NCP1082 Integrated PoE-PD & DC-DC Converter Controller with 9V Auxiliary Supply Support Introduction The NCP1082 is a member of ON Semiconductor's Power over Ethernet Powered Device (PoE-PD) product family and represents a robust, flexible and highly integrated solution targeting demanding Ethernet applications. It combines in a single unit an enhanced PoE-PD interface fully supporting the IEEE 802.3af specification and a flexible and configurable DC-DC converter controller. The NCP1082's exceptional capabilities enable applications to smoothly transition from non-PoE to PoE enabled networks by also supporting power from auxiliary sources such as AC power adapters and battery supplies, eliminating the need for a second switching power supply. ON Semiconductor's unique manufacturing process and design enhancements allow the NCP1082 to deliver up to 13 W of regulated power to support PoE applications according to the IEEE 802.3af standard. This device leverages the significant cost advantages of PoE-enabled systems to a broad spectrum of products in markets such as VoIP phones, wireless LAN access points, security cameras, point of sales terminals, RFID readers, industrial ethernet devices, etc. The integrated current mode DC-DC controller facilitates isolated and non-isolated fly-back, forward and buck converter topologies. It has all the features necessary for a flexible, robust and highly efficient design including programmable switching frequency, duty cycle up to 80 percent, slope compensation, and soft start-up. The NCP1082 is fabricated in a robust high voltage process and integrates a rugged vertical N-channel DMOS with a low loss current sense technique suitable for the most demanding environments and capable of withstanding harsh environments such as hot swap and cable ESD events. The NCP1082 complements ON Semiconductor's ASSP portfolio in communications and industrial devices and can be combined with other high-voltage interfacing devices to offer complete solutions to the communication, industrial and security markets. Features Powered Device Interface Connections Fully Supports IEEE 802.3af Standard Regulated Power Output up to 13 W Programmable Classification Current Adjustable Under Voltage Lock Out Programmable Inrush Current Limit (c) Semiconductor Components Industries, LLC, 2008 November, 2008 - Rev. 0 1 TSSOP-20 EP DE SUFFIX CASE 948AB NCP1082 = Specific Device Code XXXX = Date Code Y = Assembly Location ZZ = Traceability Code ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. * Programmable Operational Current Limit up to 500 mA * Over-temperature Protection * Industrial Temperature Range -40C to 85C with Full * Flexible Auxiliary Power Supply Support * 9 V Front, Rear and Direct Auxiliary Supply * * * * * http://onsemi.com Operation up to 150C Junction Temperature * 0.6 Ohm Hot-swap Pass-switch with Low Loss * 1 Current Sense Technique Vertical N-channel DMOS Pass-switch Offers the Robustness of Discrete MOSFETs with Integrated Temperature Control Publication Order Number: NCP1082/D NCP1082 DC-DC Converter Controller PIN DIAGRAM * Current Mode Control * Supports Isolated and Non-isolated DC-DC Converter VPORTP CLASS UVLO INRUSH ILIM1 VPORTN1 RTN VPORTN2 AUX TEST Applications * Internal Voltage Regulators * Wide Duty Cycle Range with Internal Slope Compensation Circuitry * Programmable Oscillator Frequency * Programmable Soft-start Time SS FB COMP VDDL VDDH GATE ARTN NC CS OSC 1 Exposed Pad (Top View) Ordering Information Package Shipping Configuration Temperature Range NCP1082DEG TSSOP-20 EP (Pb-Free) 74 