I N D U C T O R S September 2013 Inductors for Standard Circuits Multilayer Ferrite MLF-Jseries MLF1005-J MLF1608-J MLF2012-J 1005 [0402 inch]* 1608 [0603 inch] 2012 [0805 inch] * Dimensions Code JIS[EIA] (2/17) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (3/17) I N D U C T O R S Inductors for Standard Circuits Product compatible with RoHS directive Halogen-free Compatible with lead-free solders AEC-Q200 Multilayer Ferrite Overview of the MLF-J Series FEATURES Lineup includes world's smallest class 1005 size products compatible with J tolerance. APPLICATION Mobile devices such as smart phones, tablet terminals, and modules, matching circuits such as TV tuners, and FM tuners, filter circuits NFC (Near Field Communication) circuits, automotive equipment (MLF1608-J, MLF2012-J) PART NUMBER CONSTRUCTION MLF Series name 1005 LxWxH Dimensions (mm) 1005 1.0x0.5x0.5 1608 1.6x0.8x0.8 2.0x1.25x0.85 2012 2.0x1.25x1.25 V Characteristics A D E V G R15 J Inductance (H) R10 0.1 1R0 1 100 10 Inductance tolerance J 5% T Packaging style Internal code T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type Temperature range Operating Storage temperature temperature C C -55 to +125 -55 to +125 -55 to +125 -55 to +125 MLF1005-J MLF1608-J t=0.85 MLF2012-J -55 to +125 -55 to +125 t=1.25 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 10,000 4,000 4,000 2,000 mg 1.2 4 10 14 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (4/17) I N D U C T O R S Overview of the MLF-J Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 150C T2 180C Time t1 60 to 120s Soldering Temp. T3 230C Time t2 30 to 60s Peak Temp. Time T4 t3 250 to 260C 10s max. * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (5/17) I N D U C T O R S MLF-J series MLF1005-J Type 0.500.05 SHAPE & DIMENSIONS 0.10min. 0.10min. 0.500.05 1.000.05 Dimensions in mm 0.5 RECOMMENDED LAND PATTERN 0.5 0.4 0.5 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (6/17) I N D U C T O R S MLF-J series MLF1005-J Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Q L, Q measuring conditions (H) Tolerance min. typ. 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 10 10 15 15 15 15 15 15 15 15 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 50 50 55 55 55 60 60 60 60 60 Frequency (MHz) 25 25 25 25 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10 10 Current (mA) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Self-resonant frequency (MHz) DC resistance ( ) Rated current (mA) min. typ. max. typ. max. 450 400 350 320 290 260 230 210 190 170 210 190 170 150 130 120 110 100 90 80 880 800 650 600 450 450 380 330 300 250 600 460 450 360 320 290 230 200 180 150 0.51 0.59 0.63 0.72 0.79 0.91 1.05 1.35 1.50 1.95 0.41 0.42 0.47 0.55 0.59 0.64 0.79 0.95 1.05 1.30 0.33 0.33 0.39 0.40 0.47 0.65 0.80 0.89 0.95 1.35 0.24 0.25 0.34 0.43 0.43 0.45 0.55 0.68 0.75 0.99 180 180 180 160 160 150 140 130 120 120 50 50 45 45 40 40 35 35 30 30 Part No. MLF1005VR10JT MLF1005VR12JT MLF1005VR15JT MLF1005VR18JT MLF1005VR22JT MLF1005VR27JT MLF1005VR33JT MLF1005VR39JT MLF1005VR47JT MLF1005VR56JT MLF1005GR39JT MLF1005GR47JT MLF1005GR56JT MLF1005GR68JT MLF1005GR82JT MLF1005G1R0JT MLF1005G1R2JT MLF1005G1R5JT MLF1005G1R8JT MLF1005G2R2JT The " " of the Part Number contains the internal code. Measurement equipment Measurement item Product No. L, Q 4294A+16034G Self-resonant frequency E4991A DC resistance Type-7561 Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (7/17) I N D U C T O R S MLF-J series MLF1005-J Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 10 G1R8 G1R2 Inductance(H) 1 GR39 GR82 GR56 VR33 VR22 0.1 VR15 VR10 VR47 0.01 1 10 100 1000 Frequency(MHz) 10 G2R2 G1R5 Inductance(H) GR47 G1R0 1 GR68 VR39 VR27 