LMC567 Low Power Tone Decoder General Description Features The LMC567 is a low power general purpose LMCMOSTM tone decoder which is functionally similar to the industry standard LM567. It consists of a twice frequency voltagecontrolled oscillator (VCO) and quadrature dividers which establish the reference signals for phase and amplitude detectors. The phase detector and VCO form a phaselocked loop (PLL) which locks to an input signal frequency which is within the control range of the VCO. When the PLL is locked and the input signal amplitude exceeds an internally pre-set threshold, a switch to ground is activated on the output pin. External components set up the oscillator to run at twice the input frequency and determine the phase and amplitude filter time constants. n n n n n n n n n n Block Diagram Functionally similar to LM567 2V to 9V supply voltage range Low supply current drain No increase in current with output activated Operates to 500 kHz input frequency High oscillator stability Ground-referenced input Hysteresis added to amplitude comparator Out-of-band signals and noise rejected 20 mA output current capability (with External Components) 00867001 Order Number LMC567CM or LMC567CN See NS Package Number M08A or N08E LMCMOSTM is a trademark of National Semiconductor Corp. (c) 2004 National Semiconductor Corporation DS008670 www.national.com LMC567 Low Power Tone Decoder June 1999 LMC567 Absolute Maximum Ratings (Note 1) Storage Temperature Range If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Soldering Information Input Voltage, Pin 3 -55C to +150C Dual-In-Line Package Soldering (10 sec.) 2 Vp-p 260C Small Outline Package Supply Voltage, Pin 4 10V Vapor Phase (60 sec.) 215C Output Voltage, Pin 8 13V Infrared (15 sec.) 220C Voltage at All Other Pins Vs to Gnd Output Current, Pin 8 See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" for other methods of soldering surface mount devices. 30 mA Package Dissipation 500 mW Operating Temperature Range (TA) -25C to +125C Electrical Characteristics Test Circuit, TA = 25C, Vs = 5V, RtCt #2, Sw. 1 Pos. 0, and no input, unless otherwise noted. Symbol I4 Parameter Power Supply Current Conditions Min RtCt #1, Quiescent or Activated Typ Max Units 0.5 0.8 mAdc 0.8 1.3 Vs = 2V 0.3 Vs = 5V Vs = 9V V3 Input D.C. Bias 0 mVdc R3 Input Resistance 40 k I8 Output Leakage f0 Center Frequency, Fosc / 2 1 RtCt #2, Measure Oscillator Frequency and Divide by 2 Vs = 2V Vs = 5V 92 Vs = 9V f0 Vin Set Input Frequency Equal to f0 Measured Above, Increase Input Level Until Pin 8 Goes Low. Vin Input Hysteresis Starting at Input Threshold, Decrease Input Level Until Pin 8 goes High. V8 Output "Sat' Voltage Input Level > Threshold Choose RL for Specified I8 L.D.B.W. Largest Detection Bandwidth Measure Fosc with Sw. 1 in Pos. 0, 1, and 2; Vs = 2V 11 Vs = 5V 17 Vs = 9V 113 kHz 1.0 2.0 %/V 20 27 30 45 103 mVrms 45 1.5 I8 = 2 mA 0.06 I8 = 20 mA 0.7 mVrms 0.15 Vdc Vs = 2V 7 11 15 Vs = 5V 11 14 17 % 1.0 % Vs = 9V BW nAdc 105 Center Frequency Shift with Supply Input Threshold 100 98 15 Bandwidth Skew 0 fmax Highest Center Freq. RtCt #3, Measure Oscillator Frequency and Divide by 2 Vin Input Threshold at fmax Set Input Frequency Equal to fmax measured Above, Increase Input Level Until Pin 8 goes Low. 700 35 kHz mVrms Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. www.national.com 2 LMC567 Test Circuit 00867002 RtCt Rt Ct #1 100k 300 pF #2 10k 300 pF #3 5.1k 62 pF 3 www.national.com LMC567 Typical Performance Characteristics Supply Current vs. Operating Frequency Bandwidth vs. Input Signal Level 00867003 00867007 Largest Detection Bandwidth vs. Temp. Bandwidth as a Function of C2 00867008 00867009 Frequency Drift with Temperature Frequency Drift with Temperature 00867010 www.national.com 00867011 4 SUPPLY DECOUPLING The decoupling of supply pin 4 becomes more critical at high supply voltages with high operating frequencies, requiring C4 to be placed as close as possible to pin 4. (refer to Block Diagram) GENERAL The LMC567 low power tone decoder can be operated at supply voltages of 2V to 9V and at input frequencies ranging from 1 Hz up to 500 kHz. INPUT PIN The input pin 3 is internally ground-referenced with a nominal 40 k resistor. Signals which are already centered on 0V may be directly coupled to pin 3; however, any d.c. potential must be isolated via a coupling capacitor. Inputs of multiple LMC567 devices can be paralleled without individual d.c. isolation. The LMC567 can be directly substituted in most LM567 applications with the following provisions: 1. Oscillator timing capacitor Ct must be halved to double the oscillator frequency relative to the input frequency (See OSCILLATOR TIMING COMPONENTS). 2. Filter capacitors C1 and C2 must be reduced by a factor of 8 to maintain the same filter time constants. 3. The output current demanded of pin 8 must be limited to the specified capability of the LMC567. LOOP FILTER Pin 2 is the combined output of the phase detector and control input of the VCO for the phase-locked loop (PLL). Capacitor C2 in conjunction with the nominal 80 k pin 2 internal resistance forms the loop filter. OSCILLATOR TIMING COMPONENTS For small values of C2, the PLL will have a fast acquisition time and the pull-in range will be set by the built in VCO frequency stops, which also determine the largest detection bandwidth (LDBW). Increasing C2 results in improved noise immunity at the expense of acquisition time, and the pull-in range will begin to become narrower than the LDBW (see Bandwidth as a Function of C2 curve). However, the maximum hold-in range will always equal the LDBW. The voltage-controlled oscillator (VCO) on the LMC567 must be set up to run at twice the frequency of the input signal tone to be decoded. The center frequency of the VCO is set by timing resistor Rt and timing capacitor Ct connected to pins 5 and 6 of the IC. The center frequency as a function of Rt and Ct is given by: OUTPUT FILTER Pin 1 is the output of a negative-going amplitude detector which has a nominal 0 signal output of 7/9 Vs. When the PLL is locked to the input, an increase in signal level causes the detector output to move negative. When pin 1 reaches 2/3 Vs the output is activated (see OUTPUT PIN). Capacitor C1 in conjunction with the nominal 40 k pin 1 internal resistance forms the output filter. The size of C1 is a tradeoff between slew rate and carrier ripple at the output comparator. Low values of C1 produce the least delay between the input and output for tone burst applications, while larger values of C1 improve noise immunity. Pin 1 also provides a means for shifting the input threshold higher or lower by connecting an external resistor to supply or ground. However, reducing the threshold using this technique increases sensitivity to pin 1 carrier ripple and also results in more part to part threshold variation. Since this will cause an input tone of half Fosc to be decoded, This equation is accurate at low frequencies; however, above 50 kHz (Fosc = 100 kHz), internal delays cause the actual frequency to be lower than predicted. The choice of Rt and Ct will be a tradeoff between supply current and practical capacitor values. An additional supply current component is introduced due to Rt being switched to Vs every half cycle to charge Ct: Is due to Rt = Vs/(4Rt) Thus the supply current can be minimized by keeping Rt as large as possible (see supply current vs. operating frequency curves). However, the desired frequency will dictate an RtCt product such that increasing Rt will require a smaller Ct. Below Ct = 100 pF, circuit board stray capacitances begin to play a role in determining the oscillation frequency which ultimately limits the minimum Ct. To allow for I.C. and component value tolerances, the oscillator timing components will require a trim. This is generally accomplished by using a variable resistor as part of Rt, although Ct could also be padded. The amount of initial frequency variation due to the LMC567 itself is given in the electrical specifications; the total trim range must also accommodate the tolerances of Rt and Ct. OUTPUT PIN The output at pin 8 is an N-channel FET switch to ground which is activated when the PLL is locked and the input tone is of sufficient amplitude to cause pin 1 to fall below 2/3 Vs. Apart from the obvious current component due to the external pin 8 load resistor, no additional supply current is required to activate the switch. The on resistance of the switch is inversely proportional to supply; thus the "sat" voltage for a given output current will increase at lower supplies. 5 www.national.com LMC567 Applications Information LMC567 Physical Dimensions inches (millimeters) unless otherwise noted Molded Small Outline (SO) Package (M) Order Number LMC567CM NS Package Number M08A Molded Dual-In-Line Package (N) Order Number LMC567CN NS Package Number N08E www.national.com 6 LMC567 Low Power Tone Decoder Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560