FUJITSU MICROELECTRONICS DATA SHEET DS07-12547-7E 8-bit Microcontroller CMOS F2MC-8L MB89530A Series MB89535A/537A/537AC/538A/538AC/F538 MB89F538L/P538/PV530 DESCRIPTION The MB89530A series is a one-chip microcontroller featuring the F2MC-8L core supporting low-voltage and highspeed operation. Built-in peripheral functions include timers, serial interface, A/D converter, and external interrupt. This product is an ideal general-purpose one-chip microcontroller for a wide variety of applications from household to industrial equipment, as well as use in portable devices. Note : F2MC is the abbreviation of FUJITSU Flexible Microcontroller. FEATURES * Wide range of package options * QFP package (1.00 mm pitch) * Two types of LQFP packages (0.65 mm pitch, 0.50 mm pitch) * SH-DIP package (1.778 mm pitch) * BCC package (0.50 mm pitch) * Low voltage, high-speed operating capability Minimum instruction execution time 0.32 s (at base oscillator 12.5 MHz) * F2MC-8L CPU Core * Instruction set optimized for controller operation * Multiplication/division instructions * 16-bit calculation * Branching instructions with bit testing * Bit operation instructions, etc. (Continued) For the information for microcontroller supports, see the following web site. http://edevice.fujitsu.com/micom/en-support/ Copyright(c)2001-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved 2008.10 MB89530A Series (Continued) * Five timer systems * 8-bit PWM timer with 2 channels (usable as either interval timer of PWM timer) * Pulse width count timer (supports continuous measurement or remote control receiving applications) * 16-bit timer counter * 21-bit time base timer * Watch prescaler (17-bit) * UART Synchronous or asynchronous operation, switchable * 2 serial interfaces (Serial I/O) Selection of transfer direction (specify MSB first or LSB first) for communication with a variety of devices * 10-bit A/D converter (8 channels) * External clock input for startup support * Time base timer output for startup support (except MB89F538/F538L) * Pulse generators (PPG) with 2-program capability * 6-bit PPG with selection of pulse width and pulse period * 12-bit PPG (2 channels) with selection of pulse width and pulse period * I2C interface circuits * External interrupt 1 (single-clock system : 4 channels, dual-clock system : 3 channels) 4 or 3 independent inputs, release enabled from standby mode (includes edge detection function) * External interrupt 2 (except for MB89F538/F538L : 8 channels, MB89F538/F538L : 7 channels) 8 or 7 independent input, release enabled form standby mode (includes level edge detection function) * Standby modes (low power consumption modes) * Stop mode (oscillator stops, virtually no power consumed) * Sleep mode (CPU stops, power consumption reduced to one-third) * Sub clock mode * Watch mode * Watchdog timer reset * I/O ports * Maximum ports Single-clock system : Except MB89F538/F538L 53 ports MB89F538/F538L 52 ports Dual-clock system : Except MB89F538/F538L 51 ports : MB89F538/F538L 50 ports * 38 general-purpose I/O ports (CMOS) (MB89F538/F538L : 37 general-purpose I/O ports) * 2 general-purpose I/O ports (N-ch open drain) * 8 general-purpose output ports (N-ch open drain) * General-purpose input ports (CMOS) : single-clock system : 5 ports, dual-clock system : 3 ports 2 DS07-12547-7E MB89530A Series PRODUCT LINEUP Part number Parameter Type MB89535A MB89537A/ MB89538A/ 537AC 538AC Mass produced (MASK ROM) MB89F538/ MB89F538L MB89P538 MB89PV530 Flash product One-time programmable product Evaluation product ROM capacity 48 Kbytes x 48 Kbytes x 8-bit 8-bit 16 Kbytes x 32 Kbytes x 48 Kbytes x (built-in ROM) 48 Kbytes x 8-bit (built-in Flash) 8-bit 8-bit 8-bit (external ROM) *2 (write from (write from (built-in (built-in (built-in general purpose general purpose ROM) ROM) ROM) EPROM writer) EPROM writer) RAM capacity 512 bytes x 8-bit Operating voltage MB89F538 : 3.5 V to 5.5 V 2.2 V to 5.5 V *1 (MB89535A/537A/538A/537AC/538AC) MB89F538L : 2.4 V to 3.6 V *1 CPU functions Basic instructions Instruction bit length Instruction length Data bit length Minimum instruction execution time Minimum interrupt processing time 1 Kbyte x 8-bit 2 Kbytes x 8-bit 2.7 V to 5.5 V 2.7 V to 5.5 V : 136 : 8 bits : 1 bit to 3 bits : 1, 8, 16 bits : 0.32 s / 12.5 MHz : 2.88 s / 12.5 MHz Peripheral functions Input ports Ports : single-clock system : 5 (4 also usable as external interrupts) dual-clock system : 3 (3 also usable as external interrupts) Output-only ports (N-ch open drain) : 8 (8 also usable as A/D converter input) I/O ports (N-ch open drain) : 2 (2 also usable as SO2/SDA or SI2/SCL) I/O ports (CMOS) (Except MB89F538/F538L) : 38 I/O ports (CMOS) (MB89F538/F538L) : 37 (21 have no other function) Total (except MB89F538/F538L) : single-clock system : 53 dual-clock system : 51 Total (MB89F538/F538L) : single-clock system : 52 dual-clock system : 50 Time base timer 21 bits Interrupt periods at main clock oscillation frequency of 12.5 MHz (approx. 0.655 ms, 2.621 ms, 20.97 ms, 335.5 ms) Watchdog timer Reset period of approx. 167.8 ms to 335.6 ms at main clock frequency of 12.5 MHz Reset period of approx. 500 ms to 1000 ms at sub clock frequency of 32.768 kHz. PWM timer 8-bit interval timer operation (supports square wave output, operating clock period : 1, 8, 16, 64 tinst*3) Pulse width measurement with 8-bit resolution (conversion period : 28 tinst*3 to 28 x 64 tinst*3) 2 channels (can also be used as interval timer, can also be used as ch.1 output and ch.2 count clock) Watch prescaler Interval times at 17-bit sub clock base frequency of 32.768 kHz (approx. 31.25 ms, 0.25 s, 0.50 s, 1.00 s, 2.00 s, 4.00 s) (Continued) DS07-12547-7E 3 MB89530A Series (Continued) Part number Peripheral functions Parameter MB89535A MB89537A/ 537AC MB89538A/ 538AC MB89F538/ MB89F538L MB89P538 MB89PV530 Pulse width count timer 8-bit one-shot timer operation (supports underflow output, operating clock period : 1, 4, 32 tinst*3, external) 8-bit reload timer operation (supports square wave output, operating clock period : 1, 4, 32 tinst*3, external) 8-bit pulse width measurement operation (continuous measurement, "H" width measurement, "L" width measurement, to , to , "H" width measurement and to) 16-bit timer/ counter 16-bit timer operation (operating clock period : 1 tinst*3, external) 16-bit event counter operation (select rising, falling, or both edges) 16-bit x 1 channel Serial I/O 8 bits length Selection of LSB first or MSB first Transfer clock (2, 8, 32 tinst*3, external) UART/SIO CLK synchronous/CLK asynchronous data transfer capability (8, 9-bit with parity bit, or 7,8-bit without parity bit) . Built-in baud rate generator provides selection of 14 baud rate settings. UART CLK synchronous/CLK asynchronous data transfer capability (4, 6, 7, 8-bit with parity bit, or 5, 7, 8, 9-bit without parity bit) . Built-in baud rate generator provides selection of 14 baud rate settings. External clock output, 2-channel 8-bit PWM timer output also available for baud rate settings. External interrupt 1 Single-clock system : 4 channels independent, dual-clock system : 3 channels independent. Selection of rising, falling, or both edge detection. Can be used for recovery from standby mode (edge detection also available in stop mode) External interrupt 2 Except MB89F538/F538L : 8 channels, MB89F538/F538L : 7 channels Can be used for recovery from standby mode. 6-bit PPG, 12-bit PPG Can generate square wave signals with programmable period. 6-bit x 1 channel or 12-bit x 2 channels. 1-channel , compatible with Intel System Administrator bus version 1.0 and Philips I2C specifications. 2-line communications (on MB89PV530/P538/F538/F538L/537AC/538AC) 10-bit resolution x 8 channels. A/D conversion functions (conversion time : 60 tinst*3) A/D converter Supports repeated calls from external clock (except MB89F538/F538L) . Supports repeated calls from internal clock. Standard voltage input provided (AVR) I2C bus interface Standby modes (power saving modes) Sleep mode, stop mode, sub clock mode, watch mode. Process CMOS *1 : Depends on operating frequency. *2 : Using external ROM and MBM27C512. *3 : tinst represents instruction execution time. This can be selected as 1/4, 1/8, 1/16, 1/64 of the main clock cycle or 1/2 of the sub clock cycle. Note : MB89535A/537A/538A have no built-in I2C functions. To use I2C functions, choose the MB89PV530/MB89P538/F538/F538L/537AC/538AC. 4 DS07-12547-7E MB89530A Series MODEL DIFFERENCES AND SELECTION CONSIDERATIONS Part number MB89535A Package MB89537A/ MB89538A/ MB89F538 MB89F538L MB89P538 MB89PV530 537AC 538AC DIP-64P-M01 FPT-64P-M24 FPT-64P-M06 FPT-64P-M23 LCC-64P-M19 MDP-64C-P02 MQP-64C-P01 : Model-package combination available : Model-package combination not available Conversion sockets for pin pitch conversion can be used. DS07-12547-7E 5 MB89530A Series DIFFERENCES AMONG PRODUCTS 1. Memory Capacity When this product is used in an evaluation product or other evaluation configuration, it is necessary to carefully confirm the differences between the model being used and the product it is evaluating. Particular attention should be given to the following (Refer to " CPU CORE 1.Memory Space") . * The program ROM area starts from address 4000H on the MB89F538, MB89F538L, MB89P538 and MB89PV530 models. * Note upper limits on RAM, such as stack areas, etc. 2. Current Consumption * On the MB89PV530, the additional current consumed by the EPROM is added at the connecting socket on the back side. * When operating at low speed, the current consumption in the one-time PROM or EPROM models is greater than on the MASK ROM models. However, current consumption in sleep or stop modes is identical. For details, refer to " ELECTRICAL CHARACTERISTICS". 3. Mask Options The options available for use, and the method of specifying options, differ according to the model. Before use, check the " MASK OPTIONS" specification section. 