ispGALTM22V10 Device Datasheet June 2010 All Devices Discontinued! Product Change Notifications (PCNs) have been issued to discontinue all devices in this data sheet. The original datasheet pages have not been modified and do not reflect those changes. Please refer to the table below for reference PCN and current product status. Product Line ispGAL22V10C Ordering Part Number ispGAL22V10C-7LJ ispGAL22V10C-7LJN ispGAL22V10C-10LJ ispGAL22V10C-10LJN ispGAL22V10C-15LJ ispGAL22V10C-15LJN ispGAL22V10C-15LJI ispGAL22V10C-7LK ispGAL22V10C-10LK ispGAL22V10C-15LK ispGAL22V10C-15LKI Product Status Reference PCN PCN#06-07 Discontinued PCN#09-10 5555 N.E. Moore Ct. z Hillsboro, Oregon 97124-6421 z Phone (503) 268-8000 z FAX (503) 268-8347 Internet: http://www.latticesemi.com ispGAL22V10 ree Lead-Fage P a c k ns Optio le! b Availa Features In-System Programmable E2CMOS PLD Generic Array LogicTM Functional Block Diagram * IN-SYSTEM PROGRAMMABLETM (5-V ONLY) -- 4-Wire Serial Programming Interface -- Minimum 10,000 Program/Erase Cycles -- Built-in Pull-Down on SDI Pin Eliminates Discrete Resistor on Board (ispGAL22V10C Only) RESET I/CLK 8 OLMC I/O/Q OLMC I/O/Q I 10 * HIGH PERFORMANCE E2CMOS(R) TECHNOLOGY -- 7.5 ns Maximum Propagation Delay -- Fmax = 111 MHz -- 5 ns Maximum from Clock Input to Data Output -- UltraMOS(R) Advanced CMOS Technology A D LL IS C DE O N VIC TI N ES U ED I 12 PROGRAMMABLE AND-ARRAY (132X44) I I * ACTIVE PULL-UPS ON ALL LOGIC INPUT AND I/O PINS * COMPATIBLE WITH STANDARD 22V10 DEVICES -- Fully Function/Fuse-Map/Parametric Compatible with Bipolar and CMOS 22V10 Devices I I * E2 CELL TECHNOLOGY -- In-System Programmable Logic -- 100% Tested/100% Yields -- High Speed Electrical Erasure (<100ms) -- 20 Year Data Retention I I * TEN OUTPUT LOGIC MACROCELLS -- Maximum Flexibility for Complex Logic Designs * APPLICATIONS INCLUDE: -- DMA Control -- State Machine Control -- High Speed Graphics Processing -- Software-Driven Hardware Configuration OLMC I/O/Q OLMC I/O/Q OLMC I/O/Q OLMC I/O/Q OLMC I/O/Q OLMC I/O/Q OLMC I/O/Q OLMC I/O/Q 14 16 16 14 12 I 10 I I SDO SDI MODE SCLK * ELECTRONIC SIGNATURE FOR IDENTIFICATION 8 PROGRAMMING LOGIC PRESET * LEAD-FREE PACKAGE OPTIONS Description Pin Configuration The ispGAL22V10, at 7.5ns maximum propagation delay time, combines a high performance CMOS process with Electrically Erasable (E2) floating gate technology to provide the industry's first insystem programmable 22V10 device. E2 technology offers high speed (<100ms) erase times, providing the ability to reprogram or reconfigure the device quickly and efficiently. The generic architecture provides maximum design flexibility by allowing the Output Logic Macrocell (OLMC) to be configured by the user. The ispGAL22V10 is fully function/fuse map/parametric compatible with standard bipolar and CMOS 22V10 devices. The standard PLCC package provides the same functional pinout as the standard 22V10 PLCC package with No-Connect pins being used for the ISP interface signals. 28 I/O/Q Vcc 2 SSOP I/O/Q SCLK I 4 I I/CLK I PLCC 26 5 25 7 23 I I I/O/Q ispGAL22V10 MODE 9 21 I I/O/Q I/O/Q 18 19 16 I/O/Q SCLK I/CLK I I I I I MODE I I I I I GND 1 28 7 ispGAL 22V10 22 Top View 14 15 Vcc I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q SDO I/O/Q I/O/Q I/O/Q I/O/Q I/O/Q I SDI I/O/Q I/O/Q SDI I 14 GND I 11 12 I I Unique test circuitry and reprogrammable cells allow complete AC, DC, and functional testing during manufacture. As a result, Lattice Semiconductor delivers 100% field programmability and functionality of all GAL products. In