A. SCOPE This specification applies piezo audio indicator, KPEG200A , KPEG200A B. SPECIFICATION No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Item Operating Frequency Operating Volt. range Current consumption Sound pressure level Rated Voltage Tone Operating temp. Storage temp. Dimension Weight (MAX) Material Terminal Environmental Protection Regulation Unit Specification Condition KHz 3.1 0.5 VDC 3 ~ 20 mA MAX 8 at 12VDC dB MIN 88 at 30 cm/12VDC VDC 12 Continuous -30 ~ + 85 -40 ~ + 95 mm 23.8 x H14.5 gram 4.5 C. APPEARANCE DRAWING See appearance drawing ABS UL-94 1/16" HB HIGH HEAT BLACK Wire type See appearance drawing RoHS Black Tol: 0.5 Unit: mm KINGSTATE ELECTRONICS CORP 2/5 KPEG200A KINGSTATE Red KPEG200A UL1095 LF 28AWG D. MEASURING METHOD S.P.L. Measuring Circuit Mic : RION S.P.L meter UC30 or equivalent MicRION UC30 S.GHewlett Packard 33120A Function Generator or equivalent S.GHewlett Packard 33120A E. VOLTAGE: SOUND PRESSURE LEVEL / VOLTAGE: CURRENT CONSUMPTION CHARACTERISTICS / P I KINGSTATE ELECTRONICS CORP 3/5 KPEG200A F. MECHANICAL CHARACTERISTICS No. 1 2 3 4 Item Test Condition Evaluation standard 90% min. stripped wires shall be Solderability Stripped wires of lead wires are immersed in rosin for 5 seconds and wet with solder.(Except the edge of terminal) then immersed in solder bath of +2705 for 30.5 seconds. (Connector excepted) 90% 5 ,+2705 30.5 . () .() The pull force shall be applied to double lead wire Horizontal 3.0N(0.306kg) for 30 seconds. Lead Wire Pull No damage and cutting off. Strength Vertical 2.0N(0.204kg) for 30 seconds. ,. 3.0N(0.306kg), 2.0N(0.204kg) ,30 . Buzzer shall be measured after being applied vibration of amplitude of The value of oscillation 1.5mm with 10 to 55hz band of vibration frequency to each of 3 frequency/ current consumption Vibration should be in 10% compared per-pendicular directions for 2 hours. with initial ones .The SPL should 1055HZ 1.5mm X.Y.Z 3 , 2 . be in 10dB compared with The part only shall be dropped from a height of 75cm onto a 40mm thick initial one. Drop test wooden board 3 times in 3 axes (X.Y.Z). (a total of 9 times). 10%. 75 , X.Y.Z.3 ,3 , 40mm . 10dB . G. ENVIRONMENT TEST No. 1 2 Item High temp. test Low temp. test 3 Humidity test 4 Temp. cycle test Test Condition Evaluation standard After being placed in a chamber at +95 for 240 hours +95 240 After being placed in a chamber at -40 for 240 hours -40 240 After being placed in a chamber at +40 and 905% relative humidity for 240 hours Being placed for 4 hours at +40, 905% 240 +25, buzzer shall be The part shall be subjected to 5 cycles. One cycle shall be consist of measured. The value of 5 , oscillation frequency/ current consumption should be in10% +95 compared with initial ones .The SPL should be in10dB +25 +25 compared with initial one. , +25 4 , -40 10%. 10dB . 0.5hr 0.5hr 0.25 0.5hr 0.5hr 0.5hr 0.25 3hours KINGSTATE ELECTRONICS CORP 4/5 KPEG200A H. RELIABILITY TEST No. 1 Item Test condition Evaluation standard 1.Continuous life test () 48 hours continuous operation at +70 with rated voltage applied. +70,48 . Operating life 2.Intermittent life test () test A duty cycle of 1 minute on, 1 minutes off, a minimum of 5000 times at room temp.( +252)and rated voltage applied. (+252), , 1 /1 , 5000 . Being placed for 4 hours at +25, buzzer shall be measured. The value of oscillation frequency/ current consumption should be in 10% compared with initial ones .The SPL should be in 10dB compared with initial one. , +25 4 , 10%. 10dB . TEST CONDITION. Standard Test Condition Judgement Test Condition : : : : a) Temperature : +5 ~ +35 a) : +5 ~ +35 a) Temperature : +25 2 a) : +25 2 b) Humidity : 45-85% b) : 45-85% b) Humidity : 60-70% b) : 60-70% c) Pressure : 860-1060mbar c) : 860-1060mbar c) Pressure : 860-1060mbar c) : 860-1060mbar I. PACKING STANDARD Paper 10x21PCS=210PCS Out Box Paper Out Box 290mm Carton Box (10PCS Out Box) 550 mm mm 330 Out Box 310mmx248mmx49mm 1x210PCS=210PCS Carton Box 550mmx330mmx290mm 210PCSx10=2,100PCS KINGSTATE ELECTRONICS CORP 5/5 KPEG200A