HMC552LP4 / 552LP4E v00.0306 MIXERS - SMT 7 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.6 - 3.0 GHz Typical Applications Features The HMC552LP4 / HMC552LP4E is ideal for Wireless Infrastructure Applications: Input IP3: +25 dBm * PCS / 3G Infrastructure LO to RF Isolation: 30 dB * Base Stations & Repeaters Low Conversion Loss: 8 dB * WiMAX & WiBro Single Positive Supply: +5V @ 62 mA * ISM & Fixed Wireless RoHS Compliant 4x4 mm QFN Package Functional Diagram General Description Low Input LO Drive: -4 to +4 dBm The HMC552LP4 & HMC552LP4E are high linearity, double-balanced converter ICs that operate from 1.6 to 3.0 GHz and deliver a +25 dBm input third order intercept point. The LO amplifier output and high dynamic range mixer input are positioned so that an external LO filter can be placed in series between them. The converter provides 30 dB of LO to RF isolation and is ideal for upconverter and downconverter applications. The IC operates from a single +5V supply consuming 62 mA of current and accepts a LO drive level of -4 to +4 dBm. The design requires no external baluns and supports IF frequencies between DC and 1 GHz. The HMC552LP4 & HMC552LP4E are pin for pin compatible with the HMC551LP4 & HMC551LP4E, which operate from 0.8 to 1.2 GHz. Electrical Specifications, TA = +25 C, LO = 0 dBm, Vcc = +5V, IF = 100 MHz* Parameter Min. Typ. Frequency Range, RF, LO 1.6 - 3.0 Frequency Range, IF DC - 1.0 Conversion Loss 8 Noise Figure (SSB) 8 Max. GHz GHz 10 dB dB LO to RF Isolation 25 30 dB LO to IF Isolation 10 20 dB IP3 (Input) 25 dBm 1 dB Compression (Input) 16 dBm -4 to +4 dBm 62 mA LO Drive Input Level (Typical) Supply Current (Icc) *Unless otherwise noted, all measurements performed as a downconverter configured as shown in application circuit. 7 - 414 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC552LP4 / 552LP4E v00.0306 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.6 - 3.0 GHz Conversion Gain vs. Temperature @ LO = 0 dBm Isolation @ LO = 0 dBm 0 -10 -5 -10 +25C +85C -40C -15 7 -20 -30 RF to IF LO to RF LO to IF -40 -20 -50 1 1.5 2 2.5 3 3.5 1 1.5 FREQUENCY (GHz) 0 -5 -5 -10 LO= -4 dBm LO= -2 dBm LO= 0 dBm LO= 2 dBm LO= 4 dBm -20 3 3.5 3 3.5 -10 RF LO -15 -20 1 1.5 2 2.5 3 3.5 1 1.5 FREQUENCY (GHz) 2 2.5 FREQUENCY (GHz) Upconverter Performance Conversion Gain vs. LO Drive IF Bandwidth @ LO = 0 dBm 0 0 -5 -5 RESPONSE (dB) CONVERSION GAIN (dB) 2.5 Return Loss @ LO = 0 dBm 0 RETURN LOSS (dB) CONVERSION GAIN (dB) Conversion Gain vs. LO Drive -15 2 FREQUENCY (GHz) MIXERS - SMT ISOLATION (dB) CONVERSION GAIN (dB) 0 -10 LO= -4 dBm LO= -2 dBm LO= 0 dBm LO= 2 dBm LO= 4 dBm -15 -10 -15 Conversion Gain Return Loss -20 -20 -25 1 1.5 2 2.5 FREQUENCY (GHz) 3 3.5 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 415 HMC552LP4 / 552LP4E v00.0306 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.6 - 3.0 GHz Input IP3 vs. LO Drive 35 30 30 INPUT IP3 (dBm) 35 25 20 +25C +85C -40C 15 10 5 1.5 25 20 15 LO= -4 dBm LO= -2 dBm LO= 0 dBm LO= 2 dBm LO= 4 dBm 10 2 2.5 3 5 1.5 3.5 2 2.5 FREQUENCY (GHz) 70 70 INPUT IP2 (dBm) 80 60 50 40 20 1.5 +25C +85C -40C 2 3 3.5 60 50 40 LO= -4 dBm LO= -2 dBm LO= 0 dBm LO= 2 dBm LO= 4 dBm 30 2.5 3.5 Input IP2 vs. LO Drive 80 30 3 FREQUENCY (GHz) Input IP2 vs. Temperature @ LO = 0 dBm INPUT IP2 (dBm) MIXERS - SMT 7 INPUT IP3 (dBm) Input IP3 vs. Temperature @ LO = 0 dBm 3 20 1.5 3.5 2 2.5 FREQUENCY (GHz) FREQUENCY (GHz) Input P1dB vs. Temperature @ LO = 0 dBm 20 19 INPUT P1dB (dBm) 18 17 16 15 14 13 +25C +85C -40C 12 11 10 1.5 1.8 2 2.2 2.5 2.7 3 FREQUENCY (GHz) 7 - 416 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC552LP4 / 552LP4E v00.0306 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.6 - 3.0 GHz MxN Spurious @ IF Port Harmonics of LO 2 nLO Spur @ RF Port 0 1 0 xx -3 16 1 7 0 23 2 79 66 61 61 3 102 105 93 4 103 107 107 RF Freq. = 1.9 GHz @ -10 dBm LO Freq. = 1.8 GHz @ 0 dBm All values in dBc relative to the IF power level. 3 4 LO Freq. (GHz) 1 2 3 16 25 1.5 27 17 31 32 44 53 1.8 28 16 40 44 98 2.1 28 18 31 47 94 84 2.4 34 21 33 41 102 103 2.7 36 28 42 46 3.0 41 27 48 54 LO = 0 dBm All values in dBc below input LO level measured at RF port. Typical Supply Current Vcc Icc (mA) +5.0 62 mA For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 4 7 MIXERS - SMT nLO mRF 7 - 417 HMC552LP4 / 552LP4E v00.0306 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.6 - 3.0 GHz Absolute Maximum Ratings MIXERS - SMT 7 RF / IF Input (Vcc= +5V) +31 dBm LO Drive (Vcc= +5V) +10 dBm BIAS +7 Vdc Junction Temperature 150C Continuous Pdiss (T = 85C) (derate 9.5 mW/C above 85C) 0.6 W Thermal Resistance (junction to ground paddle) 105.6 C/W Storage Temperature -65 to +150C Operating Temperature -40 to +85C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC552LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC552LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H552 XXXX [2] H552 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX 7 - 418 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC552LP4 / 552LP4E v00.0306 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.6 - 3.0 GHz Pin Descriptions Function Description 1 MIX LO This pin is DC coupled and matched to 50 Ohms from 1.6 to 3.0 GHz. An off chip DC blocking capacitor is required. 2, 6 - 9, 11 - 17, 19 - 24 N/C No connection. These pins may be connected to RF ground. Performance will not be affected. 3 BIAS Power supply for the second stage LO amplifier. Three external bypass capacitors are recommended for optimum performance, as illustrated in the application circuit. 4 GND Backside of package has exposed metal ground paddle that must also be connected to ground. 5 LO This pin is DC coupled and matched to 50 Ohms from 1.6 to 3.0 GHz. An off chip DC blocking capacitor is required. 10 IF This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC, this pin must not source/sink more than 18 mA of current or die non-function and possible die failure will result. 18 RF This pin is DC coupled and matched to 50 Ohms from 1.6 to 3.0 GHz. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 MIXERS - SMT Pin Number 7 - 419 HMC552LP4 / 552LP4E v00.0306 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.6 - 3.0 GHz Evaluation PCB MIXERS - SMT 7 List of Materials for Evaluation PCB 113722 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4, J5 DC Pin C1, C2, C5 100 pF Chip Capacitor, 0402 Pkg. C3 1000 pF Chip Capacitor, 0603 Pkg. C4 2.2 F Capacitor, Tantalum L1 18 nH Chip Inductor, 0603 Pkg. R1 18 Ohm Resistor, 1210 1/8 watt Pkg. U1 HMC552LP4 / HMC552LP4E PCB [2] 113417 Evaluation Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 7 - 420 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC552LP4 / 552LP4E v00.0306 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.6 - 3.0 GHz Application Circuit MIXERS - SMT 7 Recommended Components Values (IF = DC - 300 MHz) C3 1000 pF C4 2.2 F C1, C2, C5 100 pF L1 18 nH R1 18 Ohm For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 421