPROM (64-Kword x 8-bit) R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Description R1EX25xxx series is the Serial Peripheral Interface compatible (SPI) EEPROM (Electrically Erasable and Programmable ROM). They realize high speed, low power consumption and a high level of reliability by employing advanced MONOS memory technology and CMOS process and low voltage circuitry technology. They also have a 128-byte page programming function to make their write operation faster. Note: Renesas Electronics' serial EEPROMs are authorized for using consumer applications such as cellular phones, camcorders and audio equipments. Therefore, please contact Renesas Electronics' sales office before using industrial applications such as automotive systems, embedded controllers and meters. Features * Single supply: 1.8 V to 5.5 V * Serial Peripheral Interface compatible (SPI bus) SPI mode 0 (0,0), 3 (1,1) * Clock frequency: 5 MHz (2.5 V to 5.5 V), 3 MHz (1.8 V to 5.5 V) * Power dissipation: Standby: 5 A (max) Active (Read): 5 mA (max) Active (Write): 5 mA (max) * Automatic page write: 128-byte/page * Write cycle time: 5 ms (max) * Endurance: 1,000k Cycles @25 C * Data retention: 100 Years @25 C * Small size packages: SOP-8pin, TSSOP-8pin * Shipping tape and reel TSSOP-8pin : 3,000 IC/reel SOP-8pin : 2,500 IC/reel * Temperature range: -40 to +85C * Lead free product. R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 1 of 20 R1EX25512ASA00A/R1EX25512ATA00A Ordering Information Type No. Internal organization Operating voltage Frequency Package R1EX25512ASA00A 512k bit (65536 x 8-bit) 1.8 V to 5.5 V 5 MHz 150 mil 8-pin plastic SOP (2.5 V to 5.5 V) PRSP0008DF-B (FP-8DBV) Lead free 3 MHz (1.8 V to 5.5V) R1EX25512ATA00A 512k bit (65536 x 8-bit) 1.8 V to 5.5 V 5 MHz 8-pin plastic TSSOP (2.5 V to 5.5 V) PTSP0008JC-B (TTP-8DAV) Lead free 3 MHz (1.8 V to 5.5V) Pin Arrangement 8-pin SOP/TSSOP S 1 8 VCC Q 2 7 HOLD W 3 6 C VSS 4 5 D (Top view) Pin Description Pin name C D Q Function Serial clock Serial data input Serial data output S W HOLD Chip select Write protect Hold VCC Supply voltage VSS Ground R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 2 of 20 R1EX25512ASA00A/R1EX25512ATA00A Block Diagram High voltage generator C HOLD D Memory array Y-select & Sense amp. Y decoder W Address generator S Control logic VSS X decoder VCC Serial-parallel converter Q Absolute Maximum Ratings Parameter Supply voltage relative to VSS Input voltage relative to VSS Operating temperature range*1 Storage temperature range Symbol VCC VIN Topr Tstg Value -0.6 to +7.0 -0.3 to VCC +0.3 -40 to +85 -55 to +125 Unit V V C C Notes: 1. Including electrical characteristics and data retention. DC Operating Conditions Parameter Supply voltage Input voltage Operating temperature range Symbol VCC VSS VIH VIL Topr Min 1.8 0 VCC x 0.7 -0.3 -40 Typ 0 Max 5.5 0 VCC + 0.3 VCC x 0.3 +85 Unit V V V V C Capacitance (Ta = +25C, f = 1 MHz) Parameter Input capacitance (D,C, S, W ,HOLD) Output capacitance (Q) Note: Symbol 1 Cin* 1 CI/O* Min Typ Max Unit 6.0 8.0 pF pF Test conditions Vin = 0 V Vout = 0 V 1. Not 100% tested. R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 3 of 20 R1EX25512ASA00A/R1EX25512ATA00A Memory cell characteristics (VCC = 1.8 V to 5.5 V) Ta=25C 1,000k Cycles min. 100 Years min. Endurance Data retention Ta=85C 100k Cycles min. 10 Years min. Notes 1 1 Notes: 1. Not 100% tested Data at shipment Memory array : " 1 " (FF Hex) Status register SRWD, BP0, BP1: " 0 " DC Characteristics Parameter Input leakage current Symbol ILI Min Max 2 Unit A Output leakage current ILO 2 A VCC = 5.5 V, VOUT = 0 to 5.5 V (Q) Standby ISB 5 A VIN = VSS or VCC, S = VCC VCC = 5.5 V Active ICC1 3 mA VCC = 3.3 V, Read at 5 MHz VIN = VCC x 0.1 / VCC x 0.9 Q = OPEN 5 mA VCC = 5.5 V, Read at 5 MHz VIN = VCC x 0.1 / VCC x 0.9 Q = OPEN 3 mA VCC = 3.3 V, Write at 5 MHz VIN = VCC x 0.1 / VCC x 0.9 5 mA VCC x 0.8 VCC x 0.8 0.4 0.4 V V V V VCC = 5.5 V, Write at 5 MHz VIN = VCC x 0.1 / VCC x 0.9 VCC = 2.5 to 5.5 V, IOL = 2 mA VCC = 1.8 to 2.5 V, IOL = 1.5 mA VCC = 2.5 to 5.5 V, IOH = -2 mA VCC = 1.8 to 