units / Tube -40C to 85C NCP1082DER2G TSSOP-20 EP (Pb-Free) 2500 / Tape & Reel -40C to 85C Part Number For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. VPORTP DETECTION AUX INTERNAL SUPPLY & BANDGAP THERMAL SHUT DOWN AUXILIARY SUPPLY DETECTION VDDH VDDH VDDL VDDL VDDL CLASS VDDL CLASSIFICATION 5 mA SS VDDL UVLO UVLO 5K VPORT MONITOR DC-DC CONVERTER CONTROL 1.2 V FB COMP CS OSC OSC VDDH INRUSH ILIM1 HOT SWAP SWITCH INRUSH ILIM1 GATE CONTROL & CURRENT LIMIT BLOCKS NC ARTN RTN VPORTN1,2 Figure 1. NCP1082 Block Diagram http://onsemi.com 2 NCP1082 Simplified Application Diagrams VAUX(+) D4 RJ-45 Rclass Cline DB1 R1 Data Pairs Rinrush Rilim1 Raux1 VPORTP CLASS Cpd VDDH VDDL ILIM1 UVLO Raux3 R2 Spare Pairs GATE CS FB ARTN RTN AUX TEST VPORTN1 VPORTN2 SS OSC COMP DB2 Z_line LD1 Rd1 Cvddl NCP1082 D3 Voutput Cload INRUSH Raux2 D1 T1 Cvddh M1 Rslope Rcs Optocoupler R5 OC1 C2 R3 C1 Rosc Z1 Css R4 VAUX(-) Figure 2. Isolated Fly-back Converter with Rear Auxiliary Support Figure 2 shows the integrated PoE-PD switch and DC-DC controller configured to work in a fully isolated application. The output voltage regulation is accomplished with an external opto-coupler and a shunt regulator (Z1). VAUX(+) D3 RJ-45 Rclass Cline DB1 R1 Data Pairs Rinrush Rilim1 Raux1 VPORTP CLASS INRUSH UVLO Raux3 R2 Spare Pairs VDDL Z_line GATE CS AUX TEST FB VPORTN1 ARTN VPORTN2 RTN SS OSC COMP Rosc Css VAUX(-) LD1 Cvddl NCP1082 D2 T1 Cvddh ILIM1 Raux2 DB2 Cpd VDDH D1 R3 Voutput Cload Rd1 M1 Rslope R4 Rcs Rcomp C1comp C2comp Figure 3. Non-Isolated Fly-back Converter with Rear Auxiliary Support Figure 3 shows the integrated PoE-PD and DC-DC controller configured in a non-isolated fly-back configuration. A compensation network is inserted between the FB and the COMP pin for overall stability of the feedback loop. http://onsemi.com 3 NCP1082 Simplified Application Diagrams VAUX(+) D2 D4 RJ-45 Rclass Cline DB1 R1 Data Pairs Rinrush Rilim1 Raux1 VPORTP CLASS INRUSH UVLO Cvddl AUX TEST VPORTN1 VPORTN2 Raux3 R2 Spare Pairs GATE CS FB ARTN RTN OSC COMP SS Z_line D1 LD1 ILIM1 NCP1082 D3 R5 Cvddh Cpd VDDL Raux2 DB2 VDDH T1 Voutput R3 Cload Rd1 M1 Rslope R4 Rcs Rcomp Rosc Css C1comp VAUX(-) C2comp Figure 4. Non-Isolated Fly-back with Extra Winding and Rear Auxiliary Support Figure 4 shows the same non-isolated fly-back configuration as Figure 3, but adds a 12 V auxiliary bias winding on the transformer to provide power to the NCP1082 DC-DC controller via its VDDH pin. This topology shuts off the current flowing from VPORTP to VDDH and therefore reduces the internal power dissipation of the PD, resulting in higher overall power efficiency. VAUX(+) D5 RJ-45 Rclass Cline DB1 Rinrush R1 Data Pairs Raux1 Rilim1 VPORTP CLASS UVLO Raux3 R2 Spare Pairs Z_line D1 AUX TEST FB VPORTN1 ARTN VPORTN2 RTN SS OSC COMP Rosc Css VAUX(-) Rd1 M1 Rslope Rcomp C1comp Figure 5. Non-Isolated Forward Converter with Rear Auxiliary Support http://onsemi.com 4 R3 R4 Rcs C2comp Figure 5 shows the NCP1082 used in a non-isolated forward topology. D2 LD1 Cvddl GATE CS L1 Voutput Cvddh VDDL ILIM1 NCP1082 D4 DB2 VDDH INRUSH Raux2 D3 T1 Cpd Cload NCP1082 Table 1. Pin Descriptions Name Pin No. Type 1 Supply Positive input power. Voltage with respect to VPORTN1,2 6,8 Ground Negative input power. Connected to the source of the internal pass-switch. RTN 7 Ground DC-DC controller power return. Connected to the drain of the internal pass-switch. It must be connected to ARTN. This pin is also the drain of the internal pass-switch. ARTN 14 Ground DC-DC controller ground pin. Must be connected to RTN as a single