4. Wild Register Functions The following table shows areas in which wild register functions can be used. Wild Register Usage Areas Part number Address space MB89PV530 4000H to FFFFH MB89P538 4000H to FFFFH MB89F538/F538L 4000H to FFFFH MB89537A/537AC 8000H to FFFFH MB89538A/538AC 4000H to FFFFH MB89535A C000H to FFFFH 6 DS07-12547-7E MB89530A Series PIN ASSIGNMENTS (TOP VIEW) P36/WTO P37/PTO1 P40/INT20/EC P41/INT21/SCK2 P42/INT22/SO2/SDA P43/INT23/SI2/SCL P44/INT24/UCK2 P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST/MOD2*1 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 P63/INT13/X0A*2 P64/X1A*2 RST MOD0 MOD1 X0 X1 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 *4 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 O1 O2 O3 VSS 65 66 67 68 69 70 71 72 73 74 75 76 77 78 92 91 90 89 88 87 86 85 84 83 82 81 80 79 VCC A14 A13 A8 A9 A11 OE A10 CE O8 O7 O6 O5 O4 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1 (UO1) P31/SCK1 (UCK1) /LMCO P30/PPG03/MCO C/N.C. *3 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P20/PWCK P21/PPG01 P22/PPG02 P23 P24 P25 P26 P27 (DIP-64P-M01) (MDP-64C-P02) *1 : Pin 10 is MOD2 pin for MB89F538/F538L and P47/INT27/ADST pins except for MB89F538/F538L. *2 : Pin 25 and pin 26 are P63/INT13, P64 pins for single-clock system and X0A, X1A pins for dual-clock system. *3 : The function of pin 57 depends on the model. For details, refer to "PIN DESCRIPTIONS" and "HANDLING DEVICES". *4 : Package top pin assignments (MB89PV530 only) Pin no. Pin name Pin no. Pin name Pin no. Pin name Pin no. Pin name 65 A15 73 A1 81 O6 89 A8 66 A12 74 A0 82 O7 90 A13 67 A7 75 O1 83 O8 91 A14 68 A6 76 O2 84 CE 92 VCC 69 A5 77 O3 85 A10 70 A4 78 VSS 86 OE 71 A3 79 O4 87 A11 72 A2 80 O5 88 A9 N.C. : Internal connection only. Not for use. (Continued) DS07-12547-7E 7 MB89530A Series 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P45/INT25/UO2 P44/INT24/UCK2 P43/INT23/SI2/SCL P42/INT22/SO2/SDA P41/INT21/SCK2 P40/INT20/EC P37/PTO1 P36/WTO VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1 (UO1) P31/SCK1 (UCK1) /LMCO P30/PPG03/MCO C/N.C.*3 (TOP VIEW) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P63/INT13/X0A*2 P64/X1A*2 RST MOD0 MOD1 X0 X1 VSS P27 P26 P25 P24 P23 P22/PPG02 P21/PPG01 P20/PWCK 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P46/INT26/UI2 P47/INT27/ADST/MOD2*1 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 (FPT-64P-M24) (FPT-64P-M23) *1 : Pin 2 is MOD2 pin for MB89F538/F538L and P47/INT27/ADST pins except for MB89F538/F538L. *2 : Pin 17 and pin 18 are P63/INT13, P64 pins for single-clock system and X0A, X1A pins for dual-clock system. *3 : The function of pin 49 depends on the model. For details, refer to "PIN DESCRIPTIONS" and "HANDLING DEVICES". (Continued) 8 DS07-12547-7E MB89530A Series 64 63 62 61 60 59 58 57 56 55 54 53 52 P44/INT24/UCK2 P43/INT23/SI2/SCL P42/INT22/SO2/SDA P41/INT21/SCK2 P40/INT20/EC P37/PTO1 P36/WTO VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1/ (UO1) P31/SCK1 (UCK1) /LMCO (TOP VIEW) 84 83 82 81 80 79 78 *4 85 86 87 88 89 90 91 92 93 77 76 75 74 73 72 71 70 69 94 95 96 65 66 67 68 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P30/PPG03/MCO C/N.C.*3 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P20/PWCK RST MOD0 MOD1 X0 X1 VSS P27 P26 P25 P24 P23 P22/PPG02 P21/PPG01 20 21 22 23 24 25 26 27 28 29 30 31 32 P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST/MOD2*1 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 P63/INT13/X0A*2 P64/X1A*2 (FPT-64P-M06) (MQP-64C-P01) *1 : Pin 3 is MOD2 pin for MB89F538/F538L and P47/INT27/ADST pins except for MB89F538/F538L. *2 : Pin 18 and pin 19 are P63/INT13, P64 pins for single-clock system and X0A, X1A pins for dual-clock system. *3 : The function of pin 50 depends on the model. For details, refer to "PIN DESCRIPTIONS" and "HANDLING DEVICES". *4 : Package top pin assignments (MB89PV530 only) Pin no. Pin name Pin no. Pin name Pin no. Pin name Pin no. Pin name 65 N.C. 73 A2 81 N.C. 89 OE 66 A15 74 A1 82 O4 90 N.C. 67 A12 75 A0 83 O5 91 A11 68 A7 76 N.C. 84 O6 92 A9 69 A6 77 O1 85 O7 93 A8 70 A5 78 O2 86 O8 94 A13 71 A4 79 O3 87 CE 95 A14 72 A3 80 VSS 88 A10 96 VCC N.C. : Internal connection only. Not for use. (Continued) DS07-12547-7E 9 MB89530A Series (Continued) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 P00 P01 P02 P03 P04 P05 P06 P07 P10 P11 P12 P13 P14 P15 P16 P17 P63/INT13/X0A2 P64/X1A2 RST MOD0 MOD1 X0 X1 VSS P27 P26 P25 P24 P23 P22/PPG02 P21/PPG01 P20/PWCK 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P46/INT26/UI2 P47/INT27/ADST/MOD21 P50/AN0 P51/AN1 P52/AN2 P53/AN3 P54/AN4 P55/AN5 P56/AN6 P57/AN7 AVCC AVR AVSS P60/INT10 P61/INT11 P62/INT12 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P45/INT25/UO2 P44/INT24/UCK2 P43/INT23/SI2/SCL P42/INT22/SO2/SDA P41/INT21/SCK2 P40/INT20/EC P37/PTO1 P36/WTO VCC P35/PWC P34/PTO2 P33/SI1 (UI1) P32/SO1 (UO1) P31/SCK1 (UCK1) /LMCO P30/PPG03/MCO C/NC3 (TOP VIEW) (LCC-64P-M19) *1 : Pin 2 is MOD2 pin for MB89F538/F538L and P47/INT27/ADST pins except for MB89F538/F538L. *2 : Pin 17 and 18 are P63/INT13, P64 pins for single-clock system and X0A, X1A pins for dual-clock system. *3 : The function of pin 49 depends on the model. For details, refer to "PIN DESCRIPTIONS" and "HANDLING DEVICES". 10 DS07-12547-7E MB89530A Series PIN DESCRIPTIONS Pin no. SH-DIP* MDIP*2 1 30 QFP*3 MQFP*4 LQFP*5 BCC*6 Pin name 23 22 X0 31 24 23 X1 28 21 20 MOD0 29 22 21 MOD1 I/O circuit type*7 Function A Connecting pins to crystal oscillator circuit or other oscillator circuit. The X0 pin can connect to an external clock. In that case, X1 is left open. B Input pins for memory access mode setting. Connect directly to Vss. 27 20 19 RST C Reset I/O pin. This pin has pull-up resistance with CMOS I/O or hysteresis input. At an internal reset request, an 'L' signal is output. An 'L' level input initializes the internal circuits. 56 to 49 49 to 42 48 to 41 P00 to P07 D General purpose I/O ports. 48 to 41 41 to 34 40 to 33 P10 to P17 D General purpose I/O ports. 40 33 32 P20/PWCK E General purpose I/O port.Resource I/O pin (hysteresis input).Hysteresis input. This pin also functions as a PWC input. 39 32 31 P21/ PPG01 D General purpose I/O port.This pin also functions as the PPG01 output. 38 31 30 P22/ PPG02 D General purpose I/O port.This pin also functions as the PPG02 output. 37 30 29 P23 D General purpose I/O port. 36 29 28 P24 D General purpose I/O port. 35 28 27 P25 D General purpose I/O port. 34 27 26 P26 D General purpose I/O port. 33 26 25 P27 D General purpose I/O port. 58 51 50 P30/ PPG03/ MCO D General purpose I/O port.This pin also functions as the PPG03 output. 59 52 51 P31/SCK1 (UCK1) / LMCO E General purpose I/O port.Resource I/O pin (hysteresis input).This pin also functions as the UART/SIO clock input/output pin. 60 53 52 P32/SO1 (UO1) D General purpose I/O port.This pin also functions as the UART/SIO data output pin. 61 54 53 P33/SI1 (UI1) E General purpose I/O port.Resource input/output pin (hysteresis input).This pin also functions as the UART/ SIO serial data input pin. 62 55 54 P34/PTO2 D General purpose I/O port.This pin also functions as the PWM timer 2 output pin. 63 56 55 P35/PWC E General purpose I/O port.Resource I/O pin (hysteresis input).This pin also functions as a PWC input. (Continued) DS07-12547-7E 11 MB89530A Series Pin no. SH-DIP* MDIP*2 1 3 5 Pin name I/O circuit type*7 Function QFP* MQFP*4 LQFP* BCC*6 1 58 57 P36/ WTO D General purpose I/O port.Resource output. This pin also functions as the PWC output pin. 2 59 58 P37/ PTO1 D General purpose I/O port.Resource output. This pin also functions as the PWM timer 1 output pin. 3 60 59 P40/ INT20/ EC E General purpose I/O port.Resource I/O pin (hysteresis input).This pin also functions as an external interrupt input or 16-bit timer/counter input. 4 61 60 P41/ INT21/ SCK2 E General purpose I/O port.Resource I/O pin (hysteresis input).This pin also functions as an external interrupt input or SIO clock I/O pin. 61 P42/ INT22/ SO2/ SDA G N-ch open drain output. Resource I/O pin (hysteresis only for INT22 input) . This pin also functions as an external interrupt input, SIO serial data output, or I2C data line. 62 P43/ INT23/ SI2/SCL G N-ch open drain output. Resource I/O pin (hysteresis only for INT23 input) . This pin also functions as an external interrupt, SIO serial data input, or I2C clock I/O pin. 63 P44/ INT24/ UCK2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART clock I/O pin. 64 P45/ INT25/ UO2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART data output pin. 1 P46/ INT26/ UI2 E General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or UART data input pin. 5 6 7 8 9 10 11 to 18 62 63 64 1 2 3 4 to 11 P47/ INT27/ ADST E MOD2 B P50/AN0 to P57/ AN7 H 2 3 to 10 Except MB89F538/F538L General purpose I/O port. Resource I/O pin (hysteresis input) . This pin also functions as an external interrupt input or A/D converter clock input pin. MB89F538/F538L Input pins for memory access mode setting. Connect directly to Vss. N-ch open drain output port. This pin also functions as an A/D converter analog input pin. (Continued) 12 DS07-12547-7E MB89530A Series (Continued) Pin no. SH-DIP* MDIP*2 1 22 to 24 25 QFP* MQFP*4 5 LQFP* BCC*6 Pin name I/O circuit type*7 Function 15 to 17 14 to 16 P60/INT10 to P62/INT12 I General purpose input port. Resource input pin (hysteresis input) . This pin also functions as an external interrupt input pin. 3 18 17 P63/INT13 I Single-clock system General purpose input port. Resource input (hysteresis input) . This pin also functions as an external interrupt. X0A A Dual-clock system Connected pin for sub clock. P64 J Single-clock system General purpose input port. X1A A Dual-clock system Connected pin for sub clock. 26 19 18 64 57 56 VCC Power supply pin. 32 25 24 VSS Ground pin (GND) . 19 12 11 AVCC A/D converter power supply pin. 20 13 12 AVR A/D converter reference voltage input pin. 21 14 13 AVSS A/D converter power supply pin. Used at the same voltage level as the Vss supply. 57 50 49 C MB89F538 Capacitor connection pin for stabilization power supply. Connect an external ceramic capacitor of approximately 0.1 F. MB89P538 If "Available" is selected for the step-down circuit stabilization time, VCC is fixed. If "Unavailable" is selected for the step-down circuit stabilization time, VSS is fixed. MB89PV530 MB89537A/537AC MB89538A/538AC MB89535A MB89F538L N.C. pin *1 : DIP-64P-M01 *2 : MDP-64C-P02 *3 : FPT-64P-M06 *4 : MQP-64C-P01 *5 : FPT-64P-M24/M23 *6 : LCC-64P-M19 *7 : For I/O circuit type, refer to " I/O CIRCUIT TYPE" . DS07-12547-7E 13 MB89530A Series External EPROM Socket Pin Function Descriptions (MB89PV530 only) Pin no. I/O Circuit Pin name 1 2 type*3 MQFP* MDIP* Function 65 66 67 68 69 70 71 72 73 74 66 67 68 69 70 71 72 73 74 75 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 O Address output pins. 75 76 77 77 78 79 O1 O2 O3 I Data input pins 78 80 VSS O Power supply pin (GND) . 79 80 81 82 83 82 83 84 85 86 O4 O5 O6 O7 O8 I Data input pins. 84 87 CE O ROM chip enable pin. Outputs an "H" level signal in standby mode. 85 88 A10 O Address output pin. 86 89 OE O ROM output enable pin. Outputs "L" at all times. 87 88 89 91 92 93 A11 A9 A8 O 90 94 A13 O 91 95 A14 O 92 96 VCC O EPROM power supply pin. 65 76 81 90 N.C. O Internally connected. These pins always left open. Address output pins. *1 : MDP-64C-P02 *2 : MQP-64C-P01 *3 : For I/O circuit type, refer to " I/O CIRCUIT TYPE" . 14 DS07-12547-7E MB89530A Series I/O CIRCUIT TYPES Type Circuit X1 (X1A) N-ch A Remarks Clock input P-ch Oscillator feedback resistance * High speed side = approx. 1 M * Low speed side = approx. 10 M P-ch X0 (X0A) N-ch Standby control Mode input B R * Hysteresis input * Pull-down resistance built-in to MB89535A MB89537A/537AC MB89538A/538AC * Pull-up resistance approx. 50 k * Hysteresis input R P-ch Reset output C N-ch Reset input R Pull-up control resistor P-ch P-ch D N-ch * CMOS I/O * Software pull-up resistance can be used. Approx. 50 k Digital output Digital output Port input R Pull-up control resistors P-ch P-ch * CMOS I/O * Software pull-up resistance can be used. Approx. 50 k Digital output E N-ch Digital output Port input Resource input (Continued) DS07-12547-7E 15 MB89530A Series (Continued) Type Circuit N-ch G Remarks Digital output * N-ch open drain output * Hysteresis input * CMOS input Resource input Port input * N-ch open drain output * Analog input (A/D converter) P-ch H N-ch Digital output Analog input R P-ch Pull-up control resistors I * Hysteresis input * CMOS input * Software pull-up resistance can be used. Approx. 50 k Resource Port R P-ch Pull-up control resistors * CMOS input * Software pull-up resistance can be used. Approx. 50 k J Port 16 DS07-12547-7E MB89530A Series HANDLING DEVICES 1. Preventing Latch-up Care must be taken to ensure that maximum voltage ratings are not exceeded (to prevent latch-up) . When CMOS integrated circuit devices are subjected to applied voltages higher than Vcc at input and output pins (other than medium- and high-withstand voltage pins), or to voltages lower than Vss, as well as when voltages in excess of rated levels are applied between Vcc and Vss, the phenomenon known as latch-up can occur. When a latch-up condition occurs, supply current can increase dramatically and may destroy semiconductor elements. In using semiconductor devices, always take sufficient care to avoid exceeding maximum ratings. Also when switching power on or off to analog systems, care must be taken that analog power supplies (AVCC, AVR) and analog input signals do not exceed the level of the digital power supply. 2. Power Supply Voltage Fluctuations Even within the warranted operating range of the Vcc supply voltage, sudden changes in supply voltage can cause abnormal operation. As a measure for stability, it is recommended that the Vcc ripple fluctuation (peak to peak value) should be kept within 10% of the reference Vcc value on commercial power supply (50 Hz/60 Hz), and instantaneous voltage fluctuations such as at power-on and shutdown should be kept within a transient variability limit of 0.1V/ms. 3. Treatment of Unused Input Pins If unused input pins are left open, abnormal operation may result. Any unused input pins should be connected to pull-up or pull-down resistance. 4. Treatment of N.C. Pins Any pins marked 'NC' (not connected) must be left open. 5. Treatment of Power Supply Pins on Models with Built-in A/D Converter Even when A/D converters are not in use, pins should be connected so that AVCC = VCC, and AVSS = AVR = VSS. 6. Precautions for Use of External Clock Even when an external clock signal is used, an oscillator stabilization wait period is used after a power-on reset, or escape from sub clock mode or stop mode. 7. Execution of Programs on RAM Debugging of programs executed on RAM cannot be performed even when using the MB89PV530. 8. Wild Register Functions Wild registers cannot be debugged with the MB89PV530 and tools. To verify operations, actual in-device testing on the MB89P538 or MB89F538/F538L is advised. DS07-12547-7E 17 MB89530A Series 9. Details on handling the C terminal of the MB89530 series The MB89530 series contains the following products. The regulator integrated model and the regulator-less model have different performance characteristics. Part No. Operation Voltage integrated model Terminal type Terminal treatments MB89PV530 MB89P538 Not included 2.7 V to 5.5 V Included 3.5 V to 5.5 V MB89F538L 2.3 V to 3.6 V MB89537A/537AC 2.2 V to 5.5 V C terminal Included Not included Not required Fixed to VCC Not included MB89F538 MB89538A/538AC N.C. terminal N.C. terminal Fixed to VSS 0.1 F capacitor connected Not required MB89535A Although these product models have the same internal resources, the operation sequence after a power-on reset is different between the regulator integrated model and regulator-less model. The operation sequence after a power-on reset of each model is shown below. Power supply (VCC) Voltage step-down circuit stabilization time + oscillation stabilization time (219/FCH) + (218/FCH) CPU operation of regulator integrated model (MB89F538 only) Oscillation stabilization time (218/FCH) CPU operation of regulator-less model (exclude MB89F538) CPU started on regulator-less model (Reset vector) CPU started on regulator integrated model (Reset vector) FCH : Crystal oscillator frequency As above, the regulator integrated model starts the CPU behind the regulator-less model. This is because the regulator requires a settling time for normal operation. The MB89P538 offers a choice of regulator-integrated and regulator-less models selectable depending on the C-terminal treatment. Use the right one for your mask board. 10. Note to Noise in the External Reset Pin (RST) If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunctions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST). 18 DS07-12547-7E MB89530A Series PROGRAMMING AND ERASING FLASH MEMORY ON THE MB89F538/F538L 1. Flash Memory The flash memory is located between 4000H and FFFFH in the CPU memory map and incorporates a flash memory interface circuit that allows read access and program access from the CPU to be performed in the same way as MASK ROM. Programming and erasing flash memory is also performed via the flash memory interface circuit by executing instructions in the CPU. This enables the flash memory to be updated in place under the control of the CPU, providing an efficient method of updating program and data. 2. Flash Memory Features * * * * * * * * 48 Kbytes x 8-bit configuration (16 Kbytes + 8 Kbytes + 8 Kbytes + 16 Kbytes sectors) Automatic programming algorithm (Embedded algorithm : Equivalent to MBM29LV200) Includes an erase pause and restart function Data polling and toggle bit for detection of program/erase completion Detection of program/erase completion via CPU interrupt Compatible with JEDEC-standard commands Sector Protection (sectors can be combined in any combination) No. of program/erase cycles : 10,000 (Min) 3. Procedure for Programming and Erasing Flash Memory Programming and reading flash memory cannot be performed at the same time. Accordingly, to program or erase flash memory, the program must first be copied from flash memory to RAM so that programming can be performed without program access from flash memory. 4. Flash Memory Register * Flash memory control status register (FMCS) Address bit7 007AH bit6 bit5 bit4 INTE RDYINT WE RDY R/W R/W R R/W bit3 bit2 Reserved Reserved R/W R/W bit0 Initial value Reserved 000X00-0B R/W bit1 5. Sector Configuration The table below shows the sector configuration of flash memory and lists the addresses of each sector for both during CPU access a flash memory programming. * Sector configuration of flash memory Flash Memory CPU Address Programmer Address* 16 Kbytes FFFFH to C000H 1FFFFH to 1C000H 8 Kbytes BFFFH to A000H 1BFFFH to 1A000H 8 Kbytes 9FFFH to 8000H 19FFFH to 18000H 16 Kbytes 7FFFH to 4000H 17FFFH to 14000H * : Programmer address The programmer address is the address to be used instead of the CPU address when programming data from a parallel flash memory programmer. Use the programmer address on programming or erasing using a generalpurpose parallel programmer. DS07-12547-7E 19 MB89530A Series ONE-TIME WRITING SPECIFICATIONS WITH PROM AND EPROM MICROCONTROLLERS The MB89P538 has a PROM mode with functions equivalent to the MBM27C1001, allowing writing with a general purpose ROM writer using a proprietary adapter. Note, however, that the use of electronic signature mode is not supported. * Memory map for EPROM mode The following illustration shows a memory map for EPROM mode. There are no PROM options. Normal operating mode 0000H EPROM mode (corresponding addresses on EPROM writer) 0000H I/O 0080H RAM 0100H 0200H 0880H General purpose register Prohibited Prohibited 4000H 4000H Program (EPROM) ROM FFFFH FFFFH Prohibited 1FFFFH 20 DS07-12547-7E MB89530A Series * Recommended screening conditions Before one-time writing of microcontroller programs to PROM, high temperature aging is recommended as a screening process for chips before they are mounted. Program, verify High temperature aging +150 C, 48h Read Mount * About writing yields The nature of chips before one-time writing of microcontroller programs to PROM prevents the use of all-bit writing tests. Therefore it is not possible to guarantee writing yields of 100% in some cases. DS07-12547-7E 21 MB89530A Series EPROM WRITING TO PIGGY-BACK/EVALUATION CHIPS This section describes methods of writing to EPROM on piggy-back/evaluation chips. * EPROM model MBM27C512-20TV * Memory Space Normal operating mode 0000H (Corresponding address on ROM writer) 0000H I/O 0080H Prohibited RAM 0880H Prohibited 4000H 4000H PROM 48 Kbytes FFFFH EPROM FFFFH * Writing to EPROM 1) Set up the EPROM writer for the MBM27C512. 2) Load program data to the ERPOM writer, in the area 4000H to FFFFH. 3) Use the EPROM writer to write to the area 4000H to FFFFH. 22 DS07-12547-7E MB89530A Series Low voltage oscillator circuit (32.786 kHz) P63/INT13/X0A*1 P64/X1A*1 CMOS I/O port Port 0 Sub clock 8 Port 1 BLOCK DIAGRAM 8 P00 to P07 Port 6 Clock control 4 CMOS I/O port 6-bit PPF03 P31/SCK1 (UCK1) /LMCO 8-bit PWM timer 2 P33/SI1 (UI1) Port 3 P30/PPG03/MCO 8-bit PWM timer 1 P34/PTO2 UART/SIO P35/PWC P21/PPG01 P22/PPG02 P23 to P27 CMOS I/O port P40/INT20/EC SIO P41/INT21/SCK2 UART N-ch I/O P42/INT22/ SO2/SDA I2C P43/INT23/ SI2/SCL 16-bit timer/ counter 1 P44/INT24/UCK2 External interrupt 2 (level) P45/INT25/UO2 P46/INT26/UI2 P47/INT27/ADST*2 CMOS I/O port PWC P36/WTO P37/PTO1 P20/PWCK Port 4 21-bit time base timer Internal data bus Reset circuit (watchdog timer) RST P32/SO1 (UO1) 12-bit PPG02 Oscillator circuit Clock controller Port 2 12-bit PPG01 CMOS I/O port Main clock X0 X1 P10 to P17 External interrupt 1 (edge) N-ch output CMOS I/O port RAM (512 Kbytes/1 Kbyte/2 Kbytes) F2MC-8L CPU 8 10-bit A/D converter Port 5 P60/INT10 to P62/INT12 Watch prescaler 8 P50/AN0 to P57/AN7 AVCC AVR AVSS Wild register ROM (16 Kbytes/32 Kbytes/48 Kbytes) Other pins MOD0, MOD1, MOD2*2, VCC, VSS, C/N.C. *1 : P63/INT13, P64 pins for single-clock system and X0A, X1A pins dual-clock system *2 : MOD2 pin for MB89F538/F538L and P47/INT27/ADST pin except for MB89F538/F538L. DS07-12547-7E 23 MB89530A Series CPU CORE 1. Memory Space The MB89530A series has 64 Kbytes of memory space, containing all I/O, data areas, and program areas. The I/O area is located at the lowest addresses, with the data area placed immediately above. The data area can be partitioned into register areas, stack areas, or direct access areas depending on the application. The program area is located at the opposite end of memory, closest to the highest addresses, and the highest part of this area is assigned to the tables of interrupt and reset vectors and vector call instructions. The following diagram shows the structure of memory space in the MB89530A series. * Memory Map MB89535A 0000H MB89537A/537AC 0000H 0200H General purpose register I/O 0080H 0080H RAM 0100H 0000H I/O I/O 0080H MB89PV530 MB89P538/F538/F538L MB89538A/538AC RAM 0100H 0200H General purpose register RAM 0100H 0200H General purpose register 0280H 0480H Open 0C80H 0C91H Open 0C80H Wild register 0C91H 0880H Wild register 0C91H Wild register Open Open Open Open 0C80H 4000H 8000H ROM C000H ROM ROM FFC0H FFFFH FFC0H Vector tables*2 External ROM*1 FFFFH FFC0H Vector tables*2 FFFFH Vector tables*2 *1 : The external ROM area is on the MB89PV530 only. *2 : Vector tables (reset, interrupt, vector call instructions) 24 DS07-12547-7E MB89530A Series 2. Registers The F2MC-8L series has two types of registers, dedicated-use registers within the CPU, and general-purpose registers in memory. Program counter (PC) : 16-bit length, shows the location where instructions are stored. Accumulator (A) : 16-bit length, a temporary memory register for calculation operations. The lower byte is used for 8-bit data processing instructions. Temporary accumulator (T) : 16-bit length, performs calculations with the accumulator. The lower byte is used for 8-bit data processing instructions. Index register (IX) : 16-bit length, a register for index modification. Extra pointer (EP) : 16-bit length, a pointer indicating memory addresses. Stack pointer (SP) : 16-bit length, indicates stack areas. Program status (PS) : 16-bit length, contains register pointer and condition code. 16 bits Initial value FFFDH : Program counter PC A : Accumulator Not fixed T : Temporary accumulator Not fixed IX : Index register Not fixed EP : Extra pointer Not fixed SP : Stack pointer Not fixed PS : Program status I-flag = 0, IL1, 0 = 11 Other bits not fixed In addition, the PS register can be divided so that the upper 8 bits are used as a register bank pointer (RP), and the lower 8 bits as a condition code register (CCR). (Refer to the following illustration.) * Program status register configuration 15 PS 14 13 12 10 9 8 Open Open Open RP RP DS07-12547-7E 11 7 6 5 4 3 2 1 0 H I IL1 IL0 N Z V C CCR 25 MB89530A Series The RP register shows the address of the register bank currently being used, so that the RP value and the actual address are related by the conversion rule shown in the following illustration. * General purpose register area real address conversion principle Operation code lower RP upper "0" Address generated "0" "0" "0" "0" "0" "0" "1" R4 R3 R2 R1 R0 b2 b1 b0 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 The CCR register has bits that show the content of results of calculations and transferred data, and bits that control CPU operation during interrupts. H-flag I-flag IL1, 0 N-flag Z-flag V-flag C-flag : Set to "1" if calculations result in carry or borrow operations from bit 3 to bit 4, otherwise set to "0". This flag is used for decimal correction instructions. : This flag is set to "1" if interrupts are enabled, and "0" if interrupts are prohibited. The default value at reset is "0". : Indicates the level of the currently permitted interrupts. Only interrupt requests having a more powerful level than the value of these bits will be processed. : : : : IL1 IL0 Interrupt level 0 0 0 1 1 0 2 1 1 3 1 Strength Strong Weak Set to "1" if the highest bit is "1" after a calculation, otherwise cleared to "0". Set to "1" if a calculation result is "0", otherwise cleared to "0". Set to "1" if a two's complement overflow results during a calculation, otherwise cleared to "0". Set to "1" if a calculation results in a carry or borrow operation from bit 7, otherwise cleared to "0". This is also the shift-out value in a shift instruction. In addition, the following general purpose registers are available. General purpose registers: 8 bits length, used to contain data. The general purpose registers are 8-bit registers located in memory. There are eight such registers per bank, and the MB89530A series have up to 32 banks for use. The bank currently in use is indicated by the register bank pointer (RP). 26 DS07-12547-7E MB89530A Series *Register bank configuration Address at this location = 0100H + 8 x (RP) R0 R1 R2 R3 R4 R5 R6 R7 32 banks Memory area DS07-12547-7E 27 MB89530A Series I/O MAP Address Register name 00H PDR0 Port 0 data register 01H DDR0 Port 0 direction register 02H PDR1 Port 1 data register 03H DDR1 Port 1 direction register Register description 04H to 06H Write/Read Initial value R/W XXXXXXXXB W 0 0 0 0 0 0 0 0B R/W XXXXXXXXB W 0 0 0 0 0 0 0 0B (Reserved area) 07H SYCC System clock control register R/W X -1 MM1 0 0B 08H STBC Standby control register R/W 0 0 0 1 0 - - -B 09H WDTC Watchdog control register R/W 0 - - - XXXXB 0AH TBTC Time base timer control register R/W 0 0 - - - 0 0 0B 0BH WPCR Watch prescaler control register R/W 0 0 - - 0 0 0 0B 0CH PDR2 Port 2 data register R/W XXXXXXXXB 0DH DDR2 Port 2 direction register R/W 0 0 0 0 0 0 0 0B 0EH PDR3 Port 3 data register R/W XXXXXXXXB 0FH DDR3 Port 3 direction register R/W 0 0 0 0 0 0 0 0B 10H PDR4 Port 4 data register R/W XXXX 1 1 XXB 11H DDR4 Port 4 direction register R/W 0 0 0 0 - - 0 0B 12H PDR5 Port 5 data register R/W 11111111B 13H PDR6 Port 6 data register R XXXXXXXXB 14H to 21H (Reserved area) 22H SMC11 Serial mode control register 1 (UART) R/W 0 0 0 0 0 0 0 0B 23H SRC1 Serial rate control register (UART) R/W - - 0 1 1 0 0 0B 24H SSD1 Serial status and data register (UART) R/W 0 0 1 0 0 - 1XB 25H SIDR1/ SODR1 Serial input/output data register (UART) R/W XXXXXXXXB 26H SMC12 Serial mode control register 2 (UART) R/W - - 1 0 0 0 0 1B 27H CNTR1 PWM control register 1 R/W 0 0 0 0 0 0 0 0B 28H CNTR2 PWM control register 2 R/W 0 0 0 - 0 0 0 0B 29H CNTR3 PWM control register 3 R/W - 0 0 0 - - - -B 2AH COMR1 PWM compare register 1 W XXXXXXXXB 2BH COMR2 PWM compare register 2 W XXXXXXXXB 2CH PCR1 PWC pulse width control register 1 R/W 0 0 0 - - 0 0 0B 2DH PCR2 PWC pulse width control register 2 R/W 0 0 0 0 0 0 0 0B 2EH RLBR PWC reload buffer register R/W XXXXXXXXB 2FH SMC21 Serial mode control register 1 (UART/SIO) R/W 0 0 0 0 0 0 0 0B 30H SMC22 R/W 0 0 0 0 0 0 0 0B 31H SSD2 Serial mode control register 2 (UART/SIO) Serial status and data register (UART/SIO) R/W 0 0 0 0 1 - - -B 32H SIDR2/ SODR2 Serial data register (UART/SIO) R/W XXXXXXXXB 33H SRC2 Baud rate generator reload register R/W XXXXXXXXB (Continued) 28 DS07-12547-7E MB89530A Series Address 34H 35H 36H 37H 38H 39H 3AH 3BH 3CH 3DH 3EH 3FH 40H 41H to 48H 49H 4AH, 4BH 4CH 4DH 4EH 4FH 50H 51H 52H 53H 54H 55H 56H 57H 58H 59H 5AH 5BH to 6FH 70H 71H 72H 73H 74H 75H 76H 77H Register name ADC1 ADC2 ADDL ADDH PPGC2 PRL22 PRL21 PRL23 TMCR TCHR TCLR EIC1 EIC2 DDCR PPGC1 PRL12 PRL11 PRL13 IACR IBSR IBCR ICCR IADR IDAR EIE2 EIF2 RCR1 RCR2 CKR SMR SDR PURR0 PURR1 PURR2 PURR3 PURR4 WREN Register description A/D control register 1 A/D control register 2 A/D data register low A/D data register high PPG2 control register (12-bit PPG) PPG2 reload register 2 (12-bit PPG) PPG2 reload register 1 (12-bit PPG) PPG2 reload register 3 (12-bit PPG) 16-bit timer control register 16-bit timer counter register high 16-bit timer counter register low External interrupt 1 control register 1 External interrupt 1 control register 2 (Reserved area) DDC select register (Reserved area) PPG1 control register (12-bit PPG) PPG1 reload register 2 (12-bit PPG) PPG1 reload register 1 (12-bit PPG) PPG1 reload register 3 (12-bit PPG) I2C address control register I2C bus status register I2C bus control register I2C clock control register I2C address register I2C data register External interrupt 2 control register External interrupt 2 flag register 6-bit PPG control register 1 6-bit PPG control register 2 Clock output control register (Reserved area) Serial mode register (SIO) Serial data register (SIO) Port 0 pull-up resistance register Port 1 pull-up resistance register Port 2 pull-up resistance register Port 3 pull-up resistance register Port 4 pull-up resistance register Wild register enable register Write/Read Initial value R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 - 0B - 0 0 0 0 0 0 1B XXXXXXXXB - - - - - - 0 0B 0 0 0 0 0 0 0 0B 0X0 0 0 0 0 0B XX0 0 0 0 0 0B XX0 0 0 0 0 0B - - 0 0 0 0 0 0B 0 0 0 0 0 0 0 0B 0 0 0 0 0 0 0 0B 0 0 0 0 0 0 0 0B 0 0 0 0 0 0 0 0B R/W - - - - - - - 0B R/W R/W R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0B 0X0 0 0 0 0 0B XX0 0 0 0 0 0B XX0 0 0 0 0 0B - - - - - 0 0 0B 0 0 0 0 0 0 0 0B 0 0 0 0 0 0 0 0B 0 0 0 XXXXXB - XXXXXXXB XXXXXXXXB 0 0 0 0 0 0 0 0B - - - - - - - 0B 0 0 0 0 0 0 0 0B 0X0 0 0 0 0 0B - - - - - - 0 0B R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0B XXXXXXXXB 11111111B 11111111B 11111111B 11111111B 1 1 1 1 - -1 1 B - - 0 0 0 0 0 0B (Continued) DS07-12547-7E 29 MB89530A Series (Continued) Address Register name 78H WROR 79H Register description Write/Read Initial value Wild register data test register R/W - - 0 0 0 0 0 0B PURR6 Port 6 pull-up resistance register R/W ---11111B 7AH FMCS Flash memory control status resister R/W 0 0 0X0 0 - 0B 7BH ILR1 Interrupt level setting register 1 W 1 1 1 1 1 1 1 1B 7CH ILR2 Interrupt level setting register 2 W 1 1 1 1 1 1 1 1B 7DH ILR3 Interrupt level setting register 3 W 1 1 1 1 1 1 1 1B 7EH ILR4 Interrupt level setting register 4 7FH ITR Interrupt test register C80H WRARH1 C81H WRARL1 W 1 1 1 1 1 1 1 1B Access prohibited XXXXXX0 0B Upper address setting register 1 R/W XXXXXXXXB Lower address setting register 1 R/W XXXXXXXXB C82H WRDR1 Data setting register 1 R/W XXXXXXXXB C83H WRARH2 Upper address setting register 2 R/W XXXXXXXXB C84H WRARL2 Lower address setting register 2 R/W XXXXXXXXB C85H WRDR2 Data setting register 2 R/W XXXXXXXXB C86H WRARH3 Upper address setting register 3 R/W XXXXXXXXB C87H WRARL3 Lower address setting register 3 R/W XXXXXXXXB C88H WRDR3 Data setting register 3 R/W XXXXXXXXB C89H WRARH4 Upper address setting register 4 R/W XXXXXXXXB C8AH WRARL4 Lower address setting register 4 R/W XXXXXXXXB C8BH WRDR4 Data setting register 4 R/W XXXXXXXXB C8CH WRARH5 Upper address setting register 5 R/W XXXXXXXXB C8DH WRARL5 Lower address setting register 5 R/W XXXXXXXXB C8EH WRDR5 Data setting register 5 R/W XXXXXXXXB C8FH WRARH6 Upper address setting register 6 R/W XXXXXXXXB C90H WRARL6 Lower address setting register 6 R/W XXXXXXXXB C91H WRDR6 Data setting register 6 R/W XXXXXXXXB * Description of write/read symbols : R/W : read/write enabled R : Read only W : Write only * Description of initial values : 0 : This bit initialized to "0". 1 : This bit initialized to "1". X : The initial value of this bit is not determined. M : The initial value of this bit is a mask option. - : This bit is not used. Note : Do not use reserved spaces. 30 DS07-12547-7E MB89530A Series ELECTRICAL CHARACTERISTICS 1. Absolute Maximum Ratings Parameter Symbol Rating Unit Remarks Min Max VCC, AVCC VSS - 0.3 VSS + 6.0 V AVR VSS - 0.3 VSS + 6.0 V MB89535A/537A/538A*2 MB89537AC/538AC MB89F538/F538L//P538 MB89PV530 VSS - 0.3 VCC + 0.3 V Other than P42, P43 VSS - 0.3 VSS + 6.0 V P42, P43 VSS - 0.3 VCC + 0.3 V Other than P42, P43 VSS - 0.3 VSS + 6.0 V P42, P43 ICLAMP - 2.0 + 2.0 mA *3 | ICLAMP | 20 mA *3 IOL 15 mA "L" level average output current IOLAV 4 mA "L" level maximum total output current IOL 100 mA "L" level average total output current IOLAV 40 mA "H" level maximum output current IOH -15 mA "H" level average output current IOHAV -4 mA "H" level maximum total output current IOH -50 mA "H" level average total output current IOHAV -20 mA Current consumption PD 300 mW Operating temperature TA -40 +85 C Tstg -55 +150 C Supply voltage*1 Input voltage*1 VI Output voltage*1 VO Maximum clamp current Total maximum clamp current "L" level maximum output current Storage temperature Average value (operating current x operating duty) Average value (operating current x operating duty) Average value (operating current x operating duty) Average value (operating current x operating duty) *1 : The parameter is based on AVss = Vss = 0 V. *2 : AVcc and Vcc are to be used at the same potential. AVR should not exceed AVcc + 0.3 V. (Continued) DS07-12547-7E 31 MB89530A Series (Continued) *3 : * Applicable to pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40, P41, P44 to P47, P60 to P64 * Use within recommended operating conditions. * Use at DC voltage (current) . * The +B signal should always be applied with a limiting resistance placed between the +B signal and the microcontroller. * The value of the limiting resistance should be set so that when the +B signal is applied the input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods. * Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect other devices. * Note that if a +B signal is input when the microcontroller current is off (not fixed at 0 V) , the power supply is provided from the pins, so that incomplete operation may result. * Note that if the +B input is applied during power-on, the power supply is provided from the pins and the resulting supply voltage may not be sufficient to operate the power-on result. * Care must be taken not to leave the +B input pin open. * Note that analog system input/output pins other than the A/D input pins (LCD drive pins, comparator input pins, etc.) cannot accept +B signal input. * Sample recommended circuits : * Input/Output Equivalent circuits Protective diode VCC Limiting resistance P-ch +B input (0 V to 16 V) N-ch R WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. 32 DS07-12547-7E MB89530A Series 2. Recommended Operating Conditions (AVss = Vss = 0 V) Parameter Supply voltage Operating temperature Symbol VCC, AVCC Value Unit Remarks Min Max 2.2* 5.5 V Range warranted for normal operation 1.5 5.5 V RAM status in stop mode 2.7* 5.5 V Range warranted for normal operation 1.5 5.5 V RAM status in stop mode 3.5 5.5 V Range warranted for normal operation 3.0 5.5 V RAM status in stop mode 2.4 3.6 V Range warranted for normal operation RAM status in stop mode 1.5 3.6 V AVR 3.5 AVCC V TA -40 +85 C MB89535A MB89537A/538A MB89537AC/ 538AC MB89P538 MB89PV530 MB89F538 MB89F538L * : Varies according to frequency used, and instruction cycle. Refer to "Operating voltage vs. operating frequency (MB89P538/MB89PV530) ", "Operating voltage vs. operating frequency (MB89535A/537A/538A/537AC/538AC) ", "Operating voltage vs. operating frequency (MB89F538) " and "5. A/D Converter Electrical Characteristics". DS07-12547-7E 33 MB89530A Series * Operating voltage vs. operating frequency (MB89P538/MB89PV530) Range of warranted analog precision : VCC = AVCC = 3.5 V to 5.5 V 5.5 Operating voltage VCC (V) 5.0 4.0 3.5 3.0 2.7 2.2 2.0 1.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.5 Operating frequency (MHz) (at instruction cycle = 4 / FCH) 4.0 2.0 0.8 0.4 0.32 Minimum instruction execution time (Instruction cycles) (s) indicates warranted operation at TA = -10 C to +55 C * Operating voltage vs. operating frequency (MB89535A/537A/538A/537AC/538AC) Range of warranted analog precision : VCC = AVCC = 3.5 V to 5.5 V Operating voltage VCC (V) 5.5 5.0 4.0 3.5 3.0 2.7 2.2 2.0 1.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.5 Operating frequency (MHz) (at instruction cycle = 4 / FCH) 4.0 2.0 0.8 0.4 0.32 Minimum instruction execution time (Instruction cycles) (s) 34 DS07-12547-7E MB89530A Series * Operating voltage vs. operating frequency (MB89F538) Range of warranted analog precision : VCC = AVCC = 3.5 V to 5.5 V Operating voltage VCC (V) 5.5 5.0 4.0 3.5 3.0 2.0 1.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.5 Operating frequency (MHz) 4.0 2.0 0.8 0.4 0.32 Minimum instruction execution time (Instruction cycles) (s) Operating voltage VCC (V) *Operating voltage vs. operating frequency (MB89F538L) Range of warranted analog precision : VCC = AVCC = 2.4 V to 3.6 V 4.0 3.6 3.0 2.4 2.0 1.0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 12.5 Operating frequency (MHz) (at instruction cycle = 4 / FCH) 4.0 2.0 0.8 0.4 0.32 Minimum instruction execution time (Instruction cycles) (s) DS07-12547-7E 35 MB89530A Series WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their representatives beforehand. 36 DS07-12547-7E MB89530A Series 3. DC Characteristics (1) Supply Voltage at 5.0 (V) (except MB89F538L) (AVCC = VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter "H" level input voltage Value Symbol Pin name Condition Min Typ Max VIH P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, SI1, SI2 0.7 VCC VCC + 0.3 V VIHS RST, MOD0, MOD1, INT20 to INT27, UCK1, UI1, INT10 to INT13, SCK1, EC, PWCK, PWC, SCK2, UCK2, UI2, ADST 0.8 VCC VCC + 0.3 V VSS + 1.4 VSS + 5.5 V With SMB input buffer selected*1 0.7 VCC VSS + 5.5 V With I2C input buffer selected*1 VIL P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, SI1, SI2 VSS - 0.3 0.3 VCC V VILS RST, MOD0, MOD1, INT20 to INT27, UCK1, UI1, INT10 to INT13, SCK1, EC, PWCK, PWC, SCK2, UCK2, UI2, ADST VSS - 0.3 0.2 VCC V VSS - 0.3 VSS + 0.6 V With SMB input buffer selected*1 VSS - 0.3 0.3 VCC V With I2C input buffer selected*1 VSS - 0.3 VCC + 0.3 V VSS + 5.5 V 4.0 V 0.4 V VIHSMB Unit SCL, SDA VIHI2C "L" level input voltage VILSMB SCL, SDA VILI2C Open drain output applied voltage "H" level output voltage VD1 P50 to P57 VD2 P42, P43 VOH P00 to P07, P10 to P17, IOH = P20 to P24, P30 to P37, -2.0 mA P40, P41, P44 to P47 P25 to P27 "L" level output voltage VOL Remarks IOH = -3.0 mA P00 to P07, P10 to P17, P20 to P27, P30 to P37, IOL = P40 to P47, P50 to P57, 4.0 mA RST (Continued) DS07-12547-7E 37 MB89530A Series (AVCC = VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Input leak current (Hi-Z output leak current) Open drain output leak current Pull-up resistance Pull-down resistance Pin name Symbol ILI Value Unit Remarks +5 A With no pull-up resistance specified 5 A Min Typ Max P00 to P07, P10 to P17, P20 to P27, P30 to P37, 0.0 V < VI < P40 to P47, P50 to P57, VCC P60 to P64 -5 0.0 V < VI < VSS + 5.5 V ILIOD P42, P43 RUP P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40, P41, P44 to P46, P47*2, P60 to P64, RST RDOWN MOD0, MOD1 25 40 100 k With pull-up resistance specified. The RST signal is excluded. 