IDT7133SA/LA IDT7143SA/LA HIGH SPEED 2K X 16 DUAL-PORT SRAM Features High-speed access - Military: 25/35/45/55/70/90ns (max.) - Industrial: 25/35/55ns (max.) - Commercial: 20/25/35/45/55/70/90ns (max.) Low-power operation - IDT7133/43SA Active: 1150mW (typ.) Standby: 5mW (typ.) - IDT7133/43LA Active: 1050mW (typ.) Standby: 1mW (typ.) Versatile control for write: separate write control for lower and upper byte of each port MASTER IDT7133 easily expands data bus width to 32 bits or more using SLAVE IDT7143 On-chip port arbitration logic (IDT7133 only) BUSY output flag on IDT7133; BUSY input on IDT7143 Fully asynchronous operation from either port Battery backup operation-2V data retention TTL-compatible; single 5V (10%) power supply Available in 68-pin ceramic PGA, Flatpack, PLCC and 100pin TQFP Military product compliant to MIL-PRF-38535 QML Industrial temperature range (-40C to +85C) is available for selected speeds Green parts available, see ordering information Description The IDT7133/7143 are high-speed 2K x 16 Dual-Port Static RAMs. The IDT7133 is designed to be used as a stand-alone 16-bit Dual-Port Functional Block Diagram CE L R/W RUB CER R/W LLB R/WRLB R/WLUB OE R OE L I/O8L - I/O15L I/O CONTROL I/O0L - I/O7L I/O8R - I/O15R I/O CONTROL I/O0R - I/O 7R (1) BUSY R BUSYL(1) A10L A0L MEMORY ARRAY ADDRESS DECODER 11 CE L ADDRESS DECODER A10R A0R 11 ARBITRATION LOGIC CE R (IDT7133 ONLY) 2746 drw 01 NOTE: 1. IDT7133 (MASTER): BUSY is open drain output and requires pull-up resistor. IDT7143 (SLAVE): BUSY is input. OCTOBER 2008 1 (c)2008 Integrated Device Technology, Inc. DSC 2746/13 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges RAM or as a "MASTER" Dual-Port RAM together with the IDT7143 "SLAVE" Dual-Port in 32-bit-or-more word width systems. Using the IDT MASTER/SLAVE Dual-Port RAM approach in 32-bit-or-wider memory system applications results in full-speed, error-free operation without the need for additional discrete logic. Both devices provide two independent ports with separate control, address, and I/O pins that permit independent, asynchronous access for reads or writes to any location in memory. An automatic power down feature, controlled by CE, permits the on-chip circuitry of each 10 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 60 11 59 12 58 13 57 14 56 55 15 16 17 18 19 IDT7133/43 J68-1 / F68-1(4) 54 68-Pin PLCC/Flatpack Top View(5) 52 53 51 20 50 21 49 22 48 23 47 24 46 25 45 I/O8R I/O9R I/O10R I/O11R I/O12R I/O13R I/O14R I/O15R GND(2) R/WRUB R/WRLB OER A10R A9R A8R A7R A6R 44 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 NOTES: 1. Both VCC pins must be connected to the power supply to ensure reliable operation. 2. Both GND pins must be connected to the ground supply to ensure reliable operation. 3. J68-Package body is approximately 0.95 in x 0.95 in x 0.17 in. F68-Package body is approximately 1.18 in x 1.18 in x 0.16 in. PN100-Package body is approximately 14mm x 14mm x 1.4mm. 4. This package code is used to reference the package diagram. 5. This text does not indicate orientation of the actual part-marking. A6L A5L A4L A3L A2L A1L A0L BUSYL CEL CER BUSYR A0R A1R A2R A3R A4R A5R 2746 drw 02 I/O9L I/O8L I/O7L I/O6L I/O5L I/O4L I/O3L I/O2L GND I/O1L I/O0L OEL VCC R/WLLB N/C CEL R/WLUB N/C N/C N/C A10L A9L A8L A7L A6L 9 I/O9L I/O10L I/O11L I/O12L I/O13L I/O14L I/O15L VCC(1) GND(2) I/O0R I/O1R I/O2R I/O3R I/O4R I/O5R I/O6R I/O7R Index N/C N/C N/C N/C I/O10L I/O11L I/O12L I/O13L GND I/O14L I/O15L VCC GND I/O0R I/O1R I/O2R VCC I/O3R I/O4R I/O5R I/O6R N/C N/C N/C N/C 2 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 3 73 4 72 5 71 6 70 7 69 8 68 1 9 10 11 67 IDT7133/43PF PN100-1(4) 12 13 14 66 65 64 100-Pin TQFP Top View(5) 63 62 15 16 61 60 17 18 59 58 19 20 57 56 21 55 22 54 23 53 24 52 51 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 N/C N/C N/C N/C A5L A4L A3L A2L A1L