point ground connection for improved noise immunity. VDDH 16 Supply Output of the 9 V LDO internal regulator. Voltage with respect to ARTN. Supplies the internal gate driver. VDDH must be bypassed to ARTN with a 1 mF or 2.2 mF ceramic capacitor with low ESR. VDDL 17 Supply Output of the 3.3 V LDO internal regulator. Voltage with respect to ARTN. This pin can be used to bias an external low-power LED (1 mA max.) connected to ARTN, and can also be used to add extra biasing current in the external opto-coupler. VDDL must be bypassed to ARTN with a 330 nF or 470 nF ceramic capacitor with low ESR. CLASS 2 Input Classification current programming pin. Connect a resistor between CLASS and VPORTN1,2. INRUSH 4 Input Inrush current limit programming pin. Connect a resistor between INRUSH and VPORTN1,2. ILIM1 5 Input Operational current limit programming pin. Connect a resistor between ILIM1 and VPORTN1,2. UVLO 3 Input DC-DC controller under-voltage lockout input. Voltage with respect to VPORTN1,2. Connect a resistor-divider from VPORTP to UVLO to VPORTN1,2 to set an external UVLO threshold. GATE 15 Output OSC 11 Input NC 13 COMP 18 I/O Output of the internal error amplifier of the DC-DC controller. COMP is pulled-up internally to VDDL with a 5 kW resistor. In isolated applications, COMP is connected to the collector of the opto-coupler. Voltage with respect to ARTN. FB 19 Input DC-DC controller inverting input of the internal error amplifier. In isolated applications, the pin should be strapped to ARTN to disable the internal error amplifier. CS 12 Input Current-sense input for the DC-DC controller. Voltage with respect to ARTN. SS 20 Input Soft-start input for the DC-DC controller. A capacitor between SS and ARTN determines the soft-start timing. AUX 9 Input When the pin is pulled up, the IEEE detection mode is disabled and the device can be supplied by an auxiliary supply. Voltage with respect to VPORTN1,2. Connect the pin to the auxiliary supply through a resistor divider. TEST 10 Input Digital test pin must always be connected to VPORTN1,2. VPORTP VPORTN1 VPORTN2 EP Description DC-DC controller gate driver output pin. Internal oscillator frequency programming pin. Connect a resistor between OSC and ARTN. No connect pin, must not be connected. Exposed pad. Connected to VPORTN1,2 ground. http://onsemi.com 5 NCP1082 Table 2. Absolute Maximum Ratings Symbol Min. Max. Units Input power supply -0.3 72 V Voltage with respect to VPORTN1,2 RTN ARTN Analog ground supply 2 -0.3 72 V Pass-switch in off-state (Voltage with respect to VPORTN1,2) VDDH Internal regulator output -0.3 17 V Voltage with respect to ARTN VDDL Internal regulator output -0.3 3.6 V Voltage with respect to ARTN CLASS Analog output -0.3 3.6 V Voltage with respect to VPORTN1,2 INRUSH Analog output -0.3 3.6 V Voltage with respect to VPORTN1,2 ILIM1 Analog output -0.3 3.6 V Voltage with respect to VPORTN1,2 UVLO Analog input -0.3 3.6 V Voltage with respect to VPORTN1,2 OSC Analog output -0.3 3.6 V Voltage with respect to ARTN Analog input / output -0.3 3.6 V Voltage with respect to ARTN FB Analog input -0.3 3.6 V Voltage with respect to ARTN CS Analog input -0.3 3.6 V Voltage with respect to ARTN SS Analog input -0.3 3.6 V Voltage with respect to ARTN NC Open pin VPORTP COMP Parameter Conditions AUX Analog input -0.3 3.6 V Voltage with respect to VPORTN1,2 TEST Digital input -0.3 3.6 V Voltage with respect to VPORTN1,2 Ta Ambient temperature -40 85 C Tj Junction temperature - 150 C Junction temperature (Note 1) - 175 C -55 150 C 37.6 C/W Tj-TSD Tstg Storage Temperature TJA Thermal Resistance, Junction to Air (Note 2) ESD-HBM Human Body Model 3.5 - kV ESD-CDM Charged Device Model 750 - V Machine Model 300 - V Latch-up 200 - mA System ESD (contact/air) (Note 3) 8/15 - kV ESD-MM LU ESD-SYS Thermal shutdown condition Exposed pad connected to VPORTN1,2 ground per MIL-STD-883, Method 3015 per JEDEC Standard JESD78 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Tj-TSD allowed during error conditions only. It is assumed that this maximum temperature condition does not occur more than 1 hour cumulative during the useful life for reliability reasons. 2. Mounted on a 1S2P (3 layer) test board with copper coverage of 25 percent for the signal layers and 90 percent copper coverage for the inner planes at an ambient temperature of 85C in still air. Refer to JEDEC JESD51-7 for details. 3. Surges per EN61000-4-2, 1999 applied between RJ-45 and output ground and between adapter input and output ground of the demo board. The specified values are the test levels and not the failure levels. http://onsemi.com 6 NCP1082 Recommended Operating Conditions Operating conditions define the limits for functional operation and parametric characteristics of the device. Note that the functionality of the device outside the operating conditions described in this section is not warranted. Operating outside the recommended operating conditions for extended periods of time may affect device reliability. All values concerning the DC-DC controller, VDDH and VDDL blocks are with respect to ARTN. All others are with respect to VPORTN1,2 (unless otherwise noted). Table 3. Operating Conditions Symbol Parameter Min. Typ. Max. Units 0 57 V 1.4 9.5 V 23.75 26.25 kW Conditions INPUT SUPPLY VPORT Input supply voltage VPORT = VPORTP - VPORTN1,2 SIGNATURE DETECTION Vsignature Input supply voltage signature detection range Rsignature Signature resistance (Note 4) Offset_current I_VportP + I_Rtn - 1.8 5 mA VPORTP = RTN = 1.4 V Sleep_current I_VportP + I_Rtn - 15 25 mA VPORTP = RTN = 9.5 V 20.5 V CLASSIFICATION Vcl Input supply voltage classification range 13 Iclass0 Class 0: Rclass 10 kW (Note 5) 0 - 4 mA Iclass0 = I_VportP + I_Rdet Iclass1 Class 1: Rclass 130 W (Note 5) 9 - 12 mA Iclass1 = I_VportP + I_Rdet Iclass2 Class 2: Rclass 69.8 W (Note 5) 17 - 20 mA Iclass2 = I_VportP + I_Rdet Iclass3 Class 3: Rclass 44.2 W (Note 5) 26 - 30 mA Iclass3 = I_VportP + I_Rdet Iclass4 Class 4: Rclass 30.9 W (Note 5) 36 - 44 mA Iclass4 = I_VportP + I_Rdet IDCclass Internal current consumption during classification (Note 6) - 600 - mA For information only 38 40 V UVLO pin tied to VPORTN1,2 29.5 32 - V UVLO pin tied to VPORTN1,2 UVLO Vuvlo_on Default turn on voltage (VportP rising) Vuvlo_off Default turn off voltage (VportP falling) Vhyst_int UVLO internal hysteresis - 6 - V UVLO pin tied to VPORTN1,2 Vuvlo_pr UVLO external programming range 13 - 50 V UVLO pin connected to the resistor divider (R1 & R2) AUX pin tied to VPORTN1,2 For information only 8.5 - 18 V UVLO & AUX pins configured for auxiliary supply support Vuvlo_pr_aux UVLO external programming VPORT range with low auxiliary supply support Vhyst_ext UVLO external hysteresis - 15 - % UVLO pin connected to the resistor divider (R1 & R2) Uvlo_Filter UVLO on/off filter time - 90 - mS For information only AUXILIARY SUPPLY OPERATION - INPUT SUPPLY Vaux_min1 VPORTP-ARTN voltage at startup (required for VDDH > VDDH_Por_R) 8.7 - - V VAUX rising - No external load on VDDL & VDDH Vaux_min2 VPORTP-ARTN voltage during PWM operation (required for VDDH > VDDH_Por_F) 8.5 - - V Voltage with respect to Ivddl_load1 & Ivddh_load1 for the load current conditions 4. Test done according to the IEEE 802.3af 2 Point Measurement. The minimum probe voltages measured at the PoE-PD are 1.4 V and 2.4 V, and the maximum probe voltages are 8.5 V and 9.5 V. 5. Measured with an external Rdet of 25.5 kW between VPORTP and VPORTN1,2, and for 13 V < VPORT < 20.5 V (with VPORT = VPORTP - VPORTN1,2). 