SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 D D D D D D SN54ABT8245 . . . JT PACKAGE SN74ABT8245 . . . DW PACKAGE (TOP VIEW) Members of the Texas Instruments SCOPE Family of Testability Products Compatible With the IEEE Standard 1149.1-1990 (JTAG) Test Access Port and Boundary-Scan Architecture Functionally Equivalent to 'F245 and 'ABT245 in the Normal-Function Mode SCOPE Instruction Set: - IEEE Standard 1149.1-1990 Required Instructions, Optional INTEST, CLAMP, and HIGHZ - Parallel-Signature Analysis at Inputs With Masking Option - Pseudo-Random Pattern Generation From Outputs - Sample Inputs/Toggle Outputs - Binary Count From Outputs - Even-Parity Opcodes Two Boundary-Scan Cells per I/O for Greater Flexibility State-of-the-Art EPIC-B BiCMOS Design Significantly Reduces Power Dissipation Package Options Include Plastic Small-Outline Packages (DW), Ceramic Chip Carriers(FK), and Standard Ceramic DIPs (JT) DIR B1 B2 B3 B4 GND B5 B6 B7 B8 TDO TMS 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 OE A1 A2 A3 A4 A5 VCC A6 A7 A8 TDI TCK SN54ABT8245 . . . FK PACKAGE (TOP VIEW) A3 A4 A5 NC V CC A6 A7 D A2 A1 OE NC DIR B1 B2 description 4 3 2 1 28 27 26 25 6 24 7 23 8 22 9 21 10 20 11 19 12 13 14 15 16 17 18 A8 TDI TCK NC TMS TDO B8 B3 B4 GND NC B5 B6 B7 The 'ABT8245 scan test devices with octal bus transceivers are members of the Texas Instruments SCOPE testability integrated-circuit family. This family of devices supports IEEE Standard 1149.1-1990 boundary scan to facilitate testing of complex circuit-board assemblies. Scan access to the test circuitry is accomplished via the 4-wire test access port (TAP) interface. 5 NC - No internal connection In the normal mode, these devices are functionally equivalent to the 'F245 and 'ABT245 octal bus transceivers. The test circuitry can be activated by the TAP to take snapshot samples of the data appearing at the device pins or to perform a self test on the boundary-test cells. Activating the TAP in normal mode does not affect the functional operation of the SCOPE octal bus transceivers. Data flow is controlled by the direction-control (DIR) and output-enable (OE) inputs. Data transmission is allowed from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at DIR. The output-enable (OE) input can be used to disable the device so that the buses are effectively isolated. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. SCOPE and EPIC-B are trademarks of Texas Instruments Incorporated. Copyright 1996, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 description (continued) In the test mode, the normal operation of the SCOPE bus transceivers is inhibited and the test circuitry is enabled to observe and control the I/O boundary of the device. When enabled, the test circuitry can perform boundary-scan test operations as described in IEEE Standard 1149.1-1990. Four dedicated test pins control the operation of the test circuitry: test data input (TDI), test data output (TDO), test mode select (TMS), and test clock (TCK). Additionally, the test circuitry performs other testing functions such as parallel-signature analysis (PSA) on data inputs and pseudo-random pattern generation (PRPG) from data outputs. All testing and scan operations are synchronized to the TAP interface. The SN54ABT8245 is characterized for operation over the full military temperature range of - 55C to 125C. The SN74ABT8245 is characterized for operation from - 40C to 85C. FUNCTION TABLE (normal mode) INPUTS 2 OPERATION OE DIR L L B data to A bus L H A data to B bus H X Isolation POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 functional block diagram Boundary-Scan Register OE DIR A1 24 1 2 23 B1 One of Eight Channels Bypass Register Boundary-Control Register VCC TDI 11 14 TDO Instruction Register VCC TMS TCK 12 13 TAP Controller Pin numbers shown are for the DW and JT packages. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 Terminal Functions TERMINAL NAME 4 DESCRIPTION A1 - A8 Normal-function A-bus I/O ports. See function table for normal-mode logic. B1 - B8 Normal-function B-bus I/O ports. See function table for normal-mode logic. DIR Normal-function direction-control input. See function table for normal-mode logic. GND Ground OE Normal-function output-enable input. See function table for normal-mode logic. TCK Test clock. One of four terminals required by IEEE Standard 1149.1-1990. Test operations of the device are synchronous to TCK. Data is captured on the rising edge of TCK and outputs change on the falling edge of TCK. TDI Test data input. One of four terminals required by IEEE Standard 1149.1-1990. TDI is the serial input for shifting data through the instruction register or selected data register. An internal pullup forces TDI to a high level if left unconnected. TDO Test data output. One of four terminals required by IEEE Standard 1149.1-1990. TDO is the serial output for shifting data through the instruction register or selected data register. TMS Test mode select. One of four terminals required by IEEE Standard 1149.1-1990. TMS input directs the device through its TAP controller states. An internal pullup forces TMS to a high level if left unconnected. VCC Supply voltage POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 test architecture Serial-test information is conveyed by means of a 4-wire test bus or TAP that conforms