A0L N/C BUSYL GND N/C BUSYR N/C A0R A1R A2R A3R A4R N/C N/C N/C N/C 2746 drw 03 I/O7R I/O8R I/O9R I/O10R I/O11R I/O12R I/O13R I/O14R GND I/O15R OER R/WRLB GND N/C CER R/WRUB N/C N/C N/C A10R A9R A8R A7R A6R A5R INDEX I/O8L I/O7L I/O6L I/O5L I/O4L I/O3L I/O2L I/O1L I/O0L VCC(1) R/WLUB R/WLLB OEL A10L A9L A8L A7L Pin Configurations(1,2,3) port to enter a very low standby power mode. Fabricated using IDT's CMOS high-performance technology, these devices typically operate on only 1,150mW of power. Low-power (LA) versions offer battery backup data retention capability, with each port typically consuming 200W for a 2V battery. The IDT7133/7143 devices have identical pinouts. Each is packed in a 68-pin ceramic PGA, 68-pin flatpack, 68-pin PLCC and 100-pin TQFP. Military grade product is manufactured in compliance with the latest revision of MIL-PRF-38535 QML, making it ideally suited to military temperature applications demanding the highest level of performance and reliability. 6.42 2 , IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Pin Configurations(1,2,3) (con't.) 50 51 11 A6L 53 10 52 55 49 A7L A8L 48 A5L 46 A3L 47 45 A2L A4L 44 A1L 42 BUSYL 43 41 CEL A0L 40 CER 38 A0R 39 BUSYR 36 A2R 37 A1R 35 A3R 54 09 A10L 08 R/WLLB 57 30 OEL 28 06 I/O1L 63 05 I/O0L 65 22 20 I/O6L 1 3 2 01 Pin 1 Designator A 5 I/O11L 4 7 I/O13L 6 9 I/O15L 8 11 GND(2) 10 13 I/O1R 12 15 I/O3R 18 I/O5R 14 16 I/O13R 21 I/O10R I/O9L I/O8L I/O15R 23 I/O12R 66 68 25 I/O14R I/O4L I/O7L 02 24 64 67 OER 27 GND(2) R/WRUB I/O2L I/O5L 03 26 68-Pin PGA Top View(5) 62 I/O3L 04 IDT7133/43G GU68-1(4) A9R 29 R/WRLB 60 A7R 31 A10R 58 A6R 33 A8R VCC(1) R/WLUB 61 34 A5R 32 A9L 56 59 07 A4R I/O11R 19 I/O8R I/O9R 17 I/O10L I/O12L I/O14L VCC(1) I/O0R I/O2R I/O4R I/O6R I/O7R B C D E F G H J K NOTES: 1. Both VCC pins must be connected to the power supply to ensure reliable operation. 2. Both GND pins must be connected to the ground supply to ensure reliable operation. 3. Package body is approximately 1.18 in x 1.18 in x 0.16 in. 4. This package code is used to reference the package diagram. 5. This text does not indicate orientation of the actual part-marking. L 2746 drw 04 Pin Names Left Port Right Port Names CEL CER Chip Enable R/WLUB R/WRUB Upper Byte Read/Write Enable R/WLLB R/WRLB Lower Byte Read/Write Enable OEL OER Output Enable A0L - A10L A0R - A10R Address I/O0L - I/O15L I/O0R - I/O15R Data Input/Output BUSYL BUSYR Busy Flag VCC Power GND Ground 2746 tbl 01 3 6.42 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Maximum Operating Temperature and Supply Voltage(1,2) Absolute Maximum Ratings(1) Symbol VTERM(2) Rating Terminal Voltage with Respect to GND Commercial & Industrial Military Unit -0.5 to +7.0 -0.5 to +7.0 V Grade Military o Temperature Under Bias -55 to +125 Storage Temperature -65 to +150 PT(3) Power Dissipation 2.0 2.0 W IOUT DC Output Current 50 50 mA TBIAS TSTG -65 to +135 -55OC to +125OC 0V 5.0V + 10% 0V 5.0V + 10% 0V 5.0V + 10% O 0 C to +70 C O Output Capacitance -40 C to +85 C 2746 tbl 04 Recommended DC Operating Conditions Symbol Parameter VCC Supply Voltage GND Ground Input High Voltage Min. Typ. Max. Unit 4.5 5.0 5.5 V 0 0 0 V 2.2 ____ (1) Input Low Voltage (2) 6.0 ____ -0.5 0.8 V V 2746 tbl 05 Capacitance (TA = +25C, f = 1.0mhz) Conditions(2) Max. Unit VIN = 3dV 11 pF VOUT = 3dV 11 Input Capacitance O NOTES: 1. This is the parameter TA. This is the "instant on" case temperature. VIL Parameter(1) O C VIH COUT Vcc Industrial o -65 to +150 2746 tbl 02 CIN GND Commercial C NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VTERM must not exceed Vcc + 10% for more than 25% of the cycle time or 10ns maximum, and is limited to < 20mA for the period of VTERM > Vcc + 10%. Symbol Ambient Temperature NOTES: 1. VIL (min.) = -1.5V for pulse width less than 10ns. 2. VTERM must not exceed Vcc + 10%. pF 2746 tbl 03 NOTES: 1. This parameter is determined by device characterization but is not production tested. 