544M-01LF - Integrated Device Technology

DATASHEET

CLOCK DIVIDER ICS544-01

IDT®

CLOCK DIVIDER 1

ICS544-01 REV B 051810

Description

The ICS544-01 is crystal oscillator module IC with

divide by 512 frequency output. It employs a 16.777216

MHz fundamental frequency crystal source oscillator to

generate 32.768 kHz output crystal oscillator output. In

addition a divide by 256, 64 and 32 options are also

provided through select pins. The chip has an OE pin

that tri-states the output and stops the oscillator circuits.

The ICS544-01 is a member of IDT’s ClockBlocksTM

family of clock building blocks. See the ICS541 and

ICS542 for other clock dividers, and the ICS501, 502,

511, 512, and 525 for clock multipliers.

Features

•Packaged in 8-pin SOIC

•Pb-free package

•IDT’s lowest cost clock divider

•Easy to use with other generators and buffers

•Input crystal at 16.777216MHz

•Output clock duty cycle of 45/55

•Output Enable

•Advanced, low-power CMOS process

•Operating voltage of 2.25 V to 3.6 V

•Does not degrade phase noise - no PLL

•Available in industrial temperature range

Block Diagram

Divider and

Selection

Circuitry

/32, /64

/256, /512,

CLK1

GND

VDD

16.777216MHz

crystal input

Optional tuning

capacitors

S 1 , S 0 (1 :0 )

ICS544-01

CLOCK DIVIDER CLOCK DIVIDER

IDT®

CLOCK DIVIDER 2

ICS544-01 REV B 051810

Pin Assignment

8-pin (150 mil) SOIC

Clock Divider Table

0 = connect directly to ground

1 = connect directly to VDD

Pin Descriptions

External Components

Series Termination Resistor

On chip capacitors

connected from pins X1 to ground and X2 to ground to

optimize the initial accuracy. The value (in pf) of these

crystal caps equal (CL-12)*2 in this equation,

CL=crystal load capacitance in pf. For example, for a

crystal with a 16 pF load cap, each external crystal cap

would be 8 pF. [(16-12)x2]=8.

Decoupling Capacitor

As with any high-performance mixed-signal IC, the

ICS544-01 must be isolated from system power supply

noise to perform optimally.

A decoupling capacitor of 0.01µF must be connected

between VDD and the PCB ground plane.

X1/ICLK

GND

VDD

CLK

S11

S1 S0 CLK

0 0 Input/32

0 1 Input/64

10 Input/256

11 Input/512

Number

Name

Type Pin Description

1 X1/ICLK XI Crystal input.

2 X2 Xo Connect to crystal for crystal input and leave open for clock input.

3 GND Power Connect to ground.

4 S0 Input Select 0 for output clock. Connect to GND or VDD, per divider table above.

Internal pull-up resistor.

5 CLK Output Clock output per table above. Internal Pull down resistor.

6 OE Input Output Enable.Tri-states output clock when low. Also shuts down the oscillator

circuit. Internal pull-up resistor. OE=1 normal operation.

7 VDD Power Connect to 2.25 V to 3.6 V.

8 S1 Input Select 1 for output clock. Connect to GND or VDD, per divider table above.

Internal pull-up resistor.

ICS544-01

CLOCK DIVIDER CLOCK DIVIDER

IDT®

CLOCK DIVIDER 3

ICS544-01 REV B 051810

PCB Layout Recommendations

For optimum device performance and lowest output

phase noise, the following guidelines should be

observed.

1) The 0.01µF decoupling capacitor should be mounted

on the component side of the board as close to the VDD

pin as possible. No vias should be used between

decoupling capacitor and VDD pin. The PCB trace to

VDD pin should be kept as short as possible, as should

the PCB trace to the ground via. Distance of the ferrite

bead and bulk decoupling from the device is less

critical.

2) To minimize EMI, the 33Ω series termination resistor

(if needed) should be placed close to the clock output.

3) An optimum layout is one with all components on the

same side of the board, minimizing vias through other

signal layers (the ferrite bead and bulk decoupling

capacitor can be mounted on the back). Other signal

traces should be routed away from the ICS544-01. This

includes signal traces just underneath the device, or on

layers adjacent to the ground plane layer used by the

device.

Absolute Maximum Ratings

Stresses above the ratings listed below can cause permanent damage to the ICS544-01. These ratings,

which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of

the device at these or any other conditions above those indicated in the operational sections of the

specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can

affect product reliability. Electrical parameters are guaranteed only over the recommended operating

temperature range.