6. This typical current excludes the current in the Rclass and Rdet external resistors. http://onsemi.com 7 NCP1082 Table 3. Operating Conditions Symbol Parameter Min. Typ. Max. Units Conditions AUXILIARY SUPPLY OPERATION - AUX PIN AUX_threshold AUX pin internal threshold 0.2 - 1.5 V Voltage with respect to VPORTN1,2. AUX_bias_min Minimum Voltage required on the AUX pin for low auxiliary supply operation 1.5 - - V Defined at VPORT = 8.5 V, Voltage with respect to VPORTN1,2 AUX_bias_max Maximum Voltage allowed on the AUX pin - - 3.3 V Voltage with respect to VPORTN1,2 AUX_res_ladder Resistor ladder value on AUX pin - - 25 kW Between VAUX supply & VPORTN1,2 AUXILIARY SUPPLY OPERATION - VDDL REGULATOR Ivddl_load1 Current load on the VDDL pin with VPORTP - ARTN = 8.5 V (Notes 7 and 8) - - 1 mA Ivddh_load + Ivddl_load < 4.5 mA Ivddl_load2 Current load on the VDDL pin with VPORTP - ARTN > 12.5 V (Notes 7 and 8) - - 2.25 mA Ivddh_load + Ivddl_load < 10 mA AUXILIARY SUPPLY OPERATION - VDDH REGULATOR Ivddh_load1 Current load on the VDDH regulator with VPORTP - ARTN = 8.5 V (Notes 7 and 8) - - 4.5 mA Ivddh_load + Ivddl_load < 4.5 mA Ivddh_load2 Current load on the VDDH regulator with VPORTP - ARTN > 12.5 V (Notes 7 and 8) - - 10 mA Ivddh_load + Ivddl_load < 10 mA PASS-SWITCH AND CURRENT LIMITS Ron Pass-switch Rds-on - 0.6 1.2 W Max Ron specified at Tj = 130C I_Rinrush1 Rinrush = 150 kW (Note 9) 95 125 155 mA Measured at RTN- VPORTN1,2 = 3 V I_Rinrush2 Rinrush = 57.6 kW (Note 9) 260 310 360 mA Measured at RTN- VPORTN1,2 = 3 V I_Rilim1 Rilim1 = 84.5 kW (Note 9) 450 510 570 mA Current limit threshold 0.8 1 1.2 V RTN-VPORTNx falling; voltage with respect to VPORTN1,2 - 8.2 - V Voltage with respect to VPORTN1,2 INRUSH AND ILIM1 CURRENT LIMIT TRANSITION Vds_pgood VDS required for power good status Vds_pgood_hyst VDS hysteresis required for power good status 7. Ivddl_load = current flowing out of the VDDL pin. Ivddh_load = current flowing out of the VDDH pin + current delivered to the Gate Driver (function of the frequency, VDDH voltage & MOSFET gate capacitance). 8. See Figures 6 and 7 for specifications on the load current at lower or higher VPORTP-ARTN voltages. In case the application requires more current capability on VDDL and VDDH, it is recommended to externally supply the VDDH pin with a bias winding from the transformer or to add a diode between VAUX(+) and VDDH pin (verify the VAUX voltage does not exceed the VDDH voltage range). 9. The current value corresponds to the PoE-PD input current (the current flowing in the external Rdet and the quiescent current of the device are included). http://onsemi.com 8 NCP1082 Table 3. Operating Conditions Symbol Parameter Min. Typ. Max. Units Conditions VDDH REGULATOR VDDH_reg Regulator output voltage (Notes 10 and 11) 8.4 9 9.6 V Ivddh_load + Ivddl_load < 10 mA with Ivddl_load < 2.25 mA and 12.5 V < VPORTP - ARTN < 57 V VDDH_Off Regulator turn-off voltage - VDDH_reg + 0.5 V - V For information only VDDH_lim VDDH regulator current limit (Notes 10 and 11) 13 - 26 mA VDDH_Por_R VDDH POR level (rising) 7.3 - 8.3 V VDDH_Por_F VDDH POR level (falling) 6 - 7 V VDDH_ovlo VDDH over-voltage level (rising) 16 - 18.5 V VDDL REGULATOR VDDL_reg Regulator output voltage (Notes 10 and 11) 3.05 3.3 3.55 V Ivddl_load < 2.25 mA with Ivddh_load + Ivddl_load < 10 mA and 12.5 V < VPORTP - ARTN < 57 V VDDL_Por_R VDDL POR level (rising) VDDL - 0.2 - VDDL - 0.02 V VDDL_Por_F VDDL POR level (falling) 2.5 - 2.9 V Gate_Tr GATE rise time (10-90%) - - 50 ns Cload = 2 nF, VDDHreg = 9 V Gate_Tf GATE fall time (90-10%) - - 50 ns Cload = 2 nF, VDDHreg = 9 V 1.3 - 3 V For information only V Voltage with respect to ARTN GATE DRIVER PWM COMPARATOR VCOMP COMP control voltage range ERROR AMPLIFIER Vbg_fb Reference voltage 1.15 1.2 1.25 Av_ol DC open loop gain - 80 - dB For information only GBW Error amplifier GBW 1 - - MHz For information only Vss Soft-start voltage range - 1.15 - V Vss_r Soft-start low threshold (rising edge) 0.35 0.45 0.55 V Iss Soft-start source current 3 5 7 mA 324 360 396 mV - 100 - nS SOFT-START CURRENT LIMIT COMPARATOR CSth CS threshold voltage Tblank Blanking time For information only 10. Power dissipation must be considered. Load on VDDH and VDDL must be limited especially if VDDH is not powered by an auxiliary winding. 11. Ivddl_load = current flowing out of the VDDL pin. Ivddh_load = current flowing out of the VDDH pin + current delivered to the Gate Driver (function of the frequency, VDDH voltage & MOSFET gate capacitance). http://onsemi.com 9 NCP1082 Table 3. Operating Conditions Symbol Parameter Min. Typ. Max. - 80% - 100 - 500 Units Conditions OSCILLATOR DutyC Maximum duty cycle Frange Oscillator frequency range F_acc Oscillator frequency accuracy Fixed internally kHz % 25 CURRENT CONSUMPTION IvportP1 VPORTP internal current consumption (Note 12) - 2.5 3.5 mA DC-DC controller off IvportP2 VPORTP internal current consumption (Note 13) - 4.7 6.5 mA DC-DC controller on 150 - - C Tj Tj = junction temperature - 15 - C Tj Tj = junction temperature THERMAL SHUTDOWN TSD Thermal shutdown threshold Thyst Thermal hysteresis THERMAL RATINGS Ta Ambient temperature -40 - 85 C Tj Junction temperature - - 125 150 C C Parametric values guaranteed Max 1000 hours 10.5 10.0 9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 2.50 2.25 LOAD CURRENT (mA) LOAD CURRENT (mA) 12. Conditions a. No current through the pass-switch b. DC-DC controller inactive (SS shorted to RTN) c. No external load on VDDH and VDDL d. VPORTP = 57 V 13. Conditions a. No current through the pass-switch b. Oscillator frequency = 100 kHz c. No external load on VDDH and VDDL d. Aux winding not used e. 2 nF on GATE, DC-DC controller enabled f. VPORTP = 57 V 2.00 1.75 1.50 1.25 1.00 0.75 8.5 9.0 9.5 10 10.5 11 11.5 12 12.5 13 13.5 0.50 8.5 9.0 9.5 10 10.5 11 11.5 12 12.5 13 13.5 VPORTP-ARTN VOLTAGE DURING PWM OPERATION (V) VPORTP-ARTN VOLTAGE DURING PWM OPERATION (V) Figure 6. (Ivddl_load)max with Auxiliary Supply Operation Figure 7. (Ivddh_load+Ivddl_load)max with Auxiliary Supply Operation http://onsemi.com 10 NCP1082 Description of Operation Powered Device Interface Power Mode The PD interface portion of the NCP1082 supports the IEEE 802.3af defined operating modes: detection signature, current source classification, inrush and operating current limits. In order to give more flexibility to the user and also to keep control of the power dissipation in the NCP1082, both current limits are configurable. The device enters operation once its programmable Vuvlo_on threshold is reached, and operation ceases when the supplied voltage falls below the Vuvlo_off threshold. Sufficient hysteresis and Uvlo filter time are provided to avoid false power on/off cycles due to transient voltage drops on the cable. When the classification hand-shake is completed, the PSE and PD devices move into the operating mode. Under Voltage Lock Out (UVLO) The NCP1082 incorporates an under voltage lock out (UVLO) circuit which monitors the input voltage and determines when to apply power to the DC-DC controller. To use the default settings for UVLO (see Table 3), the pin UVLO must be connected to VPORTN1,2. In this case the signature resistor has to be placed directly between VPORTP and VPORTN1,2, as shown in Figure 9. Detection VPORTP During the detection phase, the incremental equivalent resistance seen by the PSE through the cable must be in the IEEE 802.3af standard specification range (23.75 kW to 26.25 kW) for a PSE voltage from 2.7 V to 10.1 V. In order to compensate for the non-linear effect of the diode bridge and satisfy the specification at low PSE voltage, the NCP1082 presents a suitable impedance in parallel with the 25.5 kW Rdet external resistor. For some types of diodes (especially Schottky diodes), it may be necessary to adjust this external resistor. When the Detection_Off level is detected (typically 11.5 V) on VPORTP, the NCP1082 turns on its internal 3.3 V regulator and biasing circuitry in anticipation of the classification phase as the next step. VPORT VPORTN1,2 NCP1082 Figure 9. Default UVLO Settings To define the UVLO threshold externally, the UVLO pin must be connected to the center of an external resistor divider between VPORTP and VPORTN1,2 as shown in Figure 10. The series resistance value of the external resistors must add to 25.5 kW and replaces the internal signature resistor. Classification Once the PSE device has detected the PD device, the classification process begins. In classification, the PD regulates a constant current source that is set by the external resistor RCLASS value on the CLASS pin. Figure 8 shows the schematic overview of the classification block. The current source is defined as: I class + VPORTP V bg R class UVLO Rdet VPORTP R1 VPORT UVLO , (where V bg is 1.2 V) R2 VDDA1 1.2 V VPORTN1,2 NCP1082 CLASS Figure 10. External UVLO Configuration For a Vuvlo_on desired turn-on voltage threshold, R1 and R2 can be calculated using the following equations: Rclass R1 ) R2 + R det VPORTN1,2 R2 + NCP1082 1.2 V ulvo_on R det When using the external resistor divider, the NCP1082 has an external reference voltage hysteresis of 15 percent typical. Figure 8. Classification Block Diagram http://onsemi.com 11 NCP1082 Auxiliary Supply Support To support applications connected to non PoE enabled networks and minimize the bill of materials, the NCP1082 supports drawing power from an external supply. The NCP1082 supports the IEEE 802.3af standard when the PoE capability is available and acts as a regular DC-DC converter when there is no power source on the Ethernet cable as shown in Figure 11. Auxiliary supply support can be implemented in three ways depending on where the auxiliary supply is injected. The front, rear and direct auxiliary supply configurations are explained in more detail in the application note "NCP1082-3 PoE Auxiliary Supply Applications". D1 VAUX(+) POE(+) VPORTP Raux2 Rdet1 NCP1082 Cpd D2 VPORT Optional - for very low VAUX only Raux1 UVLO Rdet2 AUX Raux3 POE(-) Pass Switch VPORTN1,2 VAUX(-) Or RTN DC-DC Stage to VPORTN1,2 (Front AUX Configuration) to RTN (Rear AUX Configuration) Figure 11. Front and Rear Auxiliary Supply Input with Support for Very Low Input Voltages Vdp = 0.5 V the forward voltage drop of the NCP1082 internal diode, and Vt is the desired voltage at the AUX pin. Note that as soon the auxiliary supply is