SOLID TANTALUM ELECTROLYTIC CAPACITORS F97 Resin-molded Chip, High Reliability (High temperature / moisture resistance) Series Specifications Item Type numbering system (Example : 16V 3.3 F) 1 2 3 4 5 6 7 8 9 10 F 9 7 1 C 3 3 5 M B --55 ~ +125C (Rated temperature : 85C.) Capacitance Tolerance 20%, 10% (at 120Hz) Dissipation Factor Refer to P.233 E.S.R. (100kHz) Refer to P.233 Leakage Current * After 1 minute' s application of rated voltage,leakage current at 20C is not more than 0.01CV or 0.5A, whichever is greater. * After 1 minute' s application of rated voltage,leakage current at 85C is not more than 0.1CV or 5A,whichever is greater. * After 1 minute' s application of derated voltage,leakage current at 125C is not more than 0.125CV or 6.3A,whichever is greater. Capacitance Change by Temperature +15% Max. (at +125C) +10% Max. (at +85C) --10% Max. (at --55C) Damp Heat At 85C, 85% R.H.,For 1000 hours (No voltage applied) Capacitance Change * * * * * * Within 10% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * 125% or less of initial specified value Load Humidity After 500 hour' s application of rated voltage in series with a 33 resistor at 60C,90~95% R.H.,capacitors meet the characteristics requirements listed below. Capacitance Change * * * * * * Within 10% of initial value Dissipation Factor * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * 125% or less of initial specified value Temperature Cycles At --55C / +125C,For 30 minutes each,1000 cycles Capacitance Change * * * * * * Within 5% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * * Initial specified value or less Resistance to Soldering Heat At 260C,reflowing capacitors for 10 seconds Max. Capacitance Change * * * * * * Within 5% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * * Initial specified value or less Solderability After immersing capacitors completely into a solder pot at 245C for 2~3 seconds,more than 3/4 of their electrode area shall remain covered with new solder. 11 Taping code (Refer to page 226 for details) Case code Capacitance tolerance Rated Capacitance Rated voltage Series Drawing A * B Case C * N Case L W1 L W1 H H W2 S W2 S S S Surge Dimensions Case code (mm) L 3.2 3.5 6.0 7.3 A B C N W1 1.6 2.8 3.2 4.3 0.2 0.2 0.2 0.2 W2 1.2 2.2 2.2 2.4 0.2 0.2 0.2 0.2 H 1.6 1.9 2.5 2.8 0.1 0.1 0.1 0.1 S 0.8 0.2 0.8 0.2 1.3 0.2 1.3 0.2 0.2 0.2 0.2 0.2 Marking Endurance Month code B Case C Case 10 16r 3.3 16r C105 N Case Shear Test 47 10r A Case Month code Rated Voltage (V) Rated Capacitance (Capacitance code ) Rated voltage (V) Rated Capacitance (F) Rated voltage (Voltage code) Standard ratings V Code 4 0G 6.3 0J 10 1A 16 1C 20 1D 25 1E 35 1V 0.1 104 A1 0.15 154 A1 0.22 224 A1 0.33 334 A 0.47 474 0.68 684 1 105 1.5 155 2.2 225 3.3 335 4.7 6.8 A A * B1 A A A * B1 A A A A A A B B * C1 A A B B B * C1 A A A B B B 475 A A B B B C 685 A B B B C C 10 106 B B B C C 15 156 B B C C N 22 226 B C 33 336 C C 47 476 68 686 100 107 N 150 157 N C C * C N * C C N * C N * N * After Applying the pressure load of 5N for 10 1 seconds horizontally to the center of capacitor side body which has no electrode and has been 5N (0.51kg * f) soldered beforehand on an aluminum For 10 1 seconds substrate,there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with a 20 specified jig at the center of the R230 substrate so that the substrate may bend by 1mm as illustrated. Then,there shall be found no 45 45 remarkable abnormality on the capacitor terminals. As for the surge and derated voltage at 125C, refer to page 225 for details. B A C Terminal Strength After application of surge in series with a 33 resistor at the rate of 30 seconds ON, 30 seconds OFF,for 1000 successive test cycles at 85C,capacitors meet the characteristics requirements listed below. Capacitance Change * * * * * * Within 5% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * * Initial specified value or less After 2000 hours' application of rated voltage in series with a 3 resistor at 85C,or derated voltage in series with a 3 resistor at 125C,capacitors meet the characteristic requirements listed below. Capacitance Change * * * * * * Within 10% of initial value Dissipation Factor * * * * * * * * * * * Initial specified value or less Leakage Current * * * * * * * * * * * * * Initial specified value or less 1mm Cap. (F) Performance Characteristics Category Temperature Range C C * N1 N N N 1 is old series. Please choice another series for new design. N N N N N N CAT.8100T SOLID TANTALUM ELECTROLYTIC CAPACITORS F97 Standard ratings Rated Rated Volt Capacitance (F) 4V 6.3V 10V 16V 20V 3.3 4.7 6.8 10 15 22 33 47 68 68 100 150 2.2 3.3 4.7 6.8 10 15 22 33 47 47 68 100 1.5 2.2 3.3 4.7 6.8 10 15 22 33 33 47 1 1.5 2.2 3.3 4.7 6.8 10 15 22 22 33 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 22 Case code Part Number Leakage Current (A) A A A B B B C C C N N N A A A B B B C C C N N N A A A B B B C C C N N A A A B B B C C C N N A A A B B B C C N N F970G335MAA F970G475MAA F970G685MAA F970G106MBA F970G156MBA F970G226MBA F970G336MCC F970G476MCC F970G686MCC F970G686MNC F970G107MNC F970G157MNC F970J225MAA F970J335MAA F970J475MAA F970J685MBA F970J106MBA F970J156MBA F970J226MCC F970J336MCC F970J476MCC F970J476MNC F970J686MNC F970J107MNC F971A155MAA F971A225MAA F971A335MAA F971A475MBA F971A685MBA F971A106MBA F971A156MCC F971A226MCC F971A336MCC F971A336MNC F971A476MNC F971C105MAA F971C155MAA F971C225MAA F971C335MBA F971C475MBA F971C685MBA F971C106MCC F971C156MCC F971C226MCC F971C226MNC F971C336MNC F971D684MAA F971D105MAA F971D155MAA F971D225MBA F971D335MBA F971D475MBA F971D685MCC F971D106MCC F971D156MNC F971D226MNC 0.5 0.5 0.5 0.5 0.6 0.9 1.3 1.9 2.7 2.7 4.0 6.0 0.5 0.5 0.5 0.5 0.6 0.9 1.4 2.1 3.0 3.0 4.3 6.3 0.5 0.5 0.5 0.5 0.7 1.0 1.5 2.2 3.3 3.3 4.7 0.5 0.5 0.5 0.5 0.8 1.1 1.6 2.4 3.5 3.5 5.3 0.5 0.5 0.5 0.5 0.7 0.9 1.4 2.0 3.0 4.4 Disspation Factor (%@120Hz) 6 6 6 6 6 6 6 6 6 6 8 8 6 6 6 6 6 6 6 6 6 6 6 8 4 6 6 6 6 6 6 6 6 6 6 4 4 6 6 6 6 6 6 8 6 6 4 4 6 6 6 6 6 6 6 6 E.S.R. (@100kHz) 4.5 4.0 3.5 2.1 2.0 1.9 1.1 0.9 0.8 0.6 0.6 0.6 5.0 4.5 4.0 2.5 2.1 2.0 1.1 1.1 0.9 0.7 0.6 0.6 6.0 5.0 4.5 2.8 2.5 2.0 1.2 1.1 1.1 0.7 0.7 7.5 6.3 5.0 3.1 2.8 2.5 1.5 1.2 1.1 0.7 0.7 7.6 7.5 6.7 3.8 3.1 2.8 1.8 1.5 0.7 0.7 Rated Rated Volt Capacitance (F) 25V 35V 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 10 15 0.1 0.15 0.22 0.33 0.47 0.47 0.68 0.68 1 1.5 1.5 2.2 2.2 3.3 4.7 4.7 6.8 10 Case code Part Number Leakage Current (A) A A A B B B C C C N N A A A A A B A B B B C B C C C N N N F971E474MAA F971E684MAA F971E105MAA F971E155MBA F971E225MBA F971E335MBA F971E475MCC F971E685MCC F971E106MCC F971E106MNC F971E156MNC F971V104MAA*1 F971V154MAA*1 F971V224MAA*1 F971V334MAA F971V474MAA F971V474MBA*1 F971V684MAA F971V684MBA*1 F971V105MBA F971V155MBA F971V155MCC*1 F971V225MBA F971V225MCC*1 F971V335MCC F971V475MCC F971V475MNC*1 F971V685MNC F971V106MNC 0.5 0.5 0.5 0.5 0.6 0.8 1.2 1.7 2.5 2.5 3.8 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.8 0.8 1.2 1.6 1.6 2.4 3.5 Disspation Factor (%@120Hz) 4 4 4 4 6 6 6 6 6 6 6 4 4 4 4 4 4 4 4 4 6 4 6 6 6 6 6 6 6 E.S.R. (@100kHz) 10.0 7.6 7.5 4.0 3.8 3.5 1.8 1.8 1.6 1.0 0.7 15.0 15.0 12.0 12.0 10.0 5.0 7.6 5.0 4.0 4.0 2.0 3.8 2.0 2.0 1.8 1.0 1.0 1.0 1 is old series. Please choice another series for new design. CAT.8100T