DS90C363, DS90CF364 www.ti.com SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 +3.3V Programmable LVDS Transmitter 18-Bit Flat Panel Display (FPD) Link-65 MHz, +3.3V LVDS Receiver 18-Bit Flat Panel Display (FPD) Link-65 MHz Check for Samples: DS90C363, DS90CF364 FEATURES DESCRIPTION * * The DS90C363 transmitter converts 21 bits of CMOS/TTL data into three LVDS (Low Voltage Differential Signaling) data streams. A phase-locked transmit clock is transmitted in parallel with the data streams over a fourth LVDS link. Every cycle of the transmit clock 21 bits of input data are sampled and transmitted. The DS90CF364 receiver converts the LVDS data streams back into 21 bits of CMOS/TTL data. At a transmit clock frequency of 65 MHz, 18 bits of RGB data and 3 bits of LCD timing and control data (FPLINE, FPFRAME, DRDY) are transmitted at a rate of 455 Mbps per LVDS data channel. Using a 65 MHz clock, the data throughput is 170 Mbyte/sec. The Transmitter is offered with programmable edge data strobes for convenient interface with a variety of graphics controllers. The Transmitter can be programmed for Rising edge strobe or Falling edge strobe through a dedicated pin. A Rising edge Transmitter will inter-operate with a Falling edge Receiver (DS90CF364) without any translation logic. 1 23 * * * * * * * * * * * * * * * 20 to 65 MHz shift clock support Programmable Transmitter (DS90C363) strobe select (Rising or Falling edge strobe) Single 3.3V supply Chipset (TX + RX) power consumption < 250 mW (typ) Power-down mode (< 0.5 mW total) Single pixel per clock XGA (1024x768) ready Supports VGA, SVGA, XGA and higher addressability Up to 170 Megabyte/sec bandwidth Up to 1.3 Gbps throughput Narrow bus reduces cable size and cost 290 mV swing LVDS devices for low EMI PLL requires no external components Low profile 48-lead TSSOP package Falling edge data strobe Receiver Compatible with TIA/EIA-644 LVDS standard ESD rating > 7 kV Operating Temperature: -40C to +85C This chipset is an ideal means to solve EMI and cable size problems associated with wide, high speed TTL interfaces. Block Diagrams Figure 1. Application 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. TRI-STATE is a registered trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2013, Texas Instruments Incorporated DS90C363, DS90CF364 SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 www.ti.com Figure 2. DS90C363 Figure 3. DS90CF364 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) -0.3V to +4V Supply Voltage (VCC) CMOS/TTL Input Voltage -0.3V to (VCC + 0.3V) CMOS/TTL Output Voltage -0.3V to (VCC + 0.3V) LVDS Receiver Input Voltage -0.3V to (VCC + 0.3V) LVDS Driver Output Voltage -0.3V to (VCC + 0.3V) LVDS Output Short Circuit Duration Continuous Junction Temperature +150C Storage Temperature -65C to +150C Lead Temperature (Soldering, 4 seconds) +260C Maximum Package Power Dissipation Capacity at 25C (TSSOP Package) Package Derating ESD Rating (1) DS90C363 1.98 W DS90CF364 1.89 W DS90C363 16 mW/C above +25C DS90CF364 15 mW/C above +25C HBM, 1.5 k, 100 pF > 7 kV "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The tables of "Electrical Characteristics" specify conditions for device operation. Recommended Operating Conditions Supply Voltage (VCC) Operating Free Air Temperature (TA) Receiver Input Range Min Nom Max Unit 3.0 3.3 3.6 V -40 +25 +85 C 0 Supply Noise Voltage (VCC) 2 Submit Documentation Feedback 2.4 V 100 mVPP Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 DS90C363, DS90CF364 www.ti.com SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit CMOS/TTL DC SPECIFICATIONS VIH High Level Input Voltage 2.0 VCC V VIL Low Level Input Voltage GND 0.8 V VOH High Level Output Voltage IOH = -0.4 mA VOL Low Level Output Voltage IOL = 2 mA 0.06 0.3 VCL Input Clamp Voltage ICL = -18 mA -0.79 -1.5 V IIN Input Current VIN = VCC, GND, 2.5V or 0.4V 5.1 10 A IOS Output Short Circuit Current VOUT = 0V -60 -120 mA 345 450 mV 35 mV 2.7 3.3 V V LVDS DC SPECIFICATIONS VOD Differential Output Voltage RL = 100 250 VOD Change in VOD between complimentary output states VOS Offset Voltage VOS Change in V OS between complimentary output states IOS Output Short Circuit Current VOUT = 0V, RL = 100 IOZ Output TRI-STATE(R) Current PWR DWN = 0V, VOUT = 0V or VCC VTH Differential Input High Threshold VCM = +1.2V VTL Differential Input Low Threshold IIN Input Current (1) 1.125 1.25 1.375 V 35 mV -3.5 -5 mA 1 10 A +100 mV -100 mV VIN = +2.4V, VCC = 3.6V 10 A VIN = 0V, VCC = 3.6V 10 A TRANSMITTER SUPPLY CURRENT ICCTW ICCTG ICCTZ Transmitter Supply Current, Worst RL = 100, Case CL = 5 pF, Worst Case Pattern (Figure 4 Figure 6 ), TA = -40C to +85C f = 32.5 MHz 31 45 mA f = 37.5 MHz 32 50 mA f = 65 MHz 42 55 mA Transmitter Supply Current, 16 Grayscale f = 32.5 MHz 23 35 mA f = 37.5 MHz 28 40 mA f = 65 MHz 31 45 mA 10 55 A RL = 100, CL = 5 pF, 16 Grayscale Pattern (Figure 5 Figure 6 ), TA = -40C to +85C Transmitter Supply Current, Power PWR DWN = Low, Down Driver Outputs in TRI-STATE(R) under Power Down Mode RECEIVER SUPPLY CURRENT ICCRW ICCRG ICCRZ (1) Receiver Supply Current, Worst Case Receiver Supply Current, 16 Grayscale Receiver Supply Current, Power Down CL = 8 pF, Worst Case Pattern (Figure 4 Figure 7 ), TA = -40C to +85C f = 32.5 MHz 49 65 mA f = 37.5 MHz 53 70 mA f = 65 MHz 78 105 mA CL = 8 pF, 16 Grayscale Pattern (Figure 5 Figure 7 ), TA = -40C to +85C f = 32.5 MHz 28 45 mA f = 37.5 MHz 30 47 mA f = 65 MHz 43 60 mA 10 55 A PWR DWN = Low, Receiver Outputs Stay Low during Power Down Mode VOS previously referred as VCM. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 Submit Documentation Feedback 3 DS90C363, DS90CF364 SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 www.ti.com Transmitter Switching Characteristics Over recommended operating supply and -40C to +85C ranges unless otherwise specified Symbol Parameter Min Typ Max Unit LLHT LVDS Low-to-High Transition Time (Figure 6 ) 0.75 1.5 ns LHLT LVDS High-to-Low Transition Time (Figure 6 ) 0.75 1.5 ns TCIT TxCLK IN Transition Time (Figure 8 ) 5 ns TCCS TxOUT Channel-to-Channel Skew (Figure 9 ) TPPos0 Transmitter Output Pulse Position for Bit 0 (Figure 20 ) -0.4 0 0.3 ns TPPos1 Transmitter Output Pulse Position for Bit 1 1.8 2.2 2.5 ns TPPos2 Transmitter Output Pulse Position for Bit 2 4.0 4.4 4.7 ns TPPos3 Transmitter Output Pulse Position for Bit 3 6.2 6.6 6.9 ns TPPos4 Transmitter Output Pulse Position for Bit 4 8.4 8.8 9.1 ns TPPos5 Transmitter Output Pulse Position for Bit 5 10.6 11.0 11.3 ns TPPos6 Transmitter Output Pulse Position for Bit 6 12.8 13.2 13.5 ns TCIP TxCLK IN Period (Figure 10) 15 T 50 ns TCIH TxCLK IN High Time (Figure 10) 0.35T 0.5T 0.65T ns TCIL TxCLK IN Low Time (Figure 10) 0.35T 0.5T 0.65T ns TSTC TxIN Setup to TxCLK IN (Figure 10 ) THTC TxIN Hold to TxCLK IN (Figure 10 ) TCCD TxCLK IN to TxCLK OUT Delay at 25C, VCC = 3.3V (Figure 12 ) TPLLS TPDD 250 f = 65 MHz f = 65 MHz ps 2.5 ns 0 3.0 ns 3.7 5.5 ns Transmitter Phase Lock Loop Set (Figure 14 ) 10 ms Transmitter Power Down Delay (Figure 18 ) 100 ns Receiver Switching Characteristics Over recommended operating supply and -40C to +85C ranges unless otherwise specified Typ Max Unit CLHT Symbol CMOS/TTL Low-to-High Transition Time (Figure 7 ) Parameter 2.2 5.0 ns CHLT CMOS/TTL High-to-Low Transition Time (Figure 7 ) 2.2 5.0 ns RSPos0 Receiver Input Strobe Position for Bit 0 (Figure 21 ) 0.7 1.1 1.4 ns RSPos1 Receiver Input Strobe Position for