0.25-6.0 GHz High Dynamic Range Amplifier CMM6004-AH February 2007 - Rev 10-Feb-07 Features Functional Block Diagram 0.25 to 6.0 GHz Frequency Range +41 dBm Output IP3 1.7 dB Noise Figure 15 dB Gain +23 dBm P1dB LGA Package Single Power Supply Single Input Matching Pin 1 INPUT OUTPUT (BIAS) ALL OTHER PINS GROUNDED Description The CMM6004-AH is a high dynamic range amplifier designed for applications operating within the 0.25 to 6.0 GHz frequency range. It is an ideal solution for numerous transmit and receive functions in wireless local loop (WLL) and UNH applications where high linearity is required. The amplifier has the flexibility of being optimized for a number of wireless applications. It is an ideal solution when used as a driver amplifier in applications including cellular and PCS (personal communications services) operating from 0.8 to 2.2 GHz; MMDS (multichannel multipoint distribution systems) operating from 2.2 to 2.7 GHz; WLAN (wireless LAN) operating at 2.4 GHz; WLL (wireless local loop) operating at 3.5 GHz; and HiperLAN (high performance LAN) and U-NII (unlicensed national information infrastructure) operating from 5.0 to 6.0 GHz. The CMM6004-AH is packaged in a low-cost, space efficient, Land Grid Array (LGA) package which provides excellent electrical stability and low thermal resistance. All devices are 100% RF and DC tested. With single input matching the part simplifies design by keeping board space and cost to a minimum. Absolute Maximum Ratings Supply Voltage RF Input Power* Storage Temperature Junction Temperature Operating Temperature Thermal Resistance +6.0 V +20 dBm -55C to 125C 150C -40C to +85C 50C/W Operation of this device above any of these parameters may cause permanent damage. *Operation with more than 10 dBm of RF input power may cause 2 dB degradation in OIP3 performance. Applications Wireless Local Loop Transmit and Receive UNH Transmit and Receive Dual Band 802.11 WLAN WiMAX LAN Electrical Characteristics (T=25C) Unless otherwise specified, the following specifications are guaranteed at room temperature in a Mimix test fixture. Parameter Condition Frequency Range Gain Externally matched Input Return Loss Externally matched Output IP3 Noise Figure Output P1dB Operating Current Range Supply Voltage Min 0.25 13.5 38 120 Typ Max Units 6.0 15 -10 41 1.7 23.0 150 5.0 180 GHz dB dB dBm dB dBm mA V Notes: 1. T = 25C, Vdd = 5V, Frequency = 2 GHz, 50 Ohm system. 2. OIP3 measured with two tones at output power of 5 dBm/tone separated by 10 MHz. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 1 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.25-6.0 GHz High Dynamic Range Amplifier CMM6004-AH February 2007 - Rev 10-Feb-07 Application Circuit (836 MHz) 836 MHz 18 dB -23 dB -14 dB 40 dBm 1.75 dB Vds = 5V, Id = 175 mA CMM6004-AH RF IN C1 100 pF T1 50 ? 20 L2 22 nH L1 6.8 nH INPUT MATCHING NETWORK RF OUT T1 50 ? 30 uuuu Frequency Gain Input Return Loss Output Return Loss OIP3 Noise Figure Bias 836 MHz uuuu Typical Performance (50 Ohm System) C2 1.0 pF Vcc 5V C3 4.7 pF C4 100 pF OUTPUT MATCHING NETWORK Circuit Board Parts List Part Type Reference Designator Description Inductor Inductor Capacitor Capacitor Capacitor L1 L2 C1, C4 C2 C3 0603, 6.8 nH 0603, 22 nH SMD 0805 NPO, 100 pF 0603, 1 pF SMD 0805, 50V 0.25 pF 4.7 pF Typical Performance IP3 measured with 2 tones at an output power of 5 dBm/tone separated by 10 MHz Gain, Input Return Loss and Output Return Loss vs Frequency Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 2 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.25-6.0 GHz High Dynamic Range Amplifier CMM6004-AH February 2007 - Rev 10-Feb-07 Application Circuit (2.1 GHz) 2.1 GHz 15.8 dB -14 dB -16.5 dB 40 dBm 2.95 dB Vds = 5V, Id = 175 mA CMM6004-AH RF IN RF OUT T1 50 ? 33 C1 100 pF uuuu Frequency Gain Input Return Loss Output Return Loss OIP3 Noise Figure Bias 2.1 GHz uuuu Typical Performance (50 Ohm System) L2 22 nH L1 1.8 nH INPUT MATCHING NETWORK C2 1.0 pF Vcc 5V C3 1.5 pF C4 100 pF OUTPUT MATCHING NETWORK Circuit Board Parts List Part Type Reference Designator Description Inductor Inductor Capacitor Capacitor Capacitor L1 L2 C1, C4 C2 C3 0603, 0.3, 1.8 nH 0603, 22 nH SMD 0805 NPO, 100 pF 0603, 1 pF SMD 0603, 50V 0.1 pF 1.5 pF Typical Performance IP3 measured with 2 tones at an output power of 5 dBm/tone separated by 10 MHz Gain, Input Return Loss and Output Return Loss vs Frequency Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 3 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.25-6.0 GHz High Dynamic Range Amplifier CMM6004-AH February 2007 - Rev 10-Feb-07 Application Circuit (5.8 GHz) Typical Performance (50 Ohm System) 5.8 GHz CMM6004-AH 5.8 GHz 10.5 dB -11.5 dB -17.2 dB 40 dBm 3.8 dB Vds = 5V, Id = 175 mA T1 50 ? 110 RF IN C1 100 pF T1 50 ? 125 C2 3.9 pF C4 100 pF RF OUT uuuu Frequency Gain Input Return Loss Output Return Loss OIP3 Noise Figure Bias L1 6.8 nH INPUT MATCHING NETWORK C3 1.0 pF Vcc 5V Circuit Board Parts List Part Type Reference Designator Description Inductor Capacitor Capacitor Capacitor L1 C1, C4 C2 C3 0603, 6.8 nH SMD 0805 NPO, 100 pF SMD 0805, 3.9 pF 0603, 1 pF Typical Performance Gain vs Temperature @ 5.8 GHz IP3 measured with 2 tones at an output power of 5 dBm/tone separated by 10 MHz IP3 vs Temperature @ 5.8 GHz Gain, Input Return Loss and Output Return Loss vs Frequency Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.25-6.0 GHz High Dynamic Range Amplifier CMM6004-AH February 2007 - Rev 10-Feb-07 Physical Dimensions Dimensions in millimeters/inches Mounting Recommendation *Board substrate: RO-4003 Thickness = 31 mil *Ground vias are critical to RF and thermal grounding considerations. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 5 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 0.25-6.0 GHz High Dynamic Range Amplifier CMM6004-AH February 2007 - Rev 10-Feb-07 Handling and Assembly Information CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: Do not ingest. Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high volume solder installation. Care should be taken not to apply heavy pressure to the top or base material to avoid package damage. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress. Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matt tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260C reflow) "Pb Free" processes. Ordering Information Part Number for Ordering CMM6004-AH-0000 CMM6004-AH-000T PB-CMM6004-AH-00A0 PB-CMM6004-AH-00B0 PB-CMM6004-AH-00C0 Package RoHS compliant LGA surface-mount power package in bulk quantity RoHS compliant LGA surface-mount power package in tape and reel Evaluation Board with SMA connectors for 900 MHz Evaluation Board with SMA connectors for 1.9 GHz Evaluation Board with SMA connectors for 5.8 GHz We also offer this product with SnPb (Tin-Lead) or NiPdAu plating. Please contact your regional sales manager for more information regarding different plating types. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 6 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2007 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.