2. 3dV references the interpolated capacitance when the input and output switch from 0V to 3V or from 3V to 0V. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (Either port, VCC = 5.0V 10%) 7133SA 7143SA Symbol Parameter Test Conditions Min. Max. Min. Max. Unit 10 ___ 5 A 10 ___ 5 A ___ 0.4 ___ 0.4 V IOL = 16mA ___ 0.5 ___ 0.5 V IOH = -4mA 2.4 ___ 2.4 ___ V (1) Input Leakage Current VCC = 5.5V, VIN = 0V to VCC ___ |ILO| Output Leakage Current CE = VIH, VOUT = 0V to VCC ___ VOL Output Low Voltage (I/O0-I/O15) IOL = 4mA VOL Open Drain Output Low Voltage (BUSY) VOH Output High Voltage |ILI| 7133LA 7143LA 2746 tbl 06 NOTE: 1. At Vcc < 2.0V, input leakages are undefined. 6.42 4 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges DC Electrical Characteristics Operating Temperature and Supply Voltage Range(2) (VCC = 5.0V 10%) 7133X20 7143X20 Com'l Only Symbol ICC ISB1 ISB2 ISB3 ISB4 Parameter Dynamic Operating Current (Both Ports Active) Standby Current (Both Ports - TTL Level Inputs) Standby Current (One Port - TTL Level Inputs) Full Standby Current (Both Ports CMOS Level Inputs) Full Standby Current (One Port CMOS Level Inputs) Test Condition f = fMAX 7133X35 7143X35 Com'l, Ind & Military Typ.(1) Max. Typ. (1) Max. Typ.(1) Max. Unit COM'L S L 250 230 310 280 250 230 300 270 240 210 295 250 mA MIL & IND S L ____ ____ ____ ____ 250 230 330 300 240 220 325 295 COM'L S L 25 25 80 70 25 25 80 70 25 25 70 60 MIL & IND S L ____ ____ ____ ____ 25 25 90 80 25 25 75 65 COM'L S L 140 120 200 180 140 100 200 170 120 100 180 160 MIL & IND S L ____ ____ ____ ____ 140 100 230 190 120 100 200 180 COM'L S L 1.0 0.2 15 5 1.0 0.2 15 4 1.0 0.2 15 4 MIL & IND S L ____ ____ ____ ____ 1.0 0.2 30 10 1.0 0.2 30 10 COM'L S L 140 120 190 170 140 120 190 170 120 100 170 150 MIL & IND S L ____ ____ ____ ____ 140 120 220 200 120 100 190 170 Version CE = VIL , Outputs Disabled 7133X25 7143X25 Com'l, Ind & Military (3) CEL and CER = VIH f = fMAX(3) CE"A" = VIL and CE"B" = VIH(4) f=fMAX(3) Active Port Outputs Disabled Both Ports CEL and CER > VCC - 0.2V VIN > VCC - 0.2V or VIN < 0.2V, f = 0(4) CE"A" < 0.2V and CE"B" > VCC - 0.2V(5) VIN > VCC - 0.2V or V IN < 0.2V Active Port Outputs Disabled f = fMAX(3) mA mA mA mA 2746 tbl 07a 7133X55 7143X55 Com'l, Ind & Military 7133X45 7143X45 Com'l & Military Symbol ICC ISB1 ISB2 ISB3 ISB4 Parameter Dynamic Operating Current (Both Ports Active) Standby Current (Both Ports - TTL Level Inputs) Standby Current (One Port - TTL Level Inputs) Full Standby Current (Both Ports CMOS Level Inputs) Full Standby Current (One Port CMOS Level Inputs) Test Condition Version CE = VIL , Outputs Disabled 7133X70/90 7143X70/90 Com'l & Military Typ. (1) Max. Typ. (1) Max. Typ. (1) Max. Unit mA COM'L S L 230 210 290 250 230 210 285 250 230 210 280 250 MIL & IND S L 230 210 320 290 230 210 315 285 230 210 310 280 COM'L S L 25 25 75 65 25 25 70 60 25 25 70 60 MIL & IND S L 25 25 80 70 25 25 80 70 25 25 75 65 COM'L S L 120 100 190 170 120 100 180 160 120 100 180 160 MIL & IND S L 120 100 210 190 120 100 210 190 120 100 200 180 Both Ports CEL and CER > VCC - 0.2V VIN > VCC - 0.2V or VIN < 0.2V, f = 0(4) COM'L S L 1.0 0.2 15 4 1.0 0.2 15 4 1.0 0.2 15 4 MIL & IND S L 1.0 0.2 30 10 1.0 0.2 30 10 1.0 0.2 30 10 CE"A" < 0.2V and CE"B" > VCC - 0.2V(5) VIN > VCC - 0.2V or V IN < 0.2V Active Port Outputs Disabled f = fMAX(3) COM'L S L 120 100 180 160 120 100 170 150 120 100 170 150 MIL & IND S L 120 100 200 180 120 100 200 180 120 100 190 170 f = fMAX(3) CEL and CER = VIH f = fMAX mA (3) CE"A" = VIL and CE"B" = VIH(4) f=fMAX(3) Active Port Outputs Disabled mA mA mA 2746 tbl 07b NOTES: 1. VCC = 5V, T A = +25C for Typ., and are not production tested. ICCDC = 180mA (typ.) 2. 