SLUS579 - OCTOBER, 2003 FEATURES D Controls Boost Preregulator to Near-Unity D D D D D D D D D D D DESCRIPTION The UCC2819A/UCC3819A provides all the functions necessary for active power factor corrected preregulators. The controller achieves near unity power factor by shaping the ac-input line current waveform to correspond to that of the ac-input line voltage. Average current mode control maintains stable, low distortion sinusoidal line current. Power Factor World Wide Line Operation Over-Voltage Protection Accurate Power Limiting Average Current Mode Control Improved Noise Immunity Improved Feed-Forward Line Regulation Leading Edge Modulation 150-A Typical Start-Up Current Low-Power BiCMOS Operation 10.8-V to 17-V Operation Programmable Output Voltage (Tracking Boost Topology) Designed in Texas Instrument's BiCMOS process, the UCC3819A offers new features such as lower start-up current, lower power dissipation, overvoltage protection, a shunt UVLO detect circuitry and a leading-edge modulation technique to reduce ripple current in the bulk capacitor. The UCC3819A allows the output voltage to be programmed by bringing out the error amplifier noninverting input. BLOCK DIAGRAM VCC 15 OVP/EN 10 7.5 V REFERENCE 1.9 V VAOUT 7 VSENSE 11 - VFF ENABLE 0.33 V VOLTAGE ERROR AMP 8 X 16 DRVOUT 1 GND 2 PKLMT 10.2 V/9.7 V ZERO POWER VCC - + X / MULT X 13 VREF UVLO + + VAI - 9 CURRENT AMP 8.0 V OVP - - - + 2 + PWM S + PWM LATCH R R OSC CLK MIRROR 2:1 Q CLK IAC MOUT 6 OSCILLATOR - + 5 4 3 12 14 CAI CAOUT RT CT UDG-03124 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. ! "#$ ! %#&'" ($) (#"! " !%$""! %$ *$ $! $+! !#$! !(( ,-) (#" %"$!!. ($! $"$!!'- "'#($ $!. '' %$$!) Copyright 2003, Texas Instruments Incorporated www.ti.com 1 SLUS579 - OCTOBER, 2003 DESCRIPTION (CONTINUED) The UCC3819A is directly pin for pin compatible with the UCC3819. Only the output stage of UCC3819A has been modified to allow use of a smaller external gate drive resistor values. For some power supply designs where an adequately high enough gate drive resistor can not be used, the UCC3819A offers a more robust output stage at the cost of increasing the internal gate resistances. The gate drive of the UCC3819A remains strong at 1.2 A of peak current capability. Available in the 16-pin D, N, and PW packages. PIN CONNECTION DIAGRAM D, N, AND PW PACKAGES (TOP VIEW) GND PKLMT CAOUT CAI MOUT IAC VAOUT VFF 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DRVOUT VCC CT VAI RT VSENSE OVP/EN VREF AVAILABLE OPTIONS TABLE PACKAGE DEVICES TA = TJ SOIC (D) PACKAGE(1) PDIP (N) PACKAGE TSSOP (PW) PACKAGE(1) 0C to 70C UCC3819AD UCC3819AN UCC3819APW -40C to 85C UCC2819AD UCC2819AN UCC2819APW NOTES: (1) The D and PW packages are available taped and reeled. Add R suffix to the device type (e.g. UCC3819ADR) to order quantities of 2,500 devices per reel (D package) and 2,000 devices per reel (for PW package). Bulk quantities are 40 units (D package) and 90 units (PW package) per tube. THERMAL RESISTANCE TABLE PACKAGE jc(C/W) SOIC-16 (D) 22 ja(C/W) 40 to 70 (1) PDIP-16 (N) 12 14 (2) 25 to 50 (1) 123 to 147 (2) TSSOP-16 (PW) NOTES: (1) Specified ja (junction to ambient) is for devices mounted to 5-inch2 FR4 PC board with one ounce copper where noted. When resistance range is given, lower values are for 5 inch2 aluminum PC board. Test PWB was 0.062 inch thick and typically used 0.635-mm trace widths for power packages and 1.3-mm trace widths for non-power packages with a 100-mil x 100-mil probe land area at the end of each trace. (2) Modeled data. If value range given for ja, lower value is for 3x3 inch. 1 oz internal copper ground plane, higher value is for 1x1-inch. ground plane. All model data assumes only one trace for each non-fused lead. 2 www.ti.com SLUS579 - OCTOBER, 2003 ABSOLUTE MAXIMUM RATINGS over operating free-air temperature (unless otherwise noted) UCCx81xA UNIT Supply voltage VCC 18 V Gate drive current, continuous 0.2 Gate drive current 1.2 Input voltage, CAI, MOUT, SS A 8 Input voltage, PKLMT 5 Input voltage, VSENSE, OVP/EN, VAI 10 Input current, RT, IAC, PKLMT 10 Maximum negative voltage, DRVOUT, PKLMT, MOUT Power dissipation V -0.5 V 1 W Junction temperature, TJ -55 to 150 Storage temperature, Tstg -65 to 150 Lead temperature, Tsol (soldering, 10 seconds) mA C C 300 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS TA = 0C to 70C for the UCC3819A, -40C to 85C for the UCC2819A, VCC = 12 V, RT = 22 k, CT = 270 pF, (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS 150 300 A 2 4 6 mA VCC turnon threshold 9.7 10.2 10.8 VCC turnoff threshold 9.4 9.7 UVLO hysteresis 0.3 0.5 Supply Current Supply current, off VCC = (VCC turnon threshold -0.3 V) Supply current, on VCC = 12 V, No load on DRVOUT UVLO V Voltage Amplifier VIO VAOUT = 2.75 V, VCM = 3.75 V VAI bias current VAOUT = 2.75 V, VCM = 3.75 V 50 200 VSENSE bias current CMRR VSENSE = VREF, VAOUT = 2.5 V 50 200 VCM = 1 V to 7.5 V 50 70 Open loop gain VAOUT = 2 V to 5 V 50 90 High-level output voltage IL = -150 A IL = 150 A 5.3 5.5 5.6 V 0 50 150 mV Low-level output voltage -15 15 mV nA dB NOTES: 1. Ensured by design, Not production tested. 2. Reference variation for VCC < 10.8 V is shown in Figure 2. www.ti.com 3 SLUS579 - OCTOBER, 2003 ELECTRICAL CHARACTERISTICS TA = 0C to 70C for the UCC3819A, -40C to 85C for the UCC2819A, VCC = 12 V, RT = 22 k, CT = 270 pF, (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS VREF +0.48 VREF +0.50 VREF +0.52 V Hysteresis 300 500 600 Enable threshold 1.7 1.9 2.1 Enable hysteresis 0.1 0.2 0.3 Over Voltage Protection and Enable Over voltage reference mV V Current Amplifier Input offset voltage Input bias current Input offset current Open loop gain Common-mode rejection ratio High-level output voltage Low-level output voltage Gain bandwidth product VCM = 0 V, VCM = 0 V, VCAOUT = 3 V VCAOUT = 3 V VCM = 0 V, VCM = 0 V, VCAOUT = 3 V VCAOUT = 2 V to 5 V 90 VCM = 0 V to 1.5 V, IL = -120 A VCAOUT = 3 V 60 80 5.6 6.5 6.8 0.1 0.2 0.5 IL = 1 mA See Note 1 -3.5 0 2.5 -50 -100 25 100 mV nA dB 2.5 V MHz Voltage Reference Input voltage, (UCC3819A) Input voltage, (UCC2819A) Load regulation TA = 0C to 70C TA = -40C to 85C Line regulation IREF = 1 mA to 2 mA VCC = 10.8 V to 15 V, Short-circuit current VREF = 0 V See Note 2 7.387 7.5 7.613 7.369 7.5 7.631 0 10 0 10 V mV -20 -25 -50 mA 85 100 115 kHz Oscillator Initial accuracy Voltage stability TA = 25C VCC = 10.8 V to 15 V Total variation Line, temp, See Note 1 -1% 1% 80 120 kHz Ramp peak voltage 4.5 5 5.5 Ramp amplitude voltage (peak to peak) 3.5 4 4.5 15 mV 350 500 ns V Peak Current Limit PKLMT reference voltage -15 PKLMT propagation delay 150 NOTES: (1) Ensured by design, Not production tested. (2) Reference variation for VCC < 10.8 V is shown in Figure 2. 4 www.ti.com SLUS579 - OCTOBER, 2003 ELECTRICAL CHARACTERISTICS TA = 0C to 70C for the UCC3819A, -40C to 85C for the UCC2819A, VCC = 12 V, RT = 22 k, CT = 270 pF, (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX -6 -20 UNITS Multiplier IMOUT, high line, low power output current, (0C to 85C) IAC = 500 A, VFF = 4.7 V, VAOUT = 1.25 V 0 IMOUT, high line, low power output current, (-40C to 85C) IAC = 500 A, VFF = 4.7 V, VAOUT = 1.25 V 0 IMOUT, high line, high power output current IAC = 500 A, VFF = 4.7 V, VAOUT = 5 V -70 -90 -105 IMOUT, low line, low power output current IAC = 150 A, VFF = 1.4 V, VAOUT = 1.25 V -10 -19 -50 IMOUT, low line, high power output current IAC = 150 A, VFF = 1.4 V, VAOUT = 5 V -268 -300 -346 IMOUT, IAC limited Gain constant (K) IAC = 150 A, IAC = 300 A, VFF = 1.3 V, VFF = 3 V, VAOUT = 5 V -250 -300 -400 0.5 1 1.5 VFF = 1.4 V, VFF = 4.7 V, VAOUT = 0.25 V 0 -2 IMOUT, zero current IAC = 150 A, IAC = 500 A, VAOUT = 0.25 V 0 -2 IMOUT, zero current, (0C to 85C) IMOUT, zero current, (-40C to 85C) IAC = 500 A, IAC = 500 A, VFF = 4.7 V, VFF = 4.7 V, VAOUT = 0.5 V 0 -3 Power limit (IMOUT x VFF) IAC = 150 A, VFF = 1.4 V, VAOUT = 5 V VAOUT = 2.5 V VAOUT = 0.5 V -23 A 1/V A A 0 -3.5 -375 -420 -485 W -140 -150 -160 A 9 12 4 10 25 50 10 50 95% 100% Feed-Forward VFF output current IAC = 300 A Gate Driver Pullup resistance Pulldown resistance IO = -100 mA to -200 mA IO = 100 mA Output rise time CL = 1 nF, RL = 10 , Output fall time CL = 1 nF, RL = 10 , Maximum duty cycle Minimum controlled duty cycle VDRVOUT = 0.7 V to 9 V VDRVOUT = 9 V to 0.7 V 93% At 100 kHz ns 2% Zero Power Zero power comparator threshold Measured on VAOUT 0.20 0.33 0.50 V NOTES: (1) Ensured by design, Not production tested. (2) Reference variation for VCC < 10.8 V is shown in Figure 2. www.ti.com 5 SLUS579 - OCTOBER, 2003 PIN ASSIGNMENTS TERMINAL NAME I/O NO. DESCRIPTION CAI 4 I Current amplifier noninverting input CAOUT 3 O Current amplifier output CT 14 I Oscillator timing capacitor DRVOUT 16 O Gate drive GND 1 - Ground IAC 6 I Current proportional to input voltage MOUT 5 I/O OVP/EN 10 I Over-voltage/enable PKLMT 2 I PFC peak current limit RT 12 I Oscillator charging current VAI 13 I Voltage amplifier non-inverting input VAOUT 7 O Voltage amplifier output VCC 15 I Positive supply voltage VFF 8 I Feed-forward voltage VSENSE 11 I Voltage amplifier inverting input VREF 9 O Voltage reference output Multiplier output and current amplifier inverting input Pin Descriptions CAI: Place a resistor between this pin and the GND side of current-sense resistor. This input and the inverting input (MOUT) remain functional down to and below GND. CAOUT: This is the output of a wide bandwidth operational amplifier that senses line current and commands the PFC pulse-width modulator (PWM) to force the correct duty cycle. Compensation components are placed between CAOUT and MOUT. CT: A capacitor from CT to GND sets the PWM oscillator frequency according to: f[ RT0.6CT The lead from the oscillator timing capacitor to GND should be as short and direct as possible. DRVOUT: The output drive for the boost switch is a totem-pole MOSFET gate driver on DRVOUT. To avoid the excessive overshoot of the DRVOUT while driving a capacitive load, a series gate current-limiting/damping resistor is recommended to prevent interaction between the gate impedance and the output driver. The value of the series gate resistor is based on the pulldown resistance (Rpulldown which is 4- typical), the maximum VCC voltage (VCC), and the required maximum gate drive current (Imax). Using the equation below, a series gate resistance of resistance 11 would be required for a maximum VCC voltage of 18 V and for 1.2 A of maximum sink current. The source current will be limited to approximately 900 mA (based on the Rpullup of 9- typical). R GATE + VCC * I MAX R pulldown I MAX GND: All voltages measured with respect to ground. VCC and REF should be bypassed directly to GND with a 0.1-F or larger ceramic capacitor. 6 www.ti.com SLUS579 - OCTOBER, 2003 Pin Descriptions (continued) IAC: This input to the analog multiplier is a current proportional to instantaneous line voltage. The multiplier is tailored for very low distortion from this current input (IIAC) to multiplier output. The recommended maximum IIAC is 500 A. MOUT: The output of the analog multiplier and the inverting input of the current amplifier are connected together at MOUT. As the multiplier output is a current, this is a high-impedance input so the amplifier can be configured as a differential amplifier. This configuration improves noise immunity and allows for the leading-edge modulation operation. The multiplier output current is limited to 2 I IAC. The multiplier output current is given by the equation: I MOUT + I IAC (V VAOUT * 1) V VFF 2 K where K + 1 is the multiplier gain constant. V OVP/EN: A window comparator input that disables the output driver if the boost output voltage is a programmed level above the nominal or disables both the PFC output driver and resets SS if pulled below 1.9 V (typ). PKLMT: The threshold for peak limit is 0 V. Use a resistor divider from the negative side of the current sense resistor to VREF to level shift this signal to a voltage level defined by the value of the sense resistor and the peak current limit. Peak current limit is reached when PKLMT voltage falls below 0 V. RT: A resistor from RT to GND is used to program oscillator charging current. A resistor between 10 k and 100 k is recommended. Nominal voltage on this pin is 3 V. VAI: This input can be tied to the VREF or any other voltage reference (7.5 V) to set the boost regulator output voltage. VAOUT: This is the output of the operational amplifier that regulates output voltage. The voltage amplifier output is internally limited to approximately 5.5 V to prevent overshoot. VCC: Connect to a stable source of at least 20 mA between 10 V and 17 V for normal operation. Bypass VCC directly to GND to absorb supply current spikes required to charge external MOSFET gate capacitances. To prevent inadequate gate drive signals, the output devices are inhibited unless VVCC exceeds the upper under-voltage lockout voltage threshold and remains above the lower threshold. VFF: The RMS voltage signal generated at this pin by mirroring 1/2 of the IIAC into a single pole external filter. At low line, the VFF roll should be 14 V. VSENSE: This is normally connected to a compensation network and to the boost converter output through a divider network. VREF: VREF is the output of an accurate 7.5-V voltage reference. This output is capable of delivering 20 mA to peripheral circuitry and is internally short-circuit current limited. VREF is disabled and remains at 0 V when VVCC is below the UVLO threshold. Bypass VREF to GND with a 0.1-F or larger ceramic capacitor for best stability. Please refer to Figures 8 and 9 for VREF line and load regulation characteristics. www.ti.com 7 SLUS579 - OCTOBER, 2003 APPLICATION INFORMATION The UCC3819A is based on the UCC3818 PFC preregulator. For a more detailed application information for this part, please refer to the UCC3818 datasheet product folder. The main difference between the UCC3818 and the UCC3819A is that the non-inverting input of the voltage error amplifier is made available to the user through an external pin (VAI) in the UCC3819A. The SS pin and function were eliminated to accommodate this change. The benefit of VAI pin is that it can be used to dynamically change the PFC output voltage based on the line voltage (RMS) level or other conditions. Figure 1 shows one suggested implementation of the tracking boost PFC converter as this approach is sometimes referred to. The VAI pin is tied to the VFF pin and hence output voltage scales up with the line voltage. The benefit of this approach is that at lower line voltages the output voltage is lower and that leads to smaller boost inductor value, lower MOSFET conduction losses and reduced component stresses. In order for this feature to work, the downstream converter has to operate over a wider input range. R21 R13 IAC VO D1 AC2 F1 + D2 C14 VLINE C13 Q1 D3 VOUT AC1 C12 R14 - R17 UCC3819A R9 R12 R10 1 GND DRVOUT 16 D4 2 PKLIMIT 3 CAOUT 4 CAI 5 MOUT CT 14 6 IAC VAI 13 RT 12 D5 R11 VREF C9 R8 VCC 15 C2 C1 C4 C8 VFF C7 D6 R7 VCC (FROM BIAS SUPPLY) C3 C15 R1 VSENSE 11 7 VAOUT 8 VFF R3 R2 R19 C6 R20 VO R4 OVP/EN 10 R6 C5 VREF R5 9 VREF UDG-01008 Figure 1. Suggested Implementation of UCC3819A in a Tracking Boost PFC Preregulator 8 www.ti.com SLUS579 - OCTOBER, 2003 APPLICATION INFORMATION REFERENCE VOLTAGE vs REFERENCE CURRENT REFERENCE VOLTAGE vs SUPPLY VOLTAGE 7.510 VREF - Reference Voltage - V VREF - Reference Voltage - V 7.60 7.55 7.50 7.505 7.500 7.45 7.495 7.40 7.490 9 10 11 12 13 0 14 5 Figure 2 15 20 25 Figure 3 MULTIPLIER OUTPUT CURRENT vs VOLTAGE ERROR AMPLIFIER OUTPUT MULTIPLIER GAIN vs VOLTAGE ERROR AMPLIFIER OUTPUT 1.5 350 300 1.3 IAC = 150 A IAC = 150 A 250 1.1 200 IAC = 300 A 150 100 50 Multiplier Gain - K IMOUT - Multiplier Output Current - A 10 IVREF - Reference Current - mA VCC - Supply Voltage - V 0.9 IAC = 300 A IAC = 500 A 0.7 IAC = 500 A 0.5 0 0.0 1.0 2.0 3.0 4.0 5.0 VAOUT - Voltage Error Amplifier Output - V 1.0 2.0 3.0 4.0 5.0 VAOUT - Voltage Error Amplifier Output - V Figure 5 Figure 4 www.ti.com 9 SLUS579 - OCTOBER, 2003 APPLICATION INFORMATION MULTIPLIER CONSTANT POWER PERFORMANCE (VFF x IMOUT) - W 500 400 VAOUT = 5 V 300 VAOUT = 4 V 200 VAOUT = 3 V 100 VAOUT = 2 V 0 0.0 1.0 2.0 3.0 4.0 VFF - Feedforward Voltage - V 5.0 Figure 6 References and Resources: Application Note: Differences Between UCC3817A/18A/19A and UCC3817/18/19, Texas Instruments Literature Number SLUA294 User's Guide: UCC3817 BiCMOS Power Factor Preregulator Evaluation Board, Texas Instruments Literature Number SLUU077 Application Note: Synchronizing a PFC Controller from a Down Stream Controller Gate Drive, Texas Instruments Literature Number SLUA245 Seminar topic: High Power Factor Switching Preregulator Design Optimization, L.H. Dixon, SEM-700,1990. Seminar topic: High Power Factor Preregulator for Off-line Supplie", L.H. Dixon, SEM-600, 1988. Related Products DEVICE UCC3817/A,18/A DESCRIPTION BiCMOS PFC controller UC3854 PFC controller UC3854A/B Improved PFC controller UC3855A/B High performance soft switching PFC controller UCC38050/1 Transition mode PFC controller UCC28510/11/12/13 Advanced PFC+PWM combo controller UCC28514/15/16/17 Advanced PFC+PWM combo controller NOTES: (1). Critical conduction mode (2). Average current mode 10 www.ti.com CONTROL METHOD ACM(2) TYPICAL POWER LEVEL ACM(2) ACM(2) 200 W to 2 kW+ ACM(2) CRM(1) 400 W to 2 kW+ ACM(2) ACM(2) 75 W to 1kW+ 75 W to 2 kW+ 200 W to 2 kW+ 50 W to 400 W 75 W to 1kW+ PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) UCC2819AD ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2819ADG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2819ADR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2819ADRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2819APW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2819APWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2819APWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2819APWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC3819AD ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3819ADG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3819ADR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3819ADRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3819APW ACTIVE TSSOP PW 16 TBD Call TI Call TI UCC3819APWG4 ACTIVE TSSOP PW 16 TBD Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 10.3 2.1 8.0 16.0 Q1 UCC2819ADR SOIC D 16 2500 330.0 16.4 6.5 UCC2819APWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 UCC3819ADR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UCC2819ADR SOIC D 16 2500 333.2 345.9 28.6 UCC2819APWR TSSOP PW 16 2000 367.0 367.0 35.0 UCC3819ADR SOIC D 16 2500 333.2 345.9 28.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated