SCOPE: QUAD, SPDT, CMOS ANALOG SWITCH Device Type 01 Generic Number MAX333M(x)/883B SMD Number 5962-93180 Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter SMD Maxim R JP Mil-Std-1835 GDIP1-T20 or CDIP2-T20 Case Outline Package Code 20 LEAD CERDIP J20 Absolute Maximum Ratings Voltage Referenced to VV+ to V- ................................................................................................................................ 44V V+ to GND ............................................................................................................................ 44V V- to GND ........................................................................................................................... -44V VIN, VCOM, VNO, VNC ....................................................................................................... V+ to VVNO to VNC ............................................................................................................................ 32V Current, Any terminal except VCOM, VNO, or VNC ............................................................ 30mA Current, VCOM, VNO, or VNC ............................................................................................... 20mA Peak Current, VCOM, VNO, or VNC (Pulsed at 1ms, 10% duty cycle max) .......................... 70mA Lead Temperature (soldering, 10 seconds) .......................................................................... +300C Storage Temperature ............................................................................................. -65C to +150C Continuous Power Dissipation 1/ ........................................................................ TA=+70C 20 lead CERDIP(derate 11.1mW/C above +70C) .................................................. 889mW Junction Temperature TJ ........................................................................................ +150C Thermal Resistance, Junction to Case, JC: Case Outline 20 lead CERDIP................................................................... 40C/W Thermal Resistance, Junction to Ambient, JA: Case Outline 20 lead CERDIP................................................................... 90C/W Recommended Operating Conditions Ambient Operating Range (TA) ............................................................ -55C to +125C Positive Supply Voltage (V+) ................................................................................... +15V Negative Supply Voltage (V-) ................................................................................... -15V VINL (max) ................................................................................................................ 0.8V VINH (min) ................................................................................................................ 2.4V 1/ Device mounted with all leads soldered to PC board. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of MAX333M/883B for /883B and SMD 5962-93180 19-0056 Page 2 of Rev. C 6 TABLE 1. ELECTRICAL TESTS TEST SWITCH Analog-Signal Range Drain-Source ON Resistance ON Leakage Current OFF Leakage Current INPUT Input Current SUPPLY Positive Supply Current Symbol VANALOG rDS(ON) ICOM =1mA, VANA=10V, IL(ON) VANA=14V, VOFF=14V IL(OFF) VANA=14V, VOFF=14V IIN Group A Subgroup Device type Limits Min 2/ Limits Max 2/ -15 15 Units 1,2,3 All 1 2,3 1 2 All All -5 -200 175 250 5 200 1 2 All -5 -100 5 100 nA 1,2,3 All -10 10 A V nA I+ All channels on or off 1 2,3 All -.25 -.50 .25 .50 mA I- All channels on or off 1 2,3 All -.25 -.50 .25 .50 mA 9 10,11 9 10,11 9 10,11 All Negative Supply Current DYNAMIC Turn-On Time tON Turn-Off Time tOFF Break-BeforeMake Delay 3/ CONDITIONS -55 C <=TA<= +125C V+=+15V, V-=-15V, GND=0V VINH=2.4V, VINL=0.8V Unless otherwise specified tOPEN All All -200 50 5 500 1000 1000 2000 ns ns ns NOTE 2: The algebraic convention whereby the most negative value is a minimum and the most positive value is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. NOTE 3: Guaranteed, but not tested. ---------------------------- Electrical Characteristics of MAX333M/883B for /883B and SMD 5962-93180 19-0056 Page 3 of Rev. C 6 ORDERING INFORMATION: MAX333MJP/883B 20 CDIP SMD Number 5962-9318001MRA TERMINAL CONNECTIONS: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MAX333MJP/883B J20 IN1 NO1 COM1 NC1 VGND NC2 COM2 NO2 IN2 IN3 NO3 COM3 NC3 NC V+ NC4 COM4 NO4 IN4 ---------------------------- Electrical Characteristics of MAX333M/883B for /883B and SMD 5962-93180 19-0056 Page 4 of Rev. C 6 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * Subgroups per Method 5005, Table 1 1 1*, 2, 3, 9, 10, 11 1, 2, 3, 9, 10, 11 1 PDA applies to Subgroup 1 only. ---------------------------- Electrical Characteristics of MAX333M/883B for /883B and SMD 5962-93180 19-0056 Page 5 of Rev. C 6