Description
The HCPL-22XX, HCPL-02XX, and HCNW22XX are optical-
ly-coupled logic gates. The HCPL-22XX, and HCPL-02XX
contain a GaAsP LED while the HCNW22XX contains
an AlGaAs LED. The detectors have totem pole output
stages and optical receiver input stages with built-in
Schmitt triggers to provide logic-compatible waveforms,
eliminat ing the need for additional waveshaping.
A superior internal shield on the HCPL-2211/12, HCPL-
0211, HCPL-2232 and HCNW2211 guarantees common
mode transient immunity of 10 kV/μs at a common
mode voltage of 1000 volts.
Functional Diagram
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this
component to prevent damage and/or degradation which may be induced by ESD. The components
featured in this datasheet are not to be used in military or aerospace applications or environments.
A 0.1 μF bypass capacitor must be connected between pins 5 and 8.
HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212,
HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211,
HCNW2201, HCNW2211
Very High CMR, Wide VCC Logic Gate Optocouplers
Data Sheet
Features
10 kV/μs minimum Common Mode Rejection
(CMR) at VCM = 1000 V (HCPL-2211/2212/0211/2232,
HCNW2211)
Wide operating VCC range: 4.5 to 20 Volts
300 ns propagation delay guaranteed over the full
temperature range
5 Mbd typical signal rate
Low input current (1.6 mA to 1.8 mA)
Hysteresis
Totem pole output (no pullup resistor required)
Available in 8-Pin DIP, SOIC-8, widebody packages
Guaranteed performance from -40°C to 85°C
Safety approval
– UL recognized -3750 V rms for 1 minute (5000 V
rms for 1 minute for HCNW22XX) per UL1577
– CSAapproved
– IEC/EN/DIN EN 60747-5-5 approved with VIORM =
630 V peak (HCPL-2211/2212 Option 060 only) and
VIORM = 1414 V peak (HCNW22XX only)
MIL-PRF-38534 hermetic version available
(HCPL-52XX/62XX)
Applications
Isolation of high speed logic systems
Computer-peripheral interfaces
Microprocessor system interfaces
Ground loop elimination
Pulse transformer replacement
High speed line receiver
Power control systems
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
7
1
2
3
45
6
8
NC
ANODE
CATHODE
NC GND
VCC
VO
NC
SHIELD
HCPL-2201/11
HCPL-0201/11
HCNW2201/11
7
1
2
3
45
6
8
NC
ANODE
CATHODE
NC GND
VCC
VO
NC
SHIELD
HCPL-2202/12
7
1
2
3
45
6
8
ANODE 1
CATHODE 1
CATHODE 2
ANODE 2 GND
VCC
VO1
VO2
SHIELD
HCPL-2231/32
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
VO
HIGH
LOW
2
Schematic
HCPL-2201/02/11/12
HCPL-0201/11
HCNW2201/11
IF
SHIELD
VF
VCC
VO
GND
ICC
IO
+
–
2
3
8
5
IF1
SHIELD
VF1
VCC
VO1
ICC
IO1
+
–
1
2
8
6
HCPL-2231/32
SHIELD
VF2
VO2
GND
IO2
–
+
3
4
5
IF2
7
The electrical and switching characteristics of the HCPL-22XX, HCPL-02XX and HCNW22XX are guaranteed from
-40°C to +85°C and a VCC from 4.5 volts to 20 volts. Low IF and wide VCC range allow compati bil ity with TTL, LSTTL,
and CMOS logic and result in lower power consump tion compared to other high speed couplers. Logic signals are
transmitted with a typical propagation delay of 150 ns.
