INDUCTORS
MLF1005-J 1005 [0402 inch]*
MLF1608-J 1608 [0603 inch]
MLF2012-J 2012 [0805 inch]
* Dimensions Code JIS[EIA]
September 2013
Inductors for Standard Circuits
Multilayer Ferrite
MLF-Jseries
(2/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
Inductors for Standard Circuits
Multilayer Ferrite
FEATURES
Lineup includes world’s smallest class 1005 size products compatible with J tolerance.
APPLICATION
Mobile devices such as smart phones, tablet terminals, and modules, matching circuits such as TV tuners, and FM tuners, filter circuits
NFC (Near Field Communication) circuits, automotive equipment (MLF1608-J, MLF2012-J)
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
AEC-Q200
Overview of the MLF-J Series
MLF 1005 V R15 J T □□□
Series name L×W×H Dimensions Characteristics Inductance Inductance
tolerance Packaging style Internal code
(mm) (μH)
1005 1.0×0.5×0.5 A R10 0.1 J ±5% T Taping
1608 1.6×0.8×0.8 D 1R0 1
2012 2.0×1.25×0.85 E 100 10
2.0×1.25×1.25 V
G
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C）(pieces/reel) （mg）
MLF1005-J –55 to +125 –55 to +125 10,000 1.2
MLF1608-J –55 to +125 –55 to +125 4,000 4
MLF2012-J t=0.85 –55 to +125 –55 to +125 4,000 10
t=1.25 2,000 14
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
Overview of the MLF-J Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series
MLF1005-J Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
1.00±0.05
0.50±0.05 0.50±0.05
0.10min. 0.10min.
Dimensions in mm
0.5
0.5 0.4 0.5
(6/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF1005-J Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " □□□ " of the Part Number contains the internal code.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L Q L, Q measuring conditions
Self-resonant
frequency
(MHz)
DC resistance
(ȍ)
Rated current
(mA) Part No.
(μH) Tolerance min. typ. Frequency
(MHz)
Current
(mA) min. typ. max. typ. max.
0.10 ±5% 10 30 25 1.0 450 880 0.51 0.33 180 MLF1005VR10JT
0.12 ±5% 10 30 25 1.0 400 800 0.59 0.33 180 MLF1005VR12JT
0.15 ±5% 15 30 25 1.0 350 650 0.63 0.39 180 MLF1005VR15JT
0.18 ±5% 15 30 25 1.0 320 600 0.72 0.40 160 MLF1005VR18JT
0.22 ±5% 15 30 25 1.0 290 450 0.79 0.47 160 MLF1005VR22JT
0.27 ±5% 15 30 25 1.0 260 450 0.91 0.65 150 MLF1005VR27JT
0.33 ±5% 15 30 25 1.0 230 380 1.05 0.80 140 MLF1005VR33JT
0.39 ±5% 15 30 25 1.0 210 330 1.35 0.89 130 MLF1005VR39JT
0.47 ±5% 15 30 25 1.0 190 300 1.50 0.95 120 MLF1005VR47JT
0.56 ±5% 15 30 25 1.0 170 250 1.95 1.35 120 MLF1005VR56JT
0.39 ±5% 30 50 10 1.0 210 600 0.41 0.24 50 MLF1005GR39JT
0.47 ±5% 30 50 10 1.0 190 460 0.42 0.25 50 MLF1005GR47JT
0.56 ±5% 30 55 10 1.0 170 450 0.47 0.34 45 MLF1005GR56JT
0.68 ±5% 30 55 10 1.0 150 360 0.55 0.43 45 MLF1005GR68JT
0.82 ±5% 30 55 10 1.0 130 320 0.59 0.43 40 MLF1005GR82JT
1.0 ±5% 30 60 10 1.0 120 290 0.64 0.45 40 MLF1005G1R0JT
1.2 ±5% 30 60 10 1.0 110 230 0.79 0.55 35 MLF1005G1R2JT
1.5 ±5% 30 60 10 1.0 100 200 0.95 0.68 35 MLF1005G1R5JT
1.8 ±5% 30 60 10 1.0 90 180 1.05 0.75 30 MLF1005G1R8JT
2.2 ±5% 30 60 10 1.0 80 150 1.30 0.99 30 MLF1005G2R2JT
Measurement item Product No. Manufacturer
L, Q 4294A+16034G Agilent Technologies
Self-resonant frequency E4991A Agilent Technologies
DC resistance Type-7561 Yokogawa
(7/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF1005-J Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
0.01
10
1
0.1
Frequency(MHz)
Inductance(μH)
G1R8
G1R2
GR82
GR56
GR39
VR47
VR33
VR22
VR15
VR10
1 10 100 1000
0.01
10
1
0.1
Frequency(MHz)
Inductance(μH)
G2R2
G1R5
G1R0
GR68
GR47
VR56
VR39
VR27
VR18
VR12
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(8/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF1005-J Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
70
60
Q
1 10 100 1000
Frequency(MHz)
VR15
G1R2 GR39
VR47
VR10
GR56
GR82 G1R8
VR33
VR22
0
10
20
30
40
50
70
60
Q
1 10 100 1000
Frequency(MHz)
GR47
G1R0
G2R2
G1R5
GR68 VR56
VR27 VR39
VR12
VR18
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(9/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series
MLF1608-J Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
1.60±0.15
0.80±0.15 0.80±0.15
0.30±0.20 0.30±0.20
Dimensions in mm
Dimensions in mm
(10/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF1608-J Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " □□□ " of the Part Number contains the internal code.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L Q L, Q measuring
conditions
Self-resonant
frequency
(MHz)
DC resistance
(ȍ)
Rated current
(mA) Part No.
(μH) Tolerance min. typ. Frequency
(MHz)
Current
(mA) min. typ. max. typ. max.
0.10 ±5% 15 25 25 1.0 450 600 0.35 0.20 200 MLF1608DR10JT
0.12 ±5% 15 25 25 1.0 400 550 0.40 0.20 200 MLF1608DR12JT
0.15 ±5% 15 25 25 1.0 350 500 0.45 0.25 200 MLF1608DR15JT
0.18 ±5% 15 25 25 1.0 320 450 0.50 0.25 150 MLF1608DR18JT
0.22 ±5% 15 25 25 1.0 290 400 0.55 0.30 150 MLF1608DR22JT
0.27 ±5% 15 25 25 1.0 260 350 0.60 0.35 150 MLF1608DR27JT
0.33 ±5% 15 25 25 1.0 230 320 0.75 0.40 100 MLF1608DR33JT
0.39 ±5% 15 25 25 1.0 210 290 0.85 0.45 100 MLF1608DR39JT
0.47 ±5% 15 30 25 1.0 190 260 0.95 0.50 100 MLF1608DR47JT
0.56 ±5% 15 30 25 1.0 170 230 1.05 0.55 100 MLF1608DR56JT
0.68 ±5% 15 30 25 1.0 150 210 1.25 0.65 70 MLF1608DR68JT
0.82 ±5% 15 30 25 1.0 130 190 1.40 0.75 70 MLF1608DR82JT
1.0 ±5% 35 50 10 1.0 120 170 0.50 0.25 50 MLF1608A1R0JT
1.2 ±5% 35 50 10 1.0 110 150 0.65 0.25 50 MLF1608A1R2JT
1.5 ±5% 35 55 10 1.0 100 140 0.70 0.30 50 MLF1608A1R5JT
1.8 ±5% 35 55 10 1.0 90 130 0.85 0.35 50 MLF1608A1R8JT
2.2 ±5% 35 55 10 1.0 80 120 1.00 0.45 30 MLF1608A2R2JT
2.7 ±5% 35 55 10 1.0 70 110 1.15 0.50 30 MLF1608A2R7JT
3.3 ±5% 35 60 10 1.0 65 100 1.30 0.55 30 MLF1608A3R3JT
3.9 ±5% 35 60 10 1.0 60 90 1.45 0.65 30 MLF1608A3R9JT
4.7 ±5% 35 60 10 1.0 55 80 1.60 0.75 30 MLF1608A4R7JT
5.6 ±5% 35 60 40.1 45 70 1.10 0.55 15 MLF1608E5R6JT
6.8 ±5% 35 60 4 0.1 40 60 1.30 0.65 15 MLF1608E6R8JT
8.2 ±5% 35 60 40.1 35 55 1.50 0.80 10 MLF1608E8R2JT
10 ±5% 30 55 2 0.1 30 50 1.70 1.00 10 MLF1608E100JT
12 ±5% 30 55 20.1 25 45 1.80 1.20 10 MLF1608E120JT
Measurement item Product No. Manufacturer
L, Q 4294A+16034G Agilent Technologies
Self-resonant frequency E4991A Agilent Technologies
DC resistance Type-7561 Yokogawa
(11/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF1608-J Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
0.01
100
10
1
0.1
Frequency(MHz)
Inductance(μH)
E100
DR68
DR47
DR33
DR22
DR15
DR10
E6R8 A4R7
A3R3
A2R2
A1R5
A1R0
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(12/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF1608-J Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
60
70
80
Q
1 10 100 1000
Frequency(MHz)
E100
E6R8
A1R0
DR68
DR15
DR10
A3R3
A2R2
A1R5
DR47
DR22
DR33
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(13/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series
MLF2012-J Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
2.00±0.20
T 1.25±0.20
0.50±0.30 0.50±0.30
T
0.85±0.20
1.25±0.20
Dimensions in mm
1.2
0.8 1.0 0.8
(14/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF2012-J Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " □□□ " of the Part Number contains the internal code.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Thickness
T
(mm)
L Q L, Q measuring
conditions
Self-resonant
frequency
(MHz)
DC resistance
(ȍ)
Rated
current
(mA) Part No.
(μH) Tolerance min. typ. Frequency
(MHz)
Current
(mA) min. typ. max. typ. max.
0.85±0.2 0.10 ±5% 20 30 25 1.0 400 500 0.15 0.10 300 MLF2012DR10JT
0.85±0.2 0.12 ±5% 20 30 25 1.0 360 450 0.20 0.12 300 MLF2012DR12JT
0.85±0.2 0.15 ±5% 20 30 25 1.0 320 410 0.20 0.13 300 MLF2012DR15JT
0.85±0.2 0.18 ±5% 20 30 25 1.0 280 370 0.25 0.15 300 MLF2012DR18JT
0.85±0.2 0.22 ±5% 20 30 25 1.0 250 330 0.30 0.16 250 MLF2012DR22JT
0.85±0.2 0.27 ±5% 20 30 25 1.0 220 300 0.35 0.18 250 MLF2012DR27JT
0.85±0.2 0.33 ±5% 20 30 25 1.0 200 270 0.40 0.23 250 MLF2012DR33JT
0.85±0.2 0.39 ±5% 25 35 25 1.0 180 250 0.45 0.25 200 MLF2012DR39JT
1.25±0.2 0.47 ±5% 25 35 25 1.0 160 230 0.50 0.25 200 MLF2012DR47JT
1.25±0.2 0.56 ±5% 25 35 25 1.0 150 210 0.55 0.30 150 MLF2012DR56JT
1.25±0.2 0.68 ±5% 25 35 25 1.0 140 190 0.60 0.35 150 MLF2012DR68JT
1.25±0.2 0.82 ±5% 25 35 25 1.0 130 170 0.65 0.40 150 MLF2012DR82JT
0.85±0.2 1.0 ±5% 45 55 10 1.0 120 160 0.30 0.15 80 MLF2012A1R0JT
0.85±0.2 1.2 ±5% 45 55 10 1.0 110 150 0.35 0.15 80 MLF2012A1R2JT
0.85±0.2 1.5 ±5% 45 60 10 1.0 100 140 0.40 0.18 80 MLF2012A1R5JT
0.85±0.2 1.8 ±5% 45 60 10 1.0 90 130 0.45 0.20 80 MLF2012A1R8JT
0.85±0.2 2.2 ±5% 45 60 10 1.0 80 120 0.50 0.22 50 MLF2012A2R2JT
1.25±0.2 2.7 ±5% 45 70 10 1.0 70 100 0.55 0.25 50 MLF2012A2R7JT
1.25±0.2 3.3 ±5% 45 70 10 1.0 60 90 0.60 0.28 50 MLF2012A3R3JT
1.25±0.2 3.9 ±5% 45 70 10 1.0 55 80 0.65 0.30 30 MLF2012A3R9JT
1.25±0.2 4.7 ±5% 45 70 10 1.0 50 70 0.70 0.35 30 MLF2012A4R7JT
1.25±0.2 5.6 ±5% 50 75 40.1 45 65 0.60 0.30 15 MLF2012E5R6JT
1.25±0.2 6.8 ±5% 50 75 4 0.1 40 60 0.65 0.32 15 MLF2012E6R8JT
1.25±0.2 8.2 ±5% 50 75 40.1 35 55 0.70 0.35 15 MLF2012E8R2JT
1.25±0.2 10 ±5% 50 75 2 0.1 30 50 0.80 0.40 15 MLF2012E100JT
1.25±0.2 12 ±5% 50 75 20.1 25 45 0.90 0.50 15 MLF2012E120JT
Measurement item Product No. Manufacturer
L, Q 4294A+16034G Agilent Technologies
Self-resonant frequency E4991A Agilent Technologies
DC resistance Type-7561 Yokogawa
(15/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF2012-J Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
0.01
100
10
1
0.1
Frequency(MHz)
Inductance(μH)
E100
DR68
DR47
DR33
DR22
DR15
DR10
E6R8 A4R7
A3R3
A2R2
A1R5
A1R0
1 10 100 1000
0.01
100
10
1
0.1
Frequency(MHz)
Inductance(μH)
E120
E8R2
E5R6 A3R9
A2R7
A1R8
DR82
DR56
DR39
DR27
DR18
DR12
A1R2
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(16/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series MLF2012-JType
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
90
70
80
60
Q
110 1000100
Frequency(MHz)
E100
E6R8
A1R0
DR33
DR15
DR10
A3R3
A2R2
A1R5
DR47
DR22
DR68
A4R7
0
10
20
30
40
50
90
80
70
60
Q
110 1000100
Frequency(MHz)
E120
E8R2
E5R6 A3R9
A2R7
A1R8
DR82
DR56
DR39
DR27
DR18
DR12
A1R2
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(17/17)
INDUCTORS
001-01 / 20130929 / inductor_standard_mlf-j_en.fm
• All specifications are subject to change without notice.
MLF-J series
Packaging Style
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
8.0±0.3 3.5±0.05
1.75±0.1
4.0±0.1
1.5 +0.1
–0.0
Sprocket hole Cavity
A
KB
2.0±0.05 2.0±0.05
160min. Taping 200min.
300min.
Drawing direction
Dimensions in mm
Ty p e A B K
MLF1005-J 1.150.1 0.65±0.1 0.8 max.
MLF1608-J 1.90.2 1.1±0.2 1.1 max.
MLF2012-J t=0.85 2.30.2 1.5±0.2 1.1 max.
t=1.25 2.30.2 1.5±0.2 1.5 max.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TDK:
MLF1608A3R3JTD25 MLF2012E8R2JTD25 MLF1608A2R2JTD25 MLF1608DR27JTD25 MLF1608DR47JTD25
MLF1608A3R9JTD25 MLF2012DR39JTD25 MLF2012A1R5JTD25 MLF2012DR12JTD25 MLF1608A2R7JTD25
MLF2012DR22JTD25 MLF1608A4R7JTD25 MLF1608DR82JTD25 MLF2012DR10JTD25 MLF2012DR33JTD25
MLF2012E120JTD25 MLF2012A2R7JTD25 MLF2012E100JTD25 MLF1608A1R0JTD25 MLF1608DR56JTD25
MLF2012E6R8JTD25 MLF2012A4R7JTD25 MLF1608DR15JTD25 MLF1608E100JTD25 MLF1608E120JTD25
MLF1608DR33JTD25 MLF2012DR47JTD25 MLF2012DR27JTD25 MLF1608DR39JTD25 MLF2012A1R8JTD25
MLF1608DR10JTD25 MLF2012A2R2JTD25 MLF1608DR12JTD25 MLF1608DR22JTD25 MLF2012A3R3JTD25
MLF1608A1R5JTD25 MLF1608A1R8JTD25 MLF2012DR15JTD25 MLF2012A1R0JTD25 MLF2012DR56JTD25
MLF1608DR18JTD25 MLF1608E8R2JTD25 MLF2012DR18JTD25 MLF2012DR68JTD25 MLF2012A3R9JTD25
MLF2012E5R6JTD25 MLF2012A1R2JTD25 MLF1608E6R8JTD25 MLF1608A1R2JTD25 MLF1608E5R6JTD25
MLF2012DR82JTD25 MLF1608DR68JTD25