PT6100 Series 1 Amp Adjustable Positive Step-down Integrated Switching Regulator SLTS029A (Revised 6/30/2000) * * * * * * * 90% Efficiency Adjustable Output Voltage Internal Short Circuit Protection Over-Temperature Protection On/Off Control (Ground Off) Small SIP Footprint Meets Requirements for FCC Part 15; Class B limits for Radiated Emissions * Wide Input Range Pin-Out Information Pin Standard Application VOADJ 12 VIN 2,3,4 PT6100 VOUT 9,10,11 1 5,6,7,8 C1 INH C2 + Q1 COM COM C1 = Optional 1F ceramic Q1 = NFET C2 = Required 100F electrolytic Specifications 1 2 3 4 5 6 7 8 9 10 11 12 Function Inhibit (30V max) Vin Vin Vin GND GND GND GND Vout Vout Vout Vout Adj The PT6100 Series is a line of High-Performance 1 Amp, 12-Pin SIP (Single In-line Package) Integrated Switching Regulators (ISRs) designed to meet the on-board power conversion needs of battery powered or other equipment requiring high efficiency and small size. This high performance ISR family offers a unique combination of features combining 90% typical efficiency with open-collector on/off control and adjustable output voltage. Quiescent current in the shutdown mode is less than 100A. Ordering Information PT Series Suffix (PT1234X) PT6101 = +5 Volts PT6102 = +3.3 Volts PT6103 = +12 Volts Case/Pin Configuration Vertical Through-Hole Horizontal Through-Hole Horizontal Surface Mount N A C Pkg Style 200 PT6100 SERIES Characteristics (Ta =25C unless noted) Symbols Conditions Min Typ Max Units Output Current Io Over Vin range 0.1* -- 1.0 A Short Circuit Current Isc Vin = Vin min -- 3.5 -- Apk Input Voltage Range Vin 0.1 Io 1.0 A 9 -- 26 30/38** 30/38** V V Output Voltage Tolerance Vo Over Vin Range, Io = 1.0 A Ta = 0C to +60C -- 1.0 2.0 %Vo Line Regulation Regline Over Vin range -- 0.25 0.5 %Vo Load Regulation Regload 0.1 Io 1.0 A -- 0.25 0.5 %Vo Vo Ripple/Noise Vn Vin=Vin min, Io=1.0 A -- 2 -- %Vo Transient Response with Co = 100F ttr Vos 50% load change Vo over/undershoot -- -- 100 5.0 200 -- Sec %Vo Efficiency Vin=9V, Io=0.5A, Vo=3.3V Vin=9V, Io=0.5A, Vo=5V Vin=16V, Io=0.5A, Vo=12V -- -- -- 84 89 91 -- -- -- % % % Switching Frequency o Over Vin and Io ranges 400 500 600 kHz Shutdown Current Quiescent Current Isc Inl Vin = 15V Io = 0A, Vin =10V -- -- 100 10 -- -- A mA Output Voltage Adjustment Range Vo Below Vo Above Vo See Application Notes. Absolute Maximum Operating Temperature Range Ta -40 -- +85 C Recommended Operating Temperature Range Ta Free Air Convection, Vo= 3.3V (40-60LFM) Vo= 5V Vin=24V, Io=0.75A Vo= 12V -40 -40 -40 -- -- -- +85*** +85*** +80*** C Thermal Resistance ja Free Air Convection (40-60LFM) -- -- -- 50 40 40 -- -- -- C/W Storage Temperature Ts (Note: inhibit function cannot be used with Vin above 30V.) Vo = 3.3V Vo = 5V Vo = 12V Vo = 3.3V Vo = 5V Vo = 12V 9 16 -- -- V -40 -- +125 C Mechanical Shock Per Mil-STD-883D, Method 2002.3 1 msec, Half Sine, mounted to a fixture -- 500 -- G's Mechanical Vibration Per Mil-STD-883D, Method 2007.2 20-2000 Hz, Soldered in a PC board -- 10 -- G's -- 5.0 -- grams Weight * ISR will operate down to no load with reduced specifications. ** Input voltage cannot exceed 30V when the inhibit function is used. ***See Thermal Derating chart. Note: The PT6100 Series requires a 100F electrolytic or tantalum output capacitor for proper operation in all applications. For technical support and more information, see inside back cover or visit www.ti.com/powertrends Typical Characteristics PT6100 Series 1 Amp Adjustable Positive Step-down Integrated Switching Regulator PT6102, 3.3 VDC PT6101, 5.0 VDC (See Note 1) Efficiency vs Output Current Efficiency vs Output Current 100 90 Vin 80 9.0V 12.0V 70 15.0V 18.0V 26.0V 60 90 Vin 80 9.0V 12.0V 18.0V 24.0V 30.0V 38.0V 70 Efficiency - % Efficiency - % 90 (See Note 1) Efficiency vs Output Current 100 100 Efficiency - % PT6103, 12.0 VDC (See Note 1) 80 16.0V 20.0V 24.0V 70 30.0V 38.0V 60 60 50 50 40 40 50 0 0.2 0.4 0.6 0.8 0 1 0.2 0.4 0.6 0.8 1 40 0 Iout-(Amps) Ripple vs Output Current 180 80 160 26.0V 18.0V 50 15.0V 12.0V 40 350 300 120 100 38.0V 30.0V 80 24.0V 18.0V 12.0V 9.0V 250 38.0V 20 40 100 10 20 50 0 0 0.2 0.4 Iout-(Amps) Thermal Derating (Ta) 20.0V 16.0V 0 0 1 24.0V 150 60 0.8 30.0V 200 30 0.6 1 Vin 9.0V 0.4 0.8 400 Ripple-(mV) 60 0.6 Ripple vs Output Current 140 Vin Ripple-(mV) Ripple-(mV) 70 0.2 0.4 Iout-(Amps) Ripple vs Output Current 90 0 0.2 Iout-(Amps) 0.6 0.8 1 0 0.2 0.4 Iout-(Amps) Thermal Derating (Ta) (See Note 2) 0.6 0.8 1 Iout-(Amps) Thermal Derating (Ta) (See Note 2) (See Note 2) 50C 1 1 1 70C 70C 85C 0.4 0.2 85C Iout-(Amps) 0.6 0.6 0.4 12 15 18 21 24 27 Vin-(Volts) 85C 0.4 0 0 9 0.6 0.2 0.2 0 70C 0.8 0.8 Iout-(Amps) 0.8 Iout-(Amps) 60C 9 12 15 18 21 24 27 30 33 36 16 39 18 20 22 24 Vin-(Volts) (n Power Dissipation vs Output Current Power Dissipation vs Output Current 28 30 32 34 36 38 Power Dissipation vs Output Current 2 1.4 1 26 Vin-(Volts) 1.8 0.9 1.2 0.8 1.6 26.0V 0.6 18.0V 15.0V 0.5 12.0V 0.4 9.0V 0.3 Vin 1 38.0V 30.0V 24.0V 18.0V 12.0V 9.0V 0.8 0.6 PD-(Watts) PD-(Watts) 0.7 PD-(Watts) Vin Vin 1.4 38.0V 1.2 30.0V 24.0V 1 20.0V 0.8 16.0V 0.6 0.4 0.2 0.4 0.2 0.1 0.2 0 0 0.2 0.4 0.6 Iout-(Amps) 0.8 1 0 0 0 0.2 0.4 0.6 0.8 1 0 0.2 Iout-(Amps) 0.4 0.6 0.8 1 Iout-(Amps) Note 1: All data listed in the above graphs, except for derating data, has been developed from actual products tested at 25C. This data is considered typical data for the ISR. Note 2: Thermal derating graphs are developed in free air convection cooling of 40-60 LFM. (See Thermal Application Notes.) For technical support and more information, see inside back cover or visit www.ti.com/powertrends Application Notes PT6100/6210/6300 Series Adjusting the Output Voltage of Power Trends' Wide Input Range Bus ISRs The output voltage of the Power Trends' Wide Input Range Series ISRs may be adjusted higher or lower than the factory trimmed pre-set voltage with the addition of a single external resistor. Table 1 accordingly gives the allowable adjustment range for each model for either series as Va (min) and Va (max). Adjust Up: An increase in the output voltage is obtained by adding a resistor R2, between pin 12 (Vo adjust) and pins 5-8 (GND). Figure 1 2,3,4 Vin PT6100/6200/6300 Vin Vo GND 9,10,11 Vo Vo(adj) 5,6,7,8 12 (R1) Adj Down C1 1F Ceramic (Optional) C2 + 100F (Req'd) R2 Adjust Up COM COM Adjust Down: Add a resistor (R1), between pin 12 (Vo adjust) and pins 9-11(Vout). Refer to Figure 1 and Table 2 for both the placement and value of the required resistor; either (R1) or R2 as appropriate. Notes: 1. Use only a single 1% resistor in either the (R1) or R2 location. Place the resistor as close to the ISR as possible. 