Small- Widebody
Minimum CMR Input 8-Pin DIP (300 Mil) Outline SO-8 (400 Mil) Hermetic
On- Single Dual Single Single Single and
dV/dt Current Channel Channel Channel Channel Dual Channel
(V/μs) V
CM (V) (mA) Package Package Package Package Packages
1,000 50 1.6 HCPL-2200[1,2] HCPL-0201 HCNW2201
HCPL-2201
HCPL-2202
1.8 HCPL-2231
2,500 400 1.6 HCPL-2219[1,2]
5,000[3] 300[3] 1.6 HCPL-2211 HCPL-0211 HCNW2211
HCPL-2212
1.8 HCPL-2232
1,000 50 2.0 HCPL-52XX[2]
HCPL-62XX[2]
Notes:
1. HCPL-2200/2219 devices include output enable/disable function.
2. Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate Avago publications.
3. Minimum CMR of 10 kV/μs with VCM = 1000 V can be achieved with input current, IF, of 5 mA.
Selection Guide
3
Ordering Information
HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211 are UL Recognized
with 3750 Vrms for 1 minute per UL1577.
HCNW2201 and HCNW2211 are UL Recognized with 5000 Vrms for 1 minute per UL1577.
All devices listed above are approved under CSA Component Acceptance Notice #5, File CA 88324.
Part
number
Option
Package
Surface
Mount
Gull
Wing
Tape &
Reel
UL 5000
Vrms/ 1
Minute
rating
IEC/EN/DIN EN
60747-5-5 Quantity
RoHS
Compliant
Non RoHS
Compliant
HCPL-2201
HCPL-2202
HCPL-2211
HCPL-2212
-000E No option
300mil
DIP-8
50 per tube
-300E #300 X X 50 per tube
-500E #500 X X X 1000 per reel
-060E #060 X 50 per tube
-360E #360 X X X 50 per tube
-560E #560 X X X X 1000 per reel
HCPL-2231
HCPL-2232
-000E No option 50 per tube
-300E #300 X X 50 per tube
-500E #500 X X X 1000 per reel
HCPL-0201
HCPL-0211
-000E No option
SO-8
X 100 per tube
-500E #500 X X 1500 per reel
-060E #060 X X 100 per tube
-560E #560 X X X 1500 per reel
HCNW2201
HCNW2211
-000E No option 400mil
Widebody
DIP-8
X X 42 per tube
-300E #300 X X X X 42 per tube
-500E #500 X X X X X 750 per reel
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-2202-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging
with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant.
Example 2:
HCPL-2202 to order product of 300mil DIP package in tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and
RoHS compliant option will use ‘-XXXE‘.
4
Package Outline Drawings
8-Pin DIP Package (HCPL-2201/02/11/12/31/32)
8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/02/11/12/31/32)
1.080 ± 0.320
(0.043 ± 0.013) 2.54 ± 0.25
(0.100 ± 0.010)
0.51 (0.020) MIN.
0.65 (0.025) MAX.
4.70 (0.185) MAX.
2.92 (0.115) MIN.
5° TYP. 0.254 + 0.076
- 0.051
(0.010 + 0.003)
- 0.002)
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
9.65 ± 0.25
(0.380 ± 0.010)
1.78 (0.070) MAX.
1.19 (0.047) MAX.
A XXXXZ
YYWW
DIMENSIONS IN MILLIMETERS AND (INCHES).
5678
4321
OPTION CODE*
UL RECOGNITION
UR
TYPE NUMBER
* MARKING CODE LETTER FOR OPTION NUMBERS
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
3.56 ± 0.13
(0.140 ± 0.005)
EEE P SPECIAL PROGRAM CODELOT ID
DATE CODE
AVAGO
0.635 ± 0.25
(0.025 ± 0.010) 12° NOM.