VR18 VR12 0.1 VR56 0.01 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (8/17) I N D U C T O R S MLF-J series MLF1005-J Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 60 GR39 G1R2 VR10 50 VR22 GR56 G1R8 GR82 VR47 40 Q VR33 VR15 30 20 10 0 1 10 100 1000 Frequency(MHz) 70 G1R0 60 VR27 50 VR56 GR68 GR47 VR12 Q 40 VR18 G1R5 30 VR39 G2R2 20 10 0 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (9/17) I N D U C T O R S MLF-J series MLF1608-J Type 0.800.15 SHAPE & DIMENSIONS 0.300.20 0.300.20 0.800.15 1.600.15 Dimensions in mm 0.8 RECOMMENDED LAND PATTERN 0.6 0.8 0.6 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (10/17) I N D U C T O R S MLF-J series MLF1608-J Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L L, Q measuring conditions Q (H) Tolerance min. typ. 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 15 15 15 15 15 15 15 15 15 15 15 15 35 35 35 35 35 35 35 35 35 35 35 35 30 30 25 25 25 25 25 25 25 25 30 30 30 30 50 50 55 55 55 55 60 60 60 60 60 60 55 55 Frequency (MHz) 25 25 25 25 25 25 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10 4 4 4 2 2 Current (mA) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.1 0.1 0.1 0.1 0.1 Self-resonant frequency (MHz) DC resistance ( ) Rated current (mA) min. typ. max. typ. max. 450 400 350 320 290 260 230 210 190 170 150 130 120 110 100 90 80 70 65 60 55 45 40 35 30 25 600 550 500 450 400 350 320 290 260 230 210 190 170 150 140 130 120 110 100 90 80 70 60 55 50 45 0.35 0.40 0.45 0.50 0.55 0.60 0.75 0.85 0.95 1.05 1.25 1.40 0.50 0.65 0.70 0.85 1.00 1.15 1.30 1.45 1.60 1.10 1.30 1.50 1.70 1.80 0.20 0.20 0.25 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.65 0.75 0.25 0.25 0.30 0.35 0.45 0.50 0.55 0.65 0.75 0.55 0.65 0.80 1.00 1.20 200 200 200 150 150 150 100 100 100 100 70 70 50 50 50 50 30 30 30 30 30 15 15 10 10 10 Part No. MLF1608DR10JT MLF1608DR12JT MLF1608DR15JT MLF1608DR18JT MLF1608DR22JT MLF1608DR27JT MLF1608DR33JT MLF1608DR39JT MLF1608DR47JT MLF1608DR56JT MLF1608DR68JT MLF1608DR82JT MLF1608A1R0JT MLF1608A1R2JT MLF1608A1R5JT MLF1608A1R8JT MLF1608A2R2JT MLF1608A2R7JT MLF1608A3R3JT MLF1608A3R9JT MLF1608A4R7JT MLF1608E5R6JT MLF1608E6R8JT MLF1608E8R2JT MLF1608E100JT MLF1608E120JT The " " of the Part Number contains the internal code. Measurement equipment Measurement item Product No. L, Q 4294A+16034G Self-resonant frequency E4991A DC resistance Type-7561 Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (11/17) I N D U C T O R S MLF-J series MLF1608-J Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 E100 E6R8 10 A4R7 Inductance(H) A3R3 A2R2 A1R0 A1R5 1 DR68 DR47 DR33 DR22 DR15 DR10 0.1 0.01 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (12/17) I N D U C T O R S MLF-J series MLF1608-J Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 80 A3R3 E100 70 A1R5 60 A1R0 E6R8 DR22 A2R2 DR33 DR15 50 Q DR68 40 DR10 30 DR47 20 10 0 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (13/17) I N D U C T O R S MLF-J series MLF2012-J Type 1.250.20 SHAPE & DIMENSIONS 0.500.30 0.500.30 T 2.000.20 T 0.850.20 1.250.20 Dimensions in mm 1.2 RECOMMENDED LAND PATTERN 0.8 1.0 0.8 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (14/17) I N D U C T O R S MLF-J series MLF2012-J Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L, Q measuring conditions Thickness L T (mm) (H) Tolerance min. typ. 0.850.2 0.850.2 0.850.2 0.850.2 0.850.2 0.850.2 0.850.2 0.850.2 1.250.2 1.250.2 1.250.2 1.250.2 0.850.2 0.850.2 0.850.2 0.850.2 0.850.2 1.250.2 1.250.2 1.250.2 1.250.2 1.250.2 1.250.2 1.250.2 1.250.2 1.250.2 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 20 20 20 20 20 20 20 25 25 25 25 25 45 45 45 45 45 45 45 45 45 50 50 50 50 50 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 