25 40 100 k Only for mask ROM product. 15 20 mA MB89P538/ PV530 6 10 mA MB89F538 8 13 MB89535A/7A/8A mA MB89537AC/ 538AC 5 8.5 mA 1.5 3 mA MB89F538 1.5 3 MB89535A/7A/8A mA MB89537AC/ 538AC 5 7 Sleep mode mA MB89P538/ PV530 3 5 mA FCH = 10.0 MHz VCC = 5.0 V tinst = 0.4 s ICC1 FCH = 10.0 MHz VCC = 5.0 V tinst = 6.4 s ICC2 Supply current Condition VCC ICCS1 ICCS2 FCH = 10.0 MHz VCC = 5.0 V tinst = 0.4 s FCH = 10.0 MHz VCC = 5.0 V tinst = 6.4 s MB89P538/ PV530 Sleep mode MB89F538 2.5 5 Sleep mode MB89535A/7A/8A mA MB89537AC/ 538AC 1.5 3 Sleep mode mA MB89P538/ PV530 1 2 mA 2 Sleep mode MB89535A/7A/8A mA MB89537AC/ 538AC 1 Sleep mode MB89F538 (Continued) 38 DS07-12547-7E MB89530A Series (Continued) Parameter Pin name Symbol FCL = 32.768 kHz VCC = 5.0 V TA = +25 C ICCL VCC Supply current ICCLS FCL = 32.768 kHz VCC = 5.0 V TA = +25 C 3 7 400 800 Sub mode mA MB89P538/ PV530 A Sub mode MB89F538 50 85 A Sub mode MB89535A/7A/8A MB89537AC/ 538AC 30 50 A Sub, sleep mode MB89P538/ PV530 15 30 A Sub, sleep mode MB89F538 15 30 A Sub, sleep mode MB89535A/7A/8A MB89537AC/ 538AC ICCT FCL = 32.768 kHz VCC = 5.0 V TA = +25 C 5 15 A Watch mode, main stop ICCH TA = +25 C 3 10 A Sub, stop modes FCH = 10.0 MHz 4 6 mA A/D conversion running TA = +25 C 1 5 A A/D stopped f = 1 MHz 5 15 pF IA AVCC IAH Input capacitance (AVCC = VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Value Condition Unit Remarks Min Typ Max CIN Except VCC, VSS, AVCC, AVSS *1 : The MB89PV530/P538/F538/537AC/538AC have a built-in I2C function, and a choice of input buffers by software setting. MB89535A/537A/538A have no built-in I2C functions, and therefore this standard does not apply. *2 : For P47 of MB89F538, pull-up resistor is not mounted as this pin is used as MOD2 pin. DS07-12547-7E 39 MB89530A Series (2) Supply Voltage at 3.0 (V) (except MB89F538) (AVCC = VCC = 3.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter "H" level input voltage Symbol Pin name Condition VIH P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, SI1, SI2 VIHS RST, MOD0, MOD1, INT20 to INT27, UCK1, UI1, INT10 to INT13, SCK1, EC, PWCK, PWC, SCK2, UCK2, UI2, ADST Value Unit Typ Max 0.7 VCC VCC + 0.3 V 0.8 VCC VCC + 0.3 V VSS + 1.4 VSS + 5.5 V With SMB input buffer selected* 0.7 VCC VSS + 5.5 V With I2C input buffer selected* VIL P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P60 to P64, SI1, SI2 VSS - 0.3 0.3 VCC V VILS RST, MOD0, MOD1, INT20 to INT27, UCK1, UI1, INT10 to INT13, SCK1, EC, PWCK, PWC, SCK2, UCK2, UI2, ADST VSS - 0.3 0.2 VCC V VSS - 0.3 VSS + 0.6 V With SMB input buffer selected* 0.3 VCC V With I2C input buffer selected* VCC + 0.3 V VSS + 5.5 V VIHSMB SCL, SDA VIHI2C "L" level input voltage VILSMB SCL, SDA VILI2C Open drain output applied voltage "H" level output voltage "L" level output voltage Remarks Min VD1 P50 to P57 VD2 P42, P43 VOH P00 to P07, P10 to P17, P20 to P24, P30 to P37, IOH = -2.0 mA P40, P41, P44 to P47 P25 to P27 VOL VSS - 0.3 VSS - 0.3 2.4 V 0.4 V IOH = -3.0 mA P00 to P07, P10 to P17, P20 to P27, P30 to P37, IOL = 4.0 mA P40 to P47, P50 to P57, RST (Continued) 40 DS07-12547-7E MB89530A Series (Continued) Parameter Input leak current (Hi-Z output leak current) Open drain output leak current Pin name Symbol ILI (AVCC = VCC = 3.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Value Condition Unit Remarks Min Typ Max P00 to P07, P10 to P17, P20 to P27, P30 to P37, 0.0 V < VI < P40 to P47, P50 to P57, VCC P60 to P64 0.0 V < VI < VSS + 5.5 V -5 +5 With no pull-up A resistance specified 5 A ILIOD P42, P43 Pull-up resistance RUP P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40, P41, P44 to P47, P60 to P64, RST 25 70 100 With pull-up resistance specified. k The RST signal is excluded. Pull-down resistance RDOWN MOD0, MOD1 25 70 100 k 6 10 mA 45 Flash memory mA programming/erase MB89F538L 1.5 3 mA 2 4 mA Sleep mode 1 2 mA Sleep mode 1 3 mA 35 90 20 50 15 30 A Sub, sleep modes 5 15 A 1 5 FCH = 10.0 MHz 1 3 TA = +25 C 1 5 A Sub, stop modes A/D conversion mA running A A/D stopped f = 1 MHz 5 15 pF FCH = 10.0 MHz tinst = 0.4 s ICC1 FCH = 10.0 MHz tinst = 6.4 s FCH = 10.0 MHz tinst = 0.4 s FCH = 10.0 MHz tinst = 6.4 s ICC2 ICCS1 ICCS2 Supply current ICCL VCC FCL = 32.768 kHz VCC = 3.0 V TA = +25 C FCL = 32.768 kHz VCC = 3.0 V TA = +25 C TA = +25 C ICCLS ICCT ICCH IA AVCC IAH Input capacitance CIN FCL = 32.768 kHz VCC = 3.0 V TA = +25 C Except VCC, VSS, AVCC, AVSS Sub modes MB89P538/PV530 Sub modes A MB89F538L Sub modes A MB89535A/7A/8A MB89537AC/538AC Watch mode, main stop * : The MB89PV530/P538/F538L/537AC/538AC have a built-in I2C function, and a choice of input buffers by software setting. MB89535A/537A/538A have no built-in I2C functions, and therefore this standard does not apply. DS07-12547-7E 41 MB89530A Series 4. AC Characteristics (1) Reset Timing (VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Symbol Condition tZLZH RST "L" pulse width Value Min Max 48 tHCYL Unit ns Notes: * tHCYL is the main clock oscillator period. * If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunctions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST). tZLZH RST 0.2 VCC 0.2 VCC (2) Power-on Reset (AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Power on time Power shutoff time Symbol Condition tR tOFF Value Unit Min Max 0.5 50 ms 1 ms Remarks Waiting time until power-on Note : Be sure that the power supply will come on within the selected oscillator stabilization period. Also, when varying the supply voltage during operation, it is recommended that the supply voltage be increased gradually. tR tOFF 2.2 V VCC 0.2 V 42 0.2 V 0.2 V DS07-12547-7E MB89530A Series (3) Clock Timing Standards (AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Symbol Pin name Clock frequency Clock cycle time Input clock pulse width Input clock rise, fall time Condition Value Min Typ Max Unit Remarks FCH X0, X1 1 12.5 MHz Main clock FCL X0A, X1A 32.768 kHz Sub clock tHCYL X0, X1 80 1000 ns Main clock tLCYL X0A, X1A 30.5 s Sub clock PWH PWL X0 20 ns External clock PWHL PWLL X0A 15.2 s External clock tCR tCF X0 10 ns External clock * X0, X1 timing and application conditions tHCYL PWH PWL tCR tCF 0.8 VCC 0.8 VCC X0 0.2 VCC 0.2 VCC 0.2 VCC * Clock application conditions Using a crystal oscillator or ceramic oscillator X0 X1 X0 FCH C1 DS07-12547-7E Using an external clock signal C2 X1 Open FCH 43 MB89530A Series * X0A, X1A timing and application conditions tLCYL PWHL PWLL tCR tCF 0.8 VCC 0.8 VCC X0A 0.2 VCC 0.2 VCC 0.2 VCC * Clock application conditions Using a crystal oscillator or ceramic oscillator X0A Using an external clock signal X1A X0A Rd FCL C1 X1A Open FCL C2 (4) Instruction Cycle (AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Instruction cycle (minimum instruction execution time) 44 Symbol Rated value Unit Remarks 4/FCH, 8/FCH, 16/FCH, 64/FCH s Operating at FCH = 12.5 MHz (4/FCH) tinst = 0.32 s 2/FCL s Operating at FCL = 32.768 kHz tinst = 61.036 s tinst DS07-12547-7E MB89530A Series (5) Serial I/O Timing (VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Symbol Pin name Condition Serial clock cycle time tSCYC SCK, UCK SCKSO tSLOV SCK, SO, UCK, UO Valid SISCK tIVSH SI, SCK, UI, UCK SCKvalid SI hold time tSHIX SCK, SI, UCK, UI Serial clock "H" pulse width tSHSL Serial clock "L" pulse width tSLSH SCKSO time tSLOV SCK, SO, UCK, UO Valid SISCK tIVSH SI, SCK, UI, UCK SCK valid SI hold time tSHIX SCK, SI, UCK, UI Internal clock operation SCK, UCK External clock operation Value Unit Min Max 2 tinst s -200 +200 ns 200 ns 200 ns 1 tinst s 1 tinst s 0 200 ns 200 ns 200 ns Note : For tinst refer to " (4) Instruction Cycle". Internal shift clock mode tSCYC SCK UCK 2.4 V 0.8 V 0.8 V tSLOV SO UO 2.4 V 0.8 V tIVSH tSHIX 0.8 VCC 0.2 VCC SI UI 0.8 VCC 0.2 VCC External shift clock mode tSLSH tSHSL SCK UCK 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC tSLOV SO UO 2.4 V 0.8 V tIVSH SI UI DS07-12547-7E 0.8 VCC 0.2 VCC tSHIX 0.8 VCC 0.2 VCC 45 MB89530A Series (6) Peripheral Input Timing (VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Parameter Symbol Pin name Condition Peripheral input "H" level pulse width 1 tILIH1 Peripheral input "L" level pulse width 1 tIHIL1 INT10 to INT13, INT20 to INT27, EC, PWC, PWCK Peripheral input "H" level pulse width 2 tILIH2 Peripheral input "L" level pulse width 2 tIHIL2 Value Unit Min Max 2 tinst s 2 tinst s 28 tinst s 28 tinst s ADST Note : For tinst refer to " (4) Instruction Cycle". tIHIL1 EC, INT, PWC, PWCK tILIH1 0.8 VCC 0.2 VCC 0.2 VCC tIHIL2 ADST tILIH2 0.8 VCC 0.2 VCC 46 0.8 VCC 0.8 VCC 0.2 VCC DS07-12547-7E MB89530A Series (7) I2C Timing (VCC = 5.0 V, AVss = Vss = 0 V, TA = -40 C to +85 C) Symbol Pin name Condition Start condition output tSTA SCL SDA Stop condition output tSTO SCL SDA Start condition detection tSTA SCL SDA Stop condition detection tSTO Restart condition output Restart condition detection Parameter Value Min Max 1 / 4 tinst x m x n - 20 1 / 4 tinst x m x n + 20 Unit Remarks ns Master only 1 / 4 tinst x 1 / 4 tinst x (m x n + 8) - 20 (m x n + 8) + 20 ns Master only 1 / 4 tinst x 6 + 40 ns SCL SDA 1 / 4 tinst x 6 + 40 ns tSTASU SCL SDA 1 / 4 tinst x 1 / 4 tinst x (m x n + 8) - 20 (m x n + 8) + 20 ns tSTASU SCL SDA 1 / 4 tinst x 4 + 40 ns SCL output "L" width tLOW SCL 1 / 4 tinst x m x n - 20 1 / 4 tinst x m x n + 20 ns Master only SCL output "H" width tHIGH SCL 1 / 4 tinst x 1 / 4 tinst x (m x n + 8) - 20 (m x n + 8) + 20 ns Master only SDA output delay time tDO SDA 1 / 4 tinst x 4 - 20 1 / 4 tinst x 4 + 20 ns Setup after SDA output interrupt interval tDOSU SDA 1 / 4 tinst x 4 - 20 ns SCL input "L" width tLOW SCL 1 / 4 tinst x 6 + 40 ns SCL input "H" width tHIGH SCL 1 / 4 tinst x 2 + 40 ns SDA input setup tSU SDA 40 ns SDA input hold tHO SDA 0 ns Master only Notes : * For tinst refer to " (4) Instruction Cycle". * The value "m" in the above table is the value from the shift clock frequency setting bits (CS4, CS3) in the I2C clock control register "ICCR". For details, refer to the register description