www.fairchildsemi.com ILC5061 Power Supply reset Monitor with 1% Precision Features Description * * * * * * All-CMOS design in SOT-23 or SC70 package 1% precision in Reset Detection Only 1A of Iq 2mA of sink current capability Built-in hysteresis of 5% of detection voltage Voltage options of 2.6, 2.9, 3.1, 4.4, and 4.6V fit most supervisory applications * Open-Drain Reset Output All-CMOS Monitor circuits in either a 3-lead SOT-23 or SC70 package offer the best performance in power consumption and accuracy. Applications Additionally, a built-in hysteresis of 5% of detect voltage simplifies system design. * * * * The ILC5061 comes in a series of 1% accurate trip voltages to fit most microprocessor applications. Even though its output can sink 2mA, the device draws only 1A in normal operation. Microprocessor reset circuits Memory battery back-up circuitry Power-on reset circuits Portable and battery powered electronics Block Diagram Pin Package Configurations VIN Top View VOUT VOUT 1 VOUT SC-70 3 1 SOT-23 VIN 3 VIN VREF VSS 2 VSS 2 VSS Rev. 2.5 1/2/03 ILC5061 PRODUCT SPECIFICATION Absolute Maximum Ratings Parameter Symbol Ratings Units Input Voltages VIN 12 V Output Current IOUT 50 mA Output Voltages VOUT VSS-0.3~+VIN+03 V Pd 150 mW Topr -30~+80 Continuous Total Power Dissipation SOT 23 Operation Ambient temperature Storage Temperature Tstg -40~+125 o C oC Electrical Characteristics TA = 25C Parameter Symbol Conditions Min Type Max Units VDF VDF X 1.01 V VDF X 0.05 VDF X 0.08 V Detect Fail Voltage VDF VDF X 0.99 Hysteresis Range VHYS VDF X 0.02 VIN = 1.5V 0.9 1.0 1.3 1.6 2.0 VIN = 2.0V Supply Current ISS VIN = 3.0V VIN = 4.0V VIN = 5.0V Operating Voltage VIN VDF = 2.1~ 6.0V 1.5 2.6 3.0 3.4 3.8 4.2 A 10.0 V N-ch VDS = 0.5V 2.2 7.7 10.1 11.5 13.0 VIN = 1.0V Output Current IOUT VIN = 2.0V VIN = 3.0V VIN = 4.0V mA VIN = 5.0V Temperature Characteristics Delay Time Release Voltage Output Inversion) DVDF/(DTopr * VDF) -30oC<Topr<80oC -200 +100 +200 Ppm/ oC 0.1 ms TDLY (VDR to VOUT inversion) Note: 1. An additional resistor between the VIN pin and supply voltage may cause deterioration of the characteristics due to increasing VDR. 2 Rev. 2.5 1/2/03 PRODUCT SPECIFICATION ILC5061 Functional Description The following designators 1~6 refer to the timing diagram below. 1. While the input voltage (VIN) is higher than the detect voltage (VDF), the VOUT output pin is at high impedance state. 2. When the input VIN voltage falls lower than VDF, VOUT drops near to ground voltage 3. If the input voltage further decreases below the minimum operating voltage (VMIN), the VOUT output becomes unstable. In this condition, if the VOUT pin is pulled up, VOUT indicates the VIN voltage. 4. During an increase of the input voltage from the VSS voltage, VOUT is not stable in the voltage below the VMIN. Exceeding that level, the output stays at the ground level (VSS) between the minimum operating voltage (VMIN) and the detect release voltage (VDR). 5. If the input voltage increases more than VDR, then the VOUT output pin is at high impedance state. 6. The difference between VDR and VDF is the hysteresis in the system. INPUT VOLTAGE (VIN) DETECT RELEASE VOLTAGE (VDR) 6 DETECT FAIL VOLTAGE (VDF) MINIMUM OPERATING VOLTAGE (VMIN) GROUND VOLTAGE (VSS) OUTPUT VOLTAGE (VOUT) GROUND VOLTAGE (VSS) 1 Rev. 2.5 1/2/03 2 3 4 5 3 ILC5061 PRODUCT SPECIFICATION Typical Performance Characteristics (General conditions for all curves) Output Voltage vs Output Current Output Voltage vs Output Current 80 ILC5061 800 70 60 OUTPUT CURRENT IOUT (A) OUTPUT CURRENT IOUT (mA) VIN = 4.0V 3.5V 50 3.0V 40 2.5V 30 2.0V 20 10 ILC5061 VIN = 0.8V 600 400 VIN = 0.7V 200 1.5V 0 0 0 1 3 2 4 0 0.6 0.8 OUTPUT VOLTAGE VOUT (V) Ordering Information ISS vs Input Voltage* 4.0 0.4 0.2 OUTPUT VOLTAGE VOUT (V) Output Current vs Input Voltage ILC5061 20 ILC5061 Topr = -30C Topr = 80C 3.0 ISS (A) OUTPUT CURRENT IOUT (mA) VDS = 0.5V 2.0 25C -30C 1.0 0 25C 15 80C 10 5 0 0 1 2 3 4 5 6 7 8 9 10 INPUT VOLTAGE VIN (V) 0 1 2 3 4 5 INPUT VOLTAGE VIN (V) * A spike of 1/2 to 1A may appear as VIN crosses VDR or VDF 4 Rev. 2.5 1/2/03 PRODUCT SPECIFICATION ILC5061 SOT-23 Package 0.021 0.015 0.055 0.047 0.098 0.083 0.120 0.105 0.0059 0.0035 0.040 0.031 0.079 0.071 0-8 0.010 0.005 0.004 0.001 0.76 2.29 PKG CL 0.76 0.95 LAND PATTERN