to IEEE Standard 1149.1-1990. Test instructions, test data, and test control signals all are passed along this serial-test bus. The TAP controller monitors two signals from the test bus, TCK and TMS. The TAP controller extracts the synchronization (TCK) and state control (TMS) signals from the test bus and generates the appropriate on-chip control signals for the test structures in the device. Figure 1 shows the TAP-controller state diagram. The TAP controller is fully synchronous to the TCK signal. Input data is captured on the rising edge of TCK and output data changes on the falling edge of TCK. This scheme ensures data to be captured is valid for fully one-half of the TCK cycle. The functional block diagram shows the IEEE Standard 1149.1-1990 4-wire test bus and boundary-scan architecture and the relationship among the test bus, the TAP controller, and the test registers. As illustrated, the device contains an 8-bit instruction register and three test-data registers: a 36-bit boundary-scan register, an 11-bit boundary-control register, and a 1-bit bypass register. Test-Logic-Reset TMS = H TMS = L TMS = H TMS = H Run-Test/Idle TMS = H Select-DR-Scan Select-IR-Scan TMS = L TMS = L TMS = L TMS = H TMS = H Capture-DR Capture-IR TMS = L TMS = L Shift-DR Shift-IR TMS = L TMS = L TMS = H TMS = H TMS = H TMS = H Exit1-DR Exit1-IR TMS = L TMS = L Pause-DR Pause-IR TMS = L TMS = L TMS = H TMS = H TMS = L Exit2-DR TMS = L Exit2-IR TMS = H Update-DR TMS = H TMS = L TMS = H Update-IR TMS = H TMS = L Figure 1. TAP-Controller State Diagram POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 state diagram description The TAP controller is a synchronous finite state machine that provides test control signals throughout the device. The state diagram shown in Figure 1 is in accordance with IEEE Standard 1149.1-1990. The TAP controller proceeds through its states based on the level of TMS at the rising edge of TCK. As illustrated, the TAP controller consists of 16 states. There are six stable states (indicated by a looping arrow in the state diagram) and ten unstable states. A stable state is a state the TAP controller can retain for consecutive TCK cycles. Any state that does not meet this criterion is an unstable state. There are two main paths through the state diagram: one to access and control the selected data register and one to access and control the instruction register. Only one register can be accessed at a time. Test-Logic-Reset The device powers up in the Test-Logic-Reset state. In the stable Test-Logic-Reset state, the test logic is reset and is disabled so that the normal logic function of the device is performed. The instruction register is reset to an opcode that selects the optional IDCODE instruction, if supported, or the BYPASS instruction. Certain data registers also can be reset to their power-up values. The state machine is constructed such that the TAP controller returns to the Test-Logic-Reset state in no more than five TCK cycles if TMS is left high. The TMS pin has an internal pullup resistor that forces it high if left unconnected or if a board defect causes it to be open circuited. For the 'ABT8245, the instruction register is reset to the binary value 11111111, which selects the BYPASS instruction. Each bit in the boundary-scan register is reset to logic 0. The boundary-control register is reset to the binary value 00000000010, which selects the PSA test operation with no input masking. Run-Test/Idle The TAP controller must pass through the Run-Test/Idle state (from Test-Logic-Reset) before executing any test operations. The Run-Test/Idle state can also be entered following data-register or instruction-register scans. Run-Test/Idle is a stable state in which the test logic can be actively running a test or can be idle. The test operations selected by the boundary-control register are performed while the TAP controller is in the Run-Test/Idle state. Select-DR-Scan, Select-lR-Scan No specific function is performed in the Select-DR-Scan and Select-lR-Scan states, and the TAP controller exits either of these states on the next TCK cycle. These states allow the selection of either data-register scan or instruction-register scan. Capture-DR When a data register scan is selected, the TAP controller must pass through the Capture-DR state. In the Capture-DR state, the selected data register can capture a data value as specified by the current instruction. Such capture operations occur on the rising edge of TCK, upon which the TAP controller exits the Capture-DR state. Shift-DR Upon entry to the Shift-DR state, the data register is placed in the scan path between TDI and TDO and, on the first falling edge of TCK, TDO goes from the high-impedance state to an active state. TDO enables to the logic level present in the least-significant bit of the selected data register. While in the stable Shift-DR state, data is serially shifted through the selected data register on each TCK cycle. The first shift occurs on the first rising edge of TCK after entry to the Shift-DR state (i.e., no shifting occurs during the TCK cycle in which the TAP controller changes from Capture-DR to Shift-DR or from Exit2-DR to Shift-DR). The last shift occurs on the rising edge of TCK, upon which the TAP controller exits the Shift-DR state. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 Exit1-DR, Exit2-DR The Exit1-DR and Exit2-DR states are temporary states end a data-register scan. It is possible to return to the Shift-DR state from either Exit1-DR or Exit2-DR without recapturing the data register. On the first falling edge of TCK after entry to Exit1-DR, TDO goes from the active state to the high-impedance state. Pause-DR No specific function is performed in the stable Pause-DR state, in which the TAP controller can remain indefinitely. The Pause-DR state suspends and resumes data-register scan operations without loss of data. Update-DR If the current instruction calls for the selected data register to be updated with current data, then such update occurs on the falling edge of TCK following entry to the Update-DR state. Capture-IR When an instruction-register scan is selected, the TAP controller must pass through the Capture-IR state. In the Capture-IR state, the instruction register captures its current status value. This capture operation occurs on the rising edge of TCK, upon which the TAP controller exits the Capture-IR state. For the 'ABT8245, the status value loaded in the Capture-IR state is the fixed binary value 10000001. Shift-IR Upon entry to the Shift-IR state, the instruction register is placed in the scan path between TDI and TDO and, on the first falling edge of TCK, TDO goes from the high-impedance state to an active state. TDO enables to the logic level present in the least-significant bit of the instruction register. While in the stable Shift-IR state, instruction data is serially shifted through the instruction register on each TCK cycle. The first shift occurs on the first rising edge of TCK after entry to the Shift-IR state (i.e., no shifting occurs during the TCK cycle in which the TAP controller changes from Capture-IR to Shift-IR or from Exit2-IR to Shift-IR). The last shift occurs on the rising edge of TCK, upon which the TAP controller exits the Shift-IR state. Exit1-IR, Exit2-IR The Exit1-IR and Exit2-IR states are temporary states that end an instruction-register scan. It is possible to return to the Shift-IR state from either Exit1-IR or Exit2-IR without recapturing the instruction register. On the first falling edge of TCK after entry to Exit1-IR, TDO goes from the active state to the high-impedance state. Pause-IR No specific function is performed in the stable Pause-IR state, in which the TAP controller can remain indefinitely. The Pause-IR state suspends and resumes instruction-register scan operations without loss of data. Update-IR The current instruction is updated and takes effect on the falling edge of TCK following entry to the Update-IR state. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 register overview With the exception of the bypass register, any test register can be thought of as a serial-shift register with a shadow latch on each bit. The bypass register differs in that it contains only a shift register. During the appropriate capture state (Capture-IR for instruction register, Capture-DR for data registers), the shift register can be parallel loaded from a source specified by the current instruction. During the appropriate shift state (Shift-IR or Shift-DR), the contents of the shift register are shifted out from TDO while new contents are shifted in at TDI. During the appropriate update state (Update-IR or Update-DR), the shadow latches are updated from the shift register. instruction register description The instruction register (IR) is eight bits long and tells the device what instruction is to be executed. Information contained in the instruction includes the mode of operation (either normal mode, in which the device performs its normal logic function, or test mode, in which the normal logic function is inhibited or altered), the test operation to be performed, which of the three data registers is to be selected for inclusion in the scan path during data-register scans, and the source of data to be captured into the selected data register during Capture-DR. Table 3 lists the instructions supported by the 'ABT8245. The even-parity feature specified for SCOPE devices is supported in this device. Bit 7 of the instruction opcode is the parity bit. Any instructions that are defined for SCOPE devices but are not supported by this device default to BYPASS. During Capture-IR, the IR captures the binary value 10000001. As an instruction is shifted in, this value is shifted out via TDO and can be inspected as verification that the IR is in the scan path. During Update-IR, the value that has been shifted into the IR is loaded into shadow latches. At this time, the current instruction is updated, and any specified mode change takes effect. At power up or in the Test-Logic-Reset state, the IR is reset to the binary value 11111111, which selects the BYPASS instruction. The IR order of scan is shown in Figure 2. TDI Bit 7 Parity (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Figure 2. Instruction Register Order of Scan 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Bit 1 Bit 0 (LSB) TDO SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 data register description boundary-scan register The boundary-scan register (BSR) is 36 bits long. It contains one boundary-scan cell (BSC) for each normal-function input pin, two BSCs for each normal-function I/O pin (one for input data and one for output