9.65 ± 0.25
(0.380 ± 0.010)
0.635 ± 0.130
(0.025 ± 0.005)
7.62 ± 0.25
(0.300 ± 0.010)
5
6
7
8
4
3
2
1
9.65 ± 0.25
(0.380 ± 0.010)
6.350 ± 0.25
(0.250 ± 0.010)
1.016 (0.040)
1.27 (0.050)
10.9 (0.430)
2.0 (0.080)
LAND PATTERN RECOMMENDATION
1.080 ± 0.320
(0.043 ± 0.013)
3.56 ± 0.13
(0.140 ± 0.005)
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254 + 0.076
- 0.051
(0.010 + 0.003)
- 0.002)
5
Small-Outline SO-8 Package (HCPL-0201/11)
8-Pin Widebody DIP Package (HCNW2201/11)
XXX
YWW
5678
5.994 ± 0.203
(0.236 ± 0.008)
3.937 ± 0.127
(0.155 ± 0.005)
0.406 ± 0.076
(0.016 ± 0.003) 1.270
(0.050) BSC
5.080 ± 0.127
(0.200 ± 0.005)
3.175 ± 0.127
(0.125 ± 0.005) 1.524
(0.060)
45
q
X 0.432
(0.017)
0.228 ± 0.025
(0.009 ± 0.001)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
0.305
(0.012) MIN.
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
0.203 ± 0.102
(0.008 ± 0.004)
7o
PIN ONE
0 ~ 7
q
*
*
7.49 (0.295)
1.9 (0.075)
0.64 (0.025)
LAND PATTERN RECOMMENDATION
EEE
LOT ID
4321
5
6
7
8
4
3
2
1
11.23 ± 0.15
(0.442 ± 0.006)
1.80 ± 0.15
(0.071 ± 0.006)
5.10
(0.201) MAX.
1.55
(0.061)
MAX.
2.54 (0.100)
TYP. DIMENSIONS IN MILLIMETERS (INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
7
q
TYP. 0.254 + 0.076
- 0.0051
(0.010 + 0.003)
- 0.002)
11.00
(0.433)
9.00 ± 0.15
(0.354 ± 0.006)
MAX.
10.16 (0.400)
TYP.
A
HCNWXXXX
YYWW
DATE CODE
TYPE NUMBER
0.51 (0.021) MIN.
0.40 (0.016)
0.56 (0.022)
3.10 (0.122)
3.90 (0.154)
EEE
LOT ID
6
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11)
1.00 ± 0.15
(0.039 ± 0.006)
7
q
NOM.
12.30 ± 0.30
(0.484 ± 0.012)
0.75 ± 0.25
(0.030 ± 0.010)
11.00
(0.433)
5
6
7
8
4
3
2
1
11.23 ± 0.15
(0.442 ± 0.006)
9.00 ± 0.15
(0.354 ± 0.006)
1.3
(0.051)
13.56
(0.534)
2.29
(0.09)
LAND PATTERN RECOMMENDATION
1.80 ± 0.15
(0.071 ± 0.006)
4.00
(0.158) MAX.
1.55
(0.061)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254 + 0.076
- 0.0051
(0.010 + 0.003)
- 0.002)
MAX.
7
Regulatory Information
The HCPL-22XX/02XX and HCNW22XX have been approved by the following organizations:
UL Recognized under UL 1577, Component Recognition Program, File E55361.
CSA Approved under CSA Component Acceptance Notice #5, File CA 88324.
IEC/EN/DIN EN 60747-5-5 (Option 060 and HCNW only)
Insulation and Safety Related Speci cations
8-pin DIP Package
Parameter Symbol
8-Pin DIP
(300 Mil)
Value
SO-8
Value
Widebody
(400 Mil)
Value Units Conditions
Minimum External
Air Gap (External
Clearance)
L(101) 7.1 4.9 9.6 mm Measured from input terminals
to output terminals, shortest
distance through air.
Minimum External
Tracking (External
Creepage)
L(102) 7.4 4.8 10.0 mm Measured from input terminals
to output terminals, shortest
distance path along body.
Minimum Internal
Plastic Gap
(Internal Clearance)
0.08 0.08 1.0 mm Through insulation distance,
conductor to conductor, usually
the direct distance between the
photoemitter and photodetector
inside the optocoupler cavity.
Minimum Internal
Tracking (Internal
Creepage)
NA NA 4.0 mm Measured from input terminals
to output terminals, along
internal cavity.
Tracking Resistance
(Comparative
Tracking Index)
CTI 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1
Isolation Group IIIa IIIa IIIa Material Group
(DIN VDE 0110, 1/89, Table 1)
Option 300 - surface mount classi cation is Class A in accordance with CECC 00802.
