IDT54/74FCT162245T/AT/CT FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER FEATURES: * * * * * * * * * IDT54/74FCT162245T/AT/CT DESCRIPTION: 0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions Typical tSK(o) (Output Skew) < 250ps Low input and output leakage 1A (max.) ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) Balanced Output Drivers: - 24mA (industrial) - 16mA (military) Reduced system switching noise Typical VOLP (Output Ground Bounce) < 0.6V at VCC = 5V, TA = 25C Available in the following packages: - Industrial: SSOP, TSSOP, TVSOP - Military: CERPACK The FCT162245T 16-bit transceiver is built using advanced dual metal CMOS technology. These high-speed, low-power transceivers are ideal for synchronous communication between two buses (A and B). The Direction and Output Enable controls operate these devices as either two independent 8-bit transceivers or one 16-bit transceiver. The direction control pin (xDIR) controls the direction of data flow. The output enable pin (xOE) overrides the direction control and disables both ports. All inputs are designed with hysteresis for improved noise margin. The FCT162245T has balanced output drive with current limiting resistors. This offers low ground bounce, minimal undershoot, and controlled output fall times-reducing the need for external series terminating resistors. The FCT162245T is a plug-in replacement for the FCT16245T and ABT16245 for on-board interface applications. FUNCTIONAL BLOCK DIAGRAM 1 DIR 2 DIR 1 OE 2 OE 1A 1 2A 1 1B 1 2B 1 1A 2 2A 2 1B 2 2B 2 1A 3 2A 3 1B 3 2B 3 1A 4 2A 4 1B 4 2B 4 1A 5 2A 5 1B 5 2B 5 1A 6 2A 6 1B 6 2B 6 1A 7 2A 7 1B 7 2B 7 1A 8 2A 8 1B 8 2B 8 The IDT logo is a registered trademark of Integrated Device Technology, Inc. MILITARY AND INDUSTRIAL TEMPERATURE RANGES JULY 2002 1 (c) 2002 Integrated Device Technology, Inc. DSC-5457/3 IDT54/74FCT162245T/AT/CT FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol Description Max Unit VTERM(2) Terminal Voltage with Respect to GND -0.5 to +7 V 1OE VTERM(3) Terminal Voltage with Respect to GND -0.5 to VCC+0.5 V TSTG Storage Temperature -65 to +150 C IOUT DC Output Current -60 to +120 mA 1DIR 1 48 1B 1 2 47 1A 1 1B 2 3 46 1A 2 GND 4 45 GND 1B 3 5 44 1A 3 1B 4 6 43 1A 4 VCC 7 42 VCC 1B 5 8 41 1A 5 1B 6 9 40 1A 6 Symbol 10 39 GND GND 1B 7 11 38 1B 8 12 37 1A 8 2B 1 13 36 2A 1 2B 2 14 35 2A 2 GND 15 34 GND 2B 3 16 33 2A 3 2B 4 17 32 2A 4 VCC 18 31 VCC 2B 5 19 30 2A 5 2B 6 20 29 2A 6 GND 21 28 GND 2B 7 22 27 2A 7 2B 8 23 26 2A 8 2DIR 24 25 2OE NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. All device terminals except FCT162XXXT AND FCT166XXXT (A-Port) Output and I/O terminals. 