SN74LV373A-Q1 OCTAL TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCLS586C - JUNE 2004 - REVISED OCTOBER 2007 FEATURES 1 * * * * * * * * PW PACKAGE (TOP VIEW) Qualified for Automotive Applications 2-V to 5.5-V VCC Operation Maximum tpd of 8.5 ns at 5 V Typical VOLP (Output Ground Bounce) < 0.8 V at VCC = 3.3 V, TA = 25C Typical VOHV (Output VOH Undershoot) > 2.3 V at VCC = 3.3 V, TA = 25C Supports Mixed-Mode Voltage Operation on All Ports Ioff Supports Partial-Power-Down Mode Operation Latch-Up Performance Exceeds 250 mA Per JESD 17 OE 1Q 1D 2D 2Q 3Q 3D 4D 4Q GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 8Q 8D 7D 7Q 6Q 6D 5D 5Q LE DESCRIPTION/ORDERING INFORMATION The SN74LV373A device is an octal transparent D-type latch designed for 2-V to 5.5-V VCC operation. While the latch-enable (LE) input is high, the Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs are latched at the logic levels set up at the D inputs. A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. OE does not affect the internal operations of the latches. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE shall be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. ORDERING INFORMATION (1) PACKAGE (2) TA -40C to 85C (1) (2) TSSOP - PW Reel of 2000 ORDERABLE PART NUMBER SN74LV373AIPWRQ1 TOP-SIDE MARKING LV373AI For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2007, Texas Instruments Incorporated SN74LV373A-Q1 OCTAL TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCLS586C - JUNE 2004 - REVISED OCTOBER 2007 FUNCTION TABLE (EACH LATCH) INPUTS OUTPUT OE LE D Q L H H H L H L L L L X Q0 H X X Z LOGIC DIAGRAM (POSITIVE LOGIC) OE LE 1 11 C1 1D 3 2 1Q 1D To Seven Other Channels Absolute Maximum Ratings (1) over operating free-air temperature (unless otherwise noted) MIN MAX VCC Supply voltage range -0.5 7 V VI Input voltage range (2) -0.5 7 V -0.5 7 V -0.5 VCC + 0.5 (2) UNIT VO Voltage range applied to any output in the high-impedance or power-off state VO Output voltage range (2) (3) IIK Input clamp current VI < 0 -20 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current VO = 0 to VCC 35 mA Continuous current through VCC or GND JA Package thermal impedance (4) Tstg Storage temperature range (1) (2) (3) (4) 2 -65 V 70 mA 83 C/W 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. This value is limited to 5.5 V maximum. The package thermal impedance is calculated in accordance with JESD 51-7. Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated SN74LV373A-Q1 OCTAL TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCLS586C - JUNE 2004 - REVISED OCTOBER 2007 Recommended Operating Conditions (1) VCC MIN MAX 2 5.5 Supply voltage VCC = 2 V VIH High-level input voltage Low-level input voltage VI Input voltage VO Output voltage VCC = 2.3 V to 2.7 V VCC x 0.7 VCC = 3 V to 3.6 V VCC x 0.7 VCC = 4.5 V to 5.5 V VCC x 0.7 V 0.5 VCC = 2.3 V to 2.7 V VCC x 0.3 VCC = 3 V to 3.6 V VCC x 0.3 0 5.5 High or low state 0 VCC 3-state 0 5.5 VCC = 2 V -50 VCC = 2.3 V to 2.7 V High-level output current t/v -8 50 VCC = 2.3 V to 2.7 V 8 VCC = 4.5 V to 5.5 V 16 VCC = 2.3 V to 2.7 V 200 VCC = 3 V to 3.6 V 100 VCC = 4.5 V to 5.5 V TA (1) A mA A 2 VCC = 3 V to 3.6 V Input transition rise or fall rate V -16 VCC = 2 V Low-level output current V -2 VCC = 3 V to 3.6 V VCC = 4.5 V to 5.5 V IOL V VCC x 0.3 VCC = 4.5 V to 5.5 V IOH V 1.5 VCC = 2 V VIL UNIT mA ns/V 20 Operating free-air temperature -40 85 C All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VOH VOL TEST CONDITIONS VCC MIN IOH = -50 A 2 V to 5.5 V IOH = -2 mA 2.3 V IOH = -8 mA 3V 2.48 IOH = -16 mA 4.5 V 3.8 TYP MAX UNIT VCC - 0.1 2 V IOL = 50 A 2 V to 5.5 V IOL = 2 mA 2.3 V 0.4 IOL = 8 mA 3V 0.44 IOL = 16 mA 4.5 V 0.55 0.1 V II VI = 5.5 V or GND 0 to 5.5 V 1 A IOZ VO = VCC or GND 5.5 V 5 A ICC VI = VCC or GND, IO = 0 5.5 V 20 A Ioff VI or VO = 0 to 5.5 V 5 A Ci VI = VCC or GND Copyright (c) 2004-2007, Texas Instruments Incorporated 0 3.3 V 2.9 Submit Documentation Feedback pF 3 SN74LV373A-Q1 OCTAL TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCLS586C - JUNE 2004 - REVISED OCTOBER 2007 Timing Requirements over recommended operating free-air temperature range, VCC = 2.5 V 0.2 V (unless otherwise noted) (see Figure 1) MIN tw