Recommended Operation Conditions

Item Rating

Supply Voltage, VDD 7 V

All Inputs and Outputs -0.5 V to VDD+0.5 V

Ambient Operating Temperature (commercial) 0 to +70°C

Ambient Operating Temperature (industrial) -40 to +85°C

Storage Temperature -65 to +150°C

Junction Temperature 125°C

Soldering Temperature 260°C

Parameter Min. Typ. Max. Units

Ambient Operating Temperature (commercial) 0 +70 °C

Ambient Operating Temperature (industrial) -40 +85 °C

Power Supply Voltage (measured in respect to GND) 2.25 3.6 V

ICS544-01

CLOCK DIVIDER CLOCK DIVIDER

IDT®

CLOCK DIVIDER 4

ICS544-01 REV B 051810

DC Electrical Characteristics

Unless stated otherwise, VDD = 2.25 V to 3.6 V, CL=15pF ±5%, Ambient Temperature -40°C to +85°C

AC Electrical Characteristics

Unless stated otherwise, VDD = 2.25 V to 3.6 V±5%, CL=15pF ±5%, Ambient Temp -40°C to +85°C

Thermal Characteristics

Parameter Symbol Conditions Min. Typ. Max. Units

Operating Voltage VDD 2.25 3.6 V

Input High Voltage VIH S0, S1, OE, ICLK 0.7VDD V

Input Low Voltage VIL S0, S1, OE, ICLK 0.3VDD V

Output High Voltage VOH IOH = -2 mA VDD-0.4 VDD-0.15 V

Output Low Voltage VOL IOL = 2 mA 0.15 0.4 V

Operating Supply Current IDD VDD =2.25 V - 2.75 V 0.3 0.6 mA

Operating Supply Current IDD VDD= 2.75 V - 3.6 V 0.5 1 mA

Standby Current ISB OE=0 10 ua

Short Circuit Current IOS ±40 mA

Input Capacitance CIN S0, S1, OE 4 pF

Nominal Output Impedance ZOat VDD/2 20 Ω

Internal Pull-up Resistor Rpup OE, S1, S0 420 kΩ

Parameter Symbol Conditions Min. Typ. Max. Units

Input Frequency, clock input VDD = 3.3 V 0 16.777216 MHz

Output Rise Time tOR 0.1VDD to 0.9VDD 0.2 1 μs

Output Fall Time tOF 0.9VDD to 0.1VDD 0.2 1 μs

Duty Cycle at VDD/2 45 49 to 51 55 %

Output Enable Delay Time tOE OE going high to CLK

output valid

2μs

Output Disable Delay Time tOD OE going low to CLK

output invalid

2μs

Parameter Symbol Conditions Min. Typ. Max. Units

Thermal Resistance Junction to

Ambient

θJA Still air 150 °C/W

θJA 1 m/s air flow 140 °C/W

θJA 3 m/s air flow 120 °C/W

Thermal Resistance Junction to Case θJC 40 °C/W

ICS544-01

CLOCK DIVIDER CLOCK DIVIDER

IDT®

CLOCK DIVIDER 5

ICS544-01 REV B 051810

Marking Diagram (ICS554M-01LF) Marking Diagram (ICS554MI-01LF)

Notes:

1. ###### is the lot number.

2. YYWW is the last two digits of the year and week that the part was assembled.

3. “L” or “LF” denotes Pb (lead) free package.

4. “I” denotes industrial temperature range.

5. Bottom Marking: (origin)

Origin = country of origin if not USA.

554M01LF

######

YYWW

554MI01L

######

YYWW

ICS544-01

CLOCK DIVIDER CLOCK DIVIDER

IDT®

CLOCK DIVIDER 6

ICS544-01 REV B 051810

Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body)

Package dimensions are kept current with JEDEC Publication No. 95

Ordering Information

"LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.

While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT)

assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result

from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial

applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary

environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any

circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or

critical medical instruments.

Part / Order Number Marking Shipping Packaging Package Temperature

544M-01LF 544M01LF Tubes 8-pin SOIC 0 to +70° C

544M-01LFT 544M01LF Tape and Reel 8-pin SOIC 0 to +70° C

544MI-01LF 544MI01L Tubes 8-pin SOIC -40 to +85° C

544MI-01LFT 544MI01L Tape and Reel 8-pin SOIC -40 to +85° C

INDEX

AREA

1 2

SEATING

PLANE

- C -

.10 (.004) C

h x 45

Millimeters Inches

Symbol Min Max Min Max

A 1.35 1.75 .0532 .0688

A1 0.10 0.25 .0040 .0098

B 0.33 0.51 .013 .020

C 0.19 0.25 .0075 .0098

D 4.80 5.00 .1890 .1968

E 3.80 4.00 .1497 .1574

e 1.27 BASIC 0.050 BASIC

H 5.80 6.20 .2284 .2440

h 0.25 0.50 .010 .020

L 0.40 1.27 .016 .050

α0°8°0°8°

Device Technology, Inc. Ac celerated Thinking is a s ervice mark of Integrated Devi ce Technology, Inc. All other brands, product names and marks are or may be trademarks or

registered trademarks used to identify products or services of their respective owners.

Printed in USA

Corporate Headquarters

Integrated Device Technology, Inc.

www.idt.com

For Sales

800-345-7015

408-284-8200

Fax: 408-284-2775

For Tech Support

www.idt.com/go/clockhelp

Innovate with IDT and accelerate your future networks. Contact:

www.IDT.com

ICS544-01

CLOCK DIVIDER CLOCK DIVIDER