addition, 10,000 erase/write cycles and data retention in excess of 20 years are specified. I/O/Q SDO Top View I I/O/Q Copyright (c) 2004 Lattice Semiconductor Corp. All brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. LATTICE SEMICONDUCTOR CORP., 5555 Northeast Moore Ct., Hillsboro, Oregon 97124, U.S.A. Tel. (503) 268-8000; 1-800-LATTICE; FAX (503) 268-8556; http://www.latticesemi.com isp22v10_04 1 August 2004 Specifications ispGAL22V10 Ordering Information Conventional Packaging Commercial Grade Specifications Tpd (ns) 7.5 Tsu (ns) 6.5 10 Tco (ns) Icc (mA) 5 7 140 7 140 Ordering # Package 1 28-Lead PLCC ispGAL22V10C-7LK 28-Lead SSOP ispGAL22V10C-10LJ 28-Lead PLCC ispGAL22V10C-7LJ 28-Lead SSOP A D LL IS C DE O N VIC TI N ES U ED ispGAL22V10C-10LK 15 10 8 140 ispGAL22V10C-15LJ 28-Lead PLCC ispGAL22V10C-15LK 28-Lead SSOP Industrial Grade Specifications Tpd (ns) Tsu (ns) Tco (ns) Icc (mA) 15 10 8 165 Ordering # Package ispGAL22V10C-15LJI 28-Lead PLCC ispGAL22V10C-15LKI 28-Lead SSOP Lead-Free Packaging Commercial Grade Specifications Tpd (ns) Tsu (ns) Tco (ns) Icc (mA) Ordering # 1 Package 7.5 6.5 5 140 ispGAL22V10C-7LJN 10 7 7 140 ispGAL22V10C-10LJN Lead-Free 28-Lead PLCC 15 10 8 140 ispGAL22V10C-15LJN Lead-Free 28-Lead PLCC Lead-Free 28-Lead PLCC 1. Discontinued per PCN #06-07. Contact Rochester Electronics for available inventory. Part Number Description XXXXXXXX _ XX X XX X ispGAL22V10C Device Name Grade Speed (ns) L = Low Power Power Blank = Commercial I = Industrial Package J = PLCC JN = Lead-Free PLCC K = SSOP 2 Specifications ispGAL22V10 Output Logic Macrocell (OLMC) The ispGAL22V10 has a variable number of product terms per OLMC. Of the ten available OLMCs, two OLMCs have access to eight product terms (pins 17 and 27), two have ten product terms (pins 18 and 26), two have twelve product terms (pins 19 and 25), two have fourteen product terms (pins 20 and 24), and two OLMCs have sixteen product terms (pins 21 and 23). In addition to the product terms available for logic, each OLMC has an additional product-term dedicated to output enable control. The ispGAL22V10 has a product term for Asynchronous Reset (AR) and a product term for Synchronous Preset (SP). These two product terms are common to all registered OLMCs. The Asynchronous Reset sets all registers to zero any time this dedicated product term is asserted. The Synchronous Preset sets all registers to a logic one on the rising edge of the next clock pulse after this product term is asserted. NOTE: The AR and SP product terms will force the Q output of the flip-flop into the same state regardless of the polarity of the output. Therefore, a reset operation, which sets the register output to a zero, may result in either a high or low at the output pin, depending on the pin polarity chosen. A D LL IS C DE O N VIC TI N ES U ED The output polarity of each OLMC can be individually programmed to be true or inverting, in either combinatorial or registered mode. This allows each output to be individually configured as either active high or active low. A R D 4 TO 1 MUX Q CLK Q SP 2 TO 1 MUX ispGAL22V10 OUTPUT LOGIC MACROCELL (OLMC) Output Logic Macrocell Configurations NOTE: In registered mode, the feedback is from the /Q output of the register, and not from the pin; therefore, a pin defined as registered is an output only, and cannot be used for dynamic I/O, as can the combinatorial pins. Each of the Macrocells of the ispGAL22V10 has two primary functional modes: registered, and combinatorial I/O. The modes and the output polarity are set by two