Ceramic Core Chip Inductors CC10 A Dimensions (In.) CC10 A B C D E F G H I .115 Max. .110 Max. .083 Max. .020 .004 .080 .004 .015 .004 .050 .040 .100 D Inductance Tolerance Test (nh) (%) Freq. (MHz) I F E Allied Part Number C B Q Min. Test Freq. (MHz) SRF Min. (MHz) DCR Max. () Rated Current (mA) CC10-4N7K 4.7 10 50 50 500 4100 0.08 1000 CC10-10NK 10 10 50 50 500 4100 0.08 1000 CC10-12NK 12 10 50 50 500 3300 0.09 1000 CC10-15NK 15 10 50 50 500 3000 0.10 1000 CC10-18NK 18 10 50 50 350 2500 0.11 1000 CC10-22NJ 22 5 50 55 350 2400 0.12 1000 CC10-27NJ 27 5 50 55 350 1600 0.13 1000 CC10-33NJ 33 5 50 60 350 1600 0.14 1000 CC10-39NJ 39 5 50 60 350 1500 0.15 1000 CC10-47NJ 47 5 50 65 350 1500 0.16 1000 CC10-56NJ 56 5 50 65 350 1300 0.18 1000 CC10-68NJ 68 5 50 65 350 1300 0.20 1000 CC10-82NJ 82 5 50 60 350 1000 0.22 1000 CC10-100NJ 100 5 25 60 350 1000 0.56 800 CC10-120NJ 120 5 25 60 350 950 0.63 800 CC10-150NJ 150 5 25 45 100 850 0.70 800 CC10-180NJ 180 5 25 45 100 750 0.77 750 CC10-220NJ 220 5 25 45 100 700 0.84 720 CC10-270NJ 270 5 25 45 100 600 0.91 690 CC10-330NJ 330 5 25 45 100 570 1.05 660 CC10-390NJ 390 5 25 45 100 500 1.12 630 CC10-470NJ 470 5 25 45 100 450 1.19 600 CC10-560NJ 560 5 25 45 100 415 1.33 580 CC10-620NJ 620 5 25 45 100 375 1.40 560 CC10-680NJ 680 5 25 45 100 375 1.47 540 CC10-750NJ 750 5 25 45 100 360 1.54 520 CC10-820NJ 820 5 25 45 100 350 1.61 500 CC10-910NJ 910 5 25 35 50 320 1.68 480 CC10-1000NJ 1000 5 25 35 50 290 1.75 460 CC10-1200NJ 1200 5 7.9 35 50 250 2.0 440 CC10-1500NJ 1500 5 7.9 28 50 200 2.3 420 CC10-1800NJ 1800 5 7.9 28 50 160 2.6 400 CC10-2200NJ 2200 5 7.9 28 50 160 2.8 380 CC10-2700NJ 2700 5 7.9 22 25 140 3.2 360 CC10-3300NJ 3300 5 7.9 22 25 110 3.4 350 CC10-3900NJ 3900 5 7.9 20 25 100 3.6 340 CC10-4700NJ 4700 5 7.9 20 25 90 4.0 330 G H Electrical Dielectric Withstanding Voltage: 5 seconds at DC 500 V applied between both terminals and film. Insulation Resistance: 1000M and over. 1 Minute at DC 100 V measured between both terminals and film. Flammability: IEC 695-2-2. Withstands needle-flame test. Tolerance: For 20% use M, 10% use K, 5% use J and 2% use G as part number suffix. Mechanical Terminal Pull Strength: Terminals shall withstand a pull of 10N in a horizontal direction. Terminal Bending Strength: Specimen shall be soldered of bend test board and force applied to the opposite side to cause a 10 mm deflection. Vibration: L/L within 5%. Q/Q within 10%. 2 hours in each direction of X,Y, Z< on PCB at a frequency range of 10-55 10MHz with 1.5 mm amplitude. Dropping: L/L within 5%. Q/Q within 10%. Dropping 1 m on the ground of concrete 1 time. Resistance to Soldering Heat: L/L within 5%. Q/Q within 10%. Immerse the solder at 260 5C for 10 1 seconds. Solderability: 95% of the terminal should be covered with new solder. Immerse in the solder at 230 5C for 10 1 seconds. Resistance to Solvent: Accordance with MILSTD-202F Method 215. Environmental Characteristics L/L within 5%. Q/Q within 10%. Low Temperature Storage: Store at -40 2C, for 1000 hours. High Temperature Storage: Store at +125 2C, for 1000 hours. Moisture Endurance: Store at 45 2C, 90~ 95% RH for 1000 hours. Load Life: Biased to full rated current at 125C for 1000 hours. High Temperature/High Humidity: Biased to 10% rated current at 85C, 85% RH for 1000 hours. Thermal Shock: 100 cycles between 40C/hour and +125C/hour. Temperature Characteristics: L/L to be measured at the temperature of between -40C and +125C as based on the inductance at 20C. Physical Packaging: 2000 pieces per 7 inch reel. All specifications subject to change without notice. ALLIED COMPONENTS INTERNATIONAL 14712 SINCLAIR CIRCLE TUSTIN, CALIFORNIA 92780 714/665-1140 800/295-3800 FAX 714/665-1150 5