VT-501 Temperature Compensated Crystal Oscillator Previous Vectron Model VTD3 VT-501 Description Vectron's VT-501 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, CMOS output, analog temperature compensated oscillator, operating off either 3.3 or 5.0 volt supply, 9.9x11.8 FR4 board with a nickel cover. Features * * * * * * Applications CMOS Output Output Frequencies to 61.440 MHz Fundamental Crystal Design Optional VCXO Function available Gold over nickel contact pads Hermetically Sealed Ceramic SMD package * * * * * Wireless Communications Base Stations Point to point radios Broadband Access Test Equipment * Product is compliant to RoHS directive and fully compatible with lead free assembly Block Diagram Output VDD Crystal Analog Temperature Comp. Vcontrol or NC Gnd Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page1 Performance SpecifiSpecifi cationscations Table 1. Electrical Performance Parameter Symbol Min. fO 8 Output Frequency 1 Typ Max Units 61.440 MHz Supply Voltage VDD Supply Current, 8-22MHz >22MHz IDD +3.3 or +5.0 15 24 mA Operating Temperature, ordering option TOP 0/55, -10/60, -20/70, -30/80, -40/85 C Stability Over TOP, ordering option V 1.0, 1.5, 2.0, 2.5, 3.0, 4.0, 5.0 ppm Initial Accuracy, "No Adjust" Option 2.0 ppm Power Supply Stability 1.0 ppm Load Stability 0.3 ppm 1.0 ppm/yr Aging Pull Range TPR 5, 8, 10, 12, 15 Control Voltage to reach Pull Range, 5V 3.3V option 0.5 0.3 Control Voltage Impedance 100 ppm 4.5 3.0 V kohm 2 Output Level Output High Output Low Output High Drive Output Low Drive VOH VOL IOH IOL 0.9*VDD V V mA mA 0.1*VDD -4 4 Output Load 15 pF Duty Cycle 40/60 Phase Noise, 10.000MHz 10Hz 100Hz 1kHz 10kHz 100kHz % dBc/Hz -107 -138 -148 -152 -154 Start Up Time 10 ms 1. The VT-501 power supply pin should be filtered, eg, a 0.1 and 0.01uf capacitor 2. The Output is DC coupled 3. Duty Cycle is On Time/Period, see Figure 2. Test Circuit is shown in Figure 1. Outline Drawing 9.9 Description Recommended Pad Layout 1.30.1 1.9 0.7 7.62 1.4 7.62 Frequency Date Code 11.8 1.20.1 8.4 Dimensions in mm Table 2. Pinout Pin # 2.2 1.4 Symbol Function 1 VC TCXO Control Voltage or Ground 2 GND Electrical and Lid Ground 3 fo Output Frequency 4 VDD Supply Voltage Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page2 Test Circuit tR IDD tF VOH + VDD - .1F .01F IC VC 4 3 1 2 50% VOL 15pF On Time + - Period Figure 1 Test Circuit Figure 2 Duty Cycle, On Time/Period Phase Noise and Alan Deviation Plot Figure 3 Phase Noise Plot for a 10.000MHz output Figure 4 Alan Deviation Plot for a 10.000MHz output S VCXO Function VCXO Feature: The VT-501 can be ordered with a VCXO function for applications were it will be used in a PLL, or the output frequency needs fine tune or calibration adjustments. This is a high impedance input , 1Mohm, and can be driven with an op-amp or terminated with adjustable resistors etc. Pin 1 should not be left floating on the VCXO optional device. "No Adjust" Option: In applications were the VT-501 will not be used in a PLL , or the output frequency does not need fine tune adjustments, the best device to use would be a VT-501-xxx-xxx0. By using the "no adjust" option, the circuit is simplified as Vc does not need to be adjusted or set to a predetermined voltage and pin 1 should be grounded (pin 1 can be left open but should not be set to a voltage such as an RF signal or power supply voltage. Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page3 S Maximum Ratings Absolute Maximum Ratings and Handling Precautions Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied or any other excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. The Although ESD protection circuitry has been designed into the VT-501, proper precautions should be taken when handling and mounting, VI employs a Human Body Model and Charged Device Model for ESD susceptibility testing and design evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry standard has been adopted for the CDM a standard resistance of 1.5kOhms and capacitance of 100pF is widely used and therefor can be used for comparison purposes. Reliability Table 3. Maximum Ratings Parameter Symbol Rating Unit Storage Temperature TSTORE -40/85 C Supply Voltage VDD 7 V Control Voltage VC 0/VDD V ESD, Human Body Model 1000 V ESD, Charged Device Model 500 V Table 4. Environmental Compliance Parameter Condition Mechanical Shock MIL-STD-883 Method 2002 Mechanical Vibration MIL-STD-883 Method 2007 Temperature Cycle MIL-STD-883 Method 1010 Solderability MIL-STD-883 Method 2003 Fine and Gross Leak MIL-STD-883 Method 1014 MIL-STD-883 Method 2015 MSL1 Contact Pads Gold over Nickel S Resistance to Solvents Moisture Sensitivity Level Suggested IR Profile Devices are built using lead free epoxy and can be subjected to standard lead free IR reflow conditions shown in Table 5. Contact pads are gold over nickel and lower maximum temperatures can also be used, such as 220C. Table 5. Reflow Profile Parameter Symbol Value PreHeat Time ts Ts-min Ts-max 200 sec Max 150C 200C Ramp Up RUP 3C/sec Max Time above 217C tL 150 sec Max Time to Peak Temperature t25-PEAK 480 sec Max Time at 260C tP 10 sec Max Time at 240C tP2 60 sec Max Ramp down RDN 6C/sec Max Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page4 IR Reflow Tape & Reel Table 6. Tape and Reel Information Tape Dimensions (mm) Reel Dimensions (mm) W F Do Po P1 A B C D N W1 W2 #/Reel 24 11.5 1.5 4 16 330 2 13 21 80 24.4 28.4 1000 or 2000 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page5 Ordering Information Ordering Information Table 7. Standard Frequencies (MHz) 8.750 9.83040 10.000 10.230 11.000 12.28880 12.3520 12.500 12.800 13.000 14.318180 14.400 20.000 21.400 15.360 16.3840 16.800 18.4140 19.200 19.440 19.6608 19.680 24.9770 25.1658240 25.600 26.880 27.000 30.080 30.720 32.000 32.7680 37.800 38.400 61.440 62.880 44.000 44.7360 46.000 46.080 48.000 50.000 56.000 VT-501- E A G - 206 A - xxMxxxxxxx Frequency in MHz Product TCXO Tuning 0: Fixed, No tuning A: 5ppm B: 8ppm C: 10ppm D: 12ppm E 15ppm Package 9.9x11.8 FR4 Voltage Options D: +5.0 Vdc 5% E: +3.3 Vdc 5% Output A: CMOS Temp Range R: 0 /55C K: -10/60C J: -20/70C G: -30/80C E: -40/85C *Note: not all combination of options are available. Other specifications may be available upon request. Stability 106: 1ppm 156: 1.5ppm 206: 2.0ppm 256: 2.5ppm 306: 3.0ppm 356: 3.5ppm 406: 4.0ppm 506: 5.0ppm Example: VT-501-EAG-206A-19M2000000 For Additional Information, Please Contact USA: Europe: Asia: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 01/10/2009 Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * http://www.vectron.com Page6