2. Never connect capacitors from Vo adjust to either GND or Vout. Any capacitance added to the Vo adjust pin will affect the stability of the ISR. 3. Adjustments to the output voltage may place additional limits on the maximum and minimum input voltage for the part. The revised maximum and minimum input voltage limits must comply with the following requirements. Note that the minimum input voltage limits are also model dependant. Vin (max) = (8 x Va)V or *30/38V, whichever is less. The values of (R1) [adjust down], and R2 [adjust up], can also be calculated using the following formulae. (R1) = Ro (Va - 1.25) Vo - Va k R2 = 1.25 Ro Va - Vo k Where: Vo = Original output voltage Va = Adjusted output voltage Ro = The resistance value fromTable 1 * Limit is 30V when inhibit function is active. Table 1 ISR ADJUSTMENT RANGE AND FORMULA PARAMETERS PT6x0x/PT6x1x series: 1Adc Rated 2Adc Rated 3Adc Rated Vin (min) = (Va + 4)V or 9V, whichever is greater. PT6x2x series: Vo <10V; Vin (min) = (Va + 2.0)V or 7.0V, whichever is greater. Vo 10V; Vin (min) = (Va + 2.5)V PT6102 PT6213 PT6303 PT6101 Vo (nom) Va (min) 3.3 1.89 Va (max) ) Ro (k For technical support and more information, see inside back cover or visit www.ti.com/powertrends PT6212 PT6302 PT6103 PT6214 PT6304 5.0 5.0 12.0 1.88 2.18 2.43 6.07 11.25 8.5 22.12 66.5 150.0 90.9 243.0 Application Notes continued PT6100/6210/6300 Series Table 2 ISR ADJUSTMENT RESISTOR VALUES 1Adc Rated 2Adc Rated 3Adc Rated Vo (nom) Va (req.d) PT6102 PT6213 PT6303 3.3 PT6101 1.9 (30.9)k 2.0 (38.4)k 2.1 ISR ADJUSTMENT RESISTOR VALUES (Cont) PT6103 PT6214 PT6304 12.0 1Adc Rated 2Adc Rated 3Adc Rated Vo (nom) Va (req.d) PT6101 5.0 PT6212 PT6302 5.0 PT6103 PT6214 PT6304 12.0 (31.5)k (37.5)k 6.2 156.0k 94.7k (207.0)k 6.4 134.0k 81.2k (47.1)k (44.0)k (223.0)k 6.6 117.0k 71.0k 2.2 (57.4)k (50.9)k (241.0)k (30.8)k 6.8 104.0k 63.1k 2.3 (69.8)k (259.0)k (58.3)k (35.4)k 7.0 93.8k 56.8k 2.4 (279.0)k (85.0)k (66.3)k (40.2)k 7.2 85.2k 51.6k (301.0)k 2.5 (104.0)k (75.0)k (45.5)k (32.0)k 7.4 78.1k 47.3k (325.0)k 2.6 (128.0)k (84.4)k (51.1)k (34.9)k 7.6 72.1k 43.7k (351.0)k 2.7 (161.0)k (94.6)k (57.3)k (37.9)k 7.8 67.0k 40.6k (379.0)k 2.8 (206.0)k (106.0)k (64.0)k (40.9)k 8.0 62.5k 37.9k (410.0)k 2.9 (274.0k (118.0)k (71.4)k (44.1)k 8.2 58.6k 35.5k (444.0)k 3.0 (388.0)k (131.0)k (79.5)k (47.3)k 8.4 55.1k 33.4k (483.0)k 3.1 (615.0)k (146.0)k (88.5)k (50.5)k 8.6 52.1k (525.0)k 3.2 (1300.0)k (163.0)k (98.5)k (53.8)k 8.8 49.3k (573.0)k (181.0)k (110.0)k (57.3)k 9.0 46.9k (628.0)k 3.3 5.0 PT6212 PT6302 5.0 3.4 831.0k (202.0)k (122.0)k (60.8)k 9.5 41.7k (802.0)k 3.5 416.0k (225.0)k (136.0)k (64.3)k 10.0 37.5k (1060.0)k 3.6 227.0k (252.0)k (153.0)k (68.0)k 10.5 34.1k (1500.0)k 3.7 208.0k (283.0)k (171.0)k (71.7)k 