bits (SO and S1), which are normally controlled by the logic compiler. Each of these two primary modes, and the bit settings required to enable them, are described below and on the following page. COMBINATORIAL I/O In combinatorial mode the pin associated with an individual OLMC is driven by the output of the sum term gate. Logic polarity of the output signal at the pin may be selected by specifying that the output buffer drive either true (active high) or inverted (active low). Output tri-state control is available as an individual product-term for each output, and may be individually set by the compiler as either "on" (dedicated output), "off" (dedicated input), or "product-term driven" (dynamic I/O). Feedback into the AND array is from the pin side of the output enable buffer. Both polarities (true and inverted) of the pin are fed back into the AND array. REGISTERED In registered mode the output pin associated with an individual OLMC is driven by the Q output of that OLMC's D-type flip-flop. Logic polarity of the output signal at the pin may be selected by specifying that the output buffer drive either true (active high) or inverted (active low). Output tri-state control is available as an individual product-term for each OLMC, and can therefore be defined by a logic equation. The D flip-flop's /Q output is fed back into the AND array, with both the true and complement of the feedback available as inputs to the AND array. 3 Specifications ispGAL22V10 Registered Mode AR AR Q Q D A D LL IS C DE O N VIC TI N ES U ED D CLK Q CLK SP Q SP ACTIVE LOW ACTIVE HIGH S0 = 0 S1 = 0 S0 = 1 S1 = 0 Combinatorial Mode ACTIVE LOW ACTIVE HIGH S0 = 0 S1 = 1 S0 = 1 S1 = 1 4 Specifications ispGAL22V10 ispGAL22V10 Logic Diagram/JEDEC Fuse Map PLCC & SSOP Package Pinout 2 0 4 8 12 16 20 24 28 32 36 40 ASYNCHRONOUS RESET (TO ALL REGISTERS) 0000 0044 . . . 0396 8 OLMC S0 5808 S1 5809 0440 . . . . 0880 10 OLMC 26 A D LL IS C DE O N VIC TI N ES U ED S0 5810 S1 5811 27 3 0924 . . . . . 1452 12 OLMC S0 5812 S1 5813 4 1496 . . . . . . 2112 14 OLMC 25 24 S0 5814 S1 5815 5 2156 . . . . . . . 2860 16 OLMC 23 S0 5816 S1 5817 6 2904 . . . . . . . 3608 16 OLMC 21 S0 5818 S1 5819 7 3652 . . . . . . 4268 14 OLMC 20 S0 5820 S1 5821 9 4312 . . . . . 4840 12 OLMC S0 5822 S1 5823 10 4884 . . . . 5324 10 OLMC S0 5824 S1 5825 11 5368 . . . 5720 8 OLMC S0 5826 S1 5827 12 SYNCHRONOUS PRESET (TO ALL REGISTERS) 5764 13 5828, 5829 ... Electronic Signature ... 5890, 5891 Byte 7 Byte 6 Byte 5 Byte 4 Byte 3 Byte 2 Byte 1 Byte 0 M S B L S B 5 19 18 17 16 Specifications SpecificationsispGAL22V10C ispGAL22V10 Absolute Maximum Ratings(1) Recommended Operating Conditions Supply voltage VCC ....................................... -0.5 to +7V Commercial Devices: Ambient Temperature (TA) ............................. 0 to +75C Supply voltage (VCC) with Respect to Ground ..................... +4.75 to +5.25V Input voltage applied ........................... -2.5 to VCC +1.0V Off-state output voltage applied .......... -2.5 to VCC +1.0V Storage Temperature ................................. -65 to 150C Ambient Temperature with Power Applied ......................................... -55 to 125C Industrial Devices: Ambient Temperature (TA) ............................ -40 to 85C Supply voltage (VCC) with Respect to Ground ..................... +4.50 to +5.50V A D LL IS C DE O N VIC TI N ES U ED 1. Stresses above those listed under the "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress only ratings and functional operation of the device at these or at any other conditions above those indicated in the operational sections of this specification is not implied (while programming, follow the programming specifications). DC Electrical Characteristics Over Recommended Operating Conditions (Unless Otherwise Specified) SYMBOL VIL VIH IIL MIN. TYP.4 MAX. UNITS Input Low Voltage Vss - 0.5 -- 0.8 V Input High Voltage 2.0 -- Vcc+1 V 0V VIN VIL (MAX.) -- -- -100 A SDI Low Leakage Current 0V VIN VIL (MAX.) -- -- 250 A Input or I/O High Leakage Current 3.5V VIN VCC -- -- 10 A SDI High Leakage Current2 VIN = VOH (MIN.) -- -- 1 mA Output Low Voltage IOL = MAX. Vin = VIL or VIH -- -- 0.5 V Output High Voltage IOH = MAX. Vin = VIL or VIH 2.4 -- -- V Low Level Output Current -- -- 16 mA High Level Output Current -- -- -3.2 mA TA = 25C -30 -- -130 mA L -7/-10/-15 -- 90 140 mA L -15 -- 90 165 mA PARAMETER CONDITION Input or I/O Low Leakage Current1 2 IIH VOL VOH IOL IOH IOS3 Output Short Circuit Current COMMERCIAL ICC Operating Power Supply Current INDUSTRIAL ICC Operating Power Supply Current VCC = 5V VOUT = 0.5V VIL = 0.5V VIH = 3.0V ftoggle = 15MHz Outputs Open VIL = 0.5V VIH = 3.0V ftoggle = 15MHz Outputs Open 1) The leakage current is due to the internal pull-up on all pins (except SDI on ispGAL22V10C). See Input Buffer section for more information. 2) The leakage current is due to the internal pull-down on the SDI pin (ispGAL22V10C only). See Input Buffer section for more information. 3) One output at a time for a maximum duration of one second. Vout = 0.5V was selected to avoid test problems caused by tester ground degradation. Characterized but not 100% tested. 4) Typical values are at Vcc = 5V and TA = 25 C 6 Specifications SpecificationsispGAL22V10C ispGAL22V10 AC Switching Characteristics Over Recommended Operating Conditions PARAMETER COM COM/IND -7 -10 -15 MIN. MAX. MIN. MAX. MIN. MAX. DESCRIPTION UNITS A Input or I/O to Combinatorial Output -- 7.5 -- 10 -- 15 ns A Clock to Output Delay -- 5 -- 7 -- 8 ns -- Clock to Feedback Delay -- 2.5 -- 2.5 -- 2.5 ns -- Setup Time, Input or Feedback before Clock 6.5 -- 7 10 -- ns -- Setup Time, SP before Clock 10 -- 10 -- 10 -- ns -- Hold Time, Input or Feedback after Clock 0 -- 0 -- 0 -- ns A Maximum Clock Frequency with External Feedback, 1/(tsu + tco) 87 -- 71.4 -- 55.5 -- MHz A Maximum Clock Frequency with Internal Feedback, 1/(tsu + tcf) 111 -- 105 -- 80 -- MHz A Maximum Clock Frequency with No Feedback 111 -- 105 -- 83.3 -- MHz -- Clock Pulse Duration, High 4 -- 4 -- 6 -- ns -- Clock Pulse Duration, Low 4 -- 4 -- 6 -- ns B Input or I/O to Output Enabled -- 8 -- 10 -- 15 ns C Input or I/O to Output Disabled -- 8 -- 10 -- 15 ns A Input or I/O to Asynchronous Reset of Register -- 13 -- 13 -- 20 ns -- Asynchronous Reset Pulse Duration 8 -- 8 -- 15 -- ns -- Asynchronous Reset to Clock Recovery Time 8 -- 8 -- 10 -- ns -- Synchronous Preset to Clock Recovery Time 10 -- 10 -- 10 -- ns A D LL IS C DE O N VIC TI N ES U ED tpd tco tcf2 tsu1 tsu2 th TEST COND.1 COM fmax3 twh twl ten tdis tar tarw tarr tspr 1) Refer to Switching Test Conditions section. 2) Calculated from fmax with internal feedback. Refer to fmax Description section. 3) Refer to fmax Description section. Capacitance (TA = 25C, f = 1.0MHz) SYMBOL PARAMETER MAXIMUM* UNITS TEST CONDITIONS CI Input Capacitance 8 pF VCC = 5.0V, VI = 2.0V CI/O I/O Capacitance 8 pF VCC = 5.0V, VI/O = 2.0V *Characterized but not 100% tested. 7 Specifications ispGAL22V10 Switching Waveforms INPUT or I/O FEEDBACK INPUT or I/O FEEDBACK VALID INPUT VALID INPUT ts u t pd COMBINATORIAL OUTPUT th CLK tc o A D LL IS C DE O N VIC TI N ES U ED REGISTERED OUTPUT Combinatorial Output 1 / fm a x (external fdbk) Registered Output INPUT or I/O FEEDBACK tdis ten OUTPUT CLK 1 / fm ax (int ern al fd bk ) Input or I/O to Output Enable/Disable t su tc f REGISTERED FEEDBACK tw l tw h fmax with Feedback CLK 1 / fm a x (w/o fdbk) Clock Width INPUT or I/O FEEDBACK DRIVING SP INPUT or I/O FEEDBACK DRIVING AR tsu th tspr tarw CLK CLK tarr tco REGISTERED OUTPUT REGISTERED OUTPUT tar Asynchronous Reset Synchronous Preset 8 Specifications ispGAL22V10 fmax Descriptions CL K CLK LOGIC ARR AY LOGIC ARRAY R EG I S T E R A D LL IS C DE O N VIC TI N ES U ED REGISTER ts u tc o t cf t pd fmax with External Feedback 1/(tsu+tco) Note: fmax with external feedback is calculated from measured tsu and tco. fmax with Internal Feedback 1/(tsu+tcf) CLK LOGIC ARRAY Note: tcf is a calculated value, derived by subtracting tsu from the period of fmax w/internal feedback (tcf = 1/fmax - tsu). The value of tcf is used primarily when calculating the delay from clocking a register to a combinatorial output (through registered feedback), as shown above. For example, the timing from clock to a combinatorial output is equal to tcf + tpd. REGISTER tsu + th fmax with No Feedback Note: fmax with no feedback may be less than 1/twh + twl. This is to allow for a clock duty cycle of other than 50%. Switching Test Conditions Input Pulse Levels +5V GND to 3.0V Input Rise and Fall Times 3ns 10% - 90% Input Timing Reference Levels 1.5V Output Timing Reference Levels 1.5V Output Load R1 See Figure FROM OUTPUT (O/Q) UNDER TEST 3-state levels are measured 0.5V from steady-state active level. Output Load Conditions (see figure) Test Condition A B C TEST POINT R2 R1 R2 CL 300 390 50pF Active High 390 50pF Active Low 300 390 50pF Active High 390 5pF Active Low 300 390 5pF C L* *C L INCLUDES TEST FIXTURE AND PROBE CAPACITANCE 9 Specifications ispGAL22V10 All necessary programming is done via four TTL level logic interface signals. These four signals are fed into the on-chip programming circuitry where a state machine controls the programming. The interface signals are Serial Data In (SDI), Serial Data Out (SDO), Serial Clock (SCLK) and Mode (MODE) control. For details on the operation of the internal state machine and programming of ispGAL22V10 devices please refer to the ISP Architecture and Programming section in this Data Book. Electronic Signature An electronic signature (ES) is provided in every ispGAL22V10 device. It contains 64 bits of reprogrammable memory that can contain user-defined data. Some uses include user ID codes, revision numbers, or inventory control. The signature data is always available to the user independent of the state of the security cell. Output Register Preload The electronic signature is an additional feature not present in other manufacturers' 22V10 devices. To use the extra feature of the user-programmable electronic signature it is necessary to choose a Lattice Semiconductor 22V10 device type when compiling a set of logic equations. In addition, many device programmers have two separate selections for the device, typically an ispGAL22V10 and a ispGAL22V10-UES (UES = User Electronic Signature) or ispGAL22V10-ES. This allows users to maintain compatibility with existing 22V10 designs, while still having the option to use the GAL device's extra feature. A D LL IS C DE O N VIC TI N ES U ED When testing state machine designs, all possible states and state transitions must be verified in the design, not just those required in the normal machine operations. This is because certain events may occur during system operation that throw the logic into an illegal state (power-up, line voltage glitches, brown-outs, etc.). To test a design for proper treatment of these conditions, a way must be provided to break the feedback paths, and force any desired (i.e., illegal) state into the registers. Then the machine can be sequenced and the outputs tested for correct next state conditions. The JEDEC map for the ispGAL22V10 contains the 64 extra fuses for the electronic signature, for a total of 5892 fuses. However, the ispGAL22V10 device can still be programmed with a standard 22V10 JEDEC map (5828 fuses) with any qualified device programmer. The ispGAL22V10 device includes circuitry that allows each registered output to be synchronously set either high or low. Thus, any present state condition can be forced for test sequencing. If necessary, approved GAL programmers capable of executing test vectors perform output register preload automatically. Security Cell Input Buffers A security cell is provided in every ispGAL22V10 device to prevent unauthorized copying of the array patterns. Once programmed, this cell prevents further read access to the functional bits in the device. This cell can only be erased by re-programming the device, so the original configuration can never be examined once this cell is programmed. The Electronic Signature is always available to the user, regardless of the state of this control cell. ispGAL22V10 devices are designed with TTL level compatible input buffers. These buffers have a characteristically high impedance, and present a much lighter load to the driving logic than bipolar TTL devices. All input and I/O pins (except SDI on the ispGAL22V10C) also have built-in active pull-ups. As a result, floating inputs will float to a TTL high (logic 1). The SDI pin on the ispGAL22V10C has a built-in pull-down to keep the device out of the programming state if the pin is not actively driven. However, Lattice Semiconductor recommends that all unused inputs and tri-stated I/O pins be connected to an adjacent active input, Vcc, or ground. Doing so will tend to improve noise immunity and reduce Icc for the device. (See equivalent input and I/O schematics on the following page.) Latch-Up Protection ispGAL22V10 devices are designed with an on-board charge pump to negatively bias the substrate. The negative bias is of sufficient magnitude to prevent input undershoots from causing the circuitry to latch. Additionally, outputs are designed with nchannel pullups instead of the traditional p-channel pullups to eliminate any possibility of SCR induced latching. Device Programming Typical Input Current The ispGAL22V10 device uses a standard 22V10 JEDEC fusemap file to describe the device programming information. Any third party logic compiler can produce the JEDEC file for this device. Input Current (A) 0 In-System Programmability The ispGAL22V10 device features In-System Programmable technology. By integrating all the high voltage programming circuitry on-chip, programming can be accomplished by simply shifting data into the device. Once the function is programmed, the non-volatile E2CMOS cells will not lose the pattern even when the power is turned off. -20 -40 -60 0 1.0 2.0 3.0 Input Voltage (Volts) 10 4.0 5.0 Specifications ispGAL22V10 Power-Up Reset Vcc (min.) Vcc t su t wl CLK t pr Internal Register Reset to Logic "0" ACTIVE LOW OUTPUT REGISTER Device Pin Reset to Logic "1" ACTIVE HIGH OUTPUT REGISTER Device Pin Reset to Logic "0" A D LL IS C DE O N VIC TI N ES U ED INTERNAL REGISTER Q - OUTPUT Circuitry within the ispGAL22V10 provides a reset signal to all registers during power-up. All internal registers will have their Q outputs set low after a specified time (tpr, 1s MAX). As a result, the state on the registered output pins (if they are enabled) will be either high or low on power-up, depending on the programmed polarity of the output pins. This feature can greatly simplify state machine design by providing a known state on power-up. The timing diagram for power-up is shown below. Because of the asynchronous nature of system power-up, some conditions must be met to provide a valid power-up reset of the ispGAL22V10. First, the Vcc rise must be monotonic. Second, the clock input must be at static TTL level as shown in the diagram during power up. The registers will reset within a maximum of tpr time. As in normal system operation, avoid clocking the device until all input and feedback path setup times have been met. The clock must also meet the minimum pulse width requirements. Input/Output Equivalent Schematics PIN PIN (Vref Typical = 3.2V) Feedback Active Pull-up Circuit (Except SDI on ispGAL22V10C) Vcc Active Pull-up Circuit (Vref Typical = 3.2V) Vcc ESD Protection Circuit Vref Vcc Tri-State Control PIN Vcc Vref Data Output PIN ESD Protection Circuit Pull-down Resistor (SDI on ispGAL22V10C Only) Feedback (To Input Buffer) Input Output 11 Specifications ispGAL22V10 ispGAL22V10C: Typical AC and DC Characteristic Diagrams Normalized Tpd vs Vcc 1.2 1.2 1.1 1 0.9 Normalized Tsu Normalized Tco 1.2 1.1 1 0.9 1.1 1 0.9 A D LL IS C DE O N VIC TI N ES U ED Normalized Tpd Normalized Tsu vs Vcc Normalized Tco vs Vcc 0.8 0.8 0.8 4.50 4.75 5.00 5.25 5.50 4.50 4.75 Supply Voltage (V) 1.2 1.2 1.1 1 0.9 0.8 0.7 5.25 4.50 5.50 -25 0 25 50 75 100 Normalized Tsu vs Temp 1 0.9 0.8 1.2 1.1 1 0.9 0.8 0.7 -55 -25 0 25 50 75 100 Delta Tpd vs # of Outputs Switching 125 -55 -25 0 Delta Tco (ns) 0 -0.25 -0.5 -0.75 -0.25 -0.5 -0.75 -1 -1 3 4 5 6 7 8 9 10 1 Number of Outputs Switching 2 3 4 5 6 7 8 9 10 Number of Outputs Switching Delta Tpd vs Output Loading Delta Tco vs Output Loading 12 10 8 6 Delta Tco (ns) RISE FALL 4 2 10 RISE 8 FALL 6 4 2 0 0 -2 -2 0 50 100 150 200 250 0 300 Output Loading (pF) 50 100 150 200 250 Output Loading (pF) 12 25 50 75 100 Temperature (deg. C) Delta Tco vs # of Outputs Switching 0 Delta Tpd (ns) 1.3 Temperature (deg. C) 2 5.50 1.4 Temperature (deg. C) 1 5.25 Normalized Tco vs Temp 1.1 125 5.00 Supply Voltage (V) 0.7 -55 4.75 Supply Voltage (V) Normalized Tsu 1.3 Normalized Tco 1.3 Delta Tpd(ns) Normalized Tpd Normalized Tpd vs Temp 5.00 300 125 Specifications ispGAL22V10 ispGAL22V10C: Typical AC and DC Characteristic Diagrams Vol vs Iol Voh vs Ioh 3 5 2.5 4.5 4 1.5 1 4.25 Voh (V) 2 Voh (V) Vol (V) Voh vs Ioh 3 2 3.75 1 A D LL IS C DE O N VIC TI N ES U ED 0.5 4 0 0 20.00 40.00 60.00 80.00 100.00 30.00 40.00 50.00 60.00 1.00 2.00 3.00 Ioh(mA) Normalized Icc vs Vcc Normalized Icc vs Temp Normalized Icc vs Freq. 1.3 1.1 1 0.9 0.8 1.1 1 0.9 0.8 0.7 4.75 5.00 5.25 -25 0 25 50 75 100 125 Temperature (deg. C) 0 10 4 20 Iik (mA) 30 3 2 40 50 60 70 1 80 0 90 100 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 Vin (V) 1.00 0.90 -2.00 -1.50 -1.00 Vik (V) 13 -0.50 0 25 50 75 Frequency (MHz) Input Clamp (Vik) Delta Icc vs Vcc 5 1.10 0.80 -55 5.50 4.00 1.20 1.2 Supply Voltage (V) Delta Icc (mA) 0.00 Ioh(mA) Normalized Icc Normalized Icc 10.00 20.00 Iol (mA) 1.2 4.50 3.5 0.00 Normalized Icc 0.00 0.00 100 A D LL IS C DE O N VIC TI N ES U ED Notes 14