data), and one BSC for each of the internally decoded output-enable signals (OEA and OEB). The BSR is used 1) to store test data that is to be applied internally to the inputs of the normal on-chip logic and/or externally to the device output pins, and/or 2) to capture data that appears internally at the outputs of the normal on-chip logic and/or externally at the device input pins. The source of data to be captured into the BSR during Capture-DR is determined by the current instruction. The contents of the BSR can change during Run-Test / Idle as determined by the current instruction. At power up or in Test-Logic-Reset, the value of each BSC is reset to logic 0. When external data is to be captured, the BSCs for signals OEA and OEB capture logic values determined by the following positive-logic equations: OEA = OE * DIR, and OEB = OE * DIR . When data is to be applied externally, these BSCs control the drive state (active or high-impedance) of their respective outputs. The BSR order of scan is from TDI through bits 35 - 0 to TDO. Table 1 shows the BSR bits and their associated device pin signals. Table 1. Boundary-Scan Register Configuration BSR BIT NUMBER DEVICE SIGNAL BSR BIT NUMBER DEVICE SIGNAL BSR BIT NUMBER DEVICE SIGNAL BSR BIT NUMBER DEVICE SIGNAL BSR BIT NUMBER DEVICE SIGNAL 35 OEB 31 B8-I 23 B8-O 15 A8-I 7 A8-O 34 OEA 30 B7-I 22 B7-O 14 A7-I 6 A7-O 33 DIR 29 B6-I 21 B6-O 13 A6-I 5 A6-O 32 OE 28 B5-I 20 B5-O 12 A5-I 4 A5-O -- -- 27 B4-I 19 B4-O 11 A4-I 3 A4-O -- -- 26 B3-I 18 B3-O 10 A3-I 2 A3-O -- -- 25 B2-I 17 B2-O 9 A2-I 1 A2-O -- -- 24 B1-I 16 B1-O 8 A1-I 0 A1-O POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 boundary-control register The boundary-control register (BCR) is 11 bits long. The BCR is used in the context of the RUNT instruction to implement additional test operations not included in the basic SCOPE instruction set. Such operations include PRPG, PSA with input masking, and binary count up (COUNT). Table 4 shows the test operations decoded by the BCR. During Capture-DR, the contents of the BCR are not changed. At power up or in Test-Logic-Reset, the BCR is reset to the binary value 00000000010, which selects the PSA test operation with no input masking. The BCR order of scan is from TDI through bits 10 - 0 to TDO. Table 2 shows the BCR bits and their associated test control signals. Table 2. Boundary-Control Register Configuration BCR BIT NUMBER TEST CONTROL SIGNAL BCR BIT NUMBER TEST CONTROL SIGNAL BCR BIT NUMBER TEST CONTROL SIGNAL 10 MASK8 6 MASK4 2 OPCODE2 9 MASK7 5 MASK3 1 OPCODE1 8 MASK6 4 MASK2 0 OPCODE0 7 MASK5 3 MASK1 -- -- bypass register The bypass register is a 1-bit scan path that can be selected to shorten the length of the system scan path, thereby reducing the number of bits per test pattern that must be applied to complete a test operation. During Capture-DR, the bypass register captures a logic 0. The bypass register order of scan is shown in Figure 3. TDI Bit 0 TDO Figure 3. Bypass Register Order of Scan 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 instruction-register opcode description The instruction-register opcodes are shown in Table 3. The following descriptions detail the operation of each instruction. Table 3. Instruction-Register Opcodes BINARY CODE BIT 7 BIT 0 MSB LSB SCOPE OPCODE DESCRIPTION SELECTED DATA REGISTER EXTEST/INTEST BYPASS Boundary scan Boundary scan Test 10000001 Bypass scan Bypass Normal 10000010 SAMPLE/PRELOAD Sample boundary Boundary scan Normal 00000011 Boundary scan Boundary scan Test 10000100 INTEST/EXTEST BYPASS Bypass scan Bypass Normal 00000101 BYPASS Bypass scan Bypass Normal 00000110 HIGHZ Control boundary to high impedance Bypass Modified test 10000111 CLAMP BYPASS Control boundary to 1/0 Bypass Test 10001000 Bypass scan Bypass Normal 00001001 RUNT Boundary run test Bypass Test 00001010 READBN Boundary read Boundary scan Normal 10001011 READBT Boundary read Boundary scan Test 00001100 CELLTST Boundary self test Boundary scan Normal 10001101 TOPHIP Boundary toggle outputs Bypass Test 10001110 SCANCN Boundary-control register scan Boundary control Normal 00001111 SCANCT Boundary-control register scan Boundary control Test All others BYPASS Bypass scan Bypass Normal 00000000 MODE Bit 7 is used to maintain even parity in the 8-bit instruction. The BYPASS instruction is executed in lieu of a SCOPE instruction that is not supported in the 'ABT8245. boundary scan This instruction conforms to the IEEE Standard 1149.1-1990 EXTEST and INTEST instructions. The BSR is selected in the scan path. Data appearing at the device input pins is captured in the input BSCs, while data appearing at the outputs of the normal on-chip logic is captured in the output BSCs. Data that has been scanned into the input BSCs is applied to the inputs of the normal on-chip logic, while data that has been scanned into the output BSCs is applied to the device output pins. The device operates in the test mode. bypass scan This instruction conforms to the IEEE Standard 1149.1-1990 BYPASS instruction. The bypass register is selected in the scan path. A logic 0 value is captured in the bypass register during Capture-DR. The device operates in the normal mode. sample boundary This instruction conforms to the IEEE Standard 1149.1-1990 SAMPLE/PRELOAD instruction. The BSR is selected in the scan path. Data appearing at the device input pins is captured in the input BSCs, while data appearing at the outputs of the normal on-chip logic is captured in the output BSCs. The device operates in the normal mode. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 control boundary to high impedance This instruction conforms to the IEEE Standard 1149.1a-1993 HIGHZ instruction. The bypass register is selected in the scan path. A logic 0 value is captured in the bypass register during Capture-DR. The device operates in a modified test mode in which all device I/O pins are placed in the high-impedance state, the device input pins remain operational, and the normal on-chip logic function is performed. control boundary to 1/0 This instruction conforms to the IEEE Standard 1149.1a-1993 CLAMP instruction. The bypass register is selected in the scan path. A logic 0 value is captured in the bypass register during Capture-DR. Data in the input BSCs is applied to the inputs of the normal on-chip logic, while data in the output BSCs is applied to the device output pins. The device operates in the test mode. boundary run test The bypass register is selected in the scan path. A logic 0 value is captured in the bypass register during Capture-DR. The device operates in the test mode. The test operation specified in the BCR is executed during Run-Test/Idle. The five test operations decoded by the BCR are: sample inputs/toggle outputs (TOPSIP), PRPG, PSA, simultaneous PSA and PRPG (PSA/PRPG), and simultaneous PSA and binary count up (PSA/COUNT). boundary read The BSR is selected in the scan path. The value in the BSR remains unchanged during Capture-DR. This instruction is useful for inspecting data after a PSA operation. boundary self test The BSR is selected in the scan path. All BSCs capture the inverse of their current values during Capture-DR. In this way, the contents of the shadow latches can be read out to verify the integrity of both shift-register and shadow-latch elements of the BSR. The device operates in the normal mode. boundary toggle outputs The bypass register is selected in the scan path. A logic 0 value is captured in the bypass register during Capture-DR. Data in the shift-register elements of the selected output BSCs is toggled on each rising edge of TCK in Run-Test/Idle, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK in Run-Test/Idle. Data in the selected input BSCs remains constant and is applied to the inputs of the normal on-chip logic. Data appearing at the device input pins is not captured in the input BSCs. The device operates in the test mode. boundary-control register scan The BCR is selected in the scan path. The value in the boundary-control register remains unchanged during Capture-DR. This operation must be performed before a boundary run test operation to specify which test operation is to be executed. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 boundary-control-register opcode description The BCR opcodes are decoded from BCR bits 2 - 0 as shown in Table 4. The selected test operation is performed while the RUNT instruction is executed in the Run-Test/Idle state. The following descriptions detail the operation of each BCR instruction and illustrate the associated PSA and PRPG algorithms. Table 4. Boundary-Control Register Opcodes BINARY CODE BIT 2 BIT 0 MSB LSB DESCRIPTION X00 Sample inputs/toggle outputs (TOPSIP) X01 Pseudo-random pattern generation/16-bit mode (PRPG) X10 Parallel-signature analysis/16-bit mode (PSA) 011 Simultaneous PSA and PRPG/8-bit mode (PSA/PRPG) 111 Simultaneous PSA and binary count up/8-bit mode (PSA/COUNT) It should be noted, in general, that while the control input BSCs (bits 35 - 32) are not included in the sample, toggle, PSA, PRPG, or COUNT algorithms, the output-enable BSCs (bits 35 - 34 of the BSR) do control the drive state (active or high impedance) of the selected device output pins. It also should be noted that these BCR instructions are only valid when the device is operating in one direction of data flow (that is, OEA OEB). Otherwise, the bypass instruction is operated. PSA input masking Bits 10 - 3 of the BCR specify device input pins to be masked from PSA operations. Bit 10 selects masking for device input pin A8 during A-to-B data flow or for device input pin B8 during B-to-A data flow. Bit 3 selects masking for device input pins A1 or B1 during A-to-B or B-to-A data flow, respectively. Bits intermediate to 10 and 3 mask corresponding device input pins, in order, from most significant to least significant, as indicated in Table 3. When the mask bit that corresponds to a particular device input has a logic 1 value, the device input pin is masked from any PSA operation, meaning that the state of the device input pin is ignored and has no effect on the generated signature. Otherwise, when a mask bit has a logic 0 value, the corresponding device input is not masked from the PSA operation. sample inputs/toggle outputs (TOPSIP) Data appearing at the selected device input pins is captured in the shift-register elements of the selected BSCs on each rising edge of TCK. This data is updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. Data in the shift-register elements of the selected output BSCs is toggled on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 pseudo-random pattern generation (PRPG) A pseudo-random pattern is generated in the shift-register elements of the selected BSCs on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK. This data also is updated in the shadow latches of the selected input BSCs and, thereby, applied to the inputs of the normal on-chip logic. Figures 4 and 5 illustrate the 16-bit linear-feedback shift-register algorithms through which the patterns are generated. An initial seed value should be scanned into the BSR before performing this operation. Note that a seed value of all zeroes does not produce additional patterns. A8-I A7-I A6-I A5-I A4-I A3-I A2-I A1-I B8-O B7-O B6-O B5-O B4-O B3-O B2-O B1-O = Figure 4. 