'X' in part number indicates power rating (SA or LA) 3. At f = fMAX , address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/ tRC, and using "AC Test Conditions" of input levels of GND to 3V. 4. f = 0 means no address or control lines change. Applies only to inputs at CMOS level standby. 5. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 5 6.42 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Data Retention Characteristics (LA Version Only) VLC = 0.2V, VHC = VCC - 0.2V 7133LA/7143LA Symbol Parameter Test Condition Min. Typ. (1) Max. Unit 2.0 ___ ___ V A VDR VCC for Data Retention VCC = 2V ICCDR Data Retention Current CE > VHC MIL. & IND. ___ 100 4000 VIN > VHC or < VLC COM'L. ___ 100 1500 0 ___ ___ tRC(2) ___ ___ tCDR (3) Chip Deselect to Data Retention Time tR(3) Operation Recovery Time V V 2746 tbl 08 NOTES: 1. Vcc = 2V, TA = +25C, and are not production tested. 2. tRC = Read Cycle Time 3. This parameter is guaranteed by device characterization but is not production tested. Data Retention Waveform DATA RETENTION MODE VCC 4.5V VDR > 2V 4.5V tCDR tR VDR CE VIH VIH 2746 drw 05 AC Test Conditions 5V GND to 3.0V Input Pulse Levels 1250 5ns Max. Input Rise/Fall Times Input Timing Reference Levels 1.5V Output Reference Levels 1.5V DATAOUT 775 30pF Figures 1, 2 and 3 Output Load 2746 tbl 09 Figure 1. AC Output Test Load 5V 5V 270 1250 BUSY DATAOUT 775 5pF* 30pF 2746 drw 06 Figure 2. Output Load (for tLZ, t HZ, tWZ, tOW ) *Including scope and jig 6.42 6 Figure 3. BUSY Output Load (IDT7133 only) IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage(3) 7133X20 7143X20 Com'l Only Symbol Parameter 7133X25 7143X25 Com'l, Ind & Military 7133X35 7143X35 Com'l, Ind & Military Min. Max. Min. Max. Min. Max. Unit READ CYCLE tRC Read Cycle Time 20 ____ 25 ____ 35 ____ ns tAA Address Access Time ____ 20 ____ 25 ____ 35 ns tACE Chip Enable Access Time ____ 20 ____ 25 ____ 35 ns tAOE Output Enable Access Time ____ 12 ____ 15 ____ 20 ns tOH Output Hold from Address Change 0 ____ 0 ____ 0 ____ ns 0 ____ 0 ____ 0 ____ ns ____ 12 ____ 15 ____ 20 ns 0 ____ 0 ____ 0 ____ ns ____ 20 ____ 50 ____ 50 ns (1,2) tLZ Output Low-Z Time tHZ Output High-Z Time (1,2) tPU Chip Enable to Power Up Time (2) tPD Chip Disable to Power Down Time (2) 2746 tbl 10a 7133X55 7143X55 Com'l, Ind & Military 7133X45 7143X45 Com'l & Military Symbol Parameter 7133X70/90 7143X70/90 Com'l & Military Min. Max. Min. Max. Min. Max. Unit READ CYCLE tRC Read Cycle Time 45 ____ 55 ____ 70/90 ____ ns tAA Address Access Time ____ 45 ____ 55 ____ 70/90 ns tACE Chip Enable Access Time ____ 45 ____ 55 ____ 70/90 ns tAOE Output Enable Access Time ____ 25 ____ 30 ____ 40/40 ns tOH Output Hold from Address Change 0 ____ 0 ____ 0/0 ____ ns tLZ Output Low-Z Time (1,2) 0 ____ 5 ____ 5/5 ____ ns tHZ Output High-Z Time (1,2) ____ 20 ____ 20 ____ 25/25 ns tPU Chip Enable to Power Up Time (2) 0 ____ 0 ____ 0/0 ____ ns tPD Chip Disable to Power Down Time (2) ____ 50 ____ 50 ____ 50/50 ns NOTES: 1. Transition is measured 0mV fromLow or High-impedance voltage with load (Figure 2). 2. This parameter is guaranteed by device characterization, but is not production tested. 3. 'X' in part number indicates power rating (SA or LA). 7 6.42 2746 tbl 10b IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges TIMING WAVEFORM OF READ CYCLE NO. 1, EITHER SIDE(5) tRC ADDRESS tAA tOH DATAOUT tOH PREVIOUS DATA VALID DATA VALID BUSYOUT tBDD (3,4) 2746 drw 07 TIMING WAVEFORM OF READ CYCLE NO. 2, EITHER SIDE(5) tACE (4) CE tAOE (4) tHZ (2) OE tLZ DATAOUT tLZ tPU CURRENT (1) (1) tHZ (2) VALID DATA tPD ICC 50% 50% ISB 2746 drw 08 NOTES: 1. Timing depends on which signal is asserted last, OE or CE. 2. Timing depends on which signal is deasserted first, OE or CE. 3. tBDD delay is required only in a case where the opposite port is completing a write operation to the same address location. For simultaneous read operations, BUSY has no relationship to valid output data. 4. Start of valid data depends on which timing becomes effective last, t AOE, tACE, tAA, or tBDD. 5. R/W = VIH, and the address is valid prior to or coincidental with CE transition LOW. 6.42 8 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage(5) 7133X20 7143X20 Com'l Only Symbol Parameter 7133X25 7143X25 Com'l, Ind & Military 7133X35 7143X35 Com'l, Ind & Military Min. Max. Min. Max. Min. Max. Unit WRITE CYCLE tWC Write Cycle Time (3) 20 ____ 25 ____ 35 ____ ns tEW Chip Enable to End-of-Write 15 ____ 20 ____ 25 ____ ns tAW Address Valid to End-of-Write 15 ____ 20 ____ 25 ____ ns 0 ____ 0 ____ 0 ____ ns 15 ____ 20 ____ 25 ____ ns 0 ____ 0 ____ ns Address Set-up Time tAS Write Pulse Width tWP tWR Write Recovery Time 0 ____ tDW Data Valid to End-of-Write 15 ____ 15 ____ 20 ____ ns tHZ Output High-Z Time (1,2) ____ 12 ____ 15 ____ 20 ns tDH Data Hold Time (4) 0 ____ 0 ____ 0 ____ ns ____ 12 ____ 15 ____ 20 ns 0 ____ 0 ____ 0 ____ ns (1,2) Write Enable to Output in High-Z tWZ tOW Output Active from End-of-Write (1,2,4) 2746 tbl 11a 7133X45 7143X45 Com'l & Military Symbol Parameter 7133X55 7143X55 Com'l, Ind & Military 7133X70/90 7143X70/90 Com'l & Military Min. Max. Min. Max. Min. Max. Unit 45 ____ 55 ____ 70/90 ____ ns 30 ____ 40 ____ 50/50 ____ ns 40 ____ 50/50 ____ ns WRITE CYCLE tWC tEW Write Cycle Time (3) Chip Enable to End-of-Write tAW Address Valid to End-of-Write 30 ____ tAS Address Set-up Time 0 ____ 0 ____ 0/0 ____ ns tWP Write Pulse Width 30 ____ 40 ____ 50/50 ____ ns tWR Write Recovery Time 0 ____ 0 ____ 0/0 ____ ns 20 ____ 25 ____ 30/30 ____ ns ____ 20 ____ 20 ____ 25/25 ns 5 ____ 5 ____ 5/5 ____ ns ____ 20 ____ 20 ____ 25/25 ns 5 ____ 5 ____ 5/5 ____ ns tDW tHZ tDH Data Valid to End-of-Write Output High-Z Time Data Hold Time (1,2) (4) (1,2) tWZ Write Enable to Output in High-Z tOW Output Active from End-of-Write (1,2,4) 2746 tbl 11b NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage from the Output Test Load (Figure 2). 2. This parameter is guaranteed by device characterization but not production tested. 3. For MASTER/SLAVE combination, tWC = tBAA + tWR + tWP , since R/W = VIL must occur after tBAA. 4. The specification for tDH must be met by the device supplying write data to the RAM under all operation conditions. Although tDH and tOW values will very over voltage and temperature, the actual tDH will always be smaller than the actual t OW. 5. 'X' in part number indicates power rating (SA or LA). 9 6.42 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage(6) 7133X20 7143X20 Com'l Only Symbol Parameter 7133X25 7143X25 Com'l, Ind & Military 7133X35 7143X35 Com'l, Ind & Military Min. Max. Min. Max. Min. Max. Unit 20 ____ 20 ____ 30 ns 20 ____ 20 ____ 30 ns BUSY TIMING (For MASTER 71V33) tBAA BUSY Access Time from Address ____ tBDA BUSY Disable Time from Address ____ tBAC BUSY Access Time from Chip Enable ____ 20 ____ 20 ____ 25 ns tBDC BUSY Disable Time from Chip Enable ____ 17 ____ 20 ____ 25 ns tWDD Write Pulse to Data Delay(1) ____ 40 ____ 50 ____ 60 ns tDDD Write Data Valid to Read Data Delay tBDD BUSY Disable to Valid Data tAPS Arbitration Priority Set-up Time (3) tWH Write Hold After BUSY (1) ____ (2) (5) 30 ____ 35 ____ 45 ns ____ 25 ____ 30 ____ 35 ns 5 ____ 5 ____ 5 ____ ns 20 ____ 20 ____ 25 ____ ns 0 ____ 0 ____ 0 ____ ns ns ns BUSY INPUT TIMING (For SLAVE 71V43) tWB BUSY Input to Write (4) tWH Write Hold After BUSY 20 ____ 20 ____ 25 ____ tWDD Write Pulse to Data Delay(1) ____ 40 ____ 50 ____ 60 tDDD Write Data Valid to Read Data Delay (1) ____ 30 ____ 35 ____ 45 (5) ns 2746 tbl 12a 7133X45 7143X45 Com'l & Military Symbol Parameter 7133X55 7143X55 Com'l, Ind & Military 7133X70/90 7143X70/90 Com'l & Military Min. Max. Min. Max. Min. Max. Unit 40 ____ 40 ____ 45/45 ns BUSY TIMING (For MASTER 71V33) tBAA BUSY Access Time from Address ____ tBDA BUSY Disable Time from Address ____ 40 ____ 40 ____ 45/45 ns tBAC BUSY Access Time from Chip Enable ____ 30 ____ 35 ____ 35/35 ns tBDC BUSY Disable Time from Chip Enable ____ 25 ____ 30 ____ 30/30 ns tWDD Write Pulse to Data Delay (1) ____ tDDD Write Data Valid to Read Data Delay tBDD BUSY Disable to Valid Data(2) tAPS Arbitration Priority Set-up Time tWH Write Hold After BUSY (1) (3) (5) 80 ____ 80 ____ 90/90 ns ____ 55 ____ 55 ____ 70/70 ns ____ 40 ____ 40 ____ 40/40 ns 5 ____ 5 ____ 5/5 ____ ns 30 ____ 30 ____ 30/30 ____ ns 0 ____ 0 ____ 0/0 ____ ns ns ns BUSY INPUT TIMING (For SLAVE 71V43) tWB BUSY Input to Write (4) tWH Write Hold After BUSY 30 ____ 30 ____ 30/30 ____ tWDD Write Pulse to Data Delay(1) ____ 80 ____ 80 ____ 90/90 55 ____ 55 ____ 70/70 tDDD (5) Write Data Valid to Read Data Delay (1) ____ NOTES: 1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read and Busy". 2. tBDD is calculated parameter and is greater of 0, tWDD - tWP (actual) or tDDD - tDW (actual). 3. To ensure that the earlier of the two ports wins. 4. To ensure that the write cycle is inhibited on port "B" during contention on port "A". 5. To ensure that a write cycle is completed on port "B" after contention on port "A". 6. 'X' in part number indicates power rating (SA or LA). 6.42 10 ns 2746 tbl 12b IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Timing Waveform of Write Cycle No. 1 (R/W Controlled Timing)(1,5,8) tWC ADDRESS tAS OE (6) tWR(3) tAW CE tHZ tWP (2) R/W (7) (9) tWZ (7) tLZ DATAOUT tHZ (7) tOW (4) (4) tDH tDW DATAIN 2746 drw 09 Write Cycle No. 2 (CE Controlled Timing)(1,5) tWC ADDRESS tAW CE tAS(6) R/W tEW (2) tWR (9) tDW tDH DATAIN 2746 drw 10 NOTES: 1. R/W or CE must be HIGH during all address transitions. 2. A write occurs during the overlap (tEW or tWP) of a CE = VIL and a R/W = VIL. 3. tWR is measured from the earlier of CE or R/W going HIGH to the end of the write cycle. 4. During this period, the I/O pins are in the output state, and input signals must not be applied. 5. If the CE LOW transition occurs simultaneously with or after the R/W LOW transition, the outputs remain in the High-impedance state. 6. Timing depends on which enable signal (CE or R/W) is asserted last. 7. Timing depends on which enable signal is de-asserted first, CE or OE. 8. If OE is LOW during a R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data to be placed on the bus for the required tDW. If OE is HIGH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified tWP. 9. R/W for either upper or lower byte. 11 6.42 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Timing Waveform of Write with Port-to-Port Read and BUSY(1,2,3) tWC MATCH ADDR"A" tWP R/W"A" tDW tDH VALID DATAIN"A" (1) tAPS MATCH ADDR"B" tBDA tBDD BUSY"B" tWDD DATAOUT "B" VALID (4) tDDD 2746 drw 11 NOTES: 1. To ensure that the earlier of the two ports wins, t APS is ignored for Slave (IDT7143). 2. CEL = CER = VIL 3. OE = VIL for the reading port. 4. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port "A". Timing Waveform of Write with BUSY(3) tWP R/W"A" tWB BUSY"B" tWH R/W"B" (1) (2) , 2746 drw 12 NOTES: 1. tWH must be met for both BUSY input (IDT7143, slave) and output (IDT7133, master). 2. BUSY is asserted on port "B" blocking R/W"B", until BUSY "B" goes HIGH. 3. All timing is the same for left and right ports. Port " A" may be either left or right port. Port "B" is the opposite from port " A". 6.42 12 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Timing Waveform of BUSY Arbitration Controlled by CE Timing(1) ADDR"A" AND "B" ADDRESSES MATCH CE"A" tAPS(2) CE"B" tBAC tBDC BUSY"B" 2746 drw 13 Timing Waveform of BUSY Arbitration Controlled by Addresses(1) tRC OR ADDR "A" tWC ADDRESSES MATCH ADDRESSES DO NOT MATCH tAPS(2) ADDR "B" tBAA tBDA BUSY "B" 2746 drw 14 NOTES: 1. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port " A". 2. If tAPS is not satisfied, the BUSY will be asserted on one side or the other, but there is no guarantee on which side BUSY will be asserted (IDT7133 only). 13 6.42 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Functional Description The IDT7133/43 provides two ports with separate control, address and I/O pins that permit independent access for reads or writes to any location in memory. The IDT7133/43 has an automatic power down feature controlled by CE. The CE controls on-chip power down circuitry that permits the respective port to go into a standby mode when not selected (CE HIGH). When a port is enabled, access to the entire memory array is permitted. Non-contention READ/WRITE conditions are illustrated in Truth Table 1. LEFT RIGHT R/W R/W BUSY BUSY VCC R/W Width Expansion with Busy Logic Master/Slave Arrays When expanding an IDT7133/43 RAM array in width while using BUSY logic, one master part is used to decide which side of the RAM array will receive a BUSY indication, and to output that indication. Any number of slaves to be addressed in the same address range as the master, use the BUSY signal as a write inhibit signal. Thus on the IDT7133 RAM the BUSY pin is an output and on the IDT7143 RAM, the BUSY pin is an input (see Figure 3). BUSY R/W BUSY 270 Busy Logic Busy Logic provides a hardware indication that both ports of the RAM have accessed the same location at the same time. It also allows one of the two accesses to proceed and signals the other side that the RAM is "busy". The BUSY pin can then be used to stall the access until the operation on the other side is completed. If a write operation has been attempted from the side that receives a BUSY indication, the write signal is gated internally to prevent the write from proceeding. The use of BUSY logic is not required or desirable for all applications. In some cases it may be useful to logically OR the BUSY outputs together and use any BUSY indication as an interrupt source to flag the event of an illegal or illogical operation. If the write inhibit function of BUSY logic is not desirable, the BUSY logic can be disabled by using the IDT7143 (SLAVE). In the IDT7143, the BUSY pin operates solely as a write inhibit input pin. Normal operation can be programmed by tying the BUSY pins HIGH. If desired, unintended write operations can be prevented to a port by tying the BUSY pin for that port LOW. The BUSY outputs on the IDT 7133 RAM are open drain and require pullup resistors. IDT7133 MASTER R/W VCC IDT7143 SLAVE BUSY 270 R/W BUSY 2746 drw 15 Figure 4. Busy and chip enable routing for both width and depth expansion with the IDT7133 (MASTER) and the IDT7143 (SLAVE). Expanding the data bus width to 32 bits or more in a Dual-Port RAM system implies that several chips will be active at the same time. If each chip includes a hardware arbitrator, and the addresses for each chip arrive at the same time, it is possible that one will activate its BUSYL while another activates its BUSYR signal. Both sides are now BUSY and the CPUs will await indefinitely for their port to become free. To avoid the "Busy Lock-Out" problem, IDT has developed a MASTER/SLAVE approach where only one hardware arbitrator, in the MASTER, is used. The SLAVE has BUSY inputs which allow an interface to the MASTER with no external components and with a speed advantage over other systems. When expanding Dual-Port RAMs in width, the writing of the SLAVE RAMs must be delayed until after the BUSY input has settled. Otherwise, the SLAVE chip may begin a write cycle during a contention situation. Conversely, the write pulse must extend a hold time past BUSY to ensure that a write cycle takes place after the contention is resolved. This timing is inherent in all Dual-Port memory systems where more than one chip is active at the same time. The write pulse to the SLAVE should be delayed by the maximum arbitration time of the MASTER. If, then, a contention occurs, the write to the SLAVE will be inhibited due to BUSY from the MASTER. 