RECOMMENDATION Rev. 2.5 1/2/03 5 ILC5061 PRODUCT SPECIFICATION SC70 Package .087 (2.2) .071 (1.8) .053 (1.35) .045 (1.15) .087 (2.2) .079 (2.0) .009 (.23) .005 (.13) .043 (1.1) .032 (.80) .004 (.10) .010 (.25) .004 (.10) .016 (.40) .012 (.30) .026 (.65) .018 (.45) .006 (.15) .052 (1.3) 0.65 0.5 0.6 1.80 0.65 Land Pattern Recommendation 6 Rev. 2.5 1/2/03 PRODUCT SPECIFICATION ILC5061 Ordering Information PART NUMBER TOP MARKING RESET THRESHOLD (V) OUTPUT TYPE PACKAGE PACKING METHOD ILC5061AM23X M3AY 2.3 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM25X M5AY 2.5 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM26X M6AY 2.6 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM27X M7AY 2.7 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM28X M8AY 2.8 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM29X M9AY 2.9 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM31X N1AY 3.1 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM32X N2AY 3.2 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM34X N4AY 3.4 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM37X N7AY 3.7 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM44X P4AY 4.4 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061AM46X P6AY 4.6 1 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M23X M3Y 2.3 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M25X M5Y 2.5 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M26X M6Y 2.6 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M27X M7Y 2.7 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M28X M8Y 2.8 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M29X M9Y 2.9 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M31X N1Y 3.1 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M32X N2Y 3.2 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M34X N4Y 3.4 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M37X N7Y 3.7 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M44X P4Y 4.4 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R ILC5061M46X P6Y 4.6 2 % Open-Drain, active low 3-Pin, SOT23 3K units in T&R Note 1:Last digit in the "Top Marking" information (represented by "Y" in the above table) represents internal assembly lot number Note 2:Orientation of Tape & Reeled devices is Right. Rev. 2.5 1/2/03 7 ILC5061 PRODUCT SPECIFICATION Ordering Information PART NUMBER TOP MARKING RESET THRESHOLD (V) OUTPUT TYPE PACKAGE PACKING METHOD ILC5061AIC23X M3AY 2.3 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC25X M5AY 2.5 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC26X M6AY 2.6 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC27X M7AY 2.7 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC28X M8AY 2.8 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC29X M9AY 2.9 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC31X N1AY 3.1 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC32X N2AY 3.2 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC34X N4AY 3.4 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC37X N7AY 3.7 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC44X P4AY 4.4 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061AIC46X P6AY 4.6 1 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC23X M3Y 2.3 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC25X M5Y 2.5 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC26X M6Y 2.6 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC27X M7Y 2.7 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC28X M8Y 2.8 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC29X M9Y 2.9 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC31X N1Y 3.1 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC32X N2Y 3.2 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC34X N4Y 3.4 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC37X N7Y 3.7 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC44X P4Y 4.4 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R ILC5061IC46X P6Y 4.6 2 % Open-Drain, active low 3-Pin, SC70 3K units in T&R Note 1: Last digit in the "Top Marking" information (represented by "Y" in the above table) represents internal assembly lot number Note 2: Orientation of Tape & Reeled devices is Right. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 1/2/03 0.0m 001