TMA25x Series Triac (Bidirectional Triode Thyristor) Features and Benefits Description Exceptional reliability Small fully-molded SIP package with heatsink mounting for high thermal dissipation and long life VDRM of 400 or 600 V 25 ARMS on-state current Uniform switching UL Recognized Component (File No.: E118037) (suffix I) This Sanken triac (bidirectional triode thyristor) is designed for AC power control, providing reliable, uniform switching for full-cycle AC applications. Package: 3-pin SIP (TO-3PF) Applications In comparison with other products on the market, the TMA25x series provides increased isolation voltage (2000 VACRMS), guaranteed for up to 1 minute, and greater peak nonrepetitive off-state voltage, VDSM (700 V). In addition, commutation dv/dt and (dv/dt)c are improved. Residential and commercial appliances: vacuum cleaners, rice cookers, TVs, home entertainment White goods: washing machines Office automation power control, photocopiers Motor control for small tools Temperature control, light dimmers, electric blankets General use switching mode power supplies (SMPS) Not to scale Typical Applications Halogen Lamp Gate Controller Heater control (for example, LBP. PPC, MFP) 28105.09 Two-phase motor control (for example, washing machine) SANKEN ELECTRIC CO., LTD. http://www.sanken-ele.co.jp/en/ In-rush current control (for example, SMPS) TMA25x Series Triac (Bidirectional Triode Thyristor) Selection Guide Part Number VDRM (V) UL-Recognized Component Package Packing 400 400 600 600 Yes - Yes - 3-pin fully molded SIP with heatsink mount 30 pieces per tube TMA254B(I) TMA254B-L TMA256B(I) TMA256B-L Absolute Maximum Ratings Characteristic Symbol Peak Repetitive Off-State Voltage VDRM Peak Non-Repetitive Off-State Voltage VDSM Isolation Voltage VISO RMS On-State Current IT(RMS) Surge On-State Current ITSM I2t Value for Fusing Notes TMA254Bx RGREF = TMA256Bx TMA254Bx RGREF = TMA256Bx AC RMS applied for 1 minute between lead and case Units 400 V 600 V 500 V 700 V 2000 V 50/60 Hz full cycle sine wave, total Conduction angle (+) + (-) = 360, TC = 83C 25 A f = 60 Hz 263 A 250 A Value for 50 Hz half cycle sine wave, 1 cycle, ITSM = 250 A 312 A2 * s Full cycle sine wave, peak value, non-repetitive, initial TJ = 125C f = 50 Hz I2t Rating Critical Rising Rate of On-State Current di/dt IT = IT(RMS) x 2, VD = VDRM x 0.5, f 60 Hz, tgw 100 s, tgr 250 ns, Igp 60 mA 25 A/s Peak Gate Current IGM f 50 Hz, duty cycle 10% 2 A PGM f 50 Hz, duty cycle 10% Peak Gate Power Dissipation Average Gate Power Dissipation PGM(AV) TJ < TJ(max) 5 W 0.5 W Junction Temperature TJ -40 to 125 C Storage Temperature Tstg -40 to 125 C Thermal Characteristics May require derating at maximum conditions Characteristic Symbol Package Thermal Resistance (Junction to Case) RJC Test Conditions For AC Value Units 1.5 C/W Pin-out Diagram T2 Terminal List Table G T1 1 2 3 Number Name 1 T1 Main terminal, gate referenced Function 2 T2 Main terminal connect to signal side 3 G Gate control All performance characteristics given are typical values for circuit or system baseline design only and are at the nominal operating voltage and an ambient temperature, TA, of 25C, unless otherwise stated. 28105.09 SANKEN ELECTRIC CO., LTD. 2 TMA25x Series Triac (Bidirectional Triode Thyristor) ELECTRICAL CHARACTERISTICS Characteristics Symbol Off-State Leakage Current IDRM On-State Voltage VTM Test Conditions Min. Typ. Max. Unit VD = VDRM, TJ = 125C, RGREF = using test circuit 1 - - 2.0 mA VD = VDRM, TJ = 25C, RGREF = using test circuit 1 - - 100 A IT = 20 A, TJ = 25C - - 1.4 V - - 1.5 V V Quadrant I: T2+, G+ Gate Trigger Voltage VGT Gate Trigger Current Quadrant II: T2+, G- IGT VD = 12 V, RL = 20 , TJ = 25C - - 1.5 Quadrant III: T2-, G- - - 1.5 V Quadrant I: T2+, G+ - - 30 mA - - 30 mA - - 30 mA VD = VDRM x 0.5, RL = 4 k, TJ = 125C 0.2 - - V TJ = 125C, VD = 400 V, (di/dt)c = -12 A/ms, ITP = 2 A 15 - - V/s VD = VDRM x 0.66, TJ = 125C, RGREF = using test circuit 1 100 - - V/s Quadrant II: T2+, G- VD = 12 V, RL = 20 , TJ = 25C Quadrant III: T2-, G- Gate Non-trigger Voltage VGD Critical Rising Rate of Off-State Voltage during Commutation* (dv/dt)c Critical Rising Rate of Off-StateVoltage dv/dt *Where ITP is the peak current through T2 to T1. Test Circuit 1 Gate Trigger Characteristics +T2 Quadrant II Quadrant I T2 [ + ] T2 RGREF = T2 [ + ] G[-] G