Bit 1 2.9 3.3 3.6 ns RSPos2 Receiver Input Strobe Position for Bit 2 5.1 5.5 5.8 ns RSPos3 Receiver Input Strobe Position for Bit 3 7.3 7.7 8.0 ns RSPos4 Receiver Input Strobe Position for Bit 4 9.5 9.9 10.2 ns RSPos5 Receiver Input Strobe Position for Bit 5 11.7 12.1 12.4 ns RSPos6 Receiver Input Strobe Position for Bit 6 13.9 14.3 14.6 ns 15 T 50 (1) f = 65 MHz RSKM RxIN Skew Margin RCOP RxCLK OUT Period (Figure 11) RCOH RxCLK OUT High Time (Figure 11 ) f = 65 MHz 7.3 8.6 ns RCOL RxCLK OUT Low Time (Figure 11) f = 65 MHz 3.45 4.9 ns RSRC RxOUT Setup to RxCLK OUT (Figure 11 ) f = 65 MHz 2.5 6.9 ns RHRC RxOUT Hold to RxCLK OUT (Figure 11 ) f = 65 MHz 2.5 5.7 RCCD RxCLK IN to RxCLK OUT Delay at 25C, VCC = 3.3V (Figure 13 ) 5.0 7.1 RPLLS RPDD (1) 4 (Figure 22 ) Min f = 65 MHz 400 ps ns ns 9.0 ns Receiver Phase Lock Loop Set (Figure 15 ) 10 ms Receiver Power Down Delay (Figure 19 ) 1 s Receiver Skew Margin is defined as the valid data sampling region at the receiver inputs. This margin takes into account the transmitter pulse positions (min and max) and the receiver input setup and hold time (internal data sampling window - RSPos). This margin allows for LVDS interconnect skew, inter-symbol interference (both dependent on type/length of cable), and clock jitter (less than 250 ps). Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 DS90C363, DS90CF364 www.ti.com SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 AC Timing Diagrams A. The worst case test pattern produces a maximum toggling of digital circuits, LVDS I/O and CMOS/TTL I/O. B. Figure 4 and Figure 5 show a falling edge data strobe (TxCLK IN/RxCLK OUT). Figure 4. "Worst Case" Test Pattern Device Pin Name Signal TxCLK IN / RxCLK OUT Dot Clk Signal Pattern Signal Frequency f TxIN0 / RxOUT0 R0 f / 16 TxIN1 / RxOUT1 R1 f/8 TxIN2 / RxOUT2 R2 f/4 TxIN3 / RxOUT3 R3 f/2 TxIN4 / RxOUT4 R4 Steady State, Low TxIN5 / RxOUT5 R5 Steady State, Low TxIN6 / RxOUT6 G0 f / 16 TxIN7 / RxOUT7 G1 f/8 TxIN8 / RxOUT8 G2 f/4 TxIN9 / RxOUT9 G3 f/2 TxIN10 / RxOUT10 G4 Steady State, Low TxIN11 / RxOUT11 G5 Steady State, Low TxIN12 / RxOUT12 B0 f / 16 TxIN13 / RxOUT13 B1 f/8 TxIN14 / RxOUT14 B2 f/4 TxIN15 / RxOUT15 B3 f/2 TxIN16 / RxOUT16 B4 Steady State, Low TxIN17 / RxOUT17 B5 Steady State, Low TxIN18 / RxOUT18 HSYNC Steady State, High TxIN19 / RxOUT19 VSYNC Steady State, High TxIN20 / RxOUT20 ENA Steady State, High A. The worst case test pattern produces a maximum toggling of digital circuits, LVDS I/O and CMOS/TTL I/O. B. The 16 grayscale test pattern tests device power consumption for a "typical" LCD display pattern. The test pattern approximates signal switching needed to produce groups of 16 vertical stripes across the display. C. Figure 4 and Figure 5 show a falling edge data strobe (TxCLK IN/RxCLK OUT). D. Recommended pin to signal mapping. Customer may choose to define differently. Figure 5. "16 Grayscale" Test Pattern Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 Submit Documentation Feedback 5 DS90C363, DS90CF364 SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 www.ti.com AC Timing Diagrams (continued) Figure 6. DS90C363 (Transmitter) LVDS Output Load and Transition Times Figure 7. DS90CF364 (Receiver) CMOS/TTL Output Load and Transition Times Figure 8. DS90C363 (Transmitter) Input Clock Transition Time Measurements at Vdiff=0V TCCS measured between earliest and latest LVDS edges TxCLK Differential Low High Edge Figure 9. DS90C363 (Transmitter) Channel-to-Channel Skew Figure 10. DS90C363 (Transmitter) Setup/Hold and High/Low Times 6 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 DS90C363, DS90CF364 www.ti.com SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 AC Timing Diagrams (continued) Figure 11. DS90CF364 (Receiver) Setup/Hold and High/Low Times Figure 12. DS90C363 (Transmitter) Clock In to Clock Out Delay (Falling Edge Strobe) Figure 13. DS90CF364 (Receiver) Clock In to Clock Out Delay Figure 14. DS90C363 (Transmitter) Phase Lock Loop Set Time Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 Submit Documentation Feedback 7 DS90C363, DS90CF364 SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 www.ti.com AC Timing Diagrams (continued) Figure 15. DS90CF364 (Receiver) Phase Lock Loop Set Time Figure 16. Seven Bits of LVDS in One Clock Cycle Figure 17. 21 Parallel TTL Data Inputs Mapped to LVDS Outputs Figure 18. Transmitter Power Down Delay 8 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 DS90C363, DS90CF364 www.ti.com SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 AC Timing Diagrams (continued) Figure 19. Receiver Power Down Delay Figure 20. Transmitter LVDS Output Pulse Position Measurement Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 Submit Documentation Feedback 9 DS90C363, DS90CF364 SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 www.ti.com AC Timing Diagrams (continued) Figure 21. Receiver LVDS Input Strobe Position C--Setup and Hold Time (Internal data sampling window) defined by Rspos (receiver input strobe position) min and max Tppos--Transmitter output pulse position (min and max) RSKM = Cable Skew (type, length) + Source Clock Jitter (cycle to cycle) + ISI (Inter-symbol interference) Cable Skew--typically 10 ps-40 ps per foot, media dependent Cycle-to-cycle jitter is less than 250 ps at 65 MHz. ISI is dependent on interconnect length; may be zero. Figure 22. Receiver LVDS Input Skew Margin 10 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 DS90C363, DS90CF364 www.ti.com SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 PIN DESCRIPTIONS DS90C363 Pin Descriptions -- FPD Link Transmitter Pin Name I/O No. Description TxIN I 21 TTL level input. This includes: 6 Red, 6 Green, 6 Blue, and 3 control lines--FPLINE, FPFRAME and DRDY (also referred to as HSYNC, VSYNC, Data Enable). TxOUT+ O 3 Positive LVDS differentiaI data output. TxOUT- O 3 Negative LVDS differential data output. FPSHIFT IN I 1 TTL Ievel clock input. The falling edge acts as data strobe. Pin name TxCLK IN. R_FB I 1 Programmable strobe select. RTxCLK OUT+ O 1 Positive LVDS differential clock output. TxCLK OUT- O 1 Negative LVDS differential clock output. PWR DWN I 1 TTL level input. When asserted (low input) TRI-STATES the outputs, ensuring low current at power down. V CC I 3 Power supply pins for TTL inputs. GND I 4 Ground pins for TTL inputs. PLL V CC I 1 Power supply pin for PLL. PLL GND I 2 Ground pins for PLL. LVDS V CC I 1 Power supply pin for LVDS outputs. LVDS GND I 3 Ground pins for LVDS outputs. DS90CF364 Pin Descriptions -- FPD Link Receiver Pin Name RxIN+ I/O No. I 3 Positive LVDS differentiaI data inputs. Description RxIN- I 3 Negative LVDS differential data inputs. RxOUT O 21 TTL level data outputs. This includes: 6 Red, 6 Green, 6 Blue, and 3 control lines--FPLINE, FPFRAME, DRDY (also referred to as HSYNC, VSYNC, Data Enable). RxCLK IN+ I 1 Positive LVDS differential clock input. RxCLK IN- I 1 Negative LVDS differential clock input. FPSHIFT OUT O 1 TTL Ievel clock output. The falling edge acts as data strobe. Pin name RxCLK OUT. PWR DWN I 1 TTL level input. When asserted (low input) the receiver outputs are low. V CC I 4 Power supply pins for TTL outputs. GND I 5 Ground pins for TTL outputs. PLL V CC I 1 Power supply for PLL. PLL GND I 2 Ground pin for PLL. LVDS V CC I 1 Power supply pin for LVDS inputs. LVDS GND I 3 Ground pins for LVDS inputs. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 Submit Documentation Feedback 11 DS90C363, DS90CF364 SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 www.ti.com Pin Diagrams Figure 23. DS90C363 See Package Number DGG (R-PDSO-G48) Figure 24. DS90CF364 See Package Number DGG (R-PDSO-G48) Truth Table Table 1. Programmable Transmitter Pin Condition Strobe Status R_FB R_FB = VCC Rising edge strobe R_FB R_FB = GND Falling edge strobe APPLICATIONS INFORMATION The DS90C363 and DS90CF364 are backward compatible with the existing 5V FPD Link transmitter/receiver pair (DS90CF563 and DS90CF564). To upgrade from a 5V to a 3.3V system the following must be addressed: 1. Change 5V power supply to 3.3V. Provide this supply to the VCC, LVDS VCC and PLL V CC of both the transmitter and receiver devices. This change may enable the removal of a 5V supply from the system, and power may be supplied from an existing 3V power source. 2. The DS90C363 (transmitter) incorporates a rise/fall strobe select pin. This select function is on pin 14, formerly a VCC connection on the 5V products. When the rise/fall strobe select pin is connected to V CC, the part is configured with a rising edge strobe. In a system currently using a 5V rising edge strobe transmitter (DS90CR563), no layout changes are required to accommodate the new rise/fall select pin on the 3.3V transmitter. The VCC signal may remain at pin 14, and the device will be configured with a rising edge strobe. - When converting from a 5V falling edge transmitter (DS90CF563) to the 3V transmitter a minimal board layout change is necessary. The 3.3V transmitter will not be configured with a falling edge strobe if VCC remains connected to the select pin. To guarantee the 3.3V transmitter functions with a falling edge strobe pin 14 should be connected to ground OR left unconnected. When not connected (left open) and internal pull-down resistor ties pin 14 to ground, thus configuring the transmitter with a falling edge strobe. 3. The DS90C363 transmitter input and control inputs accept 3.3V TTL/CMOS levels. They are not 5V tolerant. 12 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 DS90C363, DS90CF364 www.ti.com SNLS123C - SEPTEMBER 1999 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision B (April 2013) to Revision C * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 12 Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90C363 DS90CF364 Submit Documentation Feedback 13 PACKAGE OPTION ADDENDUM www.ti.com 12-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) (3) Top-Side Markings (4) DS90C363MTD NRND TSSOP DGG 48 38 TBD Call TI Call TI DS90C363MTD >B DS90C363MTD/NOPB NRND TSSOP DGG 48 38 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR DS90C363MTD >B DS90C363MTDX/NOPB NRND TSSOP DGG 48 1000 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR DS90C363MTD >B DS90CF364MTD/NOPB ACTIVE TSSOP DGG 48 38 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 85 DS90CF364MTD >B DS90CF364MTDX/NOPB ACTIVE TSSOP DGG 48 1000 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 85 DS90CF364MTD >B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 12-Apr-2013 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device DS90C363MTDX/NOPB Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TSSOP DGG 48 1000 330.0 24.4 8.6 13.2 1.6 12.0 24.0 Q1 DS90CF364MTDX/NOPB TSSOP DGG 48 1000 330.0 24.4 8.6 13.2 1.6 12.0 24.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DS90C363MTDX/NOPB TSSOP DGG 48 1000 367.0 367.0 45.0 DS90CF364MTDX/NOPB TSSOP DGG 48 1000 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA MTSS003D - JANUARY 1995 - REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2016, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: DS90C363MTD DS90C363MTD/NOPB DS90C363MTDX/NOPB