Solder Re ow Pro le
Recommended re ow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used.
8
IEC/EN/DIN EN 60747-5-5 Insulation Characteristics (Option 060)
Description Symbol Characteristic
HCPL-2201/02/
11/12/31/32
HCPL-
0201/11
Unit
Installation classi cation per DIN VDE 0110, Table 1
for rated mains voltage 150 Vrms
for rated mains voltage 300 Vrms
for rated mains voltage 600 Vrms
I – IV
I – IV
I – IV
I – IV
I – IV
I – III
Climatic Classi cation 0/70/21 0/70/21
Pollution Degree (DIN VDE 0110/39) 2 2
Maximum Working Insulation Voltage VIORM 630 567 Vpeak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC
VPR 1181 1063 Vpeak
Input to Output Test Voltage, Method a*
VIORM x 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial discharge < 5 pC
VPR 1008 907 Vpeak
Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) VIOTM 8000 6000 Vpeak
Safety-limiting values
(Maximum values allowed in the event of a failure, also see Figure 12, Thermal
Derating curve.)
Case Temperature
Input Current
Output Power
TS
IS, INPUT
PS, OUTPUT
175
230
600
150
230
600
°C
mA
mW
Insulation Resistance at TS, VIO = 500 V RS109109
IEC/EN/DIN EN 60747-5-5 Insulation Characteristics
(HCNW22xx Option 060 ONLY)
Description Symbol Characteristic Unit
Installation classi cation per DIN VDE 0110, Table 1
for rated mains voltage 150 Vrms
for rated mains voltage 300 Vrms
for rated mains voltage 600 Vrms
for rated mains voltage 1000 Vrms
I – IV
I – IV
I – IV
I – III
Climatic Classi cation -40/85/21
Pollution Degree (DIN VDE 0110/39) 2
Maximum Working Insulation Voltage VIORM 1414 Vpeak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC
VPR 2651 Vpeak
Input to Output Test Voltage, Method a*
VIORM x 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial discharge < 5 pC
VPR 2262 Vpeak
Highest Allowable Overvoltage* (Transient Overvoltage tini = 60 sec) VIOTM 8000 Vpeak
Safety-limiting values
(Maximum values allowed in the event of a failure, also see Figure 12, Thermal
Derating curve.)
Case Temperature
Input Current
Output Power
TS
IS, INPUT
PS, OUTPUT
150
400
700
°C
mA
mW
Insulation Resistance at TS, VIO = 500 V RS109
* Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
9
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Note
Storage Temperature TS-55 125 °C
Operating Temperature TA-40 85 °C
Average Forward Input Current IF(AVG) 10 mA 1
Peak Transient Input Current
(≤ 1 μs Pulse Width, 300 pps)
(≤ 200 μs Pulse Width, < 1% Duty Cycle)
IF(TRAN) 1.0 A 1
HCNW22XX 40 mA
Reverse Input Voltage VR5V1
HCNW22XX 3
Average Output Current IO25 mA 1
Supply Voltage VCC 020V
Output Voltage VO-0.5 20 V 1
Total Package Power Dissipation PT210 mW 2
HCPL-223X 294
Output Power Dissipation POSee Figure 7 1
Lead Solder Temperature
(Through Hole Parts Only)
260°C for 10 sec.,
1.6 mm below seating plane
HCNW22XX 260°C for 10 sec., up to seating plane
Solder Re ow Temperature Pro le
(Surface Mount Parts Only)
See Package Outline Drawings section
Recommended Operating Conditions
Parameter Symbol Min. Max. Units
Power Supply Voltage VCC 4.5 20 V
Forward Input Current (ON) IF(ON) 1.6* 5 mA
HCPL-223X 1.8†
Forward Input Voltage (OFF) VF(OFF) - 0.8 V
Operating Temperature TA-40 85 °C
Junction Temperature TJ-40 125 °C
Fan Out N 4 TTL Loads
*The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit at least a 20% LED degradation guardband.