in the hardware manual. * The value 'n' in the above table is the value from the shift clock frequency setting bits (CS2, CS0) in the I2C clock control register "ICCR". For details, refer to the register description in the hardware manual. * tDOSU appears when the interrupt period is longer than the SCL "L" width. * The rated values for SDA and SCL assume a start up time of 0 ns. DS07-12547-7E 47 MB89530A Series * I2C interface [Data sending (master/slave) ] tSU tDO tDO tSU tDOSU SDA ACK tSTASU tSTA tLOW SCL tHO 9 1 * I2C interface [Data receiving (master/slave) ] tHO tSU tDO tDO tDOSU SDA ACK tHIGH tLOW tSTO SCL 6 48 7 8 9 DS07-12547-7E MB89530A Series 5. A/D Converter Electrical Characteristics (1) MB89535A/537A/537AC/538A/538AC/P538/PV530 (VCC = 3.5 V to 5.5 V, AVSS = VSS = 0 V, TA = -40 C to +85 C) Value Symbol Pin name Condition Parameter Unit Remarks Min Typ Max Resolution capability 10 bit Total error 3.0 LSB Linear error 2.5 LSB Differential linear error 1.9 LSB AVCC = VCC AVSS - AVSS + AVSS + AVR = AVCC V Zero transition voltage VOT 1.5 LSB 0.5 LSB 2.5 LSB AVR - AVR - AVR + Full scale transition V VFST 3.5 LSB 1.5 LSB 1.5 LSB voltage Inter-channel variation 4.0 LSB Conversion time 60 tinst s * Sampling time 16 tinst s Analog input current IAIN 10 A AN0 to AN7 0 AVR V Analog input voltage VAIN AVCC V Reference voltage AVSS + 3.5 AVR IR A/D running 400 A Reference voltage supply current A/D off 5 A IRH * : Includes sampling time. Note : For tinst refer to "4. AC Characteristics (4) Instruction Cycle". (2) MB89F538 (VCC = 3.5 V to 5.5 V, AVSS = VSS = 0 V, TA = -40 C to +85 C) Value Symbol Pin name Condition Unit Remarks Parameter Min Typ Max Resolution capability 10 bit Total error 5.0 LSB Linear error 2.5 LSB Differential linear error 1.9 LSB AVCC = VCC AVSS - AVSS + AVSS + AVR = AVCC V Zero transition voltage VOT 1.5 LSB 0.5 LSB 4.5 LSB AVR - AVR - AVR + Full scale transition V VFST 6.5 LSB 1.5 LSB 1.5 LSB voltage Inter-channel variation 4.0 LSB s * Conversion time 60 tinst s Sampling time 16 tinst Analog input current IAIN 10 A AN0 to AN7 0 AVR V Analog input voltage VAIN AVCC V Reference voltage AVSS + 3.5 AVR A/D running 400 A IR Reference voltage supply current A/D off 5 A IRH * : Includes sampling time. Note : For tinst refer to "4. AC Characteristics (4) Instruction Cycle". DS07-12547-7E 49 MB89530A Series (3) MB89F538L Parameter Symbol Pin name Resolution capability Total error Linear error (VCC = 2.4 V to 3.6 V, AVSS = VSS = 0 V, TA = -40 C to +85 C) Value Condition Unit Remarks Min Typ Max 10 bit 3.0 LSB 2.5 LSB Differential linear error 1.9 LSB Zero transition voltage VOT AVSS - 1.5 LSB AVSS + 0.5 LSB AVSS + 2.5 LSB V Full scale transition voltage VFST AVR - 3.5 LSB AVR - 1.5 LSB AVR + 1.5 LSB V 4.0 LSB 60 tinst s 16 tinst s 10 A 0 AVR V AVSS + 2.4 AVCC V A/D running 200 A A/D off 5 A AVR = AVCC Inter-channel variation Conversion time Sampling time Analog input current IAIN Analog input voltage VAIN Reference voltage Reference voltage supply current IR IRH AN0 to AN7 AVR AVCC = VCC * * : Includes sampling time 50 DS07-12547-7E MB89530A Series (4) A/D Converter Terms and Definitions * Resolution The level of analog variation that can be distinguished by the A/D converter. * Linear error (unit : LSB) The deviation between the value along a straight line connecting the zero transition point ("00 0000 0000""00 0000 0001") of a device and the full-scale transition point ("11 1111 1110""11 1111 1111") , compared with the actual conversion values obtained. * Differential linear error (Unit : LSB) The deviation from the theoretical input voltage required to produce a change of 1 LSB in output code. * Total error (Unit : LSB) The difference between theoretical conversion value and actual conversion value. Theoretical input/output characteristics Total error VFST 3FFH 3FFH 3FEH 1.5 LSB 3FDH 004H 003H VOT 002H Digital output Digital output 3FEH 3FDH Actual conversion characteristics (1 LSB I N + 0.5 LSB) 004H VNT 003H 002H 1 LSB 001H 001H Actual conversion characteristics Theoretical characteristics 0.5 LSB AVSS AVR Analog input 1 LSB = VFST - VOT 1022 (V) AVSS AVR Analog input Total error in digital output N = VNT - {1 LSB x N + 0.5 LSB} 1 LSB (Continued) DS07-12547-7E 51 MB89530A Series (Continued) Zero transition error Full-scale transition error Actual conversion characteristics 004H Theoretical characteristics Actual conversion characteristics 3FFH Digital output Digital output 003H 002H Actual conversion characteristics 001H VOT (actual measurement value) AVSS VFST (actual measurement value) 3FDH Actual conversion characteristics 3FCH AVR Analog input 3FEH AVSS Linear error Actual conversion characteristics 3FEH Digital output Differential linear error N + 1H (1 LSB x N + VOT) 3FDH VFST 004H 003H 002H 001H (actual VNT measurement value) Actual conversion characteristics Theoretical characteristics VOT (actual measurement value) AVSS AVR Analog input Analog input linear = VNT - {1 LSB x N + VOT} 1 LSB error in digital output N 52 Digital output 3FFH AVR Analog input Theoretical characteristics Actual conversion V (N + 1) T characteristics NH N - 1H N - 2H AVSS VNT Actual conversion characteristics Analog input AVR Differential linear = V (N + 1) T - VNT -1 1 LSB error in digital output N DS07-12547-7E MB89530A Series (5) Precautionary Information * Input Impedance of Analog Input Pins The A/D converter of MB89530A has a sample & hold circuit as shown below, which uses a sample-and-hold capacitor to obtain the voltage at the analog input pin for 8 instruction cycles following the start of A/D conversion. For this reason if the external circuits providing the analog input signal have high output impedance, the analog input voltage may not stabilize within the analog input sampling time. It is therefore recommended that the output impedance of external circuits be reduced to 10 k or less. * Analog Input Equivalent Circuit Sample-and-hold circuit C Analog input pin Comparator R If analog input impedance is 10 k or more, the use of a capacitor of approximately 0.1 F is recommended. Closes 8 instruction cycles after the start of A/D conversion Analog channel selector MB89535A/537A/537AC/538A/538AC C =: 45 pF R =: 2.2 k MB89F538 C =: 30 pF R =: 3.2 k MB89F538L C =: 49 pF R =: 7.1 k MB89P538, MB89P530 C =: 64 pF R =: 3.0 k * About error The smaller the absolute value |AVR - AVss| is, the greater the relative error becomes. DS07-12547-7E 53 MB89530A Series 6. Flash Memory * Flash memory programming/erase characteristics Parameter Sector erase time Per 1 sector, Constant value independent with sector capacitance Programming Per 1 byte time Conditions TA = +25 C, VCC = 5.0 V Chip erase time Program/Erase cycle Value Unit Min Typ Max 1 15 s 8 3600 s 5 s 10000 cycle Remarks * * * : Excludes internal programming time before erase. 54 DS07-12547-7E MB89530A Series EXAMPLE CHARACTERISTICS (MB89538A) (1) Power Supply Current (External Clock) ICC1 vs. VCC ICCS1 vs. VCC 14 5 (TA = + 25 C) 12 12.5 MHz 4 8 ICCS1 (mA) 10 MHz 10 ICC1 (mA) (TA = + 25 C) 12.5 MHz 8 MHz 6 5 MHz 10 MHz 3 8 MHz 2 5 MHz 4 1 2 MHz 1 MHz 2 0 2 MHz 1 MHz 0 2 3 4 5 6 7 2 3 4 VCC (V) 5 6 7 VCC (V) (2) "H" Level Input Voltage/ "L" Level Input Voltage (CMOS Input) VIN vs. VCC 4 (TA = + 25 C) VIN (V) 3 2 1 0 2 3 4 5 6 7 VCC (V) (3) "H" Level Input Voltage / "L" Level Input Voltage (Hysteresis Input) VIN vs. VCC 4 VIH (TA = + 25 C) VIN (V) 3 VIL 2 1 0 2 3 4 5 6 7 VCC (V) DS07-12547-7E 55 MB89530A Series (4) Pull-up Resistor Value RPULL vs. VCC 1000 Pull-up (k) (TA = + 25 C) 100 10 1 0 2 3 4 5 6 VCC (V) (5) "H" Level Output Voltage VCC - VOH1 vs. IOH VCC - VOH2 vs. IOH 1.6 0.9 0.8 1.2 0.7 VCC - VOH2 (V) VCC - VOH1 (V) (TA = + 25 C, VCC = 5 V) 1.4 1.0 0.8 0.6 0.4 (TA = + 25 C, VCC = 5 V) 0.6 0.5 0.4 0.3 0.2 0.2 0.1 0.0 0.0 0 2 4 6 8 10 0 2 IOH (mA) 4 6 8 10 IOH (mA) (6) "L" Level Output Voltage VCC - VOL vs. IOL 0.9 (TA = + 25 C, VCC = 5 V) 0.8 VCC - VOL (V) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 2 4 6 8 10 IOL (mA) 56 DS07-12547-7E MB89530A Series (7) AD Converter Characteristic Example Linearity Error 3.0 2.5 (VCC = AVR = 5 V, FCH = 10 MHz) 2.0 Error (LSB) 1.5 1.0 0.5 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 0 128 256 384 512 640 768 896 1024 768 896 1024 768 896 1024 Conversion characteristic Differential linearity error 2.5 2.0 1.5 Error (LSB) 1.0 0.5 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 0 128 256 384 512 640 Conversion characteristic Total Error 4.0 3.0 (VCC = AVR = 5 V, FCH = 10 MHz) Error (LSB) 2.0 1.0 0.0 -1.0 -2.0 -3.0 -4.0 0 128 256 384 512 640 Conversion characteristic DS07-12547-7E 57 MB89530A Series MASK OPTIONS Part number MB89535A MB89537A MB89537AC MB89538A MB89538AC MB89F538-101 MB89F538-201 MB89F538L-101 MB89F538L-201 MB89P538-101 MB89P538-201 MB89PV530-101 Method of specification Specify at time of mask order Setting not possible Setting not possible Setting not possible 1 Main clock Select oscillator stabilization wait period (FCH* = 10 MHz) approx.214/FCH* (approx.1.6 ms) approx.217/FCH* (approx.13.1 ms) approx.218/FCH* (approx.26.2 ms) Selection available 218/FCH* (approx. 26.2 ms) 218/FCH* (approx. 26.2 ms) 218/FCH* (approx. 