6.42 14 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Truth Table I - Non-Contention Read/Write Control(4) LEFT OR RIGHT PORT(1) R/WLB R/WUB CE OE I/O0-7 I/O8-15 X X H X Z Z Port Disabled and in Power Down Mode, ISB2, ISB4 X X H X Z Z CER = CEL = VIH, Power Down Mode, ISB1 or ISB3 L L L X DATAIN DATAIN L H L L DATAIN DATAOUT H L L L DATAOUT DATAIN L H L H DATAIN Z Data on Lower Byte Written into Memory (2) H L L H Z DATAIN Data on Upper Byte Written into Memory (2) H H L L DATAOUT DATAOUT H H L H Z Z Function Data on Lower Byte and Upper Byte Written into Memory (2) Data on Lower Byte Written into Memory (2), Data in Memory Output on Upper Byte (3) Data in Memory Output on Lower Byte (3), Data on Upper Byte Written into Memory (2) Data in Memory Output on Lower Byte and Upper Byte High Impedance Outputs NOTES: 1. A0L - A10LA0R - A10R 2. If BUSY = LOW, data is not written. 3. If BUSY = LOW, data may not be valid, see tWDD and tDDD timing. 4. "H" = HIGH, "L" = LOW, "X" = Don't Care, "Z" = High-Impedance, "LB" = Lower Byte, "UB" = Upper Byte Truth Table II -- Address BUSY Arbitration Inputs Outputs CEL CER A0L-A10L A0R-A10R BUSYL(1) BUSYR(1) Function X X NO MATCH H H Normal H X MATCH H H Normal X H MATCH H H Normal L L MATCH (2) (2) Write Inhibit(3) 2746 tbl 14 NOTES: 1. Pins BUSY L and BUSYR are both outputs on the IDT7133 (MASTER). Both are inputs on the IDT7143 (SLAVE). On Slaves the BUSY input internally inhibits writes. 2. "L" if the inputs to the opposite port were stable prior to the address and enable inputs of this port. "H" if the inputs to the opposite port became stable after the address and enable inputs of this port. If tAPS is not met, either BUSYL or BUSYR = VIL will result BUSYL and BUSY R outputs can not be LOW simultaneously. 3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored when BUSYR outputs are driving LOW regardless of actual logic level on the pin. 15 6.42 2746 tbl 13 IDT7133SA/LA, IDT7143SA/LA High-Speed 2K x 16 Dual-Port RAM Military, Industrial and Commercial Temperature Ranges Ordering Information X XXXX XX XX X Device Type Power Speed Package X Process/ Temperature Range Blank I(1) B Commercial (0C to +70C) Industrial (-40C to +85C) Military (-55C to +125C) Compliant to MIL-PRF-38535 QML G(2) Green J G F PF 68-pin PLCC (J68-1) 68-pin PGA (GU68-1) 68-pin Flatplack (F68-1) 100-pin TQFP (PN100-1) 20 25 35 45 55 70 90 Commercial Only Commercial, Industrial & Military Commercial, Industrial & Military Commercial & Military Commercial, Industrial & Military Commercial & Military Commercial & Military LA SA Low Power Standard Power 7133 7143 32K (2K x 16-Bit) MASTER Dual-Port RAM 32K (2K x 16-Bit) SLAVE Dual-Port RAM Speed in nanoseconds 2746 drw 16a NOTES: 1. Contact your local sales office for industrial temp. range for other speeds, packages and powers. 2. Green parts available. For specific speeds, packages and powers contact your local sales office. Datasheet Document History 12/18/98: Page 2 02/17/99: 030/9/99: 06/09/99: 10/01/99: 11/10/99: 04/01/00: 06/26/00: 01/31/06: 10/21/08: Page 2 Page 4 Page 5 Page 1 Page 16 Page 16 Initiated datasheet document history Converted to new format Cosmetic and typographical corrections Added additional notes to pin configurations corrected PN100 pinout Corrected PF ordering code Cosmetic and typographical corrections Changed drawing format Added Industrial Temperature Ranges and removed corresponding notes Replaced IDT logo Changed 500mV to 0mV in notes Fixed overbar in pinout Increased storage temperature parameters Clarified TA parameter DC Electrical parameters-changed wording from "open" to "disabled" Added green availability to features Added green indicator for ordering information Removed "IDT" from orderable part number CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6.42 16 for Tech Support: 408-284-2794 DualPortHelp@idt.com