Data Sheet October 5, 2013 EQW012/020/023/025 Series Eighth-Brick DC-DC Converters: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Current RoHS Compliant Features Applications Distributed power architectures Wireless Networks Enterprise Networks Optical and Access Network Equipment Latest generation IC's (DSP, FPGA, ASIC) and Microprocessor powered applications. Options Remote On/Off logic (positive or negative) Surface Mount (-S Suffix) Short pins Alternative output voltage adjustment equations (1.2V output only, -V Suffix) Compliant to RoHS EU Directive 2002/95/EC (-Z versions) Compliant to ROHS EU Directive 2002/95/EC with lead solder exemption (non-Z versions) Delivers up to 25A Output current High efficiency - 91% at 5.0Vdc full load (Vin=48Vdc) Low output ripple and noise Surface mount or through hole Industry standard Eight brick footprint 57.9mm x 22.8mm x 8.5mm(MAX) (2.28in x 0.9in x 0.335in) Constant switching frequency Remote On/Off Positive logic (primary referenced) Remote Sense Adjustable output voltage ( 10%) Output overvoltage and overcurrent protection Input undervoltage lockout Output overcurrent and overvoltage protection Over-temperature protection Wide operating temperature range (-40C to 85C) UL* 60950-1 Recognized, CSA C22.2 No. 60950-1 rd 03 Certified, and VDE 0805 (IEC60950, 3 edition) Licensed ISO** 9001 and ISO14001 certified manufacturing facilities Meets the voltage and current requirements for ETSI 300-132-2 and complies with and licensed for rd Basic insulation rating per IEC60950 3 edition Description The EQW series, Eighth-brick power modules are isolated dc-dc converters that can deliver up to 25A of output current and provide a precisely regulated output voltage over a wide range of input voltages (Vi = 36 -75Vdc). The modules achieve full load efficiency of 88% at 3.3V output voltage. The open frame modules construction, available in both surface-mount and through-hole packaging, enable designers to develop cost- and space-efficient solutions. Standard features include remote On/Off, remote sense, output voltage adjustment, overvoltage, overcurrent and overtemperature protection. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards Document No: DS03-74 ver. 1.27 PDF name: EQW12-25.pdf Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit EQW VIN -0.3 80 Vdc EQW VIN, trans -0.3 100 Vdc All TA -40 85 C Storage Temperature All Tstg -55 125 C I/O Isolation Voltage (100% factory Hi-Pot tested) All 1500 Vdc Input Voltage Continuous Transient (100ms) Operating Ambient Temperature (see Thermal Considerations section) Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 36 48 75 Vdc Maximum Input Current All IIN,max 3 Adc All IIN,No load 75 mA All IIN,stand-by 3 mA Inrush Transient All It Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12H source impedance; VIN=0V to 75V, IO= IOmax ; see Test Configuration section) All 13 mAp-p Input Ripple Rejection (120Hz) All 50 dB (VIN=0V to 75V, IO=IO, max) Input No Load Current (Vin = 48Vdc, Io = 0, module enabled) Input Stand-by Current (Vin = 48Vdc, module disabled) EMC, EN55022 2 2 1 As See EMC Considerations section CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of a sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer's data sheet for further information. LINEAGE POWER 2 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit Output Voltage Set-point 1.2 Vdc VO, set 1.18 1.2 1.22 Vdc 1.5 Vdc VO, set 1.47 1.5 1.53 Vdc 1.8 Vdc VO, set 1.76 1.8 1.84 Vdc 2.5V dc VO, set 2.45 2.5 2.55 Vdc 3.3 Vdc VO, set 3.25 3.3 3.35 Vdc 5.0 Vdc VO, set 4.90 5.0 5.10 Vdc (VIN=VIN,nom, IO=IO, max, Tref=25C) 1.2 Vdc VO 1.16 1.24 Vdc (Over all operating input voltage, resistive load, 1.5 Vdc VO 1.45 1.55 Vdc and temperature conditions until end of life) 1.8 Vdc VO 1.74 1.86 Vdc 2.5V dc VO 2.42 2.57 Vdc 3.3 Vdc VO 3.2 3.4 Vdc 5.0 Vdc VO 4.85 5.15 Vdc 1.8Vdc VO -10 +12 % VO, set 2.5Vdc VO -10 +20 % VO, set 3.3Vdc VO -20 +10 % VO, set All others VO -10.0 +10 % VO, set % VO, set Output Voltage Adjustment Range Selected by external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All 0.1 Load (IO=IO, min to IO, max) All 10 mV Temperature (Tref=TA, min to TA, max) All 0.2 % VO, set RMS (5Hz to 20MHz bandwidth) 5.0 Vdc 18 35 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) 5.0 Vdc 50 90 mVpk-pk RMS (5Hz to 20MHz bandwidth) All others 8 20 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All others 40 75 mVpk-pk F Output Ripple and Noise on nominal output measured with 10F Tantalum, 1F ceramic (VIN=VIN, nom and IO=IO, min to IO, max) External Capacitance* Output Current Output Current Limit Inception (Vo = 90% of VO, set) LINEAGE POWER 5.0 Vdc CO, max 0 3000 All others CO, max 0 5000 F 1.2 Vdc Io 0 25.0 Adc 1.5 Vdc Io 0 25.0 Adc 1.8 Vdc Io 0 25.0 Adc 2.5V dc Io 0 23.0 Adc 3.3 Vdc Io 0 20.0 Adc 5.0 Vdc Io 0 12.0 Adc 1.2 Vdc IO, lim 35 Adc 1.5 Vdc IO, lim 35 Adc 1.8 Vdc IO, lim 35 Adc 2.5V dc IO, lim 30 Adc 3.3 Vdc IO, lim 25 Adc 5.0 Vdc IO, lim 15 Adc 3 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit Output Short-circuit Current 1.2 Vdc Io,sc 42 Adc 1.5 Vdc Io,sc 42 Adc 1.8 Vdc Io,sc 42 Adc 2.5V dc Io,sc 40 Adc 3.3 Vdc Io,sc 37 Adc 5.0 Vdc Io,sc 25 Adc 1.2 Vdc 81.0 % VIN=VIN, nom, TA=25C 1.5 Vdc 81.0 % IO=IO, max , VO= VO,set 1.8 Vdc 84.0 % 2.5V dc 87.0 % 3.3 Vdc 88.0 % 5.0 Vdc 91.0 % All fsw 285 kHz (Io/t=0.1A/s; Vin=Vin,set; TA=25C) Load Change from Io= 50% to 75% of Io,max; 10F Tantalum, 1F ceramic external capacitance Peak Deviation All Vpk 200 mV Settling Time (Vo<10% peak deviation) All ts 200 s (Io/t=0.1A/s; Vin=Vin,set; TA=25C) Load Change from Io= 50% to 25% of Io,max; 10F Tantalum, 1F ceramic external capacitance Peak Deviation Settling Time (Vo<10% peak deviation) All Vpk 200 mV All ts 200 s (Vo = 0.25V) Efficiency Switching Frequency Dynamic Load Response Isolation Specifications Symbol Min Typ Max Isolation Capacitance Parameter CISO 1000 Unit pF Isolation Resistance RISO 10 M Device Min Typ Max Unit General Specifications Parameter Calculated Reliability Based upon Telcordia SR332 Issue 2: Method I, Case 1, (IO=80%IO, max, TA=40C, Airflow = 200 lfm), 90% confidence Weight LINEAGE POWER MTBF F-S 3,287,361 Hours FIT F-S 304 10 /Hours 15.2 (0.6) 9 g (oz.) 4 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit All Ion/off 0.15 1.0 mA All Von/off -0.7 1.2 V Logic High - (Typ = Open Collector) All Von/off 15 V Logic High maximum allowable leakage current All Ion/off 10 A All Tdelay 20 msec All Tdelay 12 msec All Trise Remote On/Off Signal Interface (VIN=VIN, min to VIN, max ; open collector or equivalent, Signal referenced to VIN- terminal) Negative Logic: device code suffix "1" Logic Low = module On, Logic High = module Off Positive Logic: No device code suffix required Logic Low = module Off, Logic High = module On Logic Low Specification Remote On/Off Current - Logic Low On/Off Voltage: Logic Low Turn-On Delay and Rise Times (VI =48Vdc, IO=IO, max , VO to within 1% of steady state) Case 1: On/Off input is set to Logic high and then input power is applied (delay from instant at which VI = VI,min until Vo = 10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is set to logic high (delay from instant at which Von/Off = 0.9V until Vo = 10% of Vo, set) Output voltage Rise time (time for Vo to rise from 10% of Vo, set to 90% of Vo, set) Output voltage overshoot (Io = 80% of Io,max, VI = 48Vdc TA=25C) Output Voltage Remote Sense Output Overvoltage Protectionn (Clamp) Overtemperature Protection 0.9 msec All 5 %VO, set 1.2, 1.5, 1.8Vdc 0.25 Vdc 2.5, 3.3, 5.0 Vdc 10 %VO, set 1.2 Vdc VO, limit 2.0 2.8 Vdc 1.5 Vdc VO, limit 2.3 3.2 Vdc 1.8 Vdc VO, limit 2.3 3.2 Vdc 2.5V dc VO, limit 3.1 3.7 Vdc 3.3 Vdc VO, limit 4.0 4.6 Vdc 5.0 Vdc VO, limit 6.1 7.0 Vdc All Tref 125 C All 32 36 Vdc All 25 27 Vdc (See thermal section) Input Undervoltage Lockout Turn-on Threshold Turn-off Threshold LINEAGE POWER 5 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Characteristic Curves The following figures provide typical characteristics for the EQW025A0P1 (1.2V, 25A) at 25C. The figures are identical for either positive or negative Remote On/Off logic. 27 84 24 OUTPUT CURRENT, Io (A) 86 EFFICIENCY (%) 82 80 78 76 Vin=75V 74 Vin=48V 72 Vin=36V 70 0 5 10 15 20 25 LINEAGE POWER 6 3 0 200 LFM 300 LFM 400 LFM 30 40 50 60 70 80 90 O INPUT VOLTAGE VO (V) (1V/div) OUTPUT VOLTAGE Figure 4. . Derating Output Current versus Local Ambient Temperature and Airflow TIME, t (5ms/div) VOn/off (V) (5V/div) ON/OFF VOLTAGE VO (V) (1V/div) Figure 5. Typical Start-Up with application of Vin (Vin = 48Vdc, Io = 25A). OUTPUT VOLTAGE Figure 3. Typical Transient Response to Dynamic Load change Load from 50% to 75% to 50% of Full load at 48 Vdc Input. 9 NC 100 LFM VOn/off (V) (20V/div) VO (V) (20mV/div) OUTPUT VOLTAGE OUTPUT VOLTAGE VO (V) (100mV/div) OUTPUT CURRENT IO, (A) (10A/div) TIME, t (100s/div) 15 12 AMBIENT TEMPERATURE, TA C TIME, t (1s/div) Figure 2. Typical Output Ripple and Noise (Vin =48Vdc, Io = 25A). 18 20 OUTPUT CURRENT, Io (A) Figure 1. Typical Converter Efficiency Vs. Output current at Room Temperature. 21 TIME, t (5ms/div) Figure 6. Typical Start-Up Using Remote On/Off, negative logic version shown (Vin = 48Vdc, Io = 25A). 6 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Characteristic Curves (continued) The following figures provide typical characteristics for the EQW025A0M (1.5V, 25A) at 25C. The figures are identical for either positive or negative Remote On/Off logic. 27 86 24 OUTPUT CURRENT, Io (A) 88 EFFICIENCY (%) 84 82 80 78 76 Vin=75V 74 Vin=48V 72 Vin=36V 70 0 5 10 15 20 25 LINEAGE POWER 9 6 3 0 NC 100 LFM 200 LFM 300 LFM 400 LFM 30 40 50 60 70 80 90 O INPUT VOLTAGE VO (V) (1V/div) OUTPUT VOLTAGE Figure 10. . Derating Output Current versus Local Ambient Temperature and Airflow TIME, t (5ms/div) VOn/off (V) (5V/div) VO (V) (1V/div) Figure 11. Typical Start-Up with application of Vin (Vin = 48Vdc, Io = 25A). ON/OFF VOLTAGE OUTPUT VOLTAGE Figure 9. Typical Transient Response to Dynamic Load change Load from 50% to 75% to 50% of Full load at 48 Vdc Input. 12 VOn/off (V) (20V/div) VO (V) (20mV/div) OUTPUT VOLTAGE OUTPUT VOLTAGE VO (V) (200mV/div) OUTPUT CURRENT IO, (A) (5A/div) TIME, t (100s/div) 15 AMBIENT TEMPERATURE, TA C TIME, t (1s/div) Figure 8. Typical Output Ripple and Noise (Vin =48Vdc, Io = 25A). 18 20 OUTPUT CURRENT, Io (A) Figure 7. Typical Converter Efficiency Vs. Output current at Room Temperature. 21 TIME, t (5ms/div) Figure 12. Typical Start-Up Using Remote On/Off, negative logic version shown (Vin = 48Vdc, Io = 25A). 7 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Characteristic Curves (continued) The following figures provide typical characteristics for the EQW025A0Y (1.8V, 25A) at 25C. The figures are identical for either positive or negative Remote On/Off logic. 27 88 24 OUTPUT CURRENT, Io (A) 90 EFFICIENCY (%) 86 84 82 80 Vin=75V 78 Vin=48V 76 Vin=36V 74 72 0 5 10 15 20 LINEAGE POWER 6 3 200 LFM 300 LFM 400 LFM 30 40 50 60 70 80 90 O VO (V) (1V/div) VOn/off (V) (20V/div) OUTPUT VOLTAGE Figure 16. . Derating Output Current versus Local Ambient Temperature and Airflow INPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE TIME, t (5ms/div) VO (V) (1V/div) VOn/off (V) (5V/div) OUTPUT VOLTAGE Figure 17. Typical Start-Up with application of Vin (Vin = 48Vdc, Io = 25A). ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (100mV/div) OUTPUT CURRENT IO, (A) (10A/div) Figure 15. Typical Transient Response to Dynamic Load change Load from 50% to 75% to 50% of Full load at 48 Vdc Input. 9 NC 100 LFM AMBIENT TEMPERATURE, TA C TIME, t (1s/div) TIME, t (100s/div) 15 12 20 OUTPUT CURRENT, Io (A) Figure 14. Typical Output Ripple and Noise (Vin =48Vdc, Io = 25A). 18 0 25 Figure 13. Typical Converter Efficiency Vs. Output current at Room Temperature. 21 TIME, t (5ms/div) Figure 18. Typical Start-Up Using Remote On/Off, negative logic version shown (Vin = 48Vdc, Io = 25A). 8 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Characteristic Curves (continued) The following figures provide typical characteristics for the EQW023A0G (2.5V, 23A) at 25C. The figures are identical for either positive or negative Remote On/Off logic. 24 90 21 OUTPUT CURRENT, Io (A) 92 EFFICIENCY (%) 88 86 84 82 Vin=75V 80 Vin=48V 78 Vin=36V 76 74 0 5 10 15 20 LINEAGE POWER 9 200 LFM 6 300 LFM 3 400 LFM 0 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE VO (V) (1V/div) VOn/off (V) (20V/div) INPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE TIME, t (5ms/div) VO (V) (1V/div) VOn/off (V) (5V/div) OUTPUT VOLTAGE Figure 23. Typical Start-Up with application of Vin (Vin = 48Vdc, Io = 23A). ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (100mV/div) OUTPUT CURRENT IO, (A) (10A/div) Figure 21. Typical Transient Response to Dynamic Load change Load from 50% to 75% to 50% of Full load at 48 Vdc Input. 100 LFM Figure 22. . Derating Output Current versus Local Ambient Temperature and Airflow TIME, t (1s/div) TIME, t (100s/div) NC 12 O OUTPUT CURRENT, Io (A) Figure 20. Typical Output Ripple and Noise (Vin =48Vdc, Io = 23A). 15 20 25 Figure 19. Typical Converter Efficiency Vs. Output current at Room Temperature. 18 TIME, t (5ms/div) Figure 24. Typical Start-Up Using Remote On/Off, negative logic version shown (Vin = 48Vdc, Io = 23A). 9 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Characteristic Curves (continued) The following figures provide typical characteristics for the EQW020A0F (3.3V, 20A) at 25C. The figures are identical for either positive or negative Remote On/Off logic. 91 22 20 OUTPUT CURRENT, Io (A) EFFICIENCY (%) 88 85 82 Vin=75V 79 Vin=48V 76 Vin=36V 73 70 0 4 8 12 16 20 LINEAGE POWER 10 8 6 4 2 0 NC 100 LFM 200 LFM 300 LFM 400 LFM 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE VO (V) (1V/div) VOn/off (V) (20V/div) TIME, t (5ms/div) VOn/off (V) (5V/div ON/OFF VOLTAGE VO (V) (1V/div) Figure 29. Typical Start-Up with application of Vin (Vin = 48Vdc, Io = 20A). OUTPUT VOLTAGE Figure 27. Typical Transient Response to Dynamic Load change Load from 50% to 75% to 50% of Full load at 48 Vdc Input. 12 Figure 28 . Derating Output Current versus Local Ambient Temperature and Airflow INPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE OUTPUT VOLTAGE VO (V) (100mV/div) OUTPUT CURRENT IO, (A) (10A/div) TIME, t (100s/div) 14 O TIME, t (1s/div) Figure 26. Typical Output Ripple and Noise (Vin =48Vdc, Io = 20A). 16 20 OUTPUT CURRENT, Io (A) Figure 25. Typical Converter Efficiency Vs. Output current at Room Temperature. 18 TIME, t (5ms/div) Figure 30. Typical Start-Up Using Remote On/Off, negative logic version shown (Vin = 48Vdc, Io = 20A). 10 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Characteristic Curves (continued) The following figures provide typical characteristics for the EQW012A0A (5.0V, 12A) at 25C. The figures are identical for either positive or negative Remote On/Off logic. 14 91 12 OUTPUT CURRENT, Io (A) 94 EFFICIENCY (%) 88 85 82 Vin=75V 79 Vin=48V 76 Vin=36V 73 70 0 3 6 9 LINEAGE POWER 2 200 LFM 300 LFM 400 LFM 0 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE VO (V) (1V/div) VOn/off (V) (20V/div) INPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE TIME, t (5ms/div) VO (V) (1V/div) VOn/off (V) (5V/div) OUTPUT VOLTAGE Figure 35. Typical Start-Up with application of Vin (Vin = 48Vdc, Io = 12A). ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (100mV/div) OUTPUT CURRENT IO, (A) (10A/div) Figure 33. Typical Transient Response to Dynamic Load change Load from 50% to 75% to 50% of Full load at 48 Vdc Input. 4 100 LFM Figure 34 . Derating Output Current versus Local Ambient Temperature and Airflow TIME, t (1s/div) TIME, t (100s/div) 6 O OUTPUT CURRENT, Io (A) Figure 32. Typical Output Ripple and Noise (Vin =48Vdc, Io = 12A). 8 20 12 Figure 31. Typical Converter Efficiency Vs. Output current at Room Temperature. NC 10 TIME, t (5ms/div) Figure 36. Typical Start-Up Using Remote On/Off, negative logic version shown (Vin = 48Vdc, Io = 12A). 11 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Test Configurations Safety Considerations CURRENT PROBE TO OSCILLOSCOPE LTEST VIN(+) BATTERY 12H CS 220F 33F E.S.R.<0.1 E.S.R. <0.1 @ 100kHz @ 20C 100kHz VIN(-) NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 12H. Capacitor CS offsets possible battery impedance. Measure current as shown above. Figure 37. Input Reflected Ripple Current Test Setup. COPPER STRIP VO (+) RESISTIVE LOAD 1uF . 10uF For safety-agency approval of the system in which the power module is used, the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standard, i.e., UL60950-1, CSA C22.2 No. 60950-1rd 03 and VDE 0805 (IEC60950, 3 Ed). These converters have been evaluated to the spacing requirements for Basic Insulation, per the above safety standards; and 1500Vdc is applied from Vin to Vout to 100% of outgoing production.. For end products connected to -48V dc, or -60Vdc nominal DC MAINS (i.e. central office dc battery plant), no further fault testing is required. *Note: -60V dc nominal battery plants are not available in the U.S. or Canada. For all input voltages, other than DC MAINS, where the input voltage is less than 60V dc, if the input meets all of the requirements for SELV, then: SCOPE V O (-) GROUND PLANE NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 38. Output Ripple and Noise Test Setup. Rdistribution Rcontact Rcontact VIN(+) Rdistribution Rcontact Rcontact VO. IO VIN. IIN The input source is to be provided with reinforced insulation from any hazardous voltage, including the AC mains. One Vi pin and one Vo pin are to be reliably earthed, or both the input and output pins are to be kept floating. Another SELV reliability test is conducted on the whole system, as required by the safety agencies, on the combination of supply source and the subject module to verify that under a single fault, hazardous voltages do not appear at the module's output. Rdistribution Figure 39. Output Voltage and Efficiency Test Setup. = COM NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Efficiency One pole of the input and one pole of the output are to be grounded, or both circuits are to be kept floating, to maintain the output voltage to ground voltage within ELV or SELV limits. For all input sources, other than DC MAINS, where the input voltage is between 60 and 75V dc (Classified as TNV-2 in Europe), the following must be adhered to, if the converter's output is to be evaluated for SELV: RLOAD VO VIN(-) Rdistribution VO VIN x The output may be considered SELV. Output voltages will remain within SELV limits even with internally-generated non-SELV voltages. Single component failure and fault tests were performed in the power converters. 100 % Design Considerations The power module should be connected to a low ac-impedance source. A highly inductive source impedance can affect the stability of the power module. For the test configuration in Figure 37, a 33F electrolytic capacitor (ESR<0.7 at 100kHz), mounted close to the power module helps ensure the stability of the unit. Consult the factory for further application guidelines. LINEAGE POWER The power module has ELV (extra-low voltage) outputs when all inputs are ELV. All flammable materials used in the manufacturing of these modules are rated 94V-0, and UL60950 A.2 for reduced thickness. The input to these units is to be provided with a maximum 6A time- delay in the unearthed lead. 12 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Feature Description Remote On/Off Two remote on/off options are available. Positive logic turns the module on during a logic high voltage on the ON/OFF pin, and off during a logic low. Negative logic remote On/Off, device code suffix "1", turns the module off during a logic high and on during a logic low. To turn the power module on and off, the user must supply a switch (open collector or equivalent) to control the voltage (Von/off) between the ON/OFF terminal and the VIN(-) terminal (Figure 40). Logic low is -0.7V Von/off 1.2V. The maximum Ion/off during a logic low is 1mA, the switch should be maintain a logic low level while sinking this current. During a logic high, the typical Von/off generated by the module is 15V, and the maximum allowable leakage current at Von/off = 15V is 10A. If not using the remote on/off feature: For positive logic, leave the ON/OFF pin open. For negative logic, short the ON/OFF pin to VIN(-). multiplied by the output current. When using remote sense and trim, the output voltage of the module can be increased, which at the same output current would increase the power output of the module. Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power (Maximum rated power = Vo,set x Io,max). SENSE(+) SENSE(-) SUPPLY II VI(+) VO(+) VI(-) VO(-) CONTACT RESISTANCE IO LOAD CONTACT AND DISTRIBUTION LOSSES Figure 41. Effective Circuit Configuration for remote sense operation. Output Voltage Set-Point Adjustment (Trim) Trimming allows the output voltage set point to be increased or decreased, this is accomplished by connecting an external resistor between the TRIM pin and either the VO(+) pin or the VO(-) pin (COM pin) . VIN(+) VO Ion/off VIN(+) VO(+) Rtrim-up ON/OFF ON/OFF Von/off LOAD VOTRIM COM Rtrim-down VIN(-) VIN(-) Figure 40. Circuit configuration for using Remote On/Off Implementation. Remote Sense Remote sense minimizes the effects of distribution losses by regulating the voltage at the remote-sense connections (See Figure 41). The voltage between the remote-sense pins and the output terminals must not exceed the output voltage sense range given in the Feature Specifications table: VO(-) Figure 42. Circuit Configuration to Trim Output Voltage. Connecting an external resistor (Rtrim-down) between the TRIM pin and the Vo(-) (or Sense(-)) pin decreases the output voltage set point. To maintain set point accuracy, the trim resistor tolerance should be 0.1%. The following equation determines the required external resistor value to obtain a percentage output voltage change of % [VO(+) - VO(-)] - [SENSE(+) - SENSE(-)] 0.5 V Although the output voltage can be increased by both the remote sense and by the trim, the maximum increase for the output voltage is not the sum of both. The maximum increase is the larger of either the remote sense or the trim. The amount of power delivered by the module is defined as the voltage at the output terminals LINEAGE POWER 13 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Feature Description (Continued) Output Voltage Set-Point Adjustment (Trim) (Continued) For output voltage: 1.2 V to 12V Alternative voltage programming for output voltage: 1.2V (-V Option) An alternative set of trimming equations is available as an option for 1.0V and 1.2V output modules, by ordering the -V option. These equations will reduce the resistance of the external programming resistor, making the impedance into the module trim pin lower for applications in high electrical noise applications. 510 Rtrim down 10.2 % R trim down Where Vo, set Vdesired % 100 Vo, set For example, to trim-down the output voltage of 2.5V module (EQW023A0G1) by 8% to 2.3V, Rtrim-down is calculated as follows: % 8 510 Rtrim down 10.2 8 Rtrim down 53.55 Connecting an external resistor (Rtrim-up) between the TRIM pin and the VO(+) (or Sense (+)) pin increases the output voltage set point. The following equations determine the required external resistor value to obtain a percentage output voltage change of %: For output voltage: 1.5 V to 12V 5.1 Vo, set (100 %) 510 10.2 Rtrim up % 1.225 % For output voltage: 1.2 5.1 Vo, set (100 %) 510 Rtrim up 10.2 0.6 % % Where Vdesired Vo, set % 100 Vo, set For example, to trim-up the output voltage of 1.5V module (EQW025A0M1) by 6% to 1.59V, Rtrim-up is calculated is as follows: % 6 5.1 1.5 (100 6) 510 Rtrim up 10.2 1 . 225 6 6 Rtrim up 15.12 LINEAGE POWER R trim Where up 100 2 % 100 % V V o , set % desired V o , set 100 For example, to trim-up the output voltage of 1.2V module (EQW025A0P/P1-V) by 5% to 1.26V, Rtrim-up is calculated is as follows: % 5 R trim up 100 5 Rtrim up 20 .0 The value of the external trim resistor for the optional -V 1.2V module is only 20% of the value required with the standard trim equations. At 48Vin (+/- 2.5V), EQW series modules can be trim down to 20% over the entire temperature range. This allows for margining the unit during manufacturing process if the set point voltage is lower than the standard output voltage. Please consult your local Lineage Power field application engineer for additional details. The voltage between the Vo(+) and Vo(-) terminals must not exceed the minimum output overvoltage protection value shown in the Feature Specifications table. This limit includes any increase in voltage due to remote-sense compensation and output voltage set-point adjustment trim. Although the output voltage can be increased by both the remote sense and by the trim, the maximum increase for the output voltage is not the sum of both. The maximum increase is the larger of either the remote sense or the trim. The amount of power delivered by the module is defined as the voltage at the output terminals multiplied by the output current. When using remote sense and trim, the output voltage of the module can be increased, which at the same output current would increase the power output of the module. Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power (Maximum rated power = Vo,set x Io,max). 14 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Feature Description (Continued) operation this temperature should not exceed 115 oC. The output power of the module should not exceed the rated power for the module (Vo, set x Io, max). Tref Overcurrent Protection To provide protection in a fault (output overload) condition, the module is equipped with internal current-limiting circuitry, and can endure current limiting continuously. At the instance of current-limit inception, the output current begins to tail-out. When an overcurrent condition exists beyond a few seconds, the module enters a "hiccup" mode of operation, whereby it shuts down and automatically attempts to restart upon cooling. While the fault condition exists, the module will remain in this hiccup mode, and can remain in this mode until the fault is cleared. The unit operates normally once the output current is reduced back into its specified range. Output Over Voltage Protection The output overvoltage protection clamp consists of control circuitry, independent of the primary regulation loop, that monitors the voltage on the output terminals. This control loop has a higher voltage set point than the primary loop (See the overvoltage clamp values in the Feature Specifications Table). In a fault condition, the overvoltage clamp ensures that the output voltage does not exceed Vo,ovsd, max. This provides a redundant voltage-control that reduces the risk of output overvoltage. Input Undervoltage Lockout At input voltages below the input undervoltage lockout limit, the module operation is disabled. The module will begin to operate at an input voltage between the undervoltage lockout limit and the minimum operating input voltage. Air Flow Figure 43. Tref Temperature Measurement Location. Please refer to the Application Note "Thermal Characterization Process For Open-Frame BoardMounted Power Modules" for a detailed discussion of thermal aspects including maximum device temperatures. Heat Transfer via Convection Increased airflow over the module enhances the heat transfer via convection. Derating figures showing the maximum output current that can be delivered by each module versus local ambient temperature (TA) for natural convection and up to 2m/s (400 ft./min) are shown in the respective Characteristics Curves section. Overtemperature Protection To provide protection under certain fault conditions, the unit is equipped with a thermal shutdown circuit. The unit will shutdown if the thermal reference point Tref (Figure 43), exceeds 125oC (typical), but the thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. The module will automatically restarts after it cools down. Thermal Considerations The power modules operate in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The thermal reference point, Tref used in the specifications is shown in Figure 43. For reliable LINEAGE POWER 15 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output EMC Considerations The figure 44 shows a suggested configuration to meet the conducted emission limits of EN55022 Class B. Ld1 Vin+ CY1 CX1 CX5 CX3 CX4 CX2 Vout+ Copper paths must not be routed beneath the power module mounting inserts. Recommended SMT layout shown in the mechanical section are for reference only. SMT layout depends on the end PCB configuration and the location of the load. For additional layout guide-lines, refer to FLTR100V10 data sheet or contact your local Lineage Power field application engineer. EQW CY2 Vin- Vout- LC1 Cim Figure 44. Suggested Input Filter Configuration for EN55022 Class B. Filter components: Cx1: 47uF aluminum electrolytic, 100V (Nichicon PW series) Cx2: 2x1uF ceramic, 100V (TDK C4532X7R2A105M) Cx3: 2x1uF ceramic, 100V (TDK C4532X7R2A105M) Cx4: 2x1uF ceramic, 100V (TDK C4532X7R2A105M) Cx5: 100uF aluminum electrolytic, 100V (Nichicon PW series) Cy3, Cy4: 3300pF ceramic, 1500V (AVX 1812SC332MAT1A) Cim: 3300pF ceramic, 1500V (AVX 1812SC332MAT1A) Lc1: 768 uH, 4.7A (Pulse Engineering P0422) Ld1: 4.7 uH, 5.5A (Vishay IHLP-2525CZ) Level [dBV] 80 70 EN55022 Class B Conducted Average dBuV 60 50 + 40 30 20 10 0 150k 300k 500k 1M 2M 3M 4M 5M Frequency [Hz] 7M 10M 30M Figure 45. EMC signature using recommended filter. For further information on designing for EMC compliance, please refer to the FLTR100V10 data sheet (FDS01-043EPS). Layout Considerations LINEAGE POWER 16 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Mechanical Outline for Through-Hole Module Dimensions are in millimeters and [inches]. Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (Unless otherwise indicated) x.xx mm 0.25 mm [x.xxx in 0.010 in.] Top View Side View * OPTIONAL PIN LENGTHS SHOWN IN TABLE 2 DEVICE OPTIONS Bottom View Pin Function 1 VI(+) 2 On/Off 3 VI(-) 4 Vo(-) 5 Sense(-) 6 Trim 7 Sense(+) 8 Vo(+) LINEAGE POWER 17 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Mechanical Outline for Surface Mount Power module. Dimensions are in millimeters and [inches]. Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (Unless otherwise indicated) x.xx mm 0.25 mm [x.xxx in 0.010 in.] Top View Side View Bottom View Pin Function 1 VI(+) 2 On/Off 3 VI(-) 4 Vo(-) 5 Sense(-) 6 Trim 7 Sense(+) 8 Vo(+) LINEAGE POWER 18 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Recommended Pad Layout for Surface-Mount Modules Dimensions are in millimeters and [inches]. Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (Unless otherwise indicated) x.xx mm 0.25 mm [x.xxx in 0.010 in.] Low Current High Current 1 . 0 LINEAGE POWER 19 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Recommended Pad Layout for Through-Hole modules Dimensions are in millimeters and [inches]. Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (Unless otherwise indicated) x.xx mm 0.25 mm [x.xxx in 0.010 in.] Component side view LINEAGE POWER 20 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Packaging Details The surface mount versions of the EQW surface mount modules (suffix -S) are supplied as standard in the plastic tray shown in Figure 46. The tray has external dimensions of 135.1mm (W) x 321.8mm (L) x 12.42mm (H) or 5.319in (W) x 12.669in (L) x 0..489in (H). Tray Specification Material Antistatic coated PVC Max surface resistivity Color Capacity Min order quantity trays) 10 /sq Clear 12 power modules 48 pcs (1box of 4 full 12 Each tray contains a total of 12 power modules. The trays are self-stacking and each shipping box will contain 4 full trays plus one empty hold down tray giving a total number of 48 power modules. Figure 46. Surface Mount Packaging Tray. LINEAGE POWER 21 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Through-Hole Soldering Information The RoHS-compliant through-hole products use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant components. They are designed to be processed through single or dual wave soldering machines. The pins have an RoHS-compliant finish that is compatible with both Pb and Pb-free wave soldering processes. A maximum preheat rate of 3C/s is suggested. The wave preheat process should be such that the temperature of the power module board is kept below 210C. For Pb solder, the recommended pot temperature is 260C, while the Pb-free solder pot is 270C max. Not all RoHS-compliant through-hole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is needed, please consult with your Lineage Power representative for more details. Surface Mount Information Pick and Place The SMT versions of the EQW series of DC-to-DC power converters use an open-frame construction and are designed for surface mount assembly within a fully automated manufacturing process. The EQW-S series modules are fitted with a Kapton label designed to provide a large flat surface for pick and placing. The label is located covering the center of gravity of the power module. The label meets all the requirements for surface-mount processing, as well as meeting UL safety agency standards. The label will withstand reflow temperatures up to 300C. The label also carries product information such as product code, date and location of manufacture. Figure 47. Pick and Place Location. Z plane Height The `Z' plane height of the pick and place label is 9.15 mm (0.360 in) nominal with an RSS tolerance of +/0.25 mm. relatively large mass when compared with conventional smt components. Variables such as nozzle size, tip style, vacuum pressure and placement speed should be considered to optimize this process. The minimum recommended nozzle diameter for reliable operation is 6mm. The maximum nozzle outer diameter, which will safely fit within the allowable component spacing, is 9 mm. Oblong or oval nozzles up to 11 x 9 mm may also be used within the space available. For further information please contact your local Lineage Power Technical Sales Representative. Reflow Soldering Information The surface mountable modules in the EQW family use our newest SMT technology called "Column Pin" (CP) connectors. Figure 48 shows the new CP connector before and after reflow soldering onto the end-board assembly. EQW Board Insulator Solder Ball End assembly PCB Figure 48. Column Pin Connector Before and After Reflow Soldering . The CP is constructed from a solid copper pin with an integral solder ball attached, which is composed of tin/lead (Sn63/Pb37) solder for non-Z codes, or Sn/Ag3.8/Cu0.7 (SAC) solder for -Z codes. The CP connector design is able to compensate for large amounts of co-planarity and still ensure a reliable SMT solder joint. Typically, the eutectic solder melts o o at 183 C (Sn/Pb solder) or 217-218 C (SAC solder), wets the land, and subsequently wicks the device connection. Sufficient time must be allowed to fuse the plating on the connection to ensure a reliable solder joint. There are several types of SMT reflow technologies currently used in the industry. These surface mount power modules can be reliably soldered using natural forced convection, IR (radiant infrared), or a combination of convection/IR. The following instructions must be observed when SMT soldering these units. Failure to observe these instructions may result in the failure of or cause damage to the modules, and can adversely affect long-term reliability. Nozzle Recommendations The module weight has been kept to a minimum by using open frame construction. Even so, they have a LINEAGE POWER 22 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Surface Mount Information (continued) Tin Lead Soldering The recommended linear reflow profile using Sn/Pb solder is shown in Figure 49 and 50. For reliable soldering the solder reflow profile should be established by accurately measuring the modules CP connector temperatures. both Pb-free solder profiles and MSL classification procedures. This standard provides a recommended forced-air-convection reflow profile based on the volume and thickness of the package (table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Fig. 51. 300 P eak Temp 235oC REFLOW TEMP (C) 250 Co o ling zo ne 1-4oCs -1 Heat zo ne max 4oCs -1 200 150 So ak zo ne 30-240s 100 Tlim above 205oC P reheat zo ne max 4oCs -1 50 Figure 51. Recommended linear reflow profile using Sn/Ag/Cu solder. 0 REFLOW TIME (S) Figure 49. Recommended Reflow Profile for Sn/Pb Solder. MSL Rating The EQW series SMT modules have a MSL rating of 2a. 240 MAX TEMP SOLDER (C) 235 Storage and Handling 230 225 220 215 210 205 200 0 10 20 30 40 50 60 TIME LIMIT (S) o Figure 50. Time Limit, Tlim, Curve Above 205 C Reflow . The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at conditions of 30C and 60% relative humidity varies according to the MSL rating (see J-STD-033A). The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40 C, < 90% relative humidity. Lead Free Soldering The -Z version SMT modules of EQW series are lead-free (Pb-free) and RoHS compliant and are compatible in a Pb-free soldering process. Failure to observe the instructions below may result in the failure of or cause damage to the modules and can adversely affect long-term reliability. Pb-free Reflow Profile Power Systems will comply with J-STD-020 Rev. D (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for LINEAGE POWER Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Lineage Power Board Mounted Power Modules: Soldering and Cleaning Application Note (AN04-001). 23 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Table 1. Device Codes Product codes Input Voltage EQW012A0A1 EQW012A0A61 EQW012A0A81 EQW012A0A1Z EQW012A0A6Z EQW012A0A1-S EQW012A0A1-SZ EQW020A0F EQW020A0F1 EQW020A0F1Z EQW020A0F61 EQW020A0F61Z EQW020A0F61-13 EQW020A0F8Z EQW020A0F1-S EQW020A0F1-SZ EQW023A0G1 EQW023A0G1-S EQW025A0Y61 EQW025A0Y61Z EQW025A0Y1Z EQW025A0M61 EQW025A0M1Z EQW025A0P1Z EQW025A0P1-SZ 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) LINEAGE POWER 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) 48V (36-75Vdc) Output Voltage 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 2.5V 2.5V 1.8 V 1.8 V 1.8 V 1.5 V 1.5 V 1.2 V 1.2 V Output Current 12 A 12 A 12 A 12 A 12 A 12 A 12 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 23 A 23 A 25 A 25 A 25 A 25 A 25 A 25 A 25 A Efficiency 91.0 % 91.0 % 91.0 % 91.0 % 91.0 % 91.0 % 91.0 % 88.0 % 88.0 % 88.0 % 88.0 % 88.0 % 88.0 % 88.0 % 88.0 % 88.0 % 87.0 % 87.0 % 84.0 % 84.0 % 84.0 % 81.0 % 81.0 % 81.0 % 81.0 % Connector Type Through hole Through hole Through hole Through hole Through hole SMT SMT Through hole Through hole Through hole Through hole Through hole Through hole Through hole SMT SMT Through hole SMT Through hole Through hole Through hole Through hole Through hole Through hole SMT Comcodes 108984444 108990280 108991650 CC109104972 CC109131570 108980889 109100162 108979428 108981952 CC109107050 108985698 CC109101796 CC109136710 CC109150455 108980905 109100170 108980624 108980921 CC109107091 108985706 CC109138913 108985714 CC109107067 CC109107083 109100187 24 Data Sheet October 5, 2013 EQW012/020/023/025 Series, Eighth-Brick Power Modules: 36 - 75Vdc Input; 1.2Vdc to 5Vdc Output; 12A to 25A Output Table 2. Device Options Option Suffix* 1 Negative remote on/off logic Short Pins: 3.68 mm 0.25 mm (0.145 in 0.010 in) 6 Short Pins: 2.79 mm 0.25 mm (0.110 in 0.010 in) Surface mount connections 8 -S Alternative Voltage Programming equations (1.0V and 1.2V modules only) -V RoHS Compliant -Z *Note: Legacy device codes may contain a -B option suffix to indicate 100% factory Hi-Pot tested to the isolation voltage specified in the Absolute Maximum Ratings table. The 100% Hi-Pot test is now applied to all device codes, with or without the -B option suffix. Existing comcodes for devices with the -B suffix are still valid; however, no new comcodes for devices containing the -B suffix will be created. Asia-Pacific Headquarters Tel: +65 6593 7211 World Wide Headquarters Lineage Power Corporation 601 Shiloh Road, Plano, TX 75074, USA +1-800-526-7819 (Outside U.S.A.: +1-972-244-9428) www.lineagepower.com e-mail: techsupport1@lineagepower.com Europe, Middle-East and Africa Headquarters Tel: +49 89 878067-280 India Headquarters Tel: +91 80 28411633 Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Lineage Power DC-DC products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents. (c) 2009 Lineage Power Corporation, (Plano, Texas) All International Rights Reserved. Document No: DS03-74 ver. 1.27 PDF name: EQW12-25.pdf