VSMP0603 (Z-Foil) Vishay Foil Resistors Ultra High Precision Foil Wraparound Surface Mount Chip Resistor with Temperature Coefficient of Resistance of 0.05 ppm/C, Load Life Stability to 0.005 % (50 ppm) and ESD Immunity up to 25 kV FEATURES Vishay Foil resistors are not restricted to standard values, we can supply specific "as required" values at no extra cost or delivery (e.g. 1K234 vs. 1K). INTRODUCTION VSMP series is the industry's first device to provide high rated power, excellent load life stability along with extremely low TCR all in one resistor. One of the most important parameters influencing stability is the temperature coefficient of resistance (TCR). Although the TCR of foil resistors is considered extremely low, this characteristic has been further refined over the years. The VSMP series utilizes ultra high precision Bulk Metal(R) Z-foil. The Z-foil technology provides a significant reduction of the resistive element's sensitivity to ambient temperature variations (TCR) and to self heating when power is applied (power coefficient). Along with the inherently low PCR and TCR, Z-foil technology also provides remarkably improved load life stability, low noise and availability of tight tolerance. The VSMP0603 has a full wraparound termination which ensures safe handling during the manufacturing process, as well as providing stability during multiple thermal cyclings. Our application engineering department is available to advise and make recommendations. For non-standard technical requirements and special applications, please contact us using the e-mail address in the footer below. TABLE 1 - TOLERANCE AND TCR VS. RESISTANCE VALUE (1) (- 55 C to + 125 C, + 25 C ref.) RESISTANCE VALUE () TOLERANCE (%) APPLICATIONS Automatic test equipment (ATE) High precision instrumentation Laboratory, industrial and medical Audio EB applications (electron beam scanning and recording equipment, electron microscopes) Down hole instrumentation Communication TYPICAL TCR AND MAX. SPREAD (ppm/C) 250to 5K 0.01 0.2 1.8 100to < 250 0.02 0.2 1.8 Note (1) For tighter performances, please contact Vishay application engineering using the e-mail address in the footer below. FIGURE 1 - POWER DERATING CURVE Percent of Rated Power Top View Temperature coefficient of resistance (TCR): 0.05 ppm/C typical (0 C to + 60 C) 0.2 ppm/C typical (- 55 C to + 125 C, + 25 C ref.) Tolerance: to 0.01 % Power coefficient "R due to self heating": 5 ppm at rated power Power rating: to 100 mW at + 70 C Load life stability: to 0.005 % at 70 C, 2000 h at rated power Resistance range: 100 to 5 k Electrostatic discharge (ESD) up to 25 000 V Short time overload: 0.005 % Non inductive, non capacitive design Rise time: 1 ns effectively no ringing Special design which reduces circuit signal distortion Current noise: - 40 dB Voltage coefficient < 0.1 ppm/V Non inductive: < 0.08 H Non hot spot design Terminal finishes available: lead (Pb)-free tin/lead alloy Matched sets are available on request Prototype samples available from 72 h. For more information, please contact foil@vishaypg.com For better performances please contact us + 70 C - 55 C 100 75 50 25 0 - 75 - 50 - 25 0 + 25 + 50 + 75 + 100 + 125 + 150 + 175 Ambient Temperature (C) * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 63141 Revision: 26-Mar-10 For any questions, contact: foil@vishaypg.com www.foilresistors.com 1 VSMP0603 (Z-Foil) Vishay Foil Resistors FIGURE 2 - TRIMMING TO VALUES (Conceptual Illustration) FIGURE 3 -TYPICAL TCR CURVE Z-FOIL + 500 + 400 + 300 + 200 Current Path Before Trimming Interloop Capacitance Reduction in Series + 100 R 0 R (ppm) - 100 Current Path After Trimming Trimming Process Removes this Material from Shorting Strip Area Changing Current Path and Increasing Resistance Mutual Inductance Reduction due to Opposing Current in Adjacent Lines 0.05 ppm/C - 200 - 0.1 ppm/C - 300 0.1 ppm/C 0.14 ppm/C - 400 0.2 ppm/C - 0.16 ppm/C - 500 - 55 - 25 0 + 25 + 60 + 75 + 100 + 125 Ambient Temperature (C) Note * The TCR values for < 100 are influenced by the termination composition and result in deviation from this curve. Note: Foil shown in black, etched spaces in white TABLE 2 - DIMENSIONS AND LAND PATTERN in Inches (Millimeters) Bottom View for Mounting Uncoated Ceramic L W T D CHIP SIZE 0603 L 0.005 (0.13) W 0.005 (0.13) THICKNESS MAXIMUM D 0.005 (0.13) 0.063 (1.60) 0.032 (0.81) 0.025 (0.64) 0.011 (0.28) Note * Land pattern dimensions are per IPC-782. TABLE 3 - PERFORMANCES TEST OR CONDITIONS PER MIL-PRF-55342 MIL-PRF-55342 CHARACTERISTIC E R LIMITS TYPICAL R LIMITS MAXIMUM R LIMITS Thermal shock: 100 x (- 65 C to + 150 C) 0.2 % 0.005 % (50 ppm) 0.01 % (100 ppm) Low temperature operation: - 65 C, 45 min, rated power 0.1 % 0.005 % (50 ppm) 0.01 % (100 ppm) Short time overload: 6.25 x rated power, 5 s 0.1 % 0.005 % (50 ppm) 0.01 % (100 ppm) High temperature exposure: 100 h, 150 C 0.1 % 0.01 % (100 ppm) 0.03 % (300 ppm) Resistance to soldering heat 0.2 % 0.005 % (50 ppm) 0.02 % (200 ppm) Moisture resistance 0.2 % 0.03 % (300 ppm) 0.1 % (1000 ppm) Load life stability + 70 C for 2000 h at rated power 0.5 % 0.005 % (50 ppm) 0.01 % (100 ppm) Note * As shown + 0.01 to allow for measurement errors at low values. www.foilresistors.com 2 For any questions, contact: foil@vishaypg.com Document Number: 63141 Revision: 26-Mar-10 VSMP0603 (Z-Foil) Vishay Foil Resistors FIGURE 4 - VSMP0603 100 CYCLE THERMAL SHOCK - 65 C TO 150 C, 10 UNITS EACH VALUE 100 80 R/R (ppm) 60 40 20 0 - 20 - 40 VSMP0603 100R VSMP0603 1K VSMP0603 5K FIGURE 5 - LOAD LIFE STABILITY 2000 h AT + 70 C, 0.1 W, 20 UNITS EACH VALUE 60 50 R/R (ppm) 40 30 20 10 0 - 10 VSMP0603 100R VSMP0603 1K VSMP0603 5K FIGURE 6 - RECOMMENDED MOUNTING 25 % to 85 % of T A low profile solder fillet is recommended to avoid unnecessary stresses along top edge of metallization. IR and vapor phase reflow are best. Avoid the use of cleaning agents which could attack epoxy resins, which form part of the resistor construction. Notes (1) Avoid the use of cleaning agents which could attack epoxy resins, which form part of the resistor construction (2) Vacuum pick up is recommended for handling (3) Soldering iron may damage the resistor Document Number: 63141 Revision: 26-Mar-10 For any questions, contact: foil@vishaypg.com www.foilresistors.com 3 VSMP0603 (Z-Foil) Vishay Foil Resistors TABLE 4 - GLOBAL PART NUMBER INFORMATION NEW GLOBAL PART NUMBER: Y16363K25200T9R (preferred part number format) DENOTES PRECISION VALUE CHARACTERISTICS (1) Y R= K = k 0 = standard part, tin/lead termination 9 = standard part, lead (Pb)-free termination 1 to 999 = custom Y 1 6 3 6 3 K 2 5 2 0 0 T 9 PRODUCT CODE RESISTANCE TOLERANCE PACKAGING 1636 = VSMP0603 T = 0.01 % Q = 0.02 % A = 0.05 % B = 0.10 % C = 0.25 % D = 0.5 % F = 1.0 % R = tape and reel W = waffle pack R FOR EXAMPLE: ABOVE GLOBAL ORDER Y1636 3K25200 T 9 R: TYPE: VSMP0603 VALUES: 3.252 k ABSOLUTE TOLERANCE: 0.01 % TERMINATION: lead (Pb)-free PACKAGING: tape and reel Note (1) For non-standard requests, please contact application engineering. www.foilresistors.com 4 For any questions, contact: foil@vishaypg.com Document Number: 63141 Revision: 26-Mar-10 Legal Disclaimer Notice Vishay Precision Group Disclaimer ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE. Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay Precision Group"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. The product specifications do not expand or otherwise modify Vishay Precision Group's terms and conditions of purchase, including but not limited to, the warranty expressed therein. Vishay Precision Group makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase. To the maximum extent permitted by applicable law, Vishay Precision Group disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Information provided in datasheets and/or specifications may vary from actual results in different applications and performance may vary over time. Statements regarding the suitability of products for certain types of applications are based on Vishay Precision Group's knowledge of typical requirements that are often placed on Vishay Precision Group products. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any conduct of Vishay Precision Group. The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay Precision Group products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay Precision Group for any damages arising or resulting from such use or sale. Please contact authorized Vishay Precision Group personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document No.: 63999 Revision: 27-Apr-2011 www.vishaypg.com 1