TLV2422, TLV2422A, TLV2422Y Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER 1997 - REVISED APRIL 2001 D D D D D Output Swing Includes Both Supply Rails Extended Common-Mode Input Voltage Range . . . 0 V to 4.5 V (Min) With 5-V Single Supply No Phase Inversion Low Noise . . . 18 nV/Hz Typ at f = 1 kHz Low Input Offset Voltage 950 V Max at TA = 25C (TLV2422A) D D D D Low Input Bias Current . . . 1 pA Typ Micropower Operation . . . 50 A Per Channel 600- Output Drive Available in Q-Temp Automotive HighRel Automotive Applications Configuration Control / Print Support Qualification to Automotive Standards description Other members in the TLV2422 family are the high-power, TLV2442, and low-power, TLV2432, versions. HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 5 VDD = 5 V VOH - High-Level Output Voltage - V The TLV2422 and TLV2422A are dual low-voltage operational amplifiers from Texas Instruments. The common-mode input voltage range for this device has been extended over the typical CMOS amplifiers making them suitable for a wide range of applications. In addition, the devices do not phase invert when the common-mode input is driven to the supply rails. This satisfies most design requirements without paying a premium for rail-to-rail input performance. They also exhibit rail-to-rail output performance for increased dynamic range in single- or split-supply applications. This family is fully characterized at 3-V and 5-V supplies and is optimized for low-voltage operation. The TLV2422 only requires 50 A of supply current per channel, making it ideal for battery-powered applications. The TLV2422 also has increased output drive over previous rail-to-rail operational amplifiers and can drive 600- loads for telecom applications. TA = -40C 4 TA = 25C 3 2 TA = 85C 1 TA = 125C 0 0 4 8 12 16 20 24 28 32 36 40 IOH - High-Level Output Current - mA Figure 1 The TLV2422, exhibiting high input impedance and low noise, is excellent for small-signal conditioning for high-impedance sources, such as piezoelectric transducers. Because of the micropower dissipation levels and low-voltage operation, these devices work well in hand-held monitoring and remote-sensing applications. In addition, the rail-to-rail output feature with single- or split-supplies makes this family a great choice when interfacing with analog-to-digital converters (ADCs). For precision applications, the TLV2422A is available with a maximum input offset voltage of 950 V. If the design requires single operational amplifiers, see the TI TLV2211/21/31. This is a family of rail-to-rail output operational amplifiers in the SOT-23 package. Their small size and low power consumption, make them ideal for high density, battery-powered equipment. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Advanced LinCMOS is a trademark of Texas Instruments. Copyright 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 TLV2422, TLV2422A, TLV2422Y Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER 1997 - REVISED APRIL 2001 AVAILABLE OPTIONS PACKAGED DEVICES TA VIOmax AT 25C SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (JG) TSSOP (PW) CERAMIC FLAT PACK (U) 0C to 70C 2.5 mV TLV2422CD -- -- TLV2422CPWLE -- - 40C to 85C 950 V 2.5 mV TLV2422AID TLV2422ID -- -- -- -- TLV2422AIPWLE -- -- -- - 40C to 125C 950 V 2.5 mV TLV2422AQD TLV2422QD -- -- -- -- -- -- -- -- - 55C to 125C 950 V 2 mV -- -- TLV2422AMFK TLV2422MFK TLV2422AMJG TLV2422MJG -- -- TLV2422AMU TLV2422MU CHIP FORM (Y) TLV2422Y The D packages are available taped and reeled. Add R suffix to device type (e.g., TLV2422CDR). The PW package is available only left-end taped and reeled. Chips are tested at 25C. D OR JG PACKAGE (TOP VIEW) 1OUT 1IN - 1IN + VDD - /GND 1 8 2 7 3 6 4 5 PW PACKAGE (TOP VIEW) VDD + 2OUT 2IN - 2IN + 1OUT 1IN- 1IN + VDD - / GND 1 2 3 4 8 7 6 5 VDD + 2OUT 2IN - 2IN + NC 1OUT NC VDD+ NC FK PACKAGE (TOP VIEW) 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC 2OUT NC 2IN - NC NC 1OUT 1IN - 1IN + VDD - /GND NC VDD- /GND NC 2IN+ NC NC 1IN - NC 1IN + NC U PACKAGE (TOP VIEW) NC - No internal connection 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 10 2 9 3 8 4 7 5 6 NC VDD + 2OUT 2IN - 2IN + equivalent schematic (each amplifier) COMPONENT COUNT Q22 Q29 Q31 Q34 Q36 Transistors Diodes Resistors Capacitors VB3 69 5 26 6 Q26 Q32 VB2 VB1 VDD+ Q25 Q35 Q33 Q27 Q30 Q37 R10 D1 R9 R3 Q3 R4 R7 Q13 IN- Q1 Q6 Q4 Q8 Q15 Q10 Q18 Q20 IN+ Q7 R5 Q9 C2 VDD-/GND C1 VB3 Q11 Q16 R6 OUT C3 VB2 Q2 Q14 Q5 Q17 Q12 R1 Q21 Q19 R2 R8 VB4 SLOS199C - SEPTEMBER 1997 - REVISED APRIL 2001 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Q23 VB4 3 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS Q24 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDD Input voltage, VI (any input, see Note 1): C and I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.3 V to VDD Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 mA Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Total current into VDD + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Total current out of VDD - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Duration of short-circuit current at (or below) 25C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 85C Q suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 125C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55C to 125C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD - . 2. Differential voltages are at IN+ with respect to IN -. Excessive current flows if input is brought below VDD - - 0.3 V. 3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING TA = 125C POWER RATING D FK JG PW U 725 mW 1375 mW 1050 mW 525 mW 675 mW 5.8 mW/C 11.0 mW/C 8 4 mW/C 8.4 4.2 mW/ mW/C C 5.4 mW/C 464 mW 880 mW 672 mW 336 mW 432 mW 377 mW 715 mW 546 mW 273 mW 350 mW 145 mW 275 mW 210 mW 105 mW 135 mW recommended operating conditions C SUFFIX MIN Supply voltage, VDD 2.7 Input voltage range, VI Common-mode input voltage, VIC VDD - VDD - Operating free-air temperature, TA 0 4 MAX 10 VDD + - 0.8 VDD + - 0.8 70 I SUFFIX MIN 2.7 VDD - VDD - - 40 POST OFFICE BOX 655303 MAX 10 VDD + - 0.8 VDD + - 0.8 85 Q SUFFIX MIN 2.7 VDD - VDD - - 40 * DALLAS, TEXAS 75265 MAX 10 VDD + - 0.8 VDD + - 0.8 125 M SUFFIX MIN 2.7 VDD - VDD - - 55 MAX UNIT 10 V VDD + - 0.8 VDD + - 0.8 V 125 C V TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER TEST CONDITIONS Input offset voltage VIO Temperature coefficient of input offset voltage IIB Input bias current VICR VOL AVD MAX 300 2000 2500 25C to 70C VDD = 2.5 V, RS = 50 VIC = 0, VO = 0 0, 25C 0.003 25C 0.5 25C 1 |VIO| 5 mV mV, Common mode input voltage range Common-mode High-level output voltage IOH = - 500 A Low-level output voltage Large-signal g g differential voltage g amplification 0 to 2.5 Full range 0 to 2.2 RS = 50 IOL = 100 A VIC = 0 0, IOL = 250 A RL = 10 k VIC = 2.5 2 5 V, V VO = 1 V to 2 V RL = 1 M -0.25 to 2.75 25C 2.97 25C 2.75 Full range VIC = 0, 60 150 25C V V/mo 60 150 Full range UNIT V/C 2 Full range IOH = - 100 A VOH TYP Full range Input offset voltage long-term drift (see Note 4) Input offset current TLV2422C MIN 25C VIO IIO TA pA pA V V 2.5 25C 0.05 25C 0.2 Full range V 0.5 25C 6 Full range 3 10 V/mV 25C 700 ri(d) Differential input resistance 25C 1012 ri(c) Common-mode input resistance 25C 1012 ci(c) Common-mode input capacitance f = 10 kHz 25C 8 pF zo Closed-loop output impedance f = 100 kHz, 25C 130 CMRR Common mode rejection ratio Common-mode VIC = 0 to 2.5 V,, VO = 1.5 V,, RS = 50 kSVR Supply voltage rejection ratio (VDD/VIO) Supply-voltage VDD = 2.7 V to 8 V,, VIC = VDD /2, No load IDD Supply current VO = 1 1.5 5V V, AV = 10 No load 25C 70 Full range 70 25C 80 Full range 80 25C Full range 83 dB 95 100 dB 150 175 A Full range is 0C to 70C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR VOH VOL Common-mode input voltage range High-level Hi hl l output t t voltage Low-level L l l output t t voltage TEST CONDITIONS TA TLV2422I MIN 25C MAX 300 2000 Full range VDD = 2.5 V, RS = 50 VIC = 0, VIC = 0 0, 0.003 0.003 V/mo 25C 0.5 60 0.5 150 1 0 to 2.5 60 Full range 0 to 2.2 -0.25 to 2.75 1 2.97 25C 2.75 0 to 2.5 -0.25 to 2.75 0.05 25C 0.2 Full range V V 2.75 0.05 V 0.2 0.5 3 pA 2.5 25C 6 pA 2.97 2.5 25C 60 150 0 to 2.2 25C Full range 60 150 150 25C Full range IOL = 250 A V 25C RS = 50 IOL = 100 A 950 1500 UNIT V/C 25C IOH = - 500 A 300 MAX 2 Full range IOH = - 100 A TYP 2 Full range |VIO| 5 mV mV, MIN 2500 25C to 70C VIC = 0, VO = 0, TLV2422AI TYP 10 0.5 6 10 AVD Large signal Large-signal differential voltage amplification 25C 700 700 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, 25C 130 130 CMRR Common-mode rejection ratio VIC = 0 