16-Bit PRPG Configuration (OEA = 0, OEB = 1) B8-I B7-I B6-I B5-I B4-I B3-I B2-I B1-I A8-O A7-O A6-O A5-O A4-O A3-O A2-O A1-O = Figure 5. 16-Bit PRPG Configuration (OEA = 1, OEB = 0) 14 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 parallel-signature analysis (PSA) MASKX Data appearing at the selected device input pins is compressed into a 16-bit parallel signature in the shift-register elements of the selected BSCs on each rising edge of TCK. This data is then updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. Data in the shadow latches of the selected output BSCs remains constant and is applied to the device outputs. Figures 6 and 7 illustrate the 16-bit linear-feedback shift-register algorithms through which the signature is generated. An initial seed value should be scanned into the BSR before performing this operation. A8-I A7-I A6-I A5-I A4-I A3-I A2-I A1-I B8-O B7-O B6-O B5-O B4-O B3-O B2-O B1-O = = MASKX Figure 6. 16-Bit PSA Configuration (OEA = 0, OEB = 1) B8-I B7-I B6-I B5-I B4-I B3-I B2-I B1-I A8-O A7-O A6-O A5-O A4-O A3-O A2-O A1-O = = Figure 7. 16-Bit PSA Configuration (OEA = 1, OEB = 0) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 simultaneous PSA and PRPG (PSA/PRPG) Data appearing at the selected device input pins is compressed into an 8-bit parallel signature in the shift-register elements of the selected input BSCs on each rising edge of TCK. This data is then updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. At the same time, an 8-bit pseudo-random pattern is generated in the shift-register elements of the selected output BSCs on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK. Figures 8 and 9 illustrate the 8-bit linear-feedback shift-register algorithms through which the signature and patterns are generated. An initial seed value should be scanned into the BSR before performing this operation. Note that a seed value of all zeroes does not produce additional patterns. A7-I A6-I A5-I A4-I A3-I A2-I A1-I B8-O B7-O B6-O B5-O B4-O B3-O B2-O B1-O MASKX A8-I = = Figure 8. 8-Bit PSA/PRPG Configuration (OEA = 0, OEB = 1) B7-I B6-I B5-I B4-I B3-I B2-I B1-I A8-O A7-O A6-O A5-O A4-O A3-O A2-O A1-O MASKX B8-I = = Figure 9. 8-Bit PSA/PRPG Configuration (OEA = 1, OEB = 0) 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 simultaneous PSA and binary count up (PSA/COUNT) Data appearing at the selected device input pins is compressed into an 8-bit parallel signature in the shift-register elements of the selected input BSCs on each rising edge of TCK. This data is then updated in the shadow latches of the selected input BSCs and applied to the inputs of the normal on-chip logic. At the same time, an 8-bit binary count-up pattern is generated in the shift-register elements of the selected output BSCs on each rising edge of TCK, updated in the shadow latches, and applied to the associated device output pins on each falling edge of TCK. In addition, the shift-register elements of the opposite output BSCs are used to count carries out of the selected output BSCs and, thereby, extend the count to 16 bits. Figures 10 and 11 illustrate the 8-bit linear-feedback shift-register algorithms through which the signature is generated. An initial seed value should be scanned into the BSR before performing this operation. A7-I A6-I A5-I A4-I A3-I A2-I A1-I MASKX A8-I = MSB LSB = B8-O B7-O B6-O B5-O B4-O B3-O B2-O B1-O B2-I B1-I Figure 10. 8-Bit PSA/COUNT Configuration (OEA = 0, OEB = 1) B7-I B6-I B5-I B4-I B3-I MASKX B8-I = MSB LSB = A8-O A7-O A6-O A5-O A4-O A3-O A2-O A1-O Figure 11. 8-Bit PSA/COUNT Configuration (OEA = 1, OEB = 0) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 timing description All test operations of the 'ABT8245 are synchronous to TCK. Data on the TDI, TMS, and normal-function inputs is captured on the rising edge of TCK. Data appears on the TDO and normal-function output pins on the falling edge of TCK. The TAP controller is advanced through its states (as illustrated in Figure 1) by changing the value of TMS on the falling edge of TCK and then applying a rising edge to TCK. A simple timing example is shown in Figure 12. In this example, the TAP controller begins in the Test-Logic-Reset state and is advanced through its states as necessary to perform one instruction-register scan and one data-register scan. While in the Shift-IR and Shift-DR states, TDI is used to input serial data, and TDO is used to output serial data. The TAP controller is then returned to the Test-Logic-Reset state. Table 5 explains the operation of the test circuitry during each TCK cycle. Table 5. Explanation of Timing Example TCK CYCLE(S) TAP STATE AFTER TCK DESCRIPTION 1 Test-Logic-Reset TMS is changed to a logic 0 value on the falling edge of TCK to begin advancing the TAP controller toward the desired state. 