ADP1764-1.0-EVALZ - ANALOG DEVICES

ADP1764-EVALZ/ADP1765-EVALZ User Guide

UG-1072

One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com

Evaluating the ADP1764 and ADP1765 Low VIN, Low Noise, CMOS Linear Regulators

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT

WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 9

FEATURES

Full featured evaluation boards for ADP1764 and ADP1765

Input voltage range: 1.10 V to 1.98 V

Output current range:

ADP1764: 0 mA to 4 A

ADP1765: 0 mA to 5 A

Evaluation available on adjustable or fixed output voltage

Convenient test points for electrical measurements

Operating temperature range: −40°C to +125°C

ADDITIONAL EQUIPMENT NEEDED

Voltage source

Voltmeter

Ammeter

Electronic resistor load

GENERAL DESCRIPTION

The ADP1764-1.0-EVALZ and ADP1765-1.0-EVALZ fixed

evaluation boards and the ADP1764-ADJ-EVALZ and ADP1765-

ADJ-EVALZ adjustable evaluation boards demonstrate the

functionality of the ADP1764 and the ADP1765 series of linear

regulators.

Simple device measurements, such as line and load regulation,

dropout voltage, and ground current, are demonstrated with

only a single voltage supply, a voltmeter, an ammeter, and load

resistors.

Figure 1 and Figure 2 show the ADP1765 evaluation boards;

the ADP1764 fixed and adjustable evaluation boards are

identical to the ADP1765.

For full details on the ADP1764 and the ADP1765 linear

regulators, see the ADP1764 and the ADP1765 data sheets, which

should be consulted in conjunction with this user guide when using

these evaluation boards.

EVALUATION BOARD PHOTOGRAPHS

15194-001

Figure 1. The ADP1765-1.0-EVALZ Fixed Board

(Identical to the ADP1764-1.0-EVALZ)

15194-002

Figure 2. The ADP1765-ADJ-EVALZ Adjustable Board

(Identical to the ADP1764-ADJ-EVALZ)

UG-1072 ADP1764-EVALZ/ADP1765-EVALZ User Guide

Rev. 0 | Page 2 of 9

TABLE OF CONTENTS

Features .............................................................................................. 1

General Description ......................................................................... 1

Evaluation Board Photographs ....................................................... 1

Revision History ............................................................................... 2

Evaluation Board Hardware ............................................................ 3

Evaluation Board Configurations .............................................. 3

Output Voltage Measurements ................................................... 4

Line Regulation Measurements .................................................. 5

Load Regulation Measurements ..................................................5

Dropout Voltage Measurements..................................................5

Ground Current Measurements ..................................................5

Ground Current Consumption ...................................................6

Evaluation Board Schematics and Artwork ...................................7

Ordering Information .......................................................................9

Bill of Materials ..............................................................................9

REVISION HISTORY

1/2017—Revision 0: Initial Version

ADP1764-EVALZ/ADP1765-EVALZ User Guide UG-1072

Rev. 0 | Page 3 of 9

EVALUATION BOARD HARDWARE

EVALUATION BOARD CONFIGURATIONS

The ADP1764 and ADP1765 evaluation boards come supplied

with different components, depending on the adjustable or fixed

version ordered. Components common to all versions are C1,

C2, C3, C4, C5, J1, and R2. Use R1 for the ADP1764-ADJ-E VA L Z

and ADP1765-ADJ-E VA L Z evaluation boards. Figure 9 and

Figure 10 show the schematics of these evaluation board

configurations, and Table 1 describes the hardware components.

The ADP1764-ADJ-E VA L Z and ADP1765-ADJ-E VA L Z have

an output voltage range of 0.5 V to 1.5 V. The output voltage is

set to 1.0 V by the external 6.8 kΩ adjust resistor.

Calculate the output voltage (VOUT) by

VOUT = AD × (RADJ × IADJ)

where:

AD is the gain factor with a typical value of 2.99 between the

VADJ pin and VOUT pin.

RADJ is the resistor connected between the VADJ pin and

ground.

IADJ is the 50 µA constant current from the VADJ pin.

The ADP1764-1.0-E VA L Z and ADP1765-1.0-E VA L Z fixed

evaluation boards use a 1.0 V output model. Do not connect R1

for the fixed output option.

Calculate the start-up time of the regulator by

tSTART-UP_FIXED = tDELAY + VREF × (CSS/ISS)

tSTART-UP_ADJ = tDELAY + VADJ × (CSS/ISS)

where:

tD E L AY is a fixed delay of 100 µs.

VREF is a 0.5 V internal reference for the fixed output model option.

CSS is the soft start capacitance from the SS pin to GND.

ISS is the current sourced from the SS pin (10 µA).

VADJ is the voltage at the VADJ pin equal to RADJ × IADJ.

Table 1. Evaluation Board Hardware Components

Component Description

U1 ADP1764 and ADP1765 low dropout linear

regulators.

For the fixed output option, U1 uses the 1.0 V

output option of the ADP1764 and the ADP1765.

For the adjustable output option, U1 uses the

adjustable option of the ADP1764 and the

ADP1765 and is set to 1.0 V.

C1 Input bypass capacitor (CIN), 22 µF, 0603 size.

C2 Output capacitor (COUT), 22 µF, 0603 size.

C3 Soft start capacitor (CSS), 1000 pF, 0603 size.

(not installed in the evaluation board)

Regulator capacitor (C

REG

), 1 µF, 0603 size.

C5 Reference capacitor (CREG), 1 µF, 0603 size.

J1 Jumper (connects EN to VIN for automatic startup)

R1 Adjust resistor (RADJ) used to set the output

voltage of the adjustable version of the ADP1764

and the ADP1765.

R2 Pull-up resistor (RPULL-UP) used for the open-drain

PG output pin.

UG-1072 ADP1764-EVALZ/ADP1765-EVALZ User Guide

Rev. 0 | Page 4 of 9

OUTPUT VOLTAGE MEASUREMENTS

1.29999

+ –

VOLTMETER

+ –

VOLTAGE

SOURCE

LOAD

15194-003

Figure 3. Output Voltage Measurement Setup

Figure 3 shows how the evaluation boards can be connected to a

voltage source and a voltmeter for basic output voltage accuracy

measurements.

A resistor can be used as the load for the regulator. Ensure that

the resistor has a power rating that is adequate to handle the

power expected to dissipate across it. Use an electronic load as

an alternative. Ensure the voltage source can supply enough

current for the expected load levels.

Follow these steps to connect the evaluation board to a voltage

source and voltmeter:

1. Connect the negative terminal of the voltage source to one

of the GND pads on the evaluation board.

2. Connect the positive terminal of the voltage source to the

VIN pad on the evaluation board.

3. Connect a load between the VOUT pad and one of the

GND pads on the evaluation board.

4. Connect the negative terminal of the voltmeter to one of

the GND pads on the evaluation board.

5. Connect the positive terminal of the voltmeter to the

VOUT pad on the evaluation board.

When these steps are completed, the voltage source can be turned

on. If J1 is inserted (connecting EN to VIN for automatic startup),

the regulator powers up.

If the load current is large, the user must connect the voltmeter

as close as possible to the output capacitor to reduce the effects

of ohmic voltage drops (IR).

ADP1764-EVALZ/ADP1765-EVALZ User Guide UG-1072

Rev. 0 | Page 5 of 9

LINE REGULATION MEASUREMENTS

For line regulation measurements, the change in the output of

the regulator is measured when the input is varied. For good

line regulation, the output must change as little as possible with

varying input levels. To ensure that the device is not in dropout

mode during line regulation measurement, VIN must be varied

between VOUT + 0.2 V (or 1.1 V, whichever is greater) and 1.98 V.

For example, for an ADP1764 or an ADP1765 device with a fixed

1.3 V output, VIN must be varied between 1.5 V and 1.98 V. This

measurement can be repeated under different load conditions.

Figure 4 shows the typical line regulation performance of an

ADP1764 and an ADP1765 with a fixed 1.3 V output.

1.296

1.297

1.298

1.299

1.300

1.301

1.302

1.303

1.304

1.305

1.306

1.50 1.58 1.66 1.74 1.82 1.90 1.98

VOUT (V)

VIN (V)

ILOAD = 0.1A

ILOAD = 1.0A

ILOAD = 2.0A

ILOAD = 3.0A

ILOAD = 4.0A

ILOAD = 5.0A

15194-004

Figure 4. Output Voltage vs. Input Voltage at VOUT = 1.3 V, TA = 25°C

LOAD REGULATION MEASUREMENTS

For load regulation measurements, the output of the regulator is

monitored while the load is varied. For good load regulation,

the output must change as little as possible with varying load.

The input voltage must be held constant during load regulation

measurement. The load current can be varied from 0 mA to 4 A

for the ADP1764 and 0 mA to 5 A for the ADP1765. Figure 5

shows the typical load regulation performance of an ADP1764

and an ADP1765 with a fixed 1.3 V output for an input voltage

of 1.5 V.

1.296

1.297

1.298

1.299

1.300

1.301

1.302

1.303

1.304

0.1 110

OUT

(V)

LOAD CURRENT ( A)

15194-005

Figure 5. Output Voltage vs. Load Current at VIN = 1.5 V, VOUT = 1.3 V, TA = 25°C

DROPOUT VOLTAGE MEASUREMENTS

The dropout voltage can be measured using the configuration

shown in Figure 3. Dropout voltage is defined as the input to

output voltage differential when the input voltage is set to the

nominal output voltage. The ADP1764 and the ADP1765 only

enter dropout mode for output voltages of at least 1.2 V. For

lower voltage outputs, the ADP1764 and the ADP1765 enter

undervoltage lockout and shut down. The dropout voltage

increases with larger loads.

For accurate measurements, use a second voltmeter to monitor

the input voltage across the input capacitor. The input supply

voltage may need adjusting to account for IR drops, especially

when using large load currents. Figure 6 shows the typical curve

of dropout voltage measurements with different load currents.

0.01

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.1 110

VDROP (V)

LO AD CURRE NT (A)

15194-006

Figure 6. Dropout Voltage vs. Load Current, VOUT = 1.3 V, TA = 25°C

GROUND CURRENT MEASUREMENTS

Figure 8 shows how the ADP1764 and ADP1765 evaluation

boards can connect to a voltage source and an ammeter for

ground current measurements.

A resistor can be used as the load for the regulator. Ensure the

resistor has a power rating that is adequate to handle the power

expected to be dissipated across it. Use an electronic load as an

alternative. Ensure that the voltage source can supply enough

current for the expected load levels.

Follow these steps to connect the evaluation board to a voltage

source and ammeter:

1. Connect the positive terminal of the voltage source to the

VIN pad on the evaluation board.

2. Connect the positive terminal of the ammeter to one of the

GND pads on the evaluation board.

3. Connect the negative terminal of the ammeter to the

negative terminal of the voltage source.

4. Connect a load between the VOUT pad on the evaluation

board and the negative terminal of the voltage source.

When these connection steps are completed, the voltage source

can be turned on. If J1 is inserted (connecting EN to VIN for

automatic startup), the regulator powers up.

UG-1072 ADP1764-EVALZ/ADP1765-EVALZ User Guide

Rev. 0 | Page 6 of 9

GROUND CURRENT CONSUMPTION

Ground current measurements can determine how much current

the internal circuits of the regulator consume while the circuits

perform the regulation function. To be efficient, the regulator

must consume as little current as possible. Typically, the regulator

uses the maximum current when supplying its largest load level

(4 A for the ADP1764 and 5 A for the ADP1765). Figure 7 shows

the typical ground current consumption for various load levels at

VOUT = 1.3 V and TA = 25°C.

When the device is disabled (EN = GND), the ground current

drops to less than 2 µA.

1.5 1.6 1.7 1.8 1.9 2.0

IGND ( mA)

VIN (V)

ILOAD = 0.1A

ILOAD = 1.0A

ILOAD = 2.0A

ILOAD = 3.0A

ILOAD = 4.0A

ILOAD = 5.0A

15194-007

Figure 7. Ground Current vs. Input Voltage, VOUT = 1.3 V, TA = 25°C

0.012345

+–

AMMETER

+–

LOAD

VOLTAGE

SOURCE

15194-008

Figure 8. Ground Current Measurement Setup

ADP1764-EVALZ/ADP1765-EVALZ User Guide UG-1072

Rev. 0 | Page 7 of 9

EVALUATION BOARD SCHEMATICS AND ARTWORK

15194-009

Figure 9. Fixed Output Schematic

15194-010

Figure 10. Adjustable Output Schematic

UG-1072 ADP1764-EVALZ/ADP1765-EVALZ User Guide

Rev. 0 | Page 8 of 9

15194-011

Figure 11. Top Layer

15194-012

Figure 12. Bottom Layer

ADP1764-EVALZ/ADP1765-EVALZ User Guide UG-1072

Rev. 0 | Page 9 of 9

ORDERING INFORMATION

BILL OF MATERIALS

Table 2.

Reference

Designator Description Manufacturer Part Number

C1, C2 Capacitors, MLCC, 22 μF, 10 V, 0603, X5R Murata (or equivalent) GRM188R61A226ME15D

C31 Capacitor, MLCC, 1000 pF, 100 V, 0603, X7R Murata (or equivalent) GRM188R72A102KA01D

C4, C5 Capacitors, MLCC, 1 μF, 10 V, 0603, X7R Murata (or equivalent) GRM188R71A105KA61D

J1 Header/jumper, single, STR, two pins FCI 69157-102HLF

R1 Resistor, 0603, 6.8 kΩ, 1% tolerance (do not install on the fixed model) Any manufacturer Depends on manufacturer

R2 Resistor, 0603, 100 kΩ, 1% tolerance Any manufacturer Depends on manufacturer

U1 IC, low input, low dropout regulators, including the following devices: Analog Devices, Inc. ADP1764ACPZ-1.0-R7

ADP1765ACPZ-1.0-R7

ADP1764ACPZ-R7

ADP1765ACPZ-R7

1 Not installed in the evaluation board.

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions

set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you

have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.

(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,

temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided

for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional

limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term

“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including

ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may

not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to

promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any

occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.

Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice

to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO

WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED

TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL

PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF

THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE

AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable

United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of

Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby

submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

registered trademarks are the property of their respective owners.

UG15194-0-1/17(0)