2.5 V, IOH= -0.4 mA VCC current ICC2 Output voltage R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 VOL1 VOL2 VOH1 VOH2 Test conditions VCC = 5.5 V, VIN = 0 to 5.5 V (S, D, C, HOLD, W) Page 4 of 20 R1EX25512ASA00A/R1EX25512ATA00A AC Characteristics Test Conditions * Input pulse levels: VIL = VCC x 0.2 VIH = VCC x 0.8 * Input rise and fall time: 5 ns * Input timing reference levels: VCC x 0.5 * Output reference levels: VCC x 0.5 * Output load: 1TTL Gate + 100 pF (Ta = -40 to +85C, VCC = 2.5 V to 5.5 V) Parameter Clock frequency S active setup time S not active setup time S deselect time S active hold time S not active hold time Clock high time Clock low time Clock rise time Clock fall time Data in setup time Data in hold time Clock low hold time after HOLD not active Clock low hold time after HOLD active Clock high setup time before HOLD active Clock high setup time before HOLD not active Output disable time Clock low to output valid Output hold time Output rise time Output fall time HOLD high to output low-Z HOLD low to output low-Z Write time Symbol fC tSLCH tSHCH tSHSL tCHSH tCHSL tCH tCL tCLCH tCHCL tDVCH tCHDX tHHCH tHLCH tCHHL Min 90 90 90 90 90 90 90 20 30 70 40 60 60 Max 5 1 1 Unit MHz ns ns ns ns ns ns ns s s ns ns ns ns ns ns Notes tCHHH Alt fSCK tCSS1 tCSS2 tCS tCSH tCLH tCLL tRC tFC tDSU tDH tSHQZ tCLQV tCLQX tQLQH tQHQL tHHQX tHLQZ tW tDIS tV tHO tRO tFO tLZ tHZ tWC 0 100 60 50 50 50 100 5 ns ns ns ns ns ns ns ms 2 1 1 2 2 2 2 2 2 Notes: 1. tCH + tCL 1/fC 2. Not 100% tested R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 5 of 20 R1EX25512ASA00A/R1EX25512ATA00A (Ta = -40 to +85C, VCC = 1.8 V to 5.5 V) Parameter Clock frequency S active setup time S not active setup time S deselect time S active hold time S not active hold time Clock high time Clock low time Clock rise time Clock fall time Data in setup time Data in hold time Clock low hold time after HOLD not active Clock low hold time after HOLD active Clock high setup time before HOLD active Symbol fC tSLCH tSHCH tSHSL tCHSH tCHSL tCH tCL tCLCH tCHCL tDVCH tCHDX tHHCH tHLCH tCHHL Clock high setup time before HOLD not active Output disable time tCHHH Alt fSCK tCSS1 tCSS2 tCS tCSH tCLH tCLL tRC tFC tDSU tDH tSHQZ tDIS 200 ns Clock low to output valid Output hold time Output rise time Output fall time HOLD high to output low-Z HOLD low to output low-Z Write time tCLQV tCLQX tQLQH tQHQL tHHQX tHLQZ tW tV 0 150 100 100 100 100 5 ns ns ns ns ns ns ms tHO tRO tFO tLZ tHZ tWC Min 100 100 250 100 100 150 150 30 50 200 200 120 120 Max 3 1 1 Unit MHz ns ns ns ns ns ns ns s s ns ns ns ns ns ns Notes 2 1 1 2 2 2 2 2 2 Notes: 1. tCH + tCL 1/fC 2. Not 100% tested R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 6 of 20 R1EX25512ASA00A/R1EX25512ATA00A Timing Waveforms Serial Input Timing tSHSL S tCHSL tCHSH tSHCH tSLCH C tDVCH D tCHCL tCLCH tCHDX MSB IN LSB IN High Impedance Q Hold Timing S tHHCH tHLCH tCHHL C tCHHH D tHLQZ tHHQX Q HOLD Output Timing S tSHQZ tCH C tCL D ADDR LSB IN tCLQV tCLQX Q tCLQX tCLQV LSB OUT tQLQH tQHQL R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 7 of 20 R1EX25512ASA00A/R1EX25512ATA00A Pin Function Serial data output (Q) This output signal is used to transfer data serially out of the device. Data is shifted out on the falling edge of serial clock (C). Serial data input (D) This input signal is used to transfer data serially into the device. It receives instructions, addresses, and the data to be written. Values are latched on the rising edge of serial clock (C). Serial clock (C) This input signal provides the timing of the serial interface. Instructions, addresses, or data present at serial data input (D) are latched on the rising edge of serial clock (C). Data on serial data output (Q) changes after the falling edge of serial clock (C). Chip select (S) When this input signal is high, the device is deselected and serial data output (Q) is at high impedance. Unless an internal write cycle is in progress, the device will be in the standby mode. Driving chip select (S) low enables the device, placing it in the active power mode. After power-up, a falling edge on chip select (S) is required prior to the start of any instruction. Hold (HOLD) The hold (HOLD) signal is used to pause any serial communications with the device without deselecting the device. During the hold condition, the serial data output (Q) is high impedance, and serial data input (D) and serial clock (C) are don't care. To start the hold condition, the device must be selected, with chip select (S) driven low. Write protect (W) The main purpose of this input signal is to freeze the size of the area of memory that is protected against write instructions (as specified by the values in the BP1 and BP0 bits of the status register). This pin must be driven either high or low, and must be stable during all write operations. R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 8 of 20 R1EX25512ASA00A/R1EX25512ATA00A Functional Description Status Register The following figure shows the Status Register Format. The Status Register contains a number of status and control bits that can be read or set (as appropriate) by specific instructions. Status Register Format b7 SRWD b0 0 0 0 BP1 BP0 WEL WIP Status Register Write Disable Block Protect Bits Write Enable Latch Bits Write In Progress Bits WIP bit: The Write In Progress (WIP) bit indicates whether the memory is busy with a Write or Write Status Register cycle. WEL bit: The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch. BP1, BP0 bits: The Block Protect (BP1, BP0) bits are non-volatile. They define the size of the area to be software protected against Write instructions. BP1, BP0 are " 0 " status at shipment. SRWD bit: The Status Register Write Disable (SRWD) bit is operated in conjunction with the write protect (W) signal. The Status Register Write Disable (SRWD) bit and write protect (W) signal allow the device to be put in the Hardware Protected mode. In this mode, the non-volatile bits of the Status Register (SRWD, BP1, BP0) become read-only bits. SRWD is " 0 " status at shipment. Instructions Each instruction starts with a single-byte code, as summarized in the following table. If an invalid instruction is sent (one not contained in the following table), the device automatically deselects itself. Instruction Set Instruction Description WREN WRDI Write Enable Write Disable RDSR WRSR READ WRITE Read Status Register Write Status Register Read from Memory Array Write to Memory Array R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Instruction Format 0000 0110 0000 0100 0000 0101 0000 0001 0000 0011 0000 0010 Page 9 of 20 R1EX25512ASA00A/R1EX25512ATA00A Write Enable (WREN): The Write Enable Latch (WEL) bit must be set prior to each WRITE and WRSR instruction. The only way to do this is to send a Write Enable instruction to the device. As shown in the following figure, to send this instruction to the device, chip select (S) is driven low, and the bits of the instruction byte are shifted in, on serial data input (D). The device then enters a wait state. It waits for the device to be deselected, by chip select (S) being driven high. Write Enable (WREN) Sequence S W VIH VIL VIH VIL 0 C D Q R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 1 2 3 4 5 6 7 VIH VIL Instruction VIH VIL High-Z Page 10 of 20 R1EX25512ASA00A/R1EX25512ATA00A Write Disable (WRDI): One way of resetting the Write Enable Latch (WEL) bit is to send a Write Disable instruction to the device. As shown in the following figure, to send this instruction to the device, chip select (S) is driven low, and the bits of the instruction byte are shifted in, on serial data input (D). The device then enters a wait state. It waits for the device to be deselected, by chip select (S) being driven high. The Write Enable Latch (WEL) bit, in fact, becomes reset by any of the following events: Power-up WRDI instruction execution WRSR instruction completion WRITE instruction completion Write Disable (WRDI) Sequence S W VIH VIL VIH VIL 0 C D Q R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 1 2 3 4 5 6 7 VIH VIL Instruction VIH VIL High-Z Page 11 of 20 R1EX25512ASA00A/R1EX25512ATA00A Read Status Register (RDSR): The Read Status Register (RDSR) instruction allows the Status Register to be read. The Status Register may be read at any time, even while a Write or Write Status Register cycle is in progress. When one of these cycles is in progress, it is recommended to check the Write In Progress (WIP) bit before sending a new instruction to the device. It is also possible to read the Status Register continuously, as shown in the following figure. Read Status Register (RDSR) Sequence S W VIH VIL VIH VIL 0 C D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VIH VIL VIH VIL Status Register Out Q High-Z 7 6 5 4 3 2 1 0 7 The status and control bits of the Status Register are as follows: WIP bit: The Write In Progress (WIP) bit indicates whether the memory is busy with a Write or Write Status Register cycle. When set to 1, such a cycle is in progress. When reset to 0, no such cycles are in progress. WEL bit: The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch. When set to 1, the internal Write Enable Latch is set. When set to 0, the internal Write Enable Latch is reset and no Write or Write Status Register instructions are accepted. BP1, BP0 bits: The Block Protect (BP1, BP0) bits are non-volatile. They define the size of the area to be software protected against Write instructions. These bits are written with the Write Status Register (WRSR) instruction. When one or both of the Block Protect (BP1, BP0) bits are set to 1, the relevant memory area (as defined in the Write Protect Block Size table) becomes protected against Write (WRITE) instructions. The Block Protect (BP1, BP0) bits can be written provided that the Hardware Protected mode has not been set. SRWD bit: The Status Register Write Disable (SRWD) bit is operated in conjunction with the write protect (W) signal. The Status Register Write Disable (SRWD) bit and write protect (W) signal allows the device to be put in the Hardware Protected mode (When the Status Register Write Disable (SRWD) bit is set to 1, and write protect (W) signal is driven low). In this mode, the non-volatile bits of the Status Register (SRWD, BP1, BP0) become read-only bits and the Write Status Register (WRSR) instruction is no longer accepted for execution. R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 12 of 20 R1EX25512ASA00A/R1EX25512ATA00A Write Status Register (WRSR): The Write Status Register (WRSR) instruction allows new values to be written to the Status Register. Before it can be accepted, a Write Enable (WREN) instruction must previously have been executed. After the Write Enable (WREN) instruction has been decoded and executed, the device sets the Write Enable Latch (WEL). The instruction sequence is shown in the following figure. The Write Status Register (WRSR) instruction has no effect on b6, b5, b4, b1 and b0 of the Status Register. b6, b5 and b4 are always read as 0. Chip select (S) must be driven high after the rising edge of serial clock (C) that latches in the eighth bit of the data byte, and before the next rising edge of serial clock (C). Otherwise, the Write Status Register (WRSR) instruction is not executed. As soon as chip select (S) is driven high, the self-timed Write Status Register cycle (whose duration is tW) is initiated. While the Write Status Register cycle is in progress, the Status Register may still be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Write Status Register cycle, and is 0 when it is completed. When the cycle is completed, Write Enable Latch (WEL) is reset. The Write Status Register (WRSR) instruction allows the user to change the values of the Block Protect (BP1, BP0) bits, to define the size of the area that is to be treated as read-only, as defined in the Status Register Format table. The Write Status Register (WRSR) instruction also allows the user to set or reset the Status Register Write Disable (SRWD) bit in accordance with the write protect (W) signal. The Status Register Write Disable (SRWD) bit and write protect (W) signal allows the device to be put in the Hardware Protected Mode (HPM). The Write Status Register (WRSR) instruction is not executed once the Hardware Protected Mode (HPM) is entered. The contents of the Status Register Write Disable (SRWD) and Block Protect (BP1, BP0) bits are frozen at their current values just before the start of the execution of the Write Status Register (WRSR) instruction. The new, updated values take effect at the moment of completion of the execution of Write Status Register (WRSR) instruction. Write Status Register (WRSR) Sequence S W VIH VIL VIH VIL 0 C 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VIH VIL Status Register In D VIH VIL Q R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 7 6 5 4 3 2 1 0 MSB High-Z Page 13 of 20 R1EX25512ASA00A/R1EX25512ATA00A Read from Memory Array (READ): As shown in the following figure, to send this instruction to the device, chip select (S) is first driven low. The bits of the instruction byte and the address bytes are then shifted in, on serial data input (D). The addresses are loaded into an internal address register, and the byte of data at that address is shifted out, on serial data output (Q). If chip select (S) continues to be driven low, the internal address register is automatically incremented, and the byte of data at the new address is shifted out. When the highest address is reached, the address counter rolls over to zero, allowing the Read cycle to be continued indefinitely. The whole memory can, therefore, be read with a single READ instruction. The Read cycle is terminated by driving chip select (S) high. The rising edge of the chip select (S) signal can occur at any time during the cycle. The addressed first byte can be any byte within any page. The instruction is not accepted, and is not executed, if a Write cycle is currently in progress. Read from Memory Array (READ) Sequence S W C D VIH VIL VIH VIL VIH 0 1 2 VIL 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 16-Bit Address Instruction VIH 15 14 13 3 2 1 0 VIL Data Out 1 High-Z Q 7 6 5 4 3 Data Out 2 2 1 0 7 Note: 1. The memory size is shown in the following table. Address Range Bits Device Address bits R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 R1EX25512A A15 to A0 Page 14 of 20 R1EX25512ASA00A/R1EX25512ATA00A Write to Memory Array (WRITE): As shown in the following figures, to send this instruction to the device, chip select (S) is first driven low. The bits of the instruction byte, address byte, and at least one data byte are then shifted in, on serial data input (D). The instruction is terminated by driving chip select (S) high at a byte boundary of the input data. In the case of the first figure, this occurs after the eighth bit of the data byte has been latched in, indicating that the instruction is being used to write a single byte. The self-timed Write cycle starts, and continues for a period tW (as specified in AC Characteristics). At the end of the cycle, the Write In Progress (WIP) bit is reset to 0. If, though, chip select (S) continues to be driven low, as shown in the second figure, the next byte of the input data is shifted in, so that more than a single byte, starting from the given address towards the end of the same page, can be written in a single internal Write cycle. Each time a new data byte is shifted in, the least significant bits of the internal address counter are incremented. If the number of data bytes sent to the device exceeds the page boundary, the internal address counter rolls over to the beginning of the page, and the previous data there are overwritten with the incoming data. (The page size of these device is 128 bytes). The instruction is not accepted, and is not executed, under the following conditions: If the Write Enable Latch (WEL) bit has not been set to 1 (by executing a Write Enable instruction just before) If a Write cycle is already in progress If the device is deselected If the addressed page is in the region protected by the Block Protect (BP1 and BP0) bits. Byte Write (WRITE) Sequence (1 Byte) S W C VIH VIL VIH VIL VIH 0 1 2 3 4 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 VIL Instruction D 5 VIH 16-Bit Address 15 14 13 3 2 Data Byte 1 1 0 7 6 5 4 3 2 1 0 VIL Q High-Z Note: 1. The memory size is shown in the Address Range Bits table. R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 15 of 20 R1EX25512ASA00A/R1EX25512ATA00A Byte Write (WRITE) Sequence (Page) S W C VIH VIL VIH VIL 0 VIH 1 2 3 4 5 6 7 8 9 16-Bit Address VIH 15 14 13 W C 2 1 0 7 6 5 4 3 2 1 1 0 0 High-Z VIH VIL VIH VIL VIH 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 VIL Data Byte 2 D 3 Data Byte 1 VIL Q S 20 21 22 23 24 25 26 27 28 29 30 31 VIL Instruction D 10 7 6 Q 5 4 3 2 Data Byte 3 1 0 7 6 5 4 3 2 Data Byte N 1 0 6 5 4 3 2 High-Z Note: 1. The memory size is shown in the Address Range Bits table. R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 16 of 20 R1EX25512ASA00A/R1EX25512ATA00A Data Protect The protection features of the device are summarized in the following tables. When the Status Register Write Disable (SRWD) bit of the Status Register is 0 (its initial delivery state), it is possible to write to the Status Register provided that the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction, regardless whether write protect (W) is driven high or low. When the Status Register Write Disable (SRWD) bit of the Status Register is set to 1, two cases need to be considered, depending on the state of write protect (W): If write protect (W) is driven high, it is possible to write to the Status Register provided that the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction. If write protect (W) is driven low, it is not possible to write to the Status Register even if the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction. (Attempts to write to the Status Register are rejected, and are not accepted for execution). As a consequence, all the data bytes in the memory area that are software protected (SPM) by the Block Protect (BP1, BP0) bits of the Status Register, are also hardware protected against data modification. Regardless of the order of the two events, the Hardware Protected Mode (HPM) can be entered: By setting the Status Register Write Disable (SRWD) bit after driving write protect (W) low. By driving write protect (W) low after setting the Status Register Write Disable (SRWD) bit. The only way to exit the Hardware Protected Mode (HPM) once entered is to pull write protect (W) high. If write protect (W) is permanently tied high, the Hardware Protected Mode (HPM) can never be activated, and only the Software Protected Mode (SPM), using the Block Protect (BP1, BP0) bits of the Status Register, can be used. Write Protected Block Size Status register bits BP1 BP0 0 1 0 1 0 0 1 1 Protected blocks None Upper quarter Upper half Whole memory Array addresses protected R1EX25512A None C000h - FFFFh 8000h - FFFFh 0000h - FFFFh Protection Modes W signal SRWD bit 1 0 0 0 1 1 0 1 Note: Mode Write protection of the status register Memory protect 1 Protected area* Unprotected area*1 Software Status register is writable Write protected protected (SPM) (if the WREN instruction has set the WEL bit). The values in the BP1 and BP0 bits can be changed. Ready to accept Write instructions Write protected Hardware Status register is protected (HPM) hardware write protected. The values in the BP1 and BP0 bits cannot be changed. Ready to accept Write instructions 1. As defined by the values in the Block Protected (BP1, BP0) bits of the Status Register, as shown in the Write Protected Block Size table. R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 17 of 20 R1EX25512ASA00A/R1EX25512ATA00A Hold Condition The hold (HOLD) signal is used to pause any serial communications with the device without resetting the clocking sequence.During the hold condition, the serial data output (Q) is high impedance, and serial data input (D) and serial clock (C) are don't care.To enter the hold condition, the device must be selected, with chip select (S) low. Normally, the device is kept selected, for the whole duration of the hold condition. Deselecting the device while it is in the hold condition, has the effect of resetting the state of the device, and this mechanism can be used if it is required to reset any processes that had been in progress. The hold condition starts when the hold (HOLD) signal is driven low at the same time as serial clock (C) already being low (as shown in the following figure).The hold condition ends when the hold (HOLD) signal is driven high at the same time as serial clock (C) already being low. The following figure also shows what happens if the rising and falling edges are not timed to coincide with serial clock (C) being low. Hold Condition Activation HOLD status HOLD status C HOLD Notes Data Protection at VCC On/Off When VCC is turned on or off, noise on S inputs generated by external circuits (CPU, etc) may act as a trigger and turn the EEPROM to unintentional program mode. To prevent this unintentional programming, this EEPROM have a power on reset function. Be careful of the notices described below in order for the power on reset function to operate correctly. * S should be fixed to VCC during VCC on/off. Low to high or high to low transition during VCC on/off may cause the trigger for the unintentional programming. * VCC should be turned on/off after the EEPROM is placed in a standby state. * VCC should be turned on from the ground level (VSS) in order for the EEPROM not to enter the unintentional programming mode. * VCC turn on rate should be slower than 2 s/V. * When WRSR or WRITE instruction is executed before VCC turns off, VCC should be turned off after waiting write cycle time (tW). * When setting the chip select signal (S) to the low level at power on, wait for 10 ms or longer after the supply voltage 1.8V. 1.8V (Vccmin) Vcc S 10ms min R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 Page 18 of 20 R1EX25512ASA00A/R1EX25512ATA00A Package Dimensions R1EX25512ASA00A (PRSP0008DF-B / Previous Code: FP-8DBV) JEITA Package Code P-SOP8-3.9x4.89-1.27 RENESAS Code PRSP0008DF-B *1 Previous Code FP-8DBV D 8 MASS[Typ.] 0.08g NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. F 5 *2 c E HE bp Reference Symbol Index mark Terminal cross section ( Ni/Pd/Au plating ) Dimension in Millimeters Min Nom Max D 4.89 5.15 E 3.90 A2 1 Z 4 e *3 A1 bp x 0.14 L1 0.35 0.40 0.45 0.15 0.20 0.25 6.02 6.20 b1 c A c A1 L y Detail F 0.254 1.73 bp 1 0 HE 5.84 8 1.27 e x 0.25 y 0.10 Z 0.69 0.406 L L R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 0.102 A M 1 0.60 0.889 1.06 Page 19 of 20 R1EX25512ASA00A/R1EX25512ATA00A R1EX25512ATA00A (PTSP0008JC-B / Previous Code: TTP-8DAV) JEITA Package Code P-TSSOP8-4.4x3-0.65 RENESAS Code PTSP0008JC-B *1 Previous Code TTP-8DAV MASS[Typ.] 0.034g D 8 F 5 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. c *2 E HE bp Terminal cross section ( Ni/Pd/Au plating ) Reference Dimension in Millimeters Symbol Index mark L1 1 e *3 bp x M A1 A Z 4 L Detail F y R10DS0046EJ0200 Rev.2.00 Oct.04, 2010 D E A2 A1 A bp b1 c c1 HE e x y Z L L1 Min Nom Max 3.00 3.30 4.40 0.03 0.07 0.10 1.10 0.15 0.20 0.25 0.10 0.15 0.20 0 8 6.20 6.40 6.60 0.65 0.13 0.10 0.805 0.40 0.50 0.60 1.00 Page 20 of 20 Revision History Rev. 1.00 2.00 Date Jan. 15, 2010 Oct. 04, 2010 R1EX25512ASA00A/R1EX25512ATA00A Data Sheet Description Summary Page Initial issue Apply to Renesas Electronics' new format and new document number. Addition of 8-pin SOP package. Which product Type No. is R1EX25512ASA00A. All trademarks and registered trademarks are the property of their respective owners. C-1 Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. 2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. 4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 7. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada Tel: +1-905-898-5441, Fax: +1-905-898-3220 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-585-100, Fax: +44-1628-585-900 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Dusseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 7F, No. 363 Fu Shing North Road Taipei, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632 Tel: +65-6213-0200, Fax: +65-6278-8001 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 (c) 2010 Renesas Electronics Corporation. All rights reserved. Colophon 1.0