2 Run-Test/Idle 3 Select-DR-Scan 4 Select-IR-Scan 5 Capture-IR The IR captures the 8-bit binary value 10000001 on the rising edge of TCK as the TAP controller exits the Capture-IR state. 6 Shift-IR TDO becomes active and TDI is made valid on the falling edge of TCK. The first bit is shifted into the TAP on the rising edge of TCK as the TAP controller advances to the next state. Shift-IR One bit is shifted into the IR on each TCK rising edge. With TDI held at a logic 1 value, the 8-bit binary value 11111111 is serially scanned into the IR. At the same time, the 8-bit binary value 10000001 is serially scanned out of the IR via TDO. In TCK cycle 13, TMS is changed to a logic 1 value to end the IR scan on the next TCK cycle. The last bit of the instruction is shifted as the TAP controller advances from Shift-IR to Exit1-IR. 14 Exit1-IR TDO becomes inactive (goes to the high-impedance state) on the falling edge of TCK. 15 Update-IR 16 Select-DR-Scan 17 Capture-DR The bypass register captures a logic 0 value on the rising edge of TCK as the TAP controller exits the Capture-DR state. 18 Shift-DR TDO becomes active and TDI is made valid on the falling edge of TCK. The first bit is shifted into the TAP on the rising edge of TCK as the TAP controller advances to the next state. 19 - 20 Shift-DR The binary value 101 is shifted in via TDI, while the binary value 010 is shifted out via TDO. 21 Exit1-DR TDO becomes inactive (goes to the high-impedance state) on the falling edge of TCK. 22 Update-DR 23 Select-DR-Scan 7-13 18 24 Select-IR-Scan 25 Test-Logic-Reset The IR is updated with the new instruction (BYPASS) on the falling edge of TCK. In general, the selected data register is updated with the new data on the falling edge of TCK. Test operation completed POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Test-Logic-Reset Select-IR-Scan Select-DR-Scan Update-DR IIIIII IIIIII IIIIII IIIIII Exit1-DR Capture-DR Update-IR Select-DR-Scan II II IIIII IIIII IIIII IIIII Exit1-IR Shift-IR Capture-IR Select-IR-Scan TAP Controller State Select-DR-Scan TDO IIIIIIII IIIIIIII IIIIIIII IIIIIIII Run-Test/Idle TDI Test-Logic-Reset TMS Shift-DR TCK 3-State (TDO) or Don't Care (TDI) Figure 12. Timing Example absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 7 V Input voltage range, VI (except I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 7 V Input voltage range, VI (I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 5.5 V Voltage range applied to any output in the high state or power-off state, VO . . . . . . . . . . . . . - 0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT8245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT8245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 50 mA Maximum power dissipation at TA = 55C (in still air) (see Note 2): DW package . . . . . . . . . . . . . . . . . 1.7 W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings can be exceeded if the input and output clamp-current ratings are observed. 2. The maximum package power dissipation is calculated using a junction temperature of 150C and a board trace length of 750 mils. For more information, refer to the Package Thermal Considerations application note in the ABT Advanced BiCMOS Technology Data Book, literature number SCBD002. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 recommended operating conditions (see Note 3) SN54ABT8245 SN74ABT8245 MIN MAX MIN MAX 4.5 5.5 4.5 5.5 UNIT VCC VIH Supply voltage VIL VI Low-level input voltage IOH IOL High-level output current VCC - 24 Low-level output current 48 64 mA t /v Input transition rise or fall rate 10 10 ns / V 85 C High-level input voltage 2 2 0.8 Input voltage 0 TA Operating free-air temperature NOTE 3: Unused pins (input or I/O) must be held high or low to prevent them from floating. - 55 125 V 0.8 0 - 40 V VCC - 32 V V mA electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH VOL TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V, II = -18 mA IOH = - 3 mA VCC = 5 V, VCC = 4.5 V, SN54ABT8245 MIN -1.2 MAX SN74ABT8245 MIN -1.2 2.5 IOH = - 3 mA IOH = - 24 mA 3 3 3 2 2 VCC = 4.5 V, VCC = 4.5 V, IOH = - 32 mA IOL = 48 mA 2* VCC = 4.5 V, IOL = 64 mA VI = VCC VI = GND IOZH IOZL VCC = 5.5 V, VCC = 5.5 V, VO = 2.7 V VO = 0.5 V IOZPU IOZPD VCC = 0 to 2 V, VCC = 2 V or 0, VO = 0.5 V or 2.7 V VO = 0.5 V or 2.7 V Ioff ICEX IO VCC = 0, VCC = 5.5 V, VI or VO 4.5 V VO = 5.5 V Outputs high VCC = 5.5 V, VO = 2.5 V VCC = 5.5 V, IO = 0, VI = VCC or GND A or B orts ports A or B ports 0.55 0.55 1 1 100 100 100 TDI, TMS TDI, TMS 10 - 40 -160 10 - 40 -160 - 40 A A 50 50 50 A - 50 - 50 A 50 50 50 A 50 50 50 A 100 A 50 50 A mA 2 2 Outputs low 30 38 38 38 Outputs disabled 0.9 2 2 2 15 1.5 15 1.5 15 1.5 VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V Control inputs A or B ports - 50 50 2 Ci -180 -180 0.9 VCC = 5.5 V,, One input at 3.4 V,, Other inputs at VCC or GND - 50 POST OFFICE BOX 655303 mA mA 3 pF 10 pF Co VO = 2.5 V or 0.5 V TDO 8 * On products compliant to MIL-PRF-38535, this parameter does not apply. All typical values are at VCC = 5 V. The parameters IOZH and IOZL include the input leakage current. Not more than one output should be tested at a time, and the duration of the test should not exceed 1 second. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. 20 10 -180 ICC A -160 -100 Outputs high V - 50 100 - 50 V V 1 DIR, OE, TCK VCC = 5.5 V, VCC = 5.5 V, UNIT 2 0.55 0.55* IIH IIL MAX -1.2 2.5 VCC = 5.5 V,, VI = VCC or GND Cio TA = 25C TYP MAX 2.5 II ICC MIN * DALLAS, TEXAS 75265 pF SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (test mode) (see Figure 13) SN54ABT8245 fclock tw tsu th td tr SN74ABT8245 MIN MAX MIN MAX 50 0 50 Clock frequency TCK 0 Pulse duration TCK high or low 5 5 A or B or DIR or OE before TCK 7 5 Setup time Hold time Delay time UNIT MHz ns ns TDI before TCK 6 6 TMS before TCK 6 6 A or B or DIR or OE after TCK 0 0 TDI after TCK 0 0 TMS after TCK 0 0 50* 50 ns 1* 1 s Power up to TCK Rise time VCC power up * On products compliant to MIL-PRF-38535, this parameter is not production tested. ns switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (normal mode) (see Figure 13) SN54ABT8245 PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B B or A tPZH tPZL OE B or A tPHZ tPLZ OE B or A VCC = 5 V, TA = 25C MIN MAX MIN TYP MAX 2 3.5 4.6 2 5.8 2 3.4 4.5 2 5.5 2.5 4.5 5.8 2.5 6.9 3 5.2 6.6 3 8.1 3 6.1 7.6 3 8.9 3 5.5 6.9 3 8 UNIT ns ns ns switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (normal mode) (see Figure 13) SN74ABT8245 PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B B or A tPZH tPZL OE B or A tPHZ tPLZ OE B or A POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 VCC = 5 V, TA = 25C MIN MAX MIN TYP MAX 2 3.5 4.3 2 4.8 2 3.4 4.2 2 5.1 2.5 4.5 5.5 2.5 6.8 3 5.2 6 3 7.5 3 6.1 7.1 3 8.4 3 5.5 6.6 3 7.5 UNIT ns ns ns 21 SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (test mode) (see Figure 13) SN54ABT8245 PARAMETER fmax tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ FROM (INPUT) TO (OUTPUT) TCK TCK A or B TCK TDO TCK A or B TCK TDO TCK A or B TCK TDO VCC = 5 V, TA = 25C MIN TYP 50 90 MIN MAX UNIT MAX 50 MHz 3.5 8 9.5 3.5 12.5 3 7.7 9 3 12 2.5 4.3 5.5 2.5 7 2.5 4.2 5.5 2.5 7 4.5 8.2 9.8 4.5 12.5 4.5 9 10.5 4.5 13.5 2.5 4.3 5.5 2.5 7 2.5 4.9 6.3 2.5 7.8 3.5 8.4 11.2 3.5 14.2 3 8 10.5 3 13.5 2 5.9 7 2 9 3 5 6.5 3 8 ns ns ns ns ns ns switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (test mode) (see Figure 13) PARAMETER fmax tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ 22 FROM (INPUT) FROM (INPUT) TO (OUTPUT) TO (OUTPUT) TCK TCK A or B TCK TDO TCK A or B TCK TDO TCK A or B TCK TDO POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN74ABT8245 VCC = 5 V, TA = 25C MIN TYP MIN MAX UNIT MAX 50 90 3.5 8 9.5 3.5 50 12 MHz 3 7.7 9 3 11.5 2.5 4.3 5.5 2.5 6.5 2.5 4.2 5.5 2.5 6.5 4.5 8.2 9.5 4.5 12 4.5 9 10.5 4.5 13 2.5 4.3 5.5 2.5 6.5 2.5 4.9 6 2.5 7 3.5 8.4 10.5 3.5 13.5 3 8 10.5 3 13 3 5.9 7 3 8.5 3 5 6.5 3 7.5 ns ns ns ns ns ns SN54ABT8245, SN74ABT8245 SCAN TEST DEVICES WITH OCTAL BUS TRANSCEIVERS SCBS124D - AUGUST 1992 - REVISED DECEMBER 1996 PARAMETER MEASUREMENT INFORMATION 7V S1 500 From Output Under Test Open GND CL = 50 pF (see Note A) 500 TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open LOAD CIRCUIT 3V 1.5 V Timing Input 0V tw tsu 3V Input 1.5 V 3V 1.5 V Data Input 1.5 V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.5 V 0V tPHL 1.5 V 1.5 V VOL VOH Output 1.5 V 1.5 V 0V 1.5 V VOL tPLZ Output Waveform 1 S1 at 7 V (see Note B) tPLH tPHL 1.5 V tPZL VOH Output 3V Output Control 1.5 V tPLH 1.5 V 0V VOLTAGE WAVEFORMS PULSE DURATION Input th Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V tPZH 3.5 V VOL + 0.3 V VOL tPHZ 1.5 V VOH - 0.3 V VOH [0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 13. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) 5962-9318601M3A ACTIVE LCCC FK 28 1 TBD Call TI Call TI 5962-9318601MLA ACTIVE CDIP JT 24 1 TBD Call TI Call TI SN74ABT8245DW ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT8245DWE4 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT8245DWG4 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT8245DWR ACTIVE SOIC DW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT8245DWRE4 ACTIVE SOIC DW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT8245DWRG4 ACTIVE SOIC DW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNJ54ABT8245FK ACTIVE LCCC FK 28 1 TBD SNJ54ABT8245JT ACTIVE CDIP JT 24 1 TBD POST-PLATE N / A for Pkg Type A42 N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN54ABT8245, SN74ABT8245 : * Catalog: SN74ABT8245 * Military: SN54ABT8245 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74ABT8245DWR Package Package Pins Type Drawing SOIC DW 24 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 24.4 Pack Materials-Page 1 10.75 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 15.7 2.7 12.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74ABT8245DWR SOIC DW 24 2000 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA MCER004A - JANUARY 1995 - REVISED JANUARY 1997 JT (R-GDIP-T**) CERAMIC DUAL-IN-LINE 24 LEADS SHOWN PINS ** A 13 24 B 1 24 28 A MAX 1.280 (32,51) 1.460 (37,08) A MIN 1.240 (31,50) 1.440 (36,58) B MAX 0.300 (7,62) 0.291 (7,39) B MIN 0.245 (6,22) 0.285 (7,24) DIM 12 0.070 (1,78) 0.030 (0,76) 0.100 (2,54) MAX 0.320 (8,13) 0.290 (7,37) 0.015 (0,38) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0-15 0.014 (0,36) 0.008 (0,20) 0.100 (2,54) 4040110/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP3-T24, GDIP4-T28, and JEDEC MO-058 AA, MO-058 AB POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated