SGLS302C − MARCH 2005 − REVISED APRIL 2008
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DQualified for Automotive Applications
DOperation From −40°C to 125°C
DReference Voltage Tolerance at 25°C
− 1%...A Grade
− 0.5% ...B Grade
DTypical Temperature Drift
− 14 mV (Q Temp)
DLow Output Noise
D0.2-Ω Typical Output Impedance
DSink-Current Capability = 1 mA to 100 mA
DAdjustable Output Voltage = Vref to 36 V
description
The TL431 is a three-terminal adjustable shunt
regulator with specified thermal stability over
applicable automotive temperature ranges. The output voltage can be set to any value between Vref
(approximately 2.5 V) and 36 V, with two external resistors (see Figure 17). This device has a typical output
impedance of 0.2 Ω. Active output circuitry provides a sharp turn-on characteristic, making this device an
excellent replacement for Zener diodes in many applications, such as onboard regulation, adjustable power
supplies, and switching power supplies.
Ordering Information{
TAPACKAGE†ORDERABLE
PART NUMBER TOP-SIDE
MARKING
SOT-23-5 (DBV) Reel of 3000 TL431AQDBVRQ1 TACQ
−40°C to 125°C
SOT-23-3 (DBZ) Reel of 3000 TL431BQDBZRQ1 T3FU
−40°C to 125°CSOT-23-5 (DBV) Reel of 3000 TL431QDBVRQ1 T3QU
SOT-23-3 (DBZ) Reel of 3000 TL431AQDBZRQ1 TAQU
†For the most current package and ordering information, see the Package Option Addendum at the end of this
document, or see the TI web site at http://www.ti.com.
‡Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging.
symbol REF
CATHODEANODE
functional block diagram CATHODE
REF
ANODE
+
_
Vref
Copyright 2008, Texas Instruments Incorporated
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerFLEX is a trademark of Texas Instruments.
!"# $"%&! '#(
'"! ! $#!! $# )# # #* "#
'' +,( '"! $!#- '# #!#&, !&"'#
#- && $##(
NC − No internal connection
DBV (SOT-23-5) PACKAGE
(TOP VIEW)
1
2
3
5
4
NC
NC†
CATHODE
ANODE
REF
† Pin 2 is connected internally to ANODE
(die substrate) and should be floating or
connected to ANODE.
TL431, TL431A, TL431B
DBZ (SOT-23-5) PACKAGE
(TOP VIEW)
1
2
5
CATHODE
REF ANODE
SGLS302C − MARCH 2005 − REVISED APRIL 2008
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
equivalent schematic{
ANODE
REF
CATHODE
2.4 kΩ7.2 kΩ
3.28 kΩ
20 pF
4 kΩ
1 kΩ
800 Ω
800 Ω800 Ω
20 pF
150 Ω
10 kΩ
†All component values are nominal.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡
Cathode voltage, VKA (see Note 1) 37 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous cathode current range, IKA −100 mA to 150 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reference input current range −50 µA to 10 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating virtual junction temperature, TJ 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg −65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ESD protection level (see Note 2): HBM (H2) 2.5 kV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CDM (C4) 1 kV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MM (M2) 200 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
‡Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: Voltage values are with respect to the ANODE terminal, unless otherwise noted.
NOTE 2: ESD Protection Level per AEC Q100 Classification
package thermal data (see Note3)
PACKAGE BOARD θJC θJA
SOT-23-5 (DBV) High K, JESD 51-7 131°C/W 206°C/W
SOT-23-3 (DBZ) High K, JESD 51-7 76°C/W 206°C/W
NOTE 3: Maximum power dissipation is a function of T J(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
recommended operating conditions
MIN MAX UNIT
VKA Cathode voltage Vref 36 V
IKA Cathode current 1 100 mA
TAOperating free-air temperature range −40 125 °C
SGLS302C − MARCH 2005 − REVISED APRIL 2008
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating conditions, TA = 25°C (unless otherwise
noted)
PARAMETER
TEST
TEST CONDITIONS
TL431Q
UNIT
PARAMETER
TEST
CIRCUIT
TEST CONDITIONS
MIN TYP MAX
UNIT
Vref Reference voltage 2 VKA = Vref, IKA = 10 mA 2440 2495 2550 mV
VI(dev) Deviation of reference voltage
over full temperature range
(see Figure 1) 2VKA = Vref, IKA = 10 mA,
TA = −40°C to 125°C14 34 mV
D
Vref
Ratio of change in reference voltage
3
IKA = 10 mA
∆VKA = 10 V − Vref −1.4 −2.7
mV
DVref
DV
KA
Ratio of change in reference voltage
to the change in cathode voltage 3IKA = 10 mA ∆VKA = 36 V − 10 V −1 −2
mV
V
Iref Reference current 3 IKA = 10 mA, R1 = 10 kΩ, R2 = ∞2 4 µA
II(dev) Deviation of reference current
over full temperature range
(see Figure 1) 3IKA = 10 mA, R1 = 10 kΩ, R2 = ∞,
TA = −40°C to 125°C0.8 2.5 µA
Imin Minimum cathode current for
regulation 2 VKA = Vref 0.4 1 mA
Ioff Off-state cathode current 4 VKA = 36 V, Vref = 0 0.1 1 µA
|zKA|Dynamic impedance (see Figure 1) 2IKA = 1 mA to 100 mA, VKA = Vref,
f ≤ 1 kHz 0.2 0.5 Ω
electrical characteristics over recommended operating conditions, TA = 25°C (unless otherwise
noted)
PARAMETER
TEST
TEST CONDITIONS
TL431AQ
UNIT
PARAMETER
TEST
CIRCUIT
TEST CONDITIONS
MIN TYP MAX
UNIT
Vref Reference voltage 2 VKA = Vref, IKA = 10 mA 2470 2495 2520 mV
VI(dev) Deviation of reference voltage
over full temperature range
(see Figure 1) 2VKA = Vref, IKA = 10 mA,
TA = −40°C to 125°C14 34 mV
D
Vref
Ratio of change in reference voltage
3
IKA = 10 mA
∆VKA = 10 V − Vref −1.4 −2.7
mV
DVref
DV
KA
Ratio of change in reference voltage
to the change in cathode voltage 3IKA = 10 mA ∆VKA = 36 V − 10 V −1 −2
mV
V
Iref Reference current 3 IKA = 10 mA, R1 = 10 kΩ, R2 = ∞2 4 µA
II(dev) Deviation of reference current
over full temperature range
(see Figure 1) 3IKA = 10 mA, R1 = 10 kΩ, R2 = ∞,
TA = −40°C to 125°C0.8 2.5 µA
Imin Minimum cathode current
for regulation 2 VKA = Vref 0.4 0.7 mA
Ioff Off-state cathode current 4 VKA = 36 V, Vref = 0 0.1 0.5 µA
|zKA|Dynamic impedance (see Figure 1) 2IKA = 1 mA to 100 mA, VKA = Vref,
f ≤ 1 kHz 0.2 0.5 Ω
SGLS302C − MARCH 2005 − REVISED APRIL 2008
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating conditions, TA = 25°C (unless otherwise
noted)
PARAMETER
TEST
TEST CONDITIONS
TL431BQ
UNIT
PARAMETER
TEST
CIRCUIT
TEST CONDITIONS
MIN TYP MAX
UNIT
Vref Reference voltage 2 VKA = Vref, IKA = 10 mA 2483 2495 2507 mV
VI(dev) Deviation of reference voltage
over full temperature range
(see Figure 1) 2VKA = Vref, IKA = 10 mA,
TA = −40°C to 125°C14 34 mV
DV
ref
Ratio of change in reference voltage
3
IKA = 10 mA
∆VKA = 10 V − Vref −1.4 −2.7
mV
DVref
DV
KA
Ratio of change in reference voltage
to the change in cathode voltage 3IKA = 10 mA ∆VKA = 36 V − 10 V −1 −2
mV
V
Iref Reference current 3 IKA = 10 mA, R1 = 10 kΩ, R2 = ∞2 4 µA
II(dev) Deviation of reference current
over full temperature range
(see Figure 1) 3IKA = 10 mA, R1 = 10 kΩ, R2 = ∞,
TA = −40°C to 125°C0.8 2.5 µA
Imin Minimum cathode current
for regulation 2 VKA = Vref 0.4 0.7 mA
Ioff Off-state cathode current 4 VKA = 36 V, Vref = 0 0.1 0.5 µA
|zKA|Dynamic impedance (see Figure 1) 1IKA = 1 mA to 100 mA, VKA = Vref,
f ≤ 1 kHz 0.2 0.5 Ω
The deviation parameters, Vref(dev) and Iref(dev), are defined as the differences between the maximum and minimum
values obtained over the recommended temperature range. The average full-range temperature coefficient of the
reference voltage, αVref, is defined as:
where:
∆TA is the recommended operating free-air temperature range of the device.
can be positive or negative, depending on whether minimum V ref or maximum Vref, respectively, occurs at the
lower temperature.
Example: maximum Vref = 2496 mV at 30°C, minimum Vref = 2492 mV at 0°C, Vref = 2495 mV at 25°C,
∆TA = 70°C for TL431
Because minimum Vref occurs at the lower temperature, the coefficient is positive.
Calculating Dynamic Impedance
The dynamic impedance is defined as:
When the device is operating with two external resistors (see Figure 3), the total dynamic impedance of the circuit
is given by:
Maximum Vref
Minimum Vref
∆TA
VI(dev)
ŤaVrefŤǒppm
°CǓ+ǒVI(dev)
Vref at 25°CǓ 106
DTA
ŤaVrefŤ+ǒ4mV
2495 mVǓ 106
70°C[23 ppm
°C
|zKA|+DVKA
DIKA
|zȀ|+DV
DI[|zKA|ǒ1)R1
R2Ǔ
aVref
Figure 1. Calculating Deviation Parameters and Dynamic Impedance
SGLS302C − MARCH 2005 − REVISED APRIL 2008
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
Vref
Input VKA
IKA
Figure 2. Test Circuit for VKA = Vref
VKA +Vrefǒ1)R1
R2Ǔ)Iref R1
Iref
IKA
VKA
Input
Vref
R1
R2
Figure 3. Test Circuit for VKA > Vref
Ioff
VKA
Input
Figure 4. Test Circuit for Ioff
SGLS302C − MARCH 2005 − REVISED APRIL 2008
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table 1. Graphs
FIGURE
Reference voltage vs Free-air temperature 5
Reference current vs Free-air temperature 6
Cathode current vs Cathode voltage 7, 8
OFF-state cathode current vs Free-air temperature 9
Ratio of delta reference voltage to delta cathode voltage vs Free-air temperature 10
Equivalent input noise voltage vs Frequency 11
Equivalent input noise voltage over a 10-s period 12
Small-signal voltage amplification vs Frequency 13
Reference impedance vs Frequency 14
Pulse response 15
Stability boundary conditions 16
Table 2. Application Circuits
FIGURE
Shunt regulator 17
Single-supply comparator with temperature-compensated threshold 18
Precision high-current series regulator 19
Output control of a three-terminal fixed regulator 20
High-current shunt regulator 21
Crowbar circuit 22
Precision 5-V 1.5-A regulator 23
Efficient 5-V precision regulator 24
PWM converter with reference 25
Voltage monitor 26
Delay timer 27
Precision current limiter 28
Precision constant-current sink 29
SGLS302C − MARCH 2005 − REVISED APRIL 2008
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS{
‡Data is for devices having the indicated value of Vref at IKA = 10 mA,
TA = 25°C. Figure 5
2500
2480
2420
2400
−75 −50 −25 0 25 50 75
2540
2580
REFERENCE VOLTAGE
vs
FREE-AIR TEMPERATURE
2600
100 125
2460
2560
2520
2440
TA − Free-Air Temperature − °C
Vref = 2495 mV‡
Vref = 2440 mV‡
VKA = Vref
IKA = 10 mA Vref = 2550 mV‡
− Reference Voltage − mV
Vref
3
2
1
0
−75 −25 0 50
4
REFERENCE CURRENT
vs
FREE-AIR TEMPERATURE
5
100 125
−50 25 75
TA − Free-Air Temperature − °C
R1 = 10 kΩ
R2 = ∞
IKA = 10 mA
− Reference Current −ref
IAµ
Figure 6
Figure 7
25
0
−50
−75
−100
125
−25
−2 −1 0 1
75
50
100
CATHODE CURRENT
vs
CATHODE VOLTAGE
150
23
VKA − Cathode Voltage − V
VKA = Vref
TA = 25°C
− Cathode Current − mAIKA
Figure 8
400
200
0
−200−1 0 1
600
CATHODE CURRENT
vs
CATHODE VOLTAGE
800
23
VKA = Vref
TA = 25°C
VKA − Cathode Voltage − V
Imin
− Cathode Current −
IKA Aµ
†Data at high and low temperatures is applicable only within the recommended operating free-air temperature ranges of the various devices.
SGLS302C − MARCH 2005 − REVISED APRIL 2008
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS{
Figure 9
1.5
1
0.5
0
−75 −25 0 50
− Off-State Cathode Current −
2
OFF-STATE CATHODE CURRENT
vs
FREE-AIR TEMPERATURE
2.5
100 125
−50 25 75
Ioff Aµ
TA − Free-Air Temperature − °C
VKA = 36 V
Vref = 0
Figure 10
−1.15
−1.25
−1.35
−1.45
−1.05
− 0.95
RATIO OF DELTA REFERENCE VOLTAGE TO
DELTA CATHODE VOLTAGE
vs
FREE-AIR TEMPERATURE
− 0.85
TA − Free-Air Temperature − °C
−75 −25 0 50 100 125−50 25 75
VKA = 3 V to 36 V
− mV/V
∆Vref ∆VKA
/
180
140
120
10010 100 1 k
220
240
f − Frequency − Hz
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
260
10 k 100 k
200
160
− Equivalent Input Noise Voltage − nV/ HzVn
IO = 10 mA
TA = 25°C
Figure 11
†Data at high and low temperatures is applicable only within the recommended operating free-air temperature ranges of the various devices.
SGLS302C − MARCH 2005 − REVISED APRIL 2008
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
19.1 V
VCC
TLE2027
TLE2027
AV = 10 V/mV
VEE
0.1 µF
160 kΩ
820 Ω
(DUT)
TL431
16 Ω
910 Ω2000 µF
1 kΩ
VEE
VCC
1 µF
16 kΩ16 kΩ
1 µF33 kΩ
33 kΩ
AV = 2 V/V
22 µF
500 µF
To
Oscilloscop
e
−1
−2
−4
−5
−6
3
−3
0123456
1
0
2
EQUIVALENT INPUT NOISE VOLTAGE
OVER A 10-S PERIOD
4
78910
5
6
t − Time − s
f = 0.1 to 10 Hz
IKA = 10 mA
TA = 25°C
− Equivalent Input Noise Voltage − µV
Vn
+
−+
−
Figure 12. Test Circuit for Equivalent Input Noise Voltage
SGLS302C − MARCH 2005 − REVISED APRIL 2008
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
1 k 10 k 100 k 1 M 10 M
0
10
20
30
50
60
40
SMALL-SIGNAL VOLTAGE AMPLIFICATION
vs
FREQUENCY
9 µF
GND
Output
232 Ω
8.25 kΩ
IKA
15 kΩ
f − Frequency − Hz
TEST CIRCUIT FOR VOLTAGE AMPLIFICATION
IKA = 10 mA
TA = 25°C
− Small-Signal Voltage Amplification − dBAV
+
−
IKA = 10 mA
TA = 25°C
Figure 13
1 kΩ
50 Ω
GND
Output
IKA
0.1
1 k 10 k 100 k 1 M 10 M
1
f − Frequency − Hz
REFERENCE IMPEDANCE
vs
FREQUENCY
10
100 IKA = 10 mA
TA = 25°C
TEST CIRCUIT FOR REFERENCE IMPEDANCE
− Reference Impedance −
KA
|z | Ω
+
−
Figure 14
SGLS302C − MARCH 2005 − REVISED APRIL 2008
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
3
2
1
0−1 0 1 2 3 4
Input and Output Voltage − V
4
5
PULSE RESPONSE
6
567
Input
Output
TA = 25°C
220 Ω
50 Ω
GND
Output
Pulse
Generator
f = 100 kHz
TEST CIRCUIT FOR PULSE RESPONSE
t − Time − µs
Figure 15
SGLS302C − MARCH 2005 − REVISED APRIL 2008
12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
50
40
10
0
0.001 0.01 0.1 1
70
90
STABILITY BOUNDARY CONDITIONS†
FOR ALL TL431 AND TL431A DEVICES
(EXCEPT FOR SOT23-3, SC-70, AND Q-TEMP DEVICES)
100
10
30
80
60
20
TA = 25°C
B
Stable
Stable
A VKA = Vref
B VKA = 5 V
C VKA = 10 V
D VKA = 15 Vf
CL − Load Capacitance − µF
A
C
D150 Ω
IKA
R1 = 10 kΩ
R2
CL
VBATT
IKA
CLVBATT
150 Ω
TEST CIRCUIT FOR CURVE A
TEST CIRCUIT FOR CURVES B, C, AND D
− Cathode Current − mA
IKA
+
−
+
−
50
40
10
0
0.001 0.01 0.1 1
70
90
STABILITY BOUNDARY CONDITIONS†
FOR ALL TL431B, TL432, SOT-23, SC-70, AND Q-TEMP DEVICES
100
10
30
80
60
20
Stable
A VKA = Vref
B VKA = 5 V
C VKA = 10 V
D VKA = 15 Vf
CL − Load Capacitance − µF
A
C
D
150 Ω
IKA
R1 = 10 kΩ
R2
CL
VBATT
IKA
CLVBATT
150 Ω
TEST CIRCUIT FOR CURVE A
TEST CIRCUIT FOR CURVES B, C, AND D
− Cathode Current − mA
IKA
†The areas under the curves represent conditions that may cause the
device to oscillate. For curves B, C, and D, R2 and V+ were adjusted
to establish the initial VKA and IKA conditions with CL = 0. VBATT and
CL then were adjusted to determine the ranges of stability.