†The initial switching threshold is 1.8 mA or less. It is recommended that 2.5 mA be used to permit at least a 20% LED degradation guardband.
10
Electrical Speci cations
-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise speci ed.
All Typicals at TA = 25°C. See Note 7.
Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note Fig
Logic Low Output Voltage VOL 0.5 V IOL = 6.4 mA (4 TTL Loads) 1, 3 1
Logic High Output Voltage VOH 2.4 ** V IOH = -2.6 mA 2, 3, 1
2.7 IOH = -0.4 mA
Output Leakage Current IOHH 100 μA VO = 5.5 V IF = 5 mA 1
500 VO = 20 V
Logic Low Supply ICCL 3.7 6.0 mA VCC = 5.5 V VF = 0 V
4.3 7.0 VCC = 20 V
HCPL-223X 7.4 12.0 VCC = 5.5 V
8.6 14.0 VCC = 20 V
Logic High Supply ICCH 2.4 4.0 mA VCC = 5.5 V IF = 5 mA
2.7 5.0 VCC = 20 V
HCPL-223X 4.8 8.0 VCC = 5.5 V
5.4 10.0 VCC = 20 V
Logic Low Short Circuit IOSL 15 mA VO = VCC = 5.5 V VF = 0 V 1, 3
20 VO = VCC = 20 V VO = GND
Logic High Short Circuit IOSH -10 mA VCC = 5.5 V IF = 5 mA 1, 3
-20 VCC = 20 V
Input Forward Voltage VF 1.5 1.7 V TA = 25°C IF = 5 mA 4 1
1.85
HCNW22XX 1.5 1.82 TA = 25°C
1.95
Input Reverse Breakdown BVR 5 V IR = 10 μA 1
HCNW22XX 3 IR = 100 μA
Input Diode Temperature VF -1.7 mV/°C IF = 5 mA
HCNW22XX TA -1.4
Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 V 1, 4
HCNW22XX 70
*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.
**Typical VOH = VCC - 2.1 V.
(V
OUT < VCC)
Current
Current
Output Current
Voltage
Coe cient
Output Current
IO = Open
IO = Open
11
Parameter Sym. Device Min. Units Test Conditions Fig. Note
Logic High |CMH| HCPL-2201/02 1,000 V/s |VCM| = 50 V VCC = 5 V 10 1, 7
Common Mode HCPL-0201 IF = 1.6 mA† T
A = 25°C
Transient HCPL-2231
Immunity HCNW2201
HCPL-2211/12 5,000 V/s |VCM| = 300 V
HCPL-0211 IF = 1.6 mA‡
HCPL-2232 10,000 V/s |VCM| = 1 kV
HCNW2211 IF = 5.0 mA
Logic Low |CML| HCPL-2201/02 1,000 V/s |VCM| = 50 V VF = 0 V 10 1, 7
Common Mode HCPL-0201 VCC = 5 V
Transient HCPL-2231 TA = 25°C
Immunity HCNW2201
HCPL-2211/12 10,000 V/s |VCM| = 1 kV
HCPL-0211
HCPL-2232
HCNW2211
*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.
†IF = 1.8 mA for HCPL-2231.
‡IF = 1.8 mA for HCPL-2232.
Switching Speci cations (AC)
-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)
* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V.
All Typicals at TA = 25°C, VCC = 5 V, IF(ON) = 3 mA unless otherwise speci ed.
Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note
Propagation Delay Time tPHL 150 ns Without Peaking Capacitor 5, 6 1, 6
160 HCNW22XX
150 300 With Peaking Capacitor
Propagation Delay Time tPLH 110 ns Without Peaking Capacitor 5, 6 1, 6
180 HCNW22XX
90 300 With Peaking Capacitor
Output Rise Time (10-90%) tr 30 ns 5, 9 1
Output Fall Time (90-10%) tf 7 ns 5, 9 1
to Logic Low
Output Level
to Logic High
Output Level
12
Notes:
1. Each channel.
2. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.
3. Duration of output short circuit time should not exceed 10 ms.
4. For single devices, input capacitance is measured between pin 2 and pin 3.
5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of
the output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the
trailing edge of the output pulse.
7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V.
CML is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V.
8. For HCPL-2202/12, VO is on pin 6.
9. Use of a 0.1 F bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage
detection current limit, II-O ≤5 A). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable.
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage
detection current limit, II-O ≤5 A). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-5 Insulation Characteristics Table.
12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.
Package Characteristics
Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note
Input-Output Momentary VISO 3750 V rms RH < 50%, t = 1 min. 5, 10
HCNW22XX 5000 TA = 25°C 5, 11
Input-Output Resistance RI-O 1012 V
I-O = 500 Vdc 5
HCNW22XX 1012 1013 T
A = 25°C
1011 T
A = 100°C
Input-Output Capacitance CI-O 0.6 pF f = 1 MHz, 5
HCNW22XX 0.5 0.6 TA = 25°C, VI-O = 0 Vdc
Input-Input Insulation II-I 0.005 A Relative Humidity = 45%, 12
Leakage Current t = 5 s, VI-I = 500 V
Resistance (Input-Input) RI-I 1011 V
I-I = 500 V 12
Capacitance (Input-Input) CI-I 0.25 pF f = 1 MHz 12
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous volt-
age rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable), your equipment
level safety speci cation or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203
Withstand
Voltage*
13
VOL – LOW LEVEL OUTPUT VOLTAGE – V
-60
0
TA – TEMPERATURE – °C
100
1.0
-20
0.4
20 60-40 0 40 80
0.6
0.8
0.2
VCC = 4.5 V
VF = 0 V
IO = 6.4 mA
0.1
0.3
0.5
0.7
0.9
IOH – HIGH LEVEL OUTPUT CURRENT – mA
-60
-8
TA – TEMPERATURE – °C
100
0
-20
-5
20 60-40 0 40 80
-3
-1
-6
VCC = 4.5 V
IF = 5 mA
-7
-4
-2
VO = 2.7 V
VO = 2.4 V
VO – OUTPUT VOLTAGE – V
0
0
IF – INPUT CURRENT – mA
1.5
5
2
1.00.5
3
1
VCC = 4.5 V
TA = 25 °C
4
IO = 6.4 mA
IO = -2.6 mA
IF – FORWARD CURRENT – mA
1.1
0.001
VF – FORWARD VOLTAGE – V
1.0
1000
1.3
0.01
1.51.2 1.4
0.1
TA = 25 °C
10
100
HCPL-22XX
HCPL-02XX
IF
+
–
VF
IF – FORWARD CURRENT – mA
1.1
0.001
VF – FORWARD VOLTAGE – V
1.0
1000
1.3
0.01
1.51.2 1.4
0.1
10
100
HCNW22XX
IF
+
–
VF
1.6
TA = 25 °C
7
1
45
6
8
HCPL-2201/11
HCPL-02XX
HCNW22XX
GND
VCC
5 V
619 Ω
INPUT
MONITORING
NODE
PULSE GEN.
tr = tf = 5 ns
f = 100 kHz
10 % DUTY
CYCLE
VO = 5 V
ZO = 50
C2 =
15 pF
THE PROBE AND JIG CAPACITANCES
ARE INCLUDED IN C1 AND C2.
OUTPUT VO
MONITORING
NODE
VCC
R1
D1
D2
5 kΩ
D3
D4
2
3
C1 =
120 pF
R1
IF (ON)
2.15 kΩ
1.6 mA
1.10 kΩ
3 mA
681 Ω
5 mA
ALL DIODES ARE 1N916 OR 1N3064.
*
7
45
6
8
HCPL-223X
GND
VCC
5 V
619 Ω
INPUT
MONITORING
NODE
PULSE GEN.
tr = tf = 5 ns
f = 100 kHz
10 % DUTY
CYCLE
VO = 5 V
ZO = 50
C2 =
15 pF
THE PROBE AND JIG CAPACITANCES
ARE INCLUDED IN C1 AND C2.
OUTPUT VO
MONITORING
NODE
VCC
R1
D1
D2
5 kΩ
D3
D4
2
3
C1 =
120 pF
R1
IF (ON)
1.96 kΩ
1.8 mA
1.10 kΩ
3 mA
681 Ω
5 mA
ALL DIODES ARE 1N916 OR 1N3064.
1
*
IF (ON)
50 % IF (ON)
0 mA
tPLH tPHL VOH
1.3 V
VOL
INPUT IF
OUTPUT VO
* 0.1 μF BYPASS — SEE NOTE 9.
Figure 1. Typical logic low output voltage vs.
temperature.
Figure 2. Typical logic high output current vs.
temperature.
Figure 3. Typical output voltage vs. forward
input current.
Figure 4. Typical input diode forward characteristic.
Figure 5. Circuit for tPLH, tPHL, tr, tf.
14
tP – PROPAGATION DELAY – ns
-60
50
TA – TEMPERATURE – °C
100
200
250
-20
100
20 60-40 0 40 80
150
IF (mA)
HCPL-22XX
HCPL-02XX
5
3
1.6*
1.6*
- 5
tPLH
tPHL
VCC = 5.0 V, 20 V
C1 (120 pF) PEAKING
CAPACITOR IS USED.
SEE FIGURE 5.
*IF = 1.8 mA FOR HCPL-223X
DEVICES.
tP – PROPAGATION DELAY – ns
-60
50
TA – TEMPERATURE – °C
100
200
250
-20
100
20 60-40 0 40 80
150
HCNW22XX
VCC = 5.0 V, 20 V
C1 (120 pF) PEAKING CAPACITOR
IS USED. SEE FIGURE 5.
5
3
1.6
1.6,
5
IF (mA)
tPHL
tPLH
PO – MAXIMUM OUTPUT POWER
PER CHANNEL (mW)
0
0
VCC – SUPPLY VOLTAGE – V
20
60
80
5
20
10
TA = 75 °C
15
40
TA = 85 °C
TA =
80°C
VOH – HIGH LEVEL OUTPUT VOLTAGE – V
0
0
VCC – SUPPLY VOLTAGE – V
20
15
20
5
5
10 15
10
TYPICAL
VOH vs. VCC
AT IO = -2.6 mA
TA = 25 °C
tr, tf – RISE, FALL TIME – ns
-60
0
TA – TEMPERATURE – °C
100
100
-20
40
20 60-40 0 40 80
60
80
20
tr
VCC = 5 V
tf
7
1
45
6
8
HCPL-2201/11
HCPL-02XX
HCNW22XX
0.1 μF
BYPASS
OUTPUT VO
MONITORING
NODE
VCC
RIN
2
3
VFF
A
B
–+
VCM
PULSE GENERATOR
–
+
7
45
6
8
HCPL-2231/32
0.1 μF
BYPASS
OUTPUT VO
MONITORING
NODE
VCC
2
3
VFF
A
B
–+
VCM
PULSE GENERATOR
1
+
–
R1
VCM (PEAK)
OUTPUT VO
* SEE NOTE 7, 9.
** IF = 1.8 mA FOR HCPL-2231/32 DEVICES.
0 V
VOH
|VCM|
VOL
VO (MAX.)*
VO (MIN.)*
SWITCH AT A: IF = 1.6 mA**
SWITCH AT B: VF = 0 V
Figure 6. Typical propagation delays vs. temperature. Figure 7. Maximum output power per channel
vs. supply voltage.
Figure 8. Typical logic high output voltage vs.
supply voltage.
Figure 9. Typical rise, fall time vs. temperature.
Figure 10. Test circuit for common mode transient immunity and typical waveforms.
15
INPUT CURRENT THRESHOLD – mA
-60
0.5
TA – TEMPERATURE – °C
100
1.0
-20
0.7
20 60-40 0 40 80
0.8
0.9
0.6
VCC = 5.0 V
VCC = 20 V
HCPL-22XX
HCPL-02XX
IF (ON)
IF (OFF)
IF (ON)
IF (OFF)
INPUT CURRENT THRESHOLD – mA
-60
0.5
TA – TEMPERATURE – °C
100
1.0
-20
0.7
20 60-40 0 40 80
0.8
0.9
0.6
VCC = 5.0 V
VCC = 20 V
HCNW22XX
IF (ON)
IF (OFF)
IF (ON)
IF (OFF)
OUTPUT POWER – PS, INPUT CURRENT – IS
0
0
TS – CASE TEMPERATURE – °C
20050
400
12525 75 100 150
600
800
200
100
300
500
700
PS (mW)
IS (mA)
HCPL-2211/2212 OPTION 060
175
OUTPUT POWER PS, INPUT CURRENT IS
0
0
TS – CASE TEMPERATURE – °C
175
1000
50
400
12525 75 100 150
600
800
200
100
300
500
700
900 PS (mW)
IS (mA)
HCNW22XX
18
27
36
45
1
2
HCPL-2201/11
HCPL-02XX
HCNW22XX
DATA INPUT
TTL OR LSTTL
VCC2 (+5 V)
UP TO 16 LSTTL LOADS
OR 4 TTL LOADS
*
* 0.1 μF BYPASS
1.1 kΩ
VCC1 (+5 V)
DATA OUTPUT
Figure 11. Typical input threshold current vs. temperature.
Figure 12. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-5.
Figure 13a. Recommended LSTTL to LSTTL circuit where 500 ns propagation delay is su cient.
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2016 Avago Technologies. All rights reserved. Obsoletes AV01-0556EN
AV02-0674EN - September 30, 2016
120 pF
18
27
36
45
1
2
HCPL-2201/11
HCPL-02XX
HCNW22XX
DATA INPUT
TTL OR LSTTL
VCC2 (+5 V)
UP TO 16 LSTTL LOADS
OR 4 TTL LOADS
*
* 0.1 μF BYPASS
1.1 kΩ
80 Ω
VCC1 (+5 V)
DATA OUTPUT
120 pF*
18
27
36
45
12
HCPL-2201/11
HCPL-02XX
HCNW22XX
DATA INPUT
TTL OR LSTTL
VCC2
(4.5 TO 20 V)
**0.1 μF BYPASS
1.1 kΩ
80 Ω*
VCC1 (+5 V)
DATA OUTPUT
TOTEM
POLE
OUTPUT
GATE
* 120 pF PEAKING CAPACITOR
MAY BE OMITTED AND 80 Ω
RESISTOR MAY BE SHORTED
WHERE 500 ns PROPAGATION
DELAY IS SUFFICIENT.
VCC
GND
CMOS
VCC2
5 V
10 V
15 V
20 V
RL
1.1 kΩ
2.37 kΩ
3.83 kΩ
5.11 kΩ
RL
18
27
36
45
HCPL-2201/11
HCPL-02XX
HCNW22XX
DATA
INPUT
D1 (1N4150) REQUIRED FOR
ACTIVE PULL-UP DRIVER.
1.1 kΩ
VCC1 (+5 V)
VCC
GND
D1
TTL or
LSTTL
120 pF*
18
27
36
45
HCPL-2201/11
HCPL-02XX
HCNW22XX
DATA INPUT
TTL OR LSTTL
1.1 kΩ
80 Ω*
VCC (+5 V)
OPEN
COLLECTOR
GATE
* 120 pF PEAKING CAPACITOR
MAY BE OMITTED AND 80 Ω
RESISTOR MAY BE SHORTED
WHERE 500 ns PROPAGATION
DELAY IS SUFFICIENT.
VCC
GND
4.7 kΩ
Figure 16. Series LED drive with open collector gate
(4.7 k resistor shunts IOH from the LED).
Figure 14. LSTTL to CMOS interface circuit.
Figure 15. Alternative LED drive circuit.
Figure 13b. Recommended LSTTL to LSTTL circuit for applications requiring a maximum allowable propagation delay of 300 ns.