to 2.5 V,, VO = 1.5 V,, RS = 50 kSVR Supply-voltage rejection ratio (VDD/VIO) VDD = 2.7 V to 8 V,, VIC = VDD /2, No load IDD Supply current VO = 1 1.5 5V V, RL = 10 k VIC = 2.5 2 5 V, V VO = 1 V to 2 V RL = 1 M AV = 10 No load 25C 70 Full range 70 25C 80 Full range 80 3 83 70 V/mV 83 dB 70 95 80 95 dB 25C Full range 80 100 150 175 100 150 175 A Full range is - 40C to 85C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 operating characteristics at specified free-air temperature, VDD = 3 V PARAMETER TEST CONDITIONS VO = 1.5 1 5 V to t 3.5 3 5 V, V CL = 100 pF SR Slew rate at unity gain Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent input noise voltage Peak-to-peak In Equivalent input noise current THD + N Total harmonic distortion plus noise ts m MIN TYP 25C 0.01 0.02 Full range 0.008 25C 100 25C 23 f = 0.1 Hz to 1 Hz 25C 2.7 f = 0.1 Hz to 10 Hz 25C 4 25C 0.6 Maximum output-swing bandwidth VO(PP) = 1 V, RL = 10 k, AV = 1, CL = 100 pF To 0.1% 0 1% Settling time AV = - 1, Step = 0.5 V to 2.5 V,, RL = 10 k, CL = 100 pF RL = 10 k, CL = 100 pF POST OFFICE BOX 655303 fAHz 1.8% 25C 46 kHz 25C 8.3 kHz 86 8.6 01% To 0 0.01% * DALLAS, TEXAS 75265 V 0.25% s 25C Gain margin Full range for the C version is 0C to 70C. Full range for the I version is - 40C to 85C. Referenced to 2.5 V nV/Hz 25C AV = 10 RL = 10 k, UNIT MAX V/s f = 1 kHz AV = 1 Phase margin at unity gain TLV2422C, TLV2422I TLV2422AI f = 10 Hz VO = 0.5 V to 2.5 V, f = 1 kHz kHz, RL = 10 k f = 10 kHz, CL = 100 pF Gain-bandwidth product BOM RL = 10 k, TA 16 25C 62 25C 11 dB 7 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA TLV2422Q, TLV2422M MIN VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR VOH VOL AVD Common-mode input voltage range High-level Hi hl l output t t voltage Low-level L l l output t t voltage Large-signal Large signal differential voltage amplification 25C TYP MAX 300 2000 Full range VDD = 1.5 V, RS = 50 V/mo 25C 0.5 RL = 10 k VIC = 1.5 1 5 V, V VO = 1 V to 2 V RL = 1 M 60 0.5 150 1 25C 0 to 2.5 60 Full range 0 to 2.2 -0.25 to 2.75 1 0 to 2.5 -0.25 to 2.75 V 2.75 2.5 25C 0.05 25C 0.2 Full range 0.05 V 0.2 0.5 2 pA 2.97 2.75 Full range pA V 0 to 2.2 2.5 6 60 300 2.97 25C 60 150 300 25C IOL = 250 A V 0.003 Full range VIC = 0 0, 1800 0.003 25C IOL = 100 A 950 25C RS = 50 VIC = 0, 300 V/C 25C IOH = - 500 A MAX 2 Full range IOH = - 100 A UNIT TYP 2 Full range |VIO| 5 mV mV, MIN 2500 Full range VIC = 0, VO = 0, TLV2422AQ, TLV2422AM 10 0.5 6 10 2 V/mV 25C 700 700 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, 25C 130 130 CMRR Common-mode rejection ratio VIC = VICR min,, VO = 1.5 V,, RS = 50 kSVR Supply-voltage rejection ratio (VDD/VIO) VDD = 2.7 V to 8 V,, VIC = VDD /2, No load IDD Supply current 5V VO = 1 1.5 V, AV = 10 No load 25C 70 Full range 70 25C 80 Full range 80 83 70 83 dB 70 95 80 95 dB 25C Full range 80 100 150 175 100 150 175 A Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 1.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 operating characteristics at specified free-air temperature, VDD = 3 V PARAMETER TEST CONDITIONS VO = 1.1 1 1 V to t 1.9 1 9 V, V CL = 100 pF SR Slew rate at unity gain Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent input noise voltage Peak-to-peak In Equivalent input noise current THD + N Total harmonic distortion plus noise BOM ts m RL = 10 k, TYP 0.01 0.02 Full range 0.008 25C 100 25C 23 f = 0.1 Hz to 1 Hz 25C 2.7 f = 0.1 Hz to 10 Hz 25C 4 25C 0.6 Gain-bandwidth product f = 10 kHz, CL = 100 pF RL = 10 k, Maximum output-swing bandwidth VO(PP) = 1 V, RL = 10 k, AV = 1, CL = 100 pF 0 1% To 0.1% Settling time AV = - 1, Step = 0.5 V to 2.5 V,, RL = 10 k, CL = 100 pF RL = 10 k, CL = 100 pF UNIT MAX V/s f = 1 kHz AV = 1 Gain margin MIN 25C f = 10 Hz VO = 0.5 V to 2.5 V, f = 1 kHz kHz, RL = 10 k Phase margin at unity gain TA TLV2422Q, TLV2422M, TLV2422AQ, TLV2422AM nV/Hz V fAHz 0.25% 25C AV = 10 1.8% 25C 46 kHz 25C 8.3 kHz 86 8.6 s 25C To 0 0.01% 01% 16 25C 62 25C 11 dB Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 1.5 V POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS Input offset voltage VIO Temperature coefficient of input offset voltage IIB Input bias current VICR VOL AVD MAX 300 2000 2500 25C to 70C VDD = 2.5 V, RS = 50 VIC = 0, VO = 0 0, 25C 0.003 25C 0.5 25C 1 |VIO| 5 mV mV, Common mode input voltage range Common-mode High-level output voltage Large-signal g g differential voltage g amplification Full range 0 to 4.2 25C IOH = - 1 mA Low-level output voltage 0 to 4.5 RS = 50 VIC = 2.5 V, IOL = 100 A 5V VIC = 2 2.5 V, IOL = 500 A RL = 10 k VIC = 2.5 2 5 V, V VO = 1 V to 4 V RL = 1 M 60 150 25C V V/mo 60 150 Full range UNIT V/C 2 Full range IOH = - 100 A VOH TYP Full range Input offset voltage long-term drift (see Note 4) Input offset current TLV2422C MIN 25C VIO IIO TA -0.25 to 4.75 pA pA V 4.97 25C 4.5 Full range 4.25 V 4.75 25C 0.04 25C 0.15 Full range V 0.5 25C 8 Full range 5 12 V/mV 25C 1000 ri(d) Differential input resistance 25C 1012 ri(c) Common-mode input resistance 25C 1012 ci(c) Common-mode input capacitance f = 10 kHz 25C 8 pF zo Closed-loop output impedance f = 100 kHz, 25C 130 CMRR Common mode rejection ratio Common-mode VIC = 0 to 4.5 V,, VO = 2.5 V,, RS = 50 kSVR Supply voltage rejection ratio (VDD/VIO) Supply-voltage VDD = 4.4 V to 8 V,, VIC = VDD /2, No load IDD Supply current VO = 2 2.5 5V V, AV = 10 No load 25C 70 Full range 70 25C 80 Full range 80 25C Full range 90 dB 95 100 dB 150 175 A Full range is 0C to 70C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR VOH VOL Common-mode input voltage range High-level Hi hl l output t t voltage Low-level L l l output t t voltage TA TEST CONDITIONS TLV2422I MIN 25C MAX 300 2000 Full range VDD = 2.5 V, RS = 50 VIC = 2.5 V, VIC = 2 2.5 5V V, 0.003 0.003 V/mo 25C 0.5 60 0.5 150 1 60 Full range 0 to 4.2 25C -0.25 to 4.75 1 4.5 Full range 4.25 0 to 4.5 -0.25 to 4.75 4.5 0.15 Full range 0.04 V 0.15 0.5 5 V 4.75 4.25 0.04 8 pA 4.97 4.75 25C 25C pA V 0 to 4.2 25C Full range 60 150 4.97 25C 60 150 150 0 to 4.5 RS = 50 IOL = 500 A V 25C 25C IOL = 100 A 950 1500 UNIT V/C 25C IOH = - 1 mA 300 MAX 2 Full range IOH = - 100 A TYP 2 Full range |VIO| 5 mV mV, MIN 2500 25C to 70C VIC = 0, VO = 0, TLV2422AI TYP 12 0.5 8 12 AVD Large signal Large-signal differential voltage amplification 25C 1000 1000 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, 25C 130 130 CMRR Common-mode rejection ratio VIC = 0 to 4.5 V,, VO = 2.5 V,, RS = 50 kSVR Supply-voltage rejection ratio (VDD/VIO) VDD = 4.4 V to 8 V,, VIC = VDD /2, No load IDD Supply current VO = 2 2.5 5V V, RL = 10 k VIC = 2.5 2 5 V, V VO = 1 V to 4 V RL = 1 M AV = 10 No load 25C 70 Full range 70 25C 80 Full range 80 5 90 70 V/mV 90 dB 70 95 80 95 dB 25C Full range 80 100 150 175 100 150 175 A Full range is - 40C to 85C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER SR TEST CONDITIONS VO = 1 1.5 5 V to 3 3.5 5V V, CL = 100 pF F Slew rate at unity gain Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent input noise voltage Peak-to-peak In Equivalent input noise current THD + N Total harmonic distortion plus noise BOM ts m RL = 10 k, TYP 25C 0.01 0.02 Full range 0 008 0.008 100 25C 18 f = 0.1 Hz to 1 Hz 25C 1.9 f = 0.1 Hz to 10 Hz 25C 2.8 25C 0.6 Gain-bandwidth product f = 10 kHz, CL = 100 pF RL =10 k, Maximum output-swing bandwidth VO(PP) = 2 V, RL = 10 k, AV = 1, CL = 100 pF 0 1% To 0.1% Settling time AV = - 1, Step = 1.5 V to 3.5 V,, RL = 10 k, CL = 100 pF RL = 10 k, CL = 100 pF POST OFFICE BOX 655303 nV/Hz V fAHz 0.24% 25C AV = 10 1.7% 25C 52 kHz 25C 5.3 kHz 85 8.5 s 25C To 0.01% 0 01% * DALLAS, TEXAS 75265 UNIT MAX V/s 25C Full range for the C version is 0C to 70C. Full range for the I version is - 40C to 85C. Referenced to 2.5 V 12 MIN f = 1 kHz AV = 1 Gain margin TLV2422C, TLV2422I TLV2422AI f = 10 Hz VO = 1.5 V to 3.5 V, f = 1 kHz kHz, RL = 10 k Phase margin at unity gain TA 15 5 15.5 25C 66 25C 11 dB TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TA TEST CONDITIONS TLV2422Q, TLV2422M MIN VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR VOH VOL AVD Common-mode input voltage range High-level Hi hl l output t t voltage Low-level L l l output t t voltage Large-signal Large signal differential voltage amplification 25C TYP MAX 300 2000 Full range VDD = 2.5 V, RS = 50 V/mo 25C 0.5 RL = 10 k VIC = 2.5 2 5 V, V VO = 1 V to 4 V RL = 1 M 60 0.5 150 1 25C 0 to 4.5 60 Full range 0 to 4.2 -0.25 to 4.75 1 0 to 4.5 -0.25 to 4.75 V 4.75 4.5 25C 0.04 25C 0.15 Full range 0.04 V 0.15 0.5 3 pA 4.97 4.75 Full range pA V 0 to 4.2 4.5 8 60 300 4.97 25C 60 150 300 25C IOL = 500 A V 0.003 Full range VIC = 2 2.5 5V V, 1800 0.003 25C IOL = 100 A 950 25C RS = 50 VIC = 2.5 V, 300 V/C 25C IOH = - 1 mA MAX 2 Full range IOH = - 100 A UNIT TYP 2 Full range |VIO| 5 mV mV, MIN 2500 Full range VIC = 0, VO = 0, TLV2422AQ, TLV2422AM 12 0.5 8 12 3 V/mV 25C 1000 1000 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, 25C 130 130 CMRR Common-mode rejection ratio VIC = VICR min,, VO = 2.5 V,, RS = 50 kSVR Supply-voltage rejection ratio (VDD/VIO) VDD = 4.4 V to 8 V,, VIC = VDD /2, No load IDD Supply current 5V VO = 2 2.5 V, AV = 10 No load 25C 70 Full range 70 25C 80 Full range 80 90 70 90 dB 70 95 80 95 dB 25C Full range 80 100 150 175 100 150 175 A Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER SR TEST CONDITIONS VO = 1 1.5 5 V to 3 3.5 5V V, CL = 100 pF F Slew rate at unity gain Vn Equivalent input noise voltage VN(PP) Peak to peak equivalent input noise voltage Peak-to-peak In Equivalent input noise current THD + N Total harmonic distortion plus noise RL = 10 k, Full range 0 008 0.008 25C 18 f = 0.1 Hz to 1 Hz 25C 1.9 f = 0.1 Hz to 10 Hz 25C 2.8 25C 0.6 RL =10 k, BOM Maximum output-swing bandwidth VO(PP) = 2 V, RL = 10 k, AV = 1, CL = 100 pF Settling time AV = - 1, Step = 1.5 V to 3.5 V,, RL = 10 k, CL = 100 pF 0 1% To 0.1% ts RL = 10 k, CL = 100 pF POST OFFICE BOX 655303 nV/Hz V fAHz 0.24% 1.7% 25C 52 kHz 25C 5.3 kHz 85 8.5 s 25C To 0.01% 0 01% * DALLAS, TEXAS 75265 MAX 25C AV = 10 Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 2.5 V UNIT V/s f = 1 kHz f = 10 kHz, CL = 100 pF 14 0.02 100 Gain-bandwidth product Gain margin TYP 0.01 25C AV = 1 Phase margin at unity gain MIN 25C f = 10 Hz VO = 1.5 V to 3.5 V, f = 1 kHz kHz, RL = 10 k m TA TLV2422Q, TLV2422M, TLV2422AQ, TLV2422AM 15 5 15.5 25C 66 25C 11 dB TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO Input offset voltage Distribution vs Common-mode input voltage 2,3 , 4,5 VIO IIB/IIO Input offset voltage temperature coefficient Distribution 6,7 Input bias and input offset currents vs Free-air temperature VOH VOL High-level output voltage vs High-level output current 9,11 Low-level output voltage vs Low-level output current 10,12 VO(PP) Maximum peak-to-peak output voltage vs Frequency 13 IOS Short circuit output current Short-circuit vs Supplyy voltage g vs Free-air temperature 14 15 VID Differential input voltage vs Output voltage 16,17 Differential gain vs Load resistance 18 Large-signal differential voltage amplification Differential voltage amplification vs Frequency q y vs Free-air temperature 19,20 , 21,22 zo Output impedance vs Frequency 23,24 CMRR Common mode rejection ratio Common-mode vs Frequency q y vs Free-air temperature 25 26 kSVR Supply voltage rejection ratio Supply-voltage vs Frequency q y vs Free-air temperature 27,28 , 29 IDD Supply current vs Supply voltage 30 SR Slew rate vs Load capacitance vs Free-air temperature 31 32 VO VO Inverting large-signal pulse response 33,34 Voltage-follower large-signal pulse response 35,36 VO VO Inverting small-signal pulse response 37,38 Vn Equivalent input noise voltage vs Frequency Noise voltage (referred to input) Over a 10-second period Total harmonic distortion plus noise vs Frequency Gain bandwidth product Gain-bandwidth vs Supply y voltage g vs Free-air temperature Phase margin vs Frequency q y vs Load capacitance 19,20 , 48 Gain margin vs Load capacitance 49 Unity-gain bandwidth vs Load capacitance 50 AVD THD + N m B1 Voltage-follower small-signal pulse response POST OFFICE BOX 655303 8 39,40 * DALLAS, TEXAS 75265 41, 42 43 44,45 46 47 15 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLV2422 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLV2422 INPUT OFFSET VOLTAGE 18 20 Percentage of Amplifiers - % 16 14 Percentage of Amplifiers - % 452 Amplifiers from 1 Wafer Lot VDD = 3 V RL = 10 k TA = 25C 12 10 8 6 4 454 Amplifiers from 1 Wafer Lot VDD = 5 V RL = 10 k TA = 25C 15 10 5 2 0 0 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 -0.4 -0.3 -0.2 -0.1 0 VIO - Input Offset Voltage - mV Figure 2 Figure 3 INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE 2 2 VDD = 3 V VDD = 5 V 1.5 VIO - Input Offset Voltage - mV VIO - Input Offset Voltage - mV 1.5 1 0.5 0 -0.5 -1 -1.5 -2 -0.5 1 0.5 0 -0.5 -1 -1.5 0 0.5 1 1.5 2 2.5 3 VIC - Common-Mode Input Voltage - V -2 -0.5 0 0.5 1 1.5 2 2.5 Figure 5 POST OFFICE BOX 655303 3 3.5 4 4.5 VIC - Common-Mode Input Voltage - V Figure 4 16 0.1 0.2 0.3 0.4 0.5 0.6 VIO - Input Offset Voltage - mV * DALLAS, TEXAS 75265 5 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLV2422 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT DISTRIBUTION OF TLV2422 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 25 32 Amplifiers From 1 Wafer Lot VDD = 1.5 V TA = 25C to 125C 20 15 10 5 0 -4 32 Amplifiers From 1 Wafer Lot VDD = 2.5 V TA = 25C to 125C 20 Percentage of Amplifiers - % Percentage of Amplifiers - % 25 2 3 -3 -2 -1 0 1 VIO - Temperature Coefficient - V / C 15 10 5 0 4 -4 2 3 -3 -2 -1 0 1 VIO - Temperature Coefficient - V / C Figure 7 HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT INPUT BIAS AND INPUT OFFSET CURRENTS vs FREE-AIR TEMPERATURE 3 200 VDD = 2.5 V VDD = 3 V VOH - High-Level Output Voltage - V I IB and I IO - Input Bias and Input Offset Currents - pA Figure 6 4 160 120 IIB 80 40 2.5 TA = 85C 2 TA = 0C 1.5 TA = 125C 1 TA = 25C 0.5 IIO 0 -55 0 -40 0 25 70 85 125 TA - Free-Air Temperature - C 0 3 6 9 12 15 IOH - High-Level Output Current - mA Figure 8 Figure 9 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 1.6 5 VDD = 3 V VDD = 5 V VOH - High-Level Output Voltage - V VOL - Low-Level Output Voltage - V 1.4 1.2 TA = 125C 1 TA = 85C 0.8 0.6 0.4 TA = 25C 0.2 TA = -40C 4 TA = 25C 3 2 TA = 85C 1 TA = 125C TA = -40C 0 0 1 2 3 4 0 5 0 IOL - Low-Level Output Current - mA 4 12 8 Figure 10 1 TA = 125C 0.8 TA = 85C 0.4 TA = 25C TA = -40C 0 1 2 3 4 5 VO(PP) - Maximum Peak-to-Peak Output Voltage - V VOH - High-Level Output Voltage - V VDD = 5 V 0 28 32 36 40 5 RL = 10 k TA = 25C VDD = 5 V 4 3 VDD = 3 V 2 1 0 102 IOL - Low-Level Output Current - mA 103 104 f - Frequency - Hz Figure 12 18 24 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY 1.2 0.2 20 Figure 11 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 0.6 16 IOH - High-Level Output Current - mA Figure 13 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 105 106 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS SHORT-CIRCUIT OUTPUT CURRENT vs SUPPLY VOLTAGE SHORT-CIRCUIT OUTPUT CURRENT vs FREE-AIR TEMPERATURE 8 30 VO = VDD/2 VIC = VDD/2 TA = 25C 20 VID = -100 mV I OS - Short-Circuit Output Current - mA I OS - Short-Circuit Output Current - mA 25 15 10 5 0 -5 -10 -15 -20 -25 3 4 5 6 8 7 9 4 2 VDD = 5 V 0 -2 -4 -6 VID = 100 mV -8 -55 -30 2 6 10 -40 Figure 14 85 125 DIFFERENTIAL INPUT VOLTAGE vs OUTPUT VOLTAGE 1000 1000 VDD = 3 V RL = 10 k TA = 25C VDD = 5 V RL = 10 k TA = 25C 800 VID - Differential Input Voltage - V VID - Differential Input Voltage - V 70 Figure 15 DIFFERENTIAL INPUT VOLTAGE vs OUTPUT VOLTAGE 800 25 0 TA - Free-Air Temperature - C VDD - Supply Voltage - V 600 400 200 0 -200 -400 -600 -800 600 400 200 0 -200 -400 -600 -800 -1000 0 0.5 1 1.5 2 2.5 3 -1000 0 VO - Output Voltage - V 1 2 3 4 5 VO - Output Voltage - V Figure 16 Figure 17 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS DIFFERENTIAL GAIN vs LOAD RESISTANCE 10000 Differential Gain - V/mV 1000 VID = 5 V VID = 3 V 100 10 1 10 100 1000 RL - Load Resistance - k Figure 18 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY 50 AVD - Large-Signal Differential Voltage Amplification - dB 30 135 20 PHASE 90 10 45 0 GAIN -10 0 -20 -30 - 45 -40 -50 103 104 105 f - Frequency - Hz Figure 19 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 - 90 106 m - Phase Margin - 40 180 VDD = 3 V RL = 10 k CL = 100 pF TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY 60 180 VDD = 5 V RL = 10 k CL = 100 pF AVD - Large-Signal Differential Voltage Amplification - dB 40 135 PHASE 30 90 20 45 10 0 GAIN -10 0 -20 m - Phase Margin - 50 - 45 -30 -40 103 104 - 90 106 105 f - Frequency - Hz Figure 20 DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE 10000 VDD = 3 V AVD - Differential Voltage Amplication - V/mV AVD - Differential Voltage Amplication - V/mV 10000 RL = 1 M 1000 100 RL = 10 k 10 1 -75 -50 -25 0 25 50 75 100 125 VDD = 5 V RL = 1 M 1000 100 RL = 10 k 10 1 -75 -50 TA - Free-Air Temperature - C -25 0 25 50 75 100 125 TA - Free-Air Temperature - C Figure 21 Figure 22 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 21 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS OUTPUT IMPEDANCE vs FREQUENCY OUTPUT IMPEDANCE vs FREQUENCY 1000 1000 AV = 100 AV = 10 z o - Output Impedance - z o - Output Impedance - AV = 100 100 AV = 1 10 AV = 10 100 AV = 1 10 VDD = 3 V TA = 25C VDD = 5 V TA = 25C 1 102 104 103 1 102 105 f - Frequency - Hz Figure 24 COMMON-MODE REJECTION RATIO vs FREQUENCY COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE 94 TA = 25C CMRR - Common-Mode Rejection Ratio - dB CMRR - Common-Mode Rejection Ratio - dB 100 80 60 VDD = 5 V 40 VDD = 3 V 20 103 104 105 106 93 92 VDD = 5 V 91 90 VDD = 3 V 89 88 87 86 85 84 -55 -40 f - Frequency - Hz 0 25 70 85 TA - Free-Air Temperature - C Figure 25 22 105 f - Frequency - Hz Figure 23 0 102 104 103 Figure 26 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 125 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY 120 VDD = 3 V TA = 25C KSVR - Supply-Voltage Rejection Ratio - dB KSVR - Supply-Voltage Rejection Ratio - dB 120 100 KSVR+ 80 60 KSVR- 40 20 0 101 103 102 104 105 VDD = 5 V TA = 25C 100 KSVR+ 80 60 KSVR- 40 20 0 101 106 103 102 f - Frequency - Hz Figure 27 105 106 Figure 28 SUPPLY-VOLTAGE REJECTION RATIO vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs SUPPLY VOLTAGE 100 160 VDD = 2.7 V to 8 V VO = VDD/2 No Load 140 TA = -40C 98 I DD - Supply Current - A k SVR - Supply-Voltage Rejection Ratio - dB 104 f - Frequency - Hz 96 94 TA = 25C 120 100 TA = 85C 80 60 40 92 20 90 -55 -40 0 25 70 85 125 0 0 1 2 TA - Free-Air Temperature - C 3 4 5 6 7 8 9 10 VDD - Supply Voltage - V Figure 29 Figure 30 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS SLEW RATE vs LOAD CAPACITANCE SLEW RATE vs FREE-AIR TEMPERATURE 0.03 0.025 30 VDD = 3 V AV = -1 TA = 25C SR - Slew Rate - V/ms SR - Slew Rate - V/s 25 SR- 0.02 SR+ 0.015 0.01 20 15 10 0.005 0 102 VDD = 5 V RL = 10 k CL = 100 pF AV = 1 104 103 105 5 -55 106 -40 CL - Load Capacitance - pF 0 Figure 31 1500 3 1000 2 VO - Output Voltage - mV VO - Output Voltage - mV 4 500 0 -500 -2000 -1000 VDD = 3 V RL = 10 k CL = 100 pF AV = -1 TA = 25C -600 0 0 -1 -2 200 600 1000 -4 -1000 VDD = 5 V RL = 10 k CL = 100 pF AV = -1 TA = 25C -600 t - Time - s -200 0 200 t - Time - s Figure 34 Figure 33 24 125 1 -3 -200 85 INVERTING LARGE-SIGNAL PULSE RESPONSE 2000 -1500 70 Figure 32 INVERTING LARGE-SIGNAL PULSE RESPONSE -1000 25 TA - Free-Air Temperature - C POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 600 1000 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE 2000 1000 1500 VO - Output Voltage - mV VO - Output Voltage - mV 1500 2000 VDD = 3 V RL = 10 k CL = 100 pF AV = 1 TA = 25C 500 0 -500 -1000 -1500 1000 500 0 -500 -1000 -1500 -2000 -1000 -600 -200 0 200 600 VDD = 5 V RL = 10 k CL = 100 pF AV = 1 TA = 25C -2000 -1000 1000 -600 -200 t - Time - s INVERTING SMALL-SIGNAL PULSE RESPONSE 300 VO - Output Voltage - mV VO - Output Voltage - mV 1000 400 VDD = 3 V RL = 10 k CL = 100 pF AV = -1 TA = 25C 100 0 -100 -200 -300 -400 -5 600 INVERTING SMALL-SIGNAL PULSE RESPONSE 400 200 200 Figure 36 Figure 35 300 0 t - Time - s 200 VDD = 5 V RL = 10 k CL = 100 pF AV = -1 TA = 25C 100 0 -100 -200 -300 -4 -3 -2 -1 0 1 2 3 4 5 -400 -5 -4 t - Time - s -3 -2 -1 0 1 2 3 4 5 t - Time - s Figure 38 Figure 37 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 25 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE 400 200 300 VO - Output Voltage - mV VO - Output Voltage - mV 300 400 VDD = 3 V RL = 10 k CL = 100 pF AV = 1 TA = 25C 100 0 -100 -200 -300 -400 -5 200 VDD = 5 V RL = 10 k CL = 100 pF AV = 1 TA = 25C 100 0 -100 -200 -300 -4 -3 -2 -1 0 1 2 3 4 -400 -5 5 -4 -3 -2 t - Time - s 1 2 3 4 5 Figure 40 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY 120 120 VDD = 3 V TA = 25C Vn - Equivalent Input Noise Voltage - nV/ Hz Vn - Equivalent Input Noise Voltage - nV/ Hz 0 t - Time - s Figure 39 100 80 60 40 20 0 10 102 103 104 VDD = 5 V TA = 25C 100 80 60 40 20 0 10 f - Frequency - Hz 102 103 f - Frequency - Hz Figure 41 26 -1 Figure 42 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 104 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS NOISE VOLTAGE OVER A 10-SECOND PERIOD 1000 Over a 10 Second Period 800 600 VDD = 5 V f = 0.1 Hz to 10 Hz TA = 25C Noise Voltage - nV 400 200 0 -200 -400 -600 -800 -1000 -1200 0 1 2 3 4 6 5 8 7 10 9 t - Time - s Figure 43 100 VDD = 3 V RL = 10 k TA = 25C 10 1 AV = 10 AV = 1 0.1 0.01 101 102 103 TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY THD +N - Total Harmonic Distortion Plus Noise - % THD +N - Total Harmonic Distortion Plus Noise - % TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 104 105 100 VDD = 5 V RL = 10 k TA = 25C 10 1 AV = 10 AV = 1 0.1 0.01 0.001 101 102 103 f - Frequency - Hz f - Frequency - Hz Figure 44 Figure 45 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 104 105 27 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS GAIN-BANDWIDTH PRODUCT vs SUPPLY VOLTAGE GAIN-BANDWIDTH PRODUCT vs FREE-AIR TEMPERATURE 80 80 RL = 10 k CL = 100 pF f = 10 kHz TA = 25C Gain-Bandwidth Product - kHz Gain-Bandwidth Product - kHz 70 VDD = 5 V RL = 10 k CL = 100 pF f = 10 kHz 70 60 50 40 30 60 50 40 30 20 10 20 3 5 4 6 7 0 -50 8 0 -25 25 50 Figure 46 GAIN MARGIN vs LOAD CAPACITANCE 120 40 RL = 10 k TA = 25C Rnull = 500 100 RL = 10 k TA = 25C Rnull = 500 Rnull = 1000 30 80 Gain Margin - dB m - Phase Margin - 125 Figure 47 PHASE MARGIN vs LOAD CAPACITANCE 60 40 Rnull = 1000 Rnull = 200 20 Rnull = 100 Rnull = 200 10 Rnull = 100 20 Rnull = 0 Rnull = 0 0 10 102 103 104 105 0 10 CL - Load Capacitance - pF 102 103 Figure 49 POST OFFICE BOX 655303 104 CL - Load Capacitance - pF Figure 48 28 100 75 TA - Free-Air Temperature - C VDD - Supply Voltage - V * DALLAS, TEXAS 75265 105 TLV2422, TLV2422A Advanced LinCMOS RAIL-TO-RAIL OUTPUT WIDE-INPUT-VOLTAGE MICROPOWER DUAL OPERATIONAL AMPLIFIERS SLOS199C - SEPTEMBER1997 - REVISED APRIL 2001 TYPICAL CHARACTERISTICS UNITY-GAIN BANDWIDTH vs LOAD CAPACITANCE B1 - Unity-Gain Bandwidth - kHz 60 50 40 30 20 10 0 10 102 103 104 105 CL - Load Capacitance - pF Figure 50 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 29 PACKAGE OPTION ADDENDUM www.ti.com 24-Aug-2018 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) 5962-9751401QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9751401QHA TLV2422M TLV2422AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 2422AI TLV2422AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 2422AI TLV2422AIPWR ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 2422AI TLV2422CD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 2422C TLV2422CPWR ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 TV2422 TLV2422ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 2422I TLV2422IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 2422I TLV2422MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9751401QHA TLV2422M (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com (4) 24-Aug-2018 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TLV2422, TLV2422M : * Catalog: TLV2422 * Automotive: TLV2422-Q1, TLV2422-Q1 * Military: TLV2422M NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Military - QML certified for Military and Defense Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TLV2422AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TLV2422AIPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 TLV2422CPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 TLV2422IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLV2422AIDR SOIC D 8 2500 340.5 338.1 20.6 TLV2422AIPWR TSSOP PW 8 2000 367.0 367.0 35.0 TLV2422CPWR TSSOP PW 8 2000 367.0 367.0 35.0 TLV2422IDR SOIC D 8 2500 340.5 338.1 20.6 Pack Materials-Page 2 PACKAGE OUTLINE PW0008A TSSOP - 1.2 mm max height SCALE 2.800 SMALL OUTLINE PACKAGE C 6.6 TYP 6.2 SEATING PLANE PIN 1 ID AREA A 0.1 C 6X 0.65 8 1 3.1 2.9 NOTE 3 2X 1.95 4 5 B 4.5 4.3 NOTE 4 SEE DETAIL A 8X 0.30 0.19 0.1 C A 1.2 MAX B (0.15) TYP 0.25 GAGE PLANE 0 -8 0.15 0.05 0.75 0.50 DETAIL A TYPICAL 4221848/A 02/2015 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side. 5. Reference JEDEC registration MO-153, variation AA. www.ti.com EXAMPLE BOARD LAYOUT PW0008A TSSOP - 1.2 mm max height SMALL OUTLINE PACKAGE 8X (1.5) 8X (0.45) SYMM 1 8 (R0.05) TYP SYMM 6X (0.65) 5 4 (5.8) LAND PATTERN EXAMPLE SCALE:10X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK 0.05 MAX ALL AROUND 0.05 MIN ALL AROUND SOLDER MASK DEFINED NON SOLDER MASK DEFINED SOLDER MASK DETAILS NOT TO SCALE 4221848/A 02/2015 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN PW0008A TSSOP - 1.2 mm max height SMALL OUTLINE PACKAGE 8X (1.5) 8X (0.45) SYMM (R0.05) TYP 1 8 SYMM 6X (0.65) 5 4 (5.8) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:10X 4221848/A 02/2015 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: TLV2422AID TLV2422AIDR TLV2422AIPWR TLV2422AQD TLV2422AQDR TLV2422AQDG4 TLV2422AQDRG4