+
−
+
−
B
A
TA = 25°C
Stable
B
Figure 16
SGLS302C − MARCH 2005 − REVISED APRIL 2008
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
R1
0.1%
R2
0.1%
R
(see Note A)
Vref
VO
TL431
VI(BATT)
RETURN
NOTE A: R should provide cathode current ≥1 mA to the TL431 at minimum VI(BATT).
VO+ǒ1)R1
R2ǓVref
Figure 17. Shunt Regulator
VO
TL431
VI(BATT)
VIT ≈2.5 V GND
Input Von ≈2 V
Voff ≈VI(BATT)
Figure 18. Single-Supply Comparator With Temperature-Compensated Threshold
R
(see Note A)
VO
TL431
VI(BATT)
2N222
2N222
4.7 kΩ
R1
0.1%
R2
0.1%
0.01 µF
30 Ω
VO+ǒ1)R1
R2ǓVref
NOTE A: R should provide cathode current ≥1 mA to the TL431 at minimum VI(BATT).
Figure 19. Precision High-Current Series Regulator
SGLS302C − MARCH 2005 − REVISED APRIL 2008
14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
VO
TL431
VI(BATT)
uA7805
IN OUT
Common R1
R2
VO+ǒ1)R1
R2ǓVref
Minimum VO+Vref )5V
Figure 20. Output Control of a Three-Terminal Fixed Regulator
VO
TL431
VI(BATT)
R1
R2
VO+ǒ1)R1
R2ǓVref
Figure 21. High-Current Shunt Regulator
VO
TL431
VI(BATT)
R1
R2
NOTE A: See the stability boundary conditions in Figure 16 to determine allowable values for C.
C
(see Note A)
Figure 22. Crowbar Circuit
SGLS302C − MARCH 2005 − REVISED APRIL 2008
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
VO ≈5 V, 1.5 A
TL431
VI(BATT) LM317
IN OUT
Adjust 243 Ω
0.1%
243 Ω
0.1%
8.2 kΩ
Figure 23. Precision 5-V 1.5-A Regulator
VO ≈5 V
TL431
VI(BATT)
27.4 kΩ
0.1%
Rb
(see Note A)
27.4 kΩ
0.1%
NOTE A: Rb should provide cathode current ≥1 mA to the TL431.
Figure 24. Efficient 5-V Precision Regulator
TL431
12 V
VCC
5 V
6.8 kΩ
10 kΩ
10 kΩ
0.1%
10 kΩ
0.1%
X
Not
Used
Feedback
TL598
+
−
Figure 25. PWM Converter With Reference
SGLS302C − MARCH 2005 − REVISED APRIL 2008
16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
TL431
VI(BATT)
R3
(see Note A)
R1A R4
(see Note A)
R2BR2A
NOTE A: R3 and R4 are selected to provide the desired LED intensity and cathode current ≥1 mA to the TL431 at the available VI(BATT).
R1B Low Limit +ǒ1)R1B
R2BǓVref
High Limit +ǒ1)R1A
R2AǓVref
LED on When Low Limit < VI(BATT) < High Limit
Figure 26. Voltage Monitor
TL431
650 Ω
2 kΩ
C
On
Off
R
12 V
Delay +R C Inǒ12 V
12 V *VrefǓ
Figure 27. Delay Timer
TL431
IO
RCL
0.1%
R1
VI(BATT) Iout +Vref
RCL )IKA
R1 +VI(BATT)
IO
hFE )IKA
Figure 28. Precision Current Limiter
SGLS302C − MARCH 2005 − REVISED APRIL 2008
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
TL431 RS
0.1%
IO
VI(BATT)
IO+Vref
RS
Figure 29. Precision Constant-Current Sink
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
TL431AQDBVRQ1 ACTIVE SOT-23 DBV 5 3000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL431AQDBZRQ1 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL431BQDBZRQ1 ACTIVE SOT-23 DBZ 3 3000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TL431A-Q1, TL431B-Q1 :
•Catalog: TL431A,TL431B
NOTE: Qualified Version Definitions:
•Catalog - TI's standard catalog product
PACKAGE OPTION ADDENDUM
www.ti.com 3-Dec-2009
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and www.ti.com/automotive
Automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions www.ti.com/lprfTI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