3. Output and I/O terminals terminals for FCT162XXXT AND FCT166XXXT (A-Port). CAPACITANCE (TA = +25C, F = 1.0MHz) 1A 7 Parameter(1) Conditions Typ. Max. CIN Input Capacitance VIN = 0V 3.5 6 pF COUT Output Capacitance VOUT = 0V 3.5 8 pF NOTE: 1. This parameter is measured at characterization but not tested. PIN DESCRIPTION Pin Names Description xOE Output Enable Inputs (Active LOW) xDIR Direction Control Input xAx Side A Inputs or 3-State Outputs xBx Side B Inputs or 3-State Outputs FUNCTION TABLE(1) Inputs xOE xDIR L L Bus B Data to Bus A L H Bus A Data to Bus B H X High Z State NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level X = Don't Care Z = High-Impedance SSOP/ TSSOP/ TVSOP/ CERPACK TOP VIEW 2 Outputs Unit IDT54/74FCT162245T/AT/CT FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 5.0V 10%; Military: TA = -55C to +125C, VCC = 5.0V 10% Symbol Test Conditions(1) Parameter Min. Typ.(2) Max. Unit VIH Input HIGH Level Guaranteed Logic HIGH Level 2 -- -- V VIL Input LOW Level Guaranteed Logic LOW Level -- -- 0.8 V IIH Input HIGH Current (Input pins)(5) VCC = Max. -- -- 1 A -- -- 1 -- -- 1 -- -- 1 VO = 2.7V -- -- 1 VO = 0.5V -- -- 1 -- -0.7 -1.2 V -80 -140 -250 mA -- 100 -- mV -- 5 500 A Min. 60 -60 2.4 Typ.(2) 115 -115 3.3 Max. 200 -200 -- Unit mA mA V -- 0.3 0.55 V VI = VCC Input HIGH Current (I/O pins)(5) IIL Input LOW Current (Input pins)(5) VI = GND Input LOW Current (I/O pins)(5) IOZH High Impedance Output Current IOZL (3-State Output pins)(5) VIK Clamp Diode Voltage IOS Short Circuit Current VH Input Hysteresis ICCL ICCH ICCZ Quiescent Power Supply Current VCC = Max. VCC = Min., IIN = -18mA VCC = Max., VO = GND(3) -- VCC = Max. VIN = GND or VCC A A OUTPUT DRIVE CHARACTERISTICS Symbol IODL IODH VOH VOL Parameter Output LOW Current Output HIGH Current Output HIGH Voltage Output LOW Voltage Test Conditions(1) VCC = 5V, VIN = VIH or VIL, VO = 1.5V(3) VCC = 5V, VIN = VIH or VIL, VO = 1.5V(3) VCC = Min IOH = -16mA MIL VIN = VIH or VIL IOH = -24mA IND VCC = Min IOH = 16mA MIL VIN = VIH or VIL IOH = 24mA IND NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25C ambient. 3. Not more than one output should be tested at one time. Duration of the test should not exceed one second. 4. Duration of the condition can not exceed one second. 5. This test limit for this parameter is 5A at TA = -55C. 3 IDT54/74FCT162245T/AT/CT FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES POWER SUPPLY CHARACTERISTICS Test Conditions(1) Min. Typ.(2) Max. Unit -- 0.5 1.5 mA VIN = VCC VIN = GND -- 60 100 A/ MHz VCC = Max. Outputs Open fi = 10MHz VIN = VCC VIN = GND -- 0.6 1.5 mA 50% Duty Cycle xOE = xDIR = GND One Bits Togging VIN = 3.4V VIN = GND -- 0.9 2.3 VCC = Max. Outputs Open fi = 2.5MHz VIN = VCC VIN = GND -- 2.4 4.5(5) 50% Duty Cycle xOE = xDIR = GND Sixteen Bits Togging VIN = 3.4V VIN = GND -- 6.4 16.5(5 Symbol Parameter ICC Quiescent Power Supply Current TTL Inputs HIGH VCC = Max. VIN = 3.4V(3) ICCD Dynamic Power Supply Current(4) VCC = Max. Outputs Open xOE = xDIR = GND One Input Toggling 50% Duty Cycle Total Power Supply Current(6) IC NOTES: 1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25C ambient. 3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested. 6. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fCPNCP/2 + fiNi) ICC = Quiescent Current (ICCL, ICCH and ICCZ) ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) NCP = Number of Clock Inputs at fCP fi = Input Frequency Ni = Number of Inputs at fi SWITCHING CHARACTERISTICS OVER OPERATING RANGE Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tPZH tPZL tPHZ tPLZ tSK(o) Parameter Propagation Delay A to B, B to A Output Enable Time xOE to A or B Output Disable Time xOE to A or B Output Enable Time xDIR to A or B(4) Output Disable Time xDIR to A or B(4) Output Skew(3) Condition(1) CL = 50pF RL = 500 54FCT162445T Mil. Min.(2) Max. 1.5 7.5 54/74FCT162245AT Ind. Mil. Min.(2) Max. Min.(2) Max. 1.5 4.6 1.5 4.9 54/74FCT162245CT Ind. Mil. Min.(2) Max. Min.(2) Max. 1.5 3.5 1.5 4.5 Unit ns 1.5 10 1.5 6.2 1.5 6.5 1.5 4.4 1.5 6.2 ns 1.5 10 1.5 5 1.5 6 1.5 4 1.5 5.2 ns 1.5 10 1.5 6.2 1.5 6.5 1.5 4.8 1.5 6.2 ns 1.5 10 1.5 5 1.5 6 1.5 4 1.5 5.2 ns -- 0.5 -- 0.5 -- 0.5 -- 0.5 -- 0.5 ns NOTES: 1. See test circuit and waveforms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. Skew between any two outputs of the same package switching in the same direction. This parameter is guaranteed by design. 4. This parameter is guaranteed but not tested. 4 IDT54/74FCT162245T/AT/CT FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES TEST CIRCUITS AND WAVEFORMS V CC SWITCH POSITION 7.0V 500 V OUT VIN Pulse Generator 50pF Switch Closed All Other Tests Open DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. D.U.T. RT Test Open Drain Disable Low Enable Low 500 CL Test Circuits for All Waveforms DATA INPUT tH tSU TIMING INPUT ASYNCHRONOUS CONTROL PRESET CLEAR ETC. SYNCHRONOUS CONTROL PRESET CLEAR CLOCK ENABLE ETC. tREM tSU 3V 1.5V 0V 3V 1.5V 0V LOW-HIGH-LOW PULSE 1.5V tW 3V 1.5V 0V HIGH-LOW-HIGH PULSE 1.5V 3V 1.5V 0V tH Pulse Width Set-up, Hold, and Release Times ENABLE SAME PHASE INPUT TRANSITION tPLH tPHL OUTPUT tPLH tPHL OPPOSITE PHASE INPUT TRANSITION 3V 1.5V 0V VOH 1.5V VOL DISABLE 3V CONTROL INPUT tPLZ tPZL OUTPUT NORMALLY LOW 3V 1.5V 0V OUTPUT NORMALLY HIGH Propagation Delay SWITCH CLOSED tPZH SWITCH OPEN 1.5V 0V 3.5V 1.5V 3.5V 0.3V VOL tPHZ 0.3V 1.5V 0V VOH 0V Enable and Disable Times NOTES: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. 2. Pulse Generator for All Pulses: Rate 1.0MHz; tF 2.5ns; tR 2.5ns. 5 IDT54/74FCT162245T/AT/CT FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER MILITARY AND INDUSTRIAL TEMPERATURE RANGES ORDERING INFORMATION FCT IDT XX Temp. Range XXX Family XXXX Device Type X Process XX Package Blank B Industrial MIL-STD-883, Class B PV PA PF Industrial Options Shrink Small Outline Package Thin Shrink Small Outline Package Thin Very Small Outline Package E Military Options CERPACK 16-Bit Buffer/Line Driver 245T 245AT 245CT 162 Double-Density, 5 Volt, Balanced Drive 54 74 - 55C to +125C - 40C to +85C DATA SHEET DOCUMENT HISTORY 3/26/2002 Removed standard speed grade 6/26/2002 Updated as per PDNs Logic-00-07 and Logic-01-04 CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 6 for Tech Support: logichelp@idt.com (408) 654-6459