26.2 ms) 2 Clock mode selection * 2-system clock mode * 1-system clock mode Selection available No MB89PV530-201 * 101 : 1-system clock mode * 201 : 2-system clock mode * : FCH: Main clock frequency 58 DS07-12547-7E MB89530A Series ORDERING INFORMATION Part number Package Remarks MB89535AP MB89537AP MB89537ACP MB89538AP MB89538ACP MB89P538-101P MB89P538-201P MB89F538-101P MB89F538-201P MB89F538L-101P MB89F538L-201P DIP-64P-M01 MB89535AP, MB89537AP and MB89538AP do not have I2C functions. MB89535APF MB89537APF MB89537ACPF MB89538APF MB89538ACPF MB89P538-101PF MB89P538-201PF MB89F538-101PF MB89F538-201PF MB89F538L-101PF MB89F538L-201PF FPT-64P-M06 MB89535APF, MB89537APF and MB89538APF do not have I2C functions. MB89535APMC MB89537APMC MB89537ACPMC MB89538APMC MB89538ACPMC MB89P538-101PMC MB89P538-201PMC MB89F538-101PMC MB89F538-201PMC MB89F538L-101PMC MB89F538L-201PMC FPT-64P-M23 MB89535APMC, MB89537APMC and MB89538APMC do not have I2C functions. MB89535APMC1 MB89537APMC1 MB89537ACPMC1 MB89538APMC1 MB89538ACPMC1 FPT-64P-M24 MB89535APMC1, MB89537APMC1 and MB89538APMC1 do not have I2C functions. MB89535APV4 MB89537APV4 MB89537ACPV4 MB89538APV4 MB89538ACPV4 MB89F538L-101PV4 MB89F538L-201PV4 LCC-64P-M19 MB89535APV4, MB89537APV4, and MB89538APV4 do not have I2C functions. MB89PV530-101C MB89PV530-201C MDP-64C-P02 MB89PV530-101CF MB89PV530-201CF MQP-64C-P01 DS07-12547-7E 59 MB89530A Series PACKAGE DIMENSIONS 64-pin plastic SH-DIP Lead pitch 1.778mm(70mil) Package width x package length 17 x 58 mm Sealing method Plastic mold Mounting height 5.65 mm MAX (DIP-64P-M01) 64-pin plastic SH-DIP (DIP-64P-M01) Note: Pins width and pins thickness include plating thickness. +0.22 +.009 58.00 -0.55 2.283 -.022 INDEX-1 17.000.25 (.669.010) INDEX-2 +0.70 4.95 -0.20 +.028 .195 -.008 +0.50 0.70 -0.19 +.020 .028 -.007 0.270.10 (.011.004) +0.20 3.30 -0.30 .130 +.008 -.012 +0.40 1.378 -0.20 .0543 C +.016 -.008 1.778(.0700) 0.470.10 (.019.004) 19.05(.750) +0.50 0.25(.010) M 2001-2008 FUJITSU MICROELECTRONICS LIMITED D64001S-c-4-6 1.00 -0 .039 +.020 -.0 0~15 Dimensions in mm (inches). Note: The values in parentheses are reference values. Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/ (Continued) 60 DS07-12547-7E MB89530A Series 64-pin plastic LQFP Lead pitch 0.50 mm Package width x package length 10.0 x 10.0 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 1.70 mm MAX Weight 0.32 g Code (Reference) P-LFQFP64-10x10-0.50 (FPT-64P-M24) 64-pin plastic LQFP (FPT-64P-M24) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 12.000.20(.472.008)SQ * 10.000.10(.394.004)SQ 48 0.1450.055 (.006.002) 33 49 32 Details of "A" part 0.08(.003) +0.20 1.50 -0.10 +.008 .059 -.004 INDEX 64 0~8 17 (Mounting height) 0.100.10 (.004.004) (Stand off) "A" LEAD No. 1 16 0.50(.020) 0.200.05 (.008.002) 0.08(.003) M (c)2005-2008 FUJITSU MICROELECTRONICS LIMITED F64036S-c-1-2 C 2005 FUJITSU LIMITED F64036S-c-1-1 0.500.20 (.020.008) 0.600.15 (.024.006) 0.25(.010) Dimensions in mm (inches). Note: The values in parentheses are reference values Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/ (Continued) DS07-12547-7E 61 MB89530A Series 64-pin plastic QFP Lead pitch 1.00 mm Package width x package length 14 x 20 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 3.35 mm MAX Code (Reference) P-QFP64-14x20-1.00 (FPT-64P-M06) 64-pin plastic QFP (FPT-64P-M06) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 24.700.40(.972.016) * 20.000.20(.787.008) 51 0.170.06 (.007.002) 33 32 52 18.700.40 (.736.016) *14.000.20 (.551.008) INDEX Details of "A" part +0.35 3.00 -0.20 +.014 .118 -.008 (Mounting height) 20 64 0~8 1 19 1.00(.039) 0.420.08 (.017.003) 0.20(.008) +0.15 M 0.25 -0.20 1.200.20 (.047.008) +.006 .010 -.008 (Stand off) "A" 0.10(.004) C 2003-2008 FUJITSU MICROELECTRONICS LIMITED F64013S-c-5-6 Dimensions in mm (inches). Note: The values in parentheses are reference values. Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/ (Continued) 62 DS07-12547-7E MB89530A Series 64-pin plastic LQFP Lead pitch 0.65 mm Package width x package length 12.0 x 12.0 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 1.70 mm MAX Code (Reference) P-LFQFP64-12x12-0.65 (FPT-64P-M23) 64-pin plastic LQFP (FPT-64P-M23) Note 1) * : These dimensions do not include resin protrusion. Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 14.000.20(.551.008)SQ *12.000.10(.472.004)SQ 48 0.1450.055 (.0057.0022) 33 32 49 0.10(.004) Details of "A" part +0.20 1.50 -0.10 +.008 (Mounting height) .059 -.004 0.25(.010) INDEX 0~8 17 64 1 "A" 16 0.65(.026) 0.320.05 (.013.002) 0.13(.005) 0.500.20 (.020.008) 0.600.15 (.024.006) 0.100.10 (.004.004) (Stand off) M (c)2003-2008 FUJITSU LIMITED F64034S-c-1-2 C 2003 FUJITSU LIMITEDMICROELECTRONICS F64034S-c-1-1 Dimensions in mm (inches). Note: The values in parentheses are reference values Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/ (Continued) DS07-12547-7E 63 MB89530A Series 64-pin plastic BCC Lead pitch 0.50 mm Package width x package length 9.00 mm x 9.00 mm Sealing method Plastic mold Mounting height 0.80 mm MAX Weight 0.10g (LCC-64P-M19) 64-pin plastic BCC (LCC-64P-M19) 49 8.20(.323)TYP 8.10(.319)TYP (0.80(.031)MAX) (Mount height) 9.000.10(.354.004) 33 0.50(.020) TYP 33 0.500.10 (.020.004) 49 0.50(.020) TYP 8.25(.325) REF INDEX AREA 9.000.10 (.354.004) 8.20(.323) TYP 8.10(.319) TYP 7.00(.276) REF 0.500.10 (.020.004) "A" 1 17 0.0750.025 17 "C" (.003.001) (Stand off) Details of "A" part 0.05(.002) C 2002 FUJITSU LIMITED C64019S-c-1-1 0.600.06 (.024.002) 0.300.06 (.012.002) 0.14(.006)MIN. 0.700.06 (.028.002) 0.300.06 (.012.002) (c)2002-2008 FUJITSU MICROELECTRONICS LIMITED C64019S-c-1-2 7.00(.276)REF "B" 1 8.25(.325)REF Details of "B" part 0.550.06 (.022.002) C0.2(.008) 0.550.06 (.022.002) Details of "C" part 0.550.06 (.022.002) 0.550.06 (.022.002) Dimensions in mm (inches). Note: The values in parentheses are reference values. Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/ (Continued) 64 DS07-12547-7E MB89530A Series 64-pin ceramic MDIP Lead pitch 1.778mm (70mil) Row spacing 19.05mm (750mil) Motherboard material Ceramic Mounted packing material Plastic (MDP-64C-P02) 64-pin ceramic MDIP (MDP-64C-P02) 0~9 56.900.64 (2.240.025) 15.24(.600) TYP 18.750.30 (.738.012) INDEX AREA 2.540.25 (.100.010) 33.02(1.300)REF 0.250.05 (.010.002) 1.270.25 (.050.010) 10.16(.400)MAX 1.7780.25 (.070.010) C 19.050.30 (.750.012) +0.13 0.46 -0.08 +.005 .018 -.003 55.12(2.170)REF 0.900.13 (.035.005) 1994-2008 FUJITSU MICROELECTRONICS LIMITED M64002SC-1-5 3.430.38 (.135.015) Dimensions in mm (inches). Note: The values in parentheses are reference values. Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/ (Continued) DS07-12547-7E 65 MB89530A Series (Continued) 64-pin ceramic MQFP Lead pitch 1.00 mm Lead shape Straight Motherboard material Ceramic Mounted package material Plastic (MQP-64C-P01) 64-pin ceramic MQFP (MQP-64C-P01) 18.70(.736)TYP INDEX AREA 16.300.33 (.642.013) 15.580.20 (.613.008) 12.00(.472)TYP +0.40 1.20 0.20 .047 1.000.25 (.039.010) +.016 .008 1.000.25 (.039.010) 1.270.13 (.050.005) 18.120.20 12.02(.473) (.713.008) TYP 10.16(.400) 14.22(.560) TYP TYP 22.300.33 (.878.013) 24.70(.972) TYP 0.30(.012) TYP 1.270.13 (.050.005) 0.30(.012)TYP 7.62(.300)TYP 18.00(.709) TYP 0.400.10 (.016.004) 0.400.10 (.016.004) +0.40 1.20 0.20 +.016 .047 .008 9.48(.373)TYP 11.68(.460)TYP 0.50(.020)TYP C 10.82(.426) 0.150.05 MAX (.006.002) 1994-2008 FUJITSU MICROELECTRONICS LIMITED M64004SC-1-4 Dimensions in mm (inches). Note: The values in parentheses are reference values. Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/ 66 DS07-12547-7E MB89530A Series MAIN CHANGES IN THIS EDITION Page Section Added the part number. MB89F538L Changed the package code. FPT-64P-M03 FPT-64P-M24 FPT-64P-M09 FPT-64P-M23 Deleted LCC-64P-M16 . Change Results 19 PROGRAMMING AND ERASING FLASH Deleted the "6. ROM Programmer Adaptor and MEMORY ON THE MB89F538/F538L Recommended ROM Programmers". 20 ONE-TIME WRITING SPECIFICATIONS WITH PROM AND EPROM Deleted the "* ROM writer adapters". MICROCONTROLLERS 22 EPROM WRITING TO PIGGY-BACK/ EVALUATION CHIPS 49 ELECTRICAL CHARACTERISTICS 5. A/D Converter Electrical Characteristics 53 DS07-12547-7E Deleted the "* Writer adapter". Changed the unit of Zero transition voltage and Full scale transition voltage mV V Changed the figure of "* Input Impedance of Analog Input Pins". 67 MB89530A Series Page Section ORDERING INFORMATION 63 Added the order informations. MB89F538L-101P, MB89F538L-201P MB89F538L-101PF, MB89F538L-201PF MB89F538L-101PMC, MB89F538L-201PMC MB89F538L-101PV4, MB89F538L-201PV4 Changed the order informations. MB89P538P-101 MB89P538-101P MB89P538P-201 MB89P538-201P MB89F538P-101 MB89F538-101P MB89F538P-201 MB89F538-201P MB89P538PF-101 MB89P538-101PF MB89P538PF-201 MB89P538-201PF MB89F538PF-101 MB89F538-101PF MB89F538PF-201 MB89F538-201PF MB89535APFM MB89535APMC MB89537APFM MB89537APMC MB89537ACPFM MB89537ACPMC MB89538APFM MB89538APMC MB89538ACPFM MB89538ACPMC MB89P588PFM-101 MB89P538-101PMC MB89P588PFM-201 MB89P538-201PMC MB89F538PFM-101 MB89F538-101PMC MB89F538PFM-201 MB89F538-201PMC MB89535APFV MB89535APMC1 MB89537APFV MB89537APMC1 MB89537ACPFV MB89537ACPMC1 MB89538APFV MB89538APMC1 MB89538ACPFV MB89538ACPMC1 MB89PV530C-101 MB89PV530-101C MB89PV530C-201 MB89PV530-201C MB89PV530CF-101 MB89PV530-101CF MB89PV530CF-201 MB89PV530-201CF 59 61 Change Results PACKAGE DIMENSIONS Changed the package figure. FPT-64P-M03 FPT-64P-M24 Changed the package figure. FPT-64P-M09 FPT-64P-M23 The vertical lines marked in the left side of the page show the changes. MB89530A Series MEMO DS07-12547-7E 69 MB89530A Series MEMO 70 DS07-12547-7E MB89530A Series MEMO DS07-12547-7E 71 MB89530A Series FUJITSU MICROELECTRONICS LIMITED Shinjuku Dai-Ichi Seimei Bldg., 7-1, Nishishinjuku 2-chome, Shinjuku-ku, Tokyo 163-0722, Japan Tel: +81-3-5322-3347 Fax: +81-3-5322-3387 http://jp.fujitsu.com/fml/en/ For further information please contact: North and South America FUJITSU MICROELECTRONICS AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel: +1-408-737-5600 Fax: +1-408-737-5999 http://www.fma.fujitsu.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LTD. 151 Lorong Chuan, #05-08 New Tech Park 556741 Singapore Tel : +65-6281-0770 Fax : +65-6281-0220 http://www.fmal.fujitsu.com/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://emea.fujitsu.com/microelectronics/ FUJITSU MICROELECTRONICS SHANGHAI CO., LTD. Rm. 3102, Bund Center, No.222 Yan An Road (E), Shanghai 200002, China Tel : +86-21-6146-3688 Fax : +86-21-6335-1605 http://cn.fujitsu.com/fmc/ Korea FUJITSU MICROELECTRONICS KOREA LTD. 206 Kosmo Tower Building, 1002 Daechi-Dong, Gangnam-Gu, Seoul 135-280, Republic of Korea Tel: +82-2-3484-7100 Fax: +82-2-3484-7111 http://kr.fujitsu.com/fmk/ FUJITSU MICROELECTRONICS PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel : +852-2377-0226 Fax : +852-2376-3269 http://cn.fujitsu.com/fmc/en/ Specifications are subject to change without notice. For further information please contact each office. All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited: Business & Media Promotion Dept.