G[+] T1 [ - ] T1 -IGT T1 [ - ] T2 [ - ] T2 [ - ] G[-] G[+] T1 [ + ] Gate Trigger Current +IGT T1 [ + ] Quadrant III -T2 Quadrant IV Polarities referenced to T1 tgr igp tgw 28105.09 SANKEN ELECTRIC CO., LTD. 3 TMA25x Series Triac (Bidirectional Triode Thyristor) Commutation Timing Diagrams Q4 Supply VAC Q A A = Conduction angle VGT VGATE Q ITSM On-State Currrent Q 28105.09 SANKEN ELECTRIC CO., LTD. 4 TMA25x Series Triac (Bidirectional Triode Thyristor) Performance Characteristics at TA = 25C 300 100 f = 50 Hz full cycle sine wave total Conduction angle (A+) + (A-) = 360 initial TJ = 125C 250 TJ = 125C 200 Surge On-State Current versus Quantity of Cycles ITSM (A) Maximum On-State Current versus Maximum On-State Voltage IT (max) (A) 10 TJ = 25C 1 150 100 50 0 0.6 1.4 1.8 VT (max) (V) 1.0 30 0 2.2 TC (C) PT(AV) (W) 100 Case Temperature versus On-State RMS Current 15 83C 75 10 50 5 25 0 100 full cycle sine wave total Conduction angle (A+) + (A-) = 360 125 20 On-State Average Power Dissipation versus Maximum On-State RMS Current 10 Quantity of Cycles 150 full cycle sine wave total Conduction angle (A+) + (A-) = 360 25 1 0 10 20 IT(RMS)(max) (A) 0 30 0 10 20 IT(RMS) (A) 30 2.0 100 Gate Voltage versus Gate Current VG (V) 10 VGM = 10 V PGM =5W VGT (-40C) =2V VGT (25C) = 1.5 V 1 IGT (-40C) = 100 mA IGT (25C) = 30 mA Proportional Change of Typical Trigger Voltage versus Junction Temperature PG(AV) = 0.5 W VGT (TJ) (V) / VGT (TJ = 25C ) (V) 1.8 IGM = 2 A 100 IG (mA) 1000 1.4 1.2 1.0 0.8 0.6 0.4 0.2 VGD = 0.2 V 0.1 10 1.6 0 -60 -40 -20 10 000 0 20 40 60 80 100 120 140 TJ (C) 10 10 Quadrant III (T2-, G-) 1 Quadrant I (T2+, G+) 0.1 -60 -40 -20 0 20 40 60 80 100 120 140 Proportional Change of Typical Holding Current versus Junction Temperature IH (TJ) (A) / IH (TJ = 25C ) (A) Proportional Change of Typical Trigger Current versus Junction Temperature IGT (TJ) (A) / IGT (TJ = 25C ) (A) RGREF = 1 k 1 0.1 -60 -40 -20 TJ (C) 0 20 40 60 80 100 120 140 TJ (C) 28105.09 SANKEN ELECTRIC CO., LTD. 5 TMA25x Series Triac (Bidirectional Triode Thyristor) Transient Thermal Impedence versus Triac Voltage Pulse Duration For AC ZQJC (C/W) 10 1 0.1 0.001 0.01 0.1 1 10 100 QT (s) 28105.09 SANKEN ELECTRIC CO., LTD. 6 TMA25x Series Triac (Bidirectional Triode Thyristor) 5.5 0.2 TO-3PF Package Outline Drawing 15.6 0.2 5.5 0.2 3.45 0.2 9.5 0.2 Gate protrusion 23 0.3 O3.2 0.2 Branding Area XXXXXXXX 3.35 0.2 1.6 XXXXX XXXXX 1.5 4.4 +0.2 1.75 -0.1 +0.2 +0.2 0.65 -0.1 +0.2 1.05 -0.1 (16.2) 3.3 2.15 -0.1 View A View B 5.45 0.1 Terminal dimension at case surface 1 2 3 0.7 MAX View A Gate burr: 0.3 mm (max.), mold flash may appear at opposite side Terminal core material: Cu Terminal treatment: Ni plating and Pb-free solder dip Leadform: 700 Package: TO-3PF (FM100) Dimensions in millimeters 0.7 MAX View B Branding codes (exact appearance at manufacturer discretion): 1st line, type: MA25xB 2nd line left, lot: YM Where: Y is the last digit of the year of manufacture M is the month (1 to 9, O, N, D) 2nd line right, lot: DD Where: DD is the date Leadframe plating Pb-free. Device meets RoHS requirements. 28105.09 SANKEN ELECTRIC CO., LTD. 7 TMA25x Series Triac (Bidirectional Triode Thyristor) Because reliability can be affected adversely by improper storage environments and handling methods, please observe the following cautions. Cautions for Storage * Ensure that storage conditions comply with the standard temperature (5C to 35C) and the standard relative humidity (around 40% to 75%); avoid storage locations that experience extreme changes in temperature or humidity. * Avoid locations where dust or harmful gases are present and avoid direct sunlight. * Reinspect for rust on leads and solderability of the products that have been stored for a long time. Cautions for Testing and Handling When tests are carried out during inspection testing and other standard test periods, protect the products from power surges from the testing device, shorts between the product pins, and wrong connections. Ensure all test parameters are within the ratings specified by Sanken for the products. Remarks About Using Silicone Grease with a Heatsink * When silicone grease is used in mounting the products on a heatsink, it shall be applied evenly and thinly. If more silicone grease than required is applied, it may produce excess stress. * Volatile-type silicone greases may crack after long periods of time, resulting in reduced heat radiation effect. Silicone greases with low consistency (hard grease) may cause cracks in the mold resin when screwing the products to a heatsink. Our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: Type Suppliers G746 Shin-Etsu Chemical Co., Ltd. YG6260 Momentive Performance Materials Inc. SC102 Dow Corning Toray Co., Ltd. Cautions for Mounting to a Heatsink * When the flatness around the screw hole is insufficient, such as when mounting the products to a heatsink that has an extruded (burred) screw hole, the products can be damaged, even with a lower than recommended screw torque. For mounting the products, the mounting surface flatness should be 0.05 mm or less. * Please select suitable screws for the product shape. Do not use a flat-head machine screw because of the stress to the products. Self-tapping screws are not recommended. When using self-tapping screws, the screw may enter the hole diagonally, not vertically, depending on the conditions of hole before threading or the work situation. That may stress the products and may cause failures. * Recommended screw torque: 0.490 to 0.686 Nm (5 to 7 kgfcm). * For tightening screws, if a tightening tool (such as a driver) hits the products, the package may crack, and internal stress fractures may occur, which shorten the lifetime of the electrical elements and can cause catastrophic failure. Tightening with an air driver makes a substantial impact. In addition, a screw torque higher than the set torque can be applied and the package may be damaged. Therefore, an electric driver is recommended. When the package is tightened at two or more places, first pre-tighten with a lower torque at all places, then tighten with the specified torque. When using a power driver, torque control is mandatory. Soldering * When soldering the products, please be sure to minimize the working time, within the following limits: 2605C 101 s (Flow, 2 times) 38010C 3.50.5 s (Soldering iron, 1 time) * Soldering should be at a distance of at least 1.5 mm from the body of the products. Electrostatic Discharge * When handling the products, the operator must be grounded. Grounded wrist straps worn should have at least 1 M of resistance from the operator to ground to prevent shock hazard, and it should be placed near the operator. * Workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. * When using measuring equipment such as a curve tracer, the equipment should be grounded. * When soldering the products, the head of soldering irons or the solder bath must be grounded in order to prevent leak voltages generated by them from being applied to the products. * The products should always be stored and transported in Sanken shipping containers or conductive containers, or be wrapped in aluminum foil. 28105.09 SANKEN ELECTRIC CO., LTD. 8 TMA25x Series Triac (Bidirectional Triode Thyristor) M3 Screw Device Heatsink Flat Washer Typical Mounting Configuration Split Washer M3 Nut 28105.09 SANKEN ELECTRIC CO., LTD. 9 TMA25x Series Triac (Bidirectional Triode Thyristor) * The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the latest revision of the document before use. * Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use. * Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. * Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales representative to discuss, prior to the use of the products herein. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. * In the case that you use Sanken products or design your products by using Sanken products, the reliability largely depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. For these stresses, instantaneous values, maximum values and minimum values must be taken into consideration. In addition, it should be noted that since power devices or IC's including power devices have large self-heating value, the degree of derating of junction temperature affects the reliability significantly. * When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. * Anti radioactive ray design is not considered for the products listed herein. * Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken's distribution network. * The contents in this document must not be transcribed or copied without Sanken's written consent. 28105.09 SANKEN ELECTRIC CO., LTD. 10