Q 30 30 30 30 30 30 30 35 35 35 35 35 55 55 60 60 60 70 70 70 70 75 75 75 75 75 Frequency (MHz) 25 25 25 25 25 25 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10 4 4 4 2 2 Current (mA) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.1 0.1 0.1 0.1 0.1 Self-resonant frequency (MHz) DC resistance ( ) Rated current (mA) min. typ. max. typ. max. 400 360 320 280 250 220 200 180 160 150 140 130 120 110 100 90 80 70 60 55 50 45 40 35 30 25 500 450 410 370 330 300 270 250 230 210 190 170 160 150 140 130 120 100 90 80 70 65 60 55 50 45 0.15 0.20 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.60 0.65 0.70 0.80 0.90 0.10 0.12 0.13 0.15 0.16 0.18 0.23 0.25 0.25 0.30 0.35 0.40 0.15 0.15 0.18 0.20 0.22 0.25 0.28 0.30 0.35 0.30 0.32 0.35 0.40 0.50 300 300 300 300 250 250 250 200 200 150 150 150 80 80 80 80 50 50 50 30 30 15 15 15 15 15 Part No. MLF2012DR10JT MLF2012DR12JT MLF2012DR15JT MLF2012DR18JT MLF2012DR22JT MLF2012DR27JT MLF2012DR33JT MLF2012DR39JT MLF2012DR47JT MLF2012DR56JT MLF2012DR68JT MLF2012DR82JT MLF2012A1R0JT MLF2012A1R2JT MLF2012A1R5JT MLF2012A1R8JT MLF2012A2R2JT MLF2012A2R7JT MLF2012A3R3JT MLF2012A3R9JT MLF2012A4R7JT MLF2012E5R6JT MLF2012E6R8JT MLF2012E8R2JT MLF2012E100JT MLF2012E120JT The " " of the Part Number contains the internal code. Measurement equipment Measurement item Product No. L, Q 4294A+16034G Self-resonant frequency E4991A DC resistance Type-7561 Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (15/17) I N D U C T O R S MLF-J series MLF2012-J Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 E100 10 A4R7 Inductance(H) E6R8 A1R0 1 A3R3 A2R2 A1R5 DR68 DR47 DR33 DR22 DR15 0.1 DR10 0.01 1 10 100 1000 Frequency(MHz) 100 E120 10 E8R2 A3R9 Inductance(H) E5R6 DR82 A2R7 A1R8 DR56 A1R2 1 DR39 DR27 DR18 0.1 DR12 0.01 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (16/17) I N D U C T O R S MLF-J series MLF2012-JType ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 90 A4R7 80 A3R3 70 A2R2 A1R5 E100 60 DR22 DR15 E6R8 DR33 Q 50 A1R0 40 DR47 DR10 30 DR68 20 10 0 1 10 100 1000 Frequency(MHz) 90 80 E5R6 E8R2 A3R9 A2R7 70 E120 60 Q DR18 DR39 A1R8 50 A1R2 DR12 40 DR82 30 DR56 20 DR27 10 0 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm (17/17) I N D U C T O R S MLF-J series Packaging Style REEL DIMENSIONS o60min. 1.0 2.00.5 8.4 +2.0 -0.0 o130.2 14.4max. o210.8 o1802.0 Dimensions in mm 3.50.05 Cavity Type MLF1005-J MLF1608-J t=0.85 MLF2012-J t=1.25 A 1.150.1 1.90.2 2.30.2 2.30.2 B 0.650.1 1.10.2 1.50.2 1.50.2 K 0.8 max. 1.1 max. 1.1 max. 1.5 max. A 8.00.3 Sprocket hole 1.5 +0.1 -0.0 1.750.1 TAPE DIMENSIONS K B 4.00.1 2.00.05 160min. Taping 2.00.05 200min. 300min. Drawing direction Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130929 / inductor_standard_mlf-j_en.fm Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TDK: MLF1608A3R3JTD25 MLF2012E8R2JTD25 MLF1608A2R2JTD25 MLF1608DR27JTD25 MLF1608DR47JTD25 MLF1608A3R9JTD25 MLF2012DR39JTD25 MLF2012A1R5JTD25 MLF2012DR12JTD25 MLF1608A2R7JTD25 MLF2012DR22JTD25 MLF1608A4R7JTD25 MLF1608DR82JTD25 MLF2012DR10JTD25 MLF2012DR33JTD25 MLF2012E120JTD25 MLF2012A2R7JTD25 MLF2012E100JTD25 MLF1608A1R0JTD25 MLF1608DR56JTD25 MLF2012E6R8JTD25 MLF2012A4R7JTD25 MLF1608DR15JTD25 MLF1608E100JTD25 MLF1608E120JTD25 MLF1608DR33JTD25 MLF2012DR47JTD25 MLF2012DR27JTD25 MLF1608DR39JTD25 MLF2012A1R8JTD25 MLF1608DR10JTD25 MLF2012A2R2JTD25 MLF1608DR12JTD25 MLF1608DR22JTD25 MLF2012A3R3JTD25 MLF1608A1R5JTD25 MLF1608A1R8JTD25 MLF2012DR15JTD25 MLF2012A1R0JTD25 MLF2012DR56JTD25 MLF1608DR18JTD25 MLF1608E8R2JTD25 MLF2012DR18JTD25 MLF2012DR68JTD25 MLF2012A3R9JTD25 MLF2012E5R6JTD25 MLF2012A1R2JTD25 MLF1608E6R8JTD25 MLF1608A1R2JTD25 MLF1608E5R6JTD25 MLF2012DR82JTD25 MLF1608DR68JTD25