11.0 31.3k 3.8 166.0k (319.0)k (193.0)k (75.6)k 11.5 3.9 139.0k (361.0)k (219.0)k (79.5)k 12.0 4.0 119.0k (413.0)k (250.0)k (83.5)k 12.5 608.0k 4.1 104.0k (475.0)k (288.0)k (87.7)k 13.0 304.0k 4.2 92.4k (533.0)k (335.0)k (91.9)k 13.5 203.0k 4.3 83.1k (654.0)k (396.0)k (96.3)k 14.0 152.0k 4.4 75.6k (788.0)k (477.0)k (101.0)k 14.5 122.0k 4.5 69.3k (975.0)k (591.0)k (105.0)k 15.0 101.0k 4.6 63.9k (1260.0)k (761.0)k (110.0)k 15.5 86.8k 4.7 59.4k (1730.0)k (1050.0)k (115.0)k 16.0 75.9k 4.8 55.4k (1610.0)k (120.0)k 16.5 67.5k 4.9 52.0k (125.0)k 17.0 60.8k 5.0 48.9k (130.0)k 17.5 55.2k 5.1 46.2k 1880.0k 1140.0k (136.0)k 18.0 50.6k 5.2 43.8k 937.0k 568.0k (141.0)k 18.5 46.7k 5.3 41.6k 625.0k 379.0k (147.0)k 19.0 43.4k 5.4 39.6k 469.0k 284.0k (153.0)k 19.5 40.5k 5.5 37.8k 375.0k 227.0k (159.0)k 20.0 38.0k 5.6 36.1k 313.0k 189.0k (165.0)k 20.5 35.7k 5.7 34.6k 268.0k 162.0k (172.0)k 21.5 33.8k 5.8 33.3k 234.0k 142.0k (178.0)k 21.5 32.0k 5.9 32.0k 208.0k 126.0k (185.0)k 22.0 30.4k 6.0 30.8k 188.0k 114.0k (192.0)k R1 = (Blue) R2 = Black For technical support and more information, see inside back cover or visit www.ti.com/powertrends Application Notes PT6100/6210/6300 Series Using the Inhibit Function on Power Trends' Wide Input Range Bus ISRs For applications requiring output voltage On/Off control, the 12pin ISR products incorporate an inhibit function. The function has uses in areas such as battery conservation, power-up sequencing, or any other application where the regulated output from the module is required to be switched off. The On/Off function is provided by the Pin 1 (Inhibit) control. The ISR functions normally with Pin 1 open-circuit, providing a regulated output whenever a valid source voltage is applied to Vin, (pins 2, 3, & 4). When a low-level2 ground signal is applied to Pin 1, the regulator output will be disabled. Figure 1 shows an application schematic, which details the typical use of the Inhibit function. Note the discrete transistor (Q1). The Inhibit control has its own internal pull-up with a maximum open-circuit voltage of 8.3VDC. Only devices with a true open-collector or open-drain output can be used to control this pin. A discrete bipolar transistor or MOSFET is recommended. Equation 1 may be used to determine the approximate current drawn by Q1 when the inhibit is active. Equation 1 Istby = Vin / 155k 20% Figure 1 2,3,4 V in PT6100/6210/6300 Vin Vo Inh* 1 C1, 1F (Optional) GND V out Vo(adj) 5,6,7,8 12 C2 100F Q1 BSS138 Inh 9,10,11 + COM COM Turn-On Time: The output of the ISR is enabled automatically when external power is applied to the input. The Inhibit control pin is pulled high by its internal pull-up resistor. The ISR produces a fully regulated output voltage within 1-msec of either the release of the Inhibit control pin, or the application of power. The actual turn-on time will vary with the input voltage, output load, and the total amount of capacitance connected to the output Using the circuit of Figure 1, Figure 2 shows the typical rise in output voltage for the PT6101 following the turn-off of Q1 at time t =0. The waveform was measured with a 9Vdc input voltage, and 5-Ohm resistive load. Figure 2 6 5 4 Vo (Vdc) Notes: 1. The Inhibit control logic is similar for all Power Trends' modules, but the flexibility and threshold tolerances will be different. For specific information on the inhibit function of other ISR models, consult the applicable application note. 2. Use only a true open-collector device (preferably a discrete transistor) for the Inhibit input. Do Not use a pull-up resistor, or drive the input directly from the output of a TTL or other logic gate. To disable the output voltage, the control pin should be pulled low to less than +1.5VDC. 3. When the Inhibit control pin is active, i.e. pulled low, the maximum allowed input voltage is limited to +30Vdc. 4. Do not control the Inhibit input with an external DC voltage. This will lead to erratic operation of the ISR and may over-stress the regulator. 5. Avoid capacitance greater than 500pF at the Inhibit control pin. Excessive capacitance at this pin will cause the ISR to produce a pulse on the output voltage bus at turn-on. 6. Keep the On/Off transition to less than 10s. This prevents erratic operation of the ISR, which can cause a momentary high output voltage. 3 2 1 0 -0.2 For technical support and more information, see inside back cover or visit www.ti.com/powertrends 0 0.2 0.4 t (milli-secs) 0.6 0.8 1 PACKAGE OPTION ADDENDUM www.ti.com 28-Aug-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) PT6101A NRND SIP MODULE EBA 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type Samples Not Available PT6101C NRND SIP MODULE EBC 12 12 Pb-Free (RoHS) Call TI Level-1-215C-UNLIM Samples Not Available NRND 12 PT6101G SIP MODULE EBG 12 Pb-Free (RoHS) Call TI N / A for Pkg Type Samples Not Available PT6101H OBSOLETE SIP MODULE EBH 12 TBD Call TI Call TI Samples Not Available PT6101J OBSOLETE SIP MODULE EBJ 12 TBD Call TI Call TI Samples Not Available SIP MODULE EBD 12 Pb-Free (RoHS) Call TI N / A for Pkg Type Samples Not Available OBSOLETE SIP MODULE EBF 12 TBD Call TI Call TI Samples Not Available PT6101N PT6101S NRND 12 PT6102A NRND SIP MODULE EBA 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type Samples Not Available PT6102C NRND SIP MODULE EBC 12 12 Pb-Free (RoHS) Call TI Level-1-215C-UNLIM Samples Not Available PT6102N NRND SIP MODULE EBD 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type Samples Not Available PT6103A NRND SIP MODULE EBA 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type Samples Not Available PT6103C NRND SIP MODULE EBC 12 12 Pb-Free (RoHS) Call TI Level-1-215C-UNLIM Samples Not Available PT6103N NRND SIP MODULE EBD 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type Samples Not Available NRND SIP MODULE EBE 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type Samples Not Available OBSOLETE SIP MODULE EBF 12 TBD Call TI Call TI Samples Not Available PT6103R PT6103S (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 28-Aug-2010 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP(R) Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee(R) Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2010, Texas Instruments Incorporated