Pulse duration, LE high tsu Setup time, data before LE th Hold time, data after LE MAX UNIT 6.5 ns High or low 5 ns High or low 1.5 ns Timing Requirements over recommended operating free-air temperature range, VCC = 3.3 V 0.3 V (unless otherwise noted) (see Figure 1) MIN tw Pulse duration, LE high tsu Setup time, data before LE th Hold time, data after LE MAX UNIT 5 ns High or low 4 ns High or low 1 ns Timing Requirements over recommended operating free-air temperature range, VCC = 5 V 0.5 V (unless otherwise noted) (see Figure 1) MIN MAX UNIT tw Pulse duration, LE high 5 ns tsu Setup time, data before LE High or low 4 ns th Hold time, data after LE High or low 1 ns Switching Characteristics over recommended operating free-air temperature range, VCC = 2.5 V 0.2 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) LOAD CAPACITANCE MIN MAX UNIT D Q 1 17 LE Q 1 19 ten OE Q 1 19 ns tdis OE Q 1 15 ns D Q 1 21 LE Q 1 22 ten OE Q 1 22 ns tdis OE Q 1 19 ns 2 ns tpd tpd tsk(o) CL = 15 pF CL = 50 pF CL = 50 pF ns ns Switching Characteristics over recommended operating free-air temperature range, VCC = 3.3 V 0.3 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) MIN MAX UNIT D Q 1 13.5 LE Q 1 13 ten OE Q 1 13.5 ns tdis OE Q 1 12 ns D Q 1 17 LE Q 1 16.5 ten OE Q 1 17 ns tdis OE Q 1 15 ns 1.5 ns tpd tpd tsk(o) 4 LOAD CAPACITANCE Submit Documentation Feedback CL = 15 pF CL = 50 pF CL = 50 pF ns ns Copyright (c) 2004-2007, Texas Instruments Incorporated SN74LV373A-Q1 OCTAL TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCLS586C - JUNE 2004 - REVISED OCTOBER 2007 Switching Characteristics over recommended operating free-air temperature range, VCC = 5 V 0.5 V (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) D Q LE Q ten OE Q tdis OE Q PARAMETER tpd LOAD CAPACITANCE MIN MAX 1 8.5 1 8.5 1 9.5 ns 1 8.5 ns CL = 15 pF UNIT ns D Q 1 10.5 LE Q 1 10.5 ten OE Q 1 11.5 ns tdis OE Q 1 10.5 ns 1 ns tpd tsk(o) CL = 50 pF CL = 50 pF ns Noise Characteristics (1) VCC = 3.3 V, CL = 50 pF, TA = 25C (unless otherwise noted) TYP MAX VOL(P) Quiet output, maximum dynamic VOL MIN 0.6 0.8 V VOL(V) Quiet output, minimum dynamic VOL -0.6 -0.8 V VOH(V) Quiet output, minimum dynamic VOH 2.9 VIH(D) High-level dynamic input voltage VIL(D) Low-level dynamic input voltage (1) UNIT V 2.31 V 0.99 V Characteristics are for surface-mount packages only. Operating Characteristics TA = 25C PARAMETER Cpd Power dissipation capacitance (outputs enabled) Copyright (c) 2004-2007, Texas Instruments Incorporated TEST CONDITIONS CL = 50 pF, f = 10 MHz VCC TYP 3.3 V 17.4 5V 19.5 Submit Documentation Feedback UNIT pF 5 SN74LV373A-Q1 OCTAL TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS www.ti.com SCLS586C - JUNE 2004 - REVISED OCTOBER 2007 PARAMETER MEASUREMENT INFORMATION VCC From Output Under Test Test Point RL = 1 k From Output Under Test CL (see Note A) S1 Open TEST GND CL (see Note A) LOAD CIRCUIT FOR TOTEM-POLE OUTPUTS S1 Open VCC GND VCC tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open Drain LOAD CIRCUIT FOR 3-STATE AND OPEN-DRAIN OUTPUTS VCC 50% VCC Timing Input tw tsu VCC 50% VCC Input 50% VCC 0V th VCC 50% VCC Data Input 50% VCC 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC 50% VCC Input 50% VCC 0V tPLH In-Phase Output tPHL 50% VCC tPHL Out-of-Phase Output VOH 50% VCC VOL Output Waveform 1 S1 at VCC (see Note B) VOH 50% VCC VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 50% VCC 50% VCC 0V tPLZ tPZL VCC 50% VCC tPZH tPLH 50% VCC VCC Output Control Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ 50% VCC VOH - 0.3 V VOH 0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics:PRR 1 MHz, ZO = 50 , tr 3 ns, tf 3 ns. D. The outputs are measured one at a time, with one input transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPHL and tPLH are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 6 Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated PACKAGE OPTION ADDENDUM www.ti.com 18-Dec-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74LV373AIPWRG4Q1 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LV373AIPWRQ1 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN74LV373A-Q1 : * Catalog: SN74LV373A NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated