Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals Hand Crimp Tool Application Tooling Specification Sheet TYPE 4D Order No. 63819-1300 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position Right and Left handed applications Dies and Locator from this tool can be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V), with the use of the 63816-0800 Crimp Head Many different tool kits can be used with a single Battery Powered Crimp Tool This tool is RoHS compliant, however RoHS compliant is not required SCOPE Products: 1.57mm (.062") Diameter, Standard .062" Pin and Socket Crimp Terminals, 18-24 AWG. Terminal Series No. 1560 1561 1786 1787 5005 5006 Terminal Order No. Wire Size Insulation Diameter Loose Piece Reel AWG mm mm In. 02-06-2103 02-06-6119 02-06-2101 02-06-6118 02-06-6102 04-01-0805 02-06-6100 39-00-0278 02-06-6103 39-00-0327 02-06-6101 39-00-0328 18-24 N/A 1.52-3.05 .060-.120 02-06-6104 39-00-0330 02-06-6105 39-00-0329 02-06-6112 02-06-6116 02-06-1103 04-01-0808 02-06-1101 04-01-0806 02-06-5102 39-00-0331 02-06-1118 39-00-0279 02-06-5103 39-00-0334 02-06-5100 39-00-0332 18-24 N/A 1.52-3.05 .060-.120 02-06-5104 02-06-5101 39-00-0333 02-06-5109 02-06-5108 02-06-2202 02-06-6202 02-06-2201 02-06-6201 18-24 N/A 1.52-3.05 .060-.120 02-06-1202 02-06-1201 02-06-5205 18-24 N/A 1.52-3.05 .060-.120 02-06-5201 08-70-0042 08-70-1012 08-70-0001 08-70-1011 18-24 N/A 1.30-3.00 .051-.118 08-70-0043 08-70-1014 08-70-0002 08-70-1013 18-24 N/A 1.30-3.00 .051-.118 Customer to cut off terminal from reel: 0.13mm (.005") maximum Cut-off Tab. Doc No: ATS-638191300 Revision: G Release Date: 01-22-08 Revision Date: 05-05-16 UNCONTROLLED COPY Strip Length mm In. 2.41-3.04 .095-.120 2.41-3.04 .095-.120 2.41-3.04 .095-.120 2.41-3.04 .095-.120 2.30-2.95 .090-.116 2.30-2.95 .090-.116 Page 1 of 9 Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals DEFINITION OF TERMS BRUSH BEND UP BELL MOUTH CONDUCTOR CRIMP INSULATION CRIMP SEE NOTE ROLLING TWISTING STRIP LENGTH BEND DOWN CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Tool Qualification Notes: 1. Pull Force should be measured with no influence from the insulation crimp. 2. The above specifications are guidelines to an optimum crimp. CRIMP SPECIFICATIONS After crimping, the crimped terminals should measure as follows: Terminal Series No 1560 1561 1786 1787 5005 5006 Doc No: ATS-638191300 Revision: G Wire Size AWG mm2 18 20 N/A 22 24 18 20 N/A 22 24 18 20 N/A 22 24 18 20 N/A 22 24 18 20 N/A 22 24 18 20 N/A 22 24 Conductor Crimp Insulation Crimp Height (Ref.) Width (Ref.) Height (Ref.) Width (Ref.) mm In. mm In. mm In. mm In. 0.87-0.97 .034-.038 1.66 .065 2.62 .103 2.47 .097 0.85-0.95 .033-.037 1.65 .065 2.60 .102 2.46 .096 0.82-0.92 .032-.036 1.50 .059 2.20 .087 2.23 .088 0.77-0.87 .030-.034 1.50 .059 2.12 .083 2.20 .087 0.87-0.97 .034-.038 1.66 .065 2.62 .103 2.47 .097 0.85-0.95 .033-.037 1.65 .065 2.60 .102 2.46 .096 0.82-0.92 .032-.036 1.50 .059 2.20 .087 2.23 .088 0.77-0.87 .030-.034 1.50 .059 2.12 .083 2.20 .087 0.87-0.97 .034-.038 1.66 .065 2.62 .103 2.47 .097 0.85-0.95 .033-.037 1.65 .065 2.60 .102 2.46 .096 0.82-0.92 .032-.036 1.50 .059 2.20 .087 2.23 .088 0.77-0.87 .030-.034 1.50 .059 2.12 .083 2.20 .087 0.87-0.97 .034-.038 1.66 .065 2.62 .103 2.47 .097 0.85-0.95 .033-.037 1.65 .065 2.60 .102 2.46 .096 0.82-0.92 .032-.036 1.50 .059 2.20 .087 2.23 .088 0.77-0.87 .030-.034 1.50 .059 2.12 .083 2.20 .087 0.94-1.04 .037-.041 1.68 .066 2.65 .104 2.54 1.00 0.91-1.01 .036-.040 1.67 .065 2.58 .102 2.48 .098 0.86-0.96 .034-.038 1.53 .060 2.27 .089 2.29 .090 0.84-0.94 .033-.037 1.52 .059 2.20 .079 2.22 .087 0.94-1.04 .037-.041 1.68 .066 2.65 .104 2.54 1.00 0.91-1.01 .036-.040 1.67 .065 2.58 .102 2.48 .098 0.86-0.96 .034-.038 1.53 .060 2.27 .089 2.29 .090 0.84-0.94 .033-.037 1.52 .059 2.20 .079 2.22 .087 Release Date: 01-22-08 Revision Date: 05-05-16 UNCONTROLLED COPY Page 2 of 9 Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals Note: The crimp height chart is provided with this document as Reference Only. Due to the wide range of wires, strands, insulation diameters, and insulation hardness, actual crimp height measurements may very slightly. An occasional, destructive, pull force test should be performed to check crimp integrity. Pull Force measurement must exceed the minimum pull force specification. Terminal Series No 1560 1561 1786 1787 5005 5006 Wire Size Pull Force Minimum Profile AWG mm2 N Lb. 18-20 22-24 18 0.82 89 20 X 20 0.52 66.8 15 X 22 0.32 44.5 10 X 24 0.20 35.6 8 X 18 0.82 89 20 X 20 0.52 66.8 15 X 22 0.32 44.5 10 X 24 0.20 35.6 8 X 18 0.82 89 20 X 20 0.52 66.8 15 X 22 0.32 44.5 10 X 24 0.20 35.6 8 X 18 0.82 89 20 X 20 0.52 66.8 15 X 22 0.32 44.5 10 X 24 0.20 35.6 8 X 18 0.82 98 22 X 20 0.52 66.8 15 X 22 0.32 53.4 12 X 24 0.20 35.6 8 X 18 0.82 98 22 X 20 0.52 66.8 15 X 22 0.32 53.4 12 X 24 0.20 35.6 8 X Tool Qualification Notes: 1. Pull Force should be measured with no influence from the insulation crimp. 2. The above specifications are guidelines to an optimum crimp. Insulation Crimp Note: Due to the terminal's insulation grip design and/or insulation diameter range, this tool uses "overlap" form geometry in the insulation punch. This produces an overlap insulation crimp. While the insulation punch profile may appear "lopsided", this is a normal condition for this tool. See figure below. PUNCH OVERLAP FORM GEOMETRY OVERLAP INSULATION CRIMP ANVIL Doc No: ATS-638191300 Revision: G Release Date: 01-22-08 Revision Date: 05-05-16 UNCONTROLLED COPY WIRE Page 3 of 9 Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals Insulation Crimp Quality Crimping small insulation diameter wire in the 22-24AWG profile may cause a buckled insulation crimp. This is because the smaller insulation does not provide enough support to prevent the insulation grips from buckling while they are trying to overlap form. The buckled insulation crimp can be prevented by using a larger insulation diameter wire. For example, the insulation crimps shown below are on a 24AWG wire. The UL1007 insulation does not provide enough support and the insulation grips buckle. The larger UL1015 insulation provides better grip support and the grips overlap. 24AWG UL1007: GRIPS BUCKLE 24AWG UL1015: GRIPS OVERLAP In general, buckling can be prevented in the 22-24AWG profile by using an insulation diameter that is at least 1.6mm (0.063 in). If small insulation diameter must be used, insulation grip buckling is acceptable provided that the insulation crimp does not damage the wire's conductor and the crimped terminal fits into the connector housing. HANDLE WILL SPRING OPEN OPERATION CAUTION: Crimp only the Molex terminals listed in the scope for this tool. Do not crimp hardened objects as damage can occur to the tool frame and/or crimp dies. Open the tool by squeezing the handles together. At the end of the closing stroke, the ratchet mechanism will release the handles and the hand tool will spring open. See Figure 1. SQUEEZE HANDLES TOGETHER Figure 1 Crimping Terminals 1. Select the desired terminal from the chart, and install the proper locator (See chart above and Locator Installation on page 5). 2. Make sure the center of the locator is in the down position. With the locator attached, push the locator button on the back of the hand tool to bring the locator forward through the tooling. See Figure 2. 3. While holding in the locator button, load the terminal into the proper nest opening in the locator, based on the wire gauge or terminal type markings on the hand tooling. See Figure 3. Doc No: ATS-638191300 Revision: G Release Date: 01-22-08 Revision Date: 05-05-16 UNCONTROLLED COPY Page 4 of 9 Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals LOCATOR IN DOWN POSTION TERMINAL LOCATOR PUSHED THRU TOOLING RELEASE LOCATOR BUTTON LOCATOR BUTTON PUSHED IN Figure 2 PUSH ON THE LOCATOR BUTTON Figure 3 TERMINAL 4. Release the locator button, allowing the locator to return to the crimping position. 5. Close the tool handle until the first ratchet position engages. See Figure 4. 6. Insert the properly stripped wire through the terminal and against the wire stop. See Figure 5. 7. Crimp the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed. Release the handles to open the jaws. TERMINAL PRE-STRIPPED WIRE TOOLING PARTIALLY CLOSED PARTIALLY CLOSE HANDLE OPEN POSITION WIREFIRST STOPRATCHET IS PART OFPOSITION THE LOCATOR Figure 4 WIRE AGAINST THE WIRE STOP Figure 5 TERMINAL WIRE Note: The tamper proof ratchet action will not release the tool until it has been fully closed. 8. Remove the crimped terminal from the terminal locator by pulling on the wire. 9. Visually inspect the crimped terminal for proper crimp location. 10. On some large O.D. wires, it may not be possible to insert the wire with the tool partially closed. Those wires should be inserted with the hand tool in the open position. Insert the wire above the terminal in the punch and against the wire stop then close the tool. See Figure 6. Doc No: ATS-638191300 Revision: G Release Date: 01-22-08 Revision Date: 05-05-16 TERMINAL UNCONTROLLED COPY Page 5 of 9 Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals Locator Replacement See the parts list on the last page of this document for the proper locator order number. Follow the steps below to replace the locator. LOCATOR SQUEEZE HERE MAKE SURE CENTER OF LOCATOR IS IN THE DOWN POSITION TOP SLOTS OF HANDTOOL SQUEEZE HERE JAWS OPEN TOOLING PULL OPEN TOOLING M3 BHCS TOP HOOKS Figure 8 PUSH ON HANDLE Figure 7B Figure 7A LOWER TABS 1. Open the crimp hand tool. 2. Squeeze gently on the lower area shown in Figure 7A with your thumb and index finger. The lower tabs of the locator should disengage from the hand tool. 3. Lift and pull away from the hand tool. The top locator hooks should slip out of the top slots easily. See Figure 7A. 4. To reinstall the new locator, make sure the hand tool is in the open position. 5. Press the red insert down as far as it will go as shown in Figure 7B. 6. Holding onto the lower part of the locator with your thumb and index finger, insert the locator top hooks (2) into the hand tool top slots. 7. Rotate the locator down and press the lower tabs into the two bottom slots of the hand tool. To secure the locator into place, the lower tabs must snap into place on the hand tool frame. Right or Left Hand Operation This hand tool has an added feature that can be converted from a right handed application to a left handed application. It is necessary to reverse the tooling along with the locator if using the left handed application. Follow the steps below: 1. The locator must be removed before reversing the tooling. 2. Remove the M3 screw that holds the upper tooling. Doc No: ATS-638191300 Revision: G Release Date: 01-22-08 Revision Date: 05-05-16 MATCH UP MARKS Figure 9 FRONT UNCONTROLLED COPY BACK Page 6 of 9 Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals 3. Flip the upper tooling to the opposite side and replace the M3 screw. Make sure the small markings on the front and back of the hand tool frame match up and are on the outside of the hand tool frame. See Figure 8 and 9. 4. Reverse the lower tooling and tighten the M3 screw. Be sure the small markings line up. 5. Reinstall the locator by following the Instructions in the locator replacement section. Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: LUBRICATION POINTS (BOTH SIDES) LIGHT OIL (EVERY 3 MONTHS OR 5,000 CRIMPS) 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, Figure 10 lint free cloth. 2. Do not use any abrasive materials that could damage the tool. 3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life. 4. Wipe excess oil from hand tool, particularly from crimping area. Oil RATCHET RELEASE transferred from the crimping area onto certain terminations may affect the LEVER electrical characteristics of an application. 5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a clean, dry area. Miscrimps or Jams Should this tool ever become stuck or jammed in a partially closed position, Do not force the handles open or closed. The tool will open easily by pressing up on the ratchet release lever in the movable handle. See Figure 11. How to Adjust Tool Preload (See Figure 12) This hand tool is factory preset to 25-45 pounds. preload. It may be necessary over the life of the tool to adjust tool handle preload force. Listed below are the steps required to adjust the crimping force of the hand tool to obtain proper crimp conditions: 1. Hold the hand tool in the palm of your hand as shown in Figure 12. Using the index finger squeeze the link towards the top of the hand tool frame. This will release the preload adjustment wheel. Doc No: ATS-638191300 Revision: G RATCHET RELEASE LEVER Figure 11 SQUEEZE THE LINK IN THE HANDLE HOLD THE HAND TOOL IN POSITION Figure 12 SETTING WHEEL Release Date: 01-22-08 Revision Date: 05-05-16 UNCONTROLLED COPY Page 7 of 9 Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals 2. Rotate the setting wheel counter-clockwise (CCW) to increase handle force. The numbers will display higher. To decrease handle force, rotate the setting wheel clockwise (CW). 3. Release the link to lock the setting wheel in place. 4. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted. Warranty This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling. CAUTIONS: 1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for production use. Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. Certification Molex does not certify or re-certify hand tools but rather supplies the following guidelines for customers to re-certify hand tools. This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped 12.7mm (1/2") long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than 25mm (1.00") per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull testing. If the tool does not meet minimum pull force values, handle preload should be increased and the pull test rerun, (See How to Adjust Preload). When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and replaced. Doc No: ATS-638191300 Revision: G Release Date: 01-22-08 Revision Date: 05-05-16 UNCONTROLLED COPY Page 8 of 9 Hand Crimp Tool For Standard .062" Pin and Socket Crimp Terminals PARTS LIST Item Number REF 1 2 3 Order Number 63819-1300 63819-1375 63810-0104 63810-0105 Description Hand Crimp Tool Locator Assembly Spring, Return Spring, Ratchet Quantity Figure 13 1 1 1 2 1 RATCHET RELEASE LEVER Figure 13 3 Visit our Web site at http://www.molex.com Doc No: ATS-638191300 Revision: G Release Date: 01-22-08 Revision Date: 05-05-16 UNCONTROLLED COPY Page 9 of 9