connected the PoE interface (detection and classification) is disabled and does not allow the PD device to be powered from the Ethernet until the auxiliary supply is removed. If the PoE PD device was drawing the current from the Ethernet cable before the auxiliary supply is connected, the power will continue to be supplied from the Ethernet cable unless the voltage of the auxiliary supply is higher than the Ethernet supply voltage. When the auxiliary input supply is above 13.5 V, connect the AUX pin to VPORTN1,2.. When the auxiliary supply is below 13.5 V (but above 9 V), calculate the voltage dividers Raux1, Raux3 and Raux2, Rdet1, Rdet2 to divide the input voltage to at least 2 V at the UVLO pin and 2 V at the AUX pin using the following formulas. Note the maximum voltage is 3.3 V. R aux3 + R aux2 + R aux1 V t V aux * V dp * V t V aux * V dp * V d * V t V aux*V dp*Vd*Vt Vt * 845 24 K Inrush and Operational Current Limitations R aux1 + 20 KW The inrush current limit and the operational current limit are programmed individually by an external Rinrush and Rilim1 resistors respectively connected between INRUSH and VPORTN1,2, and between ILIM1 and VPORTN1,2 as shown in Figure 12. With Vd is the voltage drop over the rectifiers and masking diodes (typical 0.6 V), and VDDA1 VDDA1 ILIM1 / INRUSH Vbg1 Ilim_ref NCP1082 VPORTNx Figure 12. Current Limitation Configuration (Inrush & Ilim1 Pins) http://onsemi.com 12 NCP1082 Inrush 0 Ilim1 1 I_pass_switch & VDS_PGOOD Vds_pgood threshold Current_limit_ON detector VDDA1 VDDA1 VDDA1 2V 1 V / 9.2 V VPORTNx RTN Pass Switch NCP1082 Figure 13. Inrush and Ilim1 Selection Mechanism Thermal Shutdown When VPORT reaches the UVLO_on level, the Cpd capacitor is charged with the INRUSH current (in order to limit the internal power dissipation of the pass-switch). Once the Cpd capacitor is fully charged, the current limit switches from the inrush current to the operational current level (ilim1) as shown in Figure 13. This transition occurs when both following conditions are satisfied: 1. The VDS of the pass-switch is below the Vds_pgood low level (1 V typical). 2. The pass-switch is no longer in current limit mode, meaning the gate of the pass-switch is "high" (above 2 V typical). The operational current limit will stay selected as long as Vds_pgood is true (meaning that RTN-VPORTN1,2 is below the high level of Vds_pgood). This mechanism allows a current level transition without any current spike in the pass-switch because the operational current limit (ilim1) is enabled once the pass-switch is not limiting the current anymore, meaning that the Cpd capacitor is fully charged. The NCP1082 includes thermal protection which shuts down the device in case of high power dissipation. Once the thermal shutdown (TSD) threshold is exceeded, following blocks are turned off: * DC-DC controller * Pass-switch * VDDH and VDDL regulators * CLASS regulator When the TSD error disappears and if the input line voltage is still above the UVLO level, the NCP1082 automatically restarts with the current limit set in the inrush state, the DC-DC controller is disabled and the Css (soft-start capacitor) discharged. The DC-DC controller becomes operational as soon as RTN-VPORTN1,2 is below the Vds_pgood threshold. http://onsemi.com 13 NCP1082 DC-DC Converter Controller The NCP1082 implements a current mode DC-DC converter controller which is illustrated in Figure 14. VPORTP OSC VDDL 5 kW 1.2 V Oscillator & Sawtooth Generator FB Reset CLK VDDL Set CLK 3.3 V LDO COMP 9 V LDO Current Slope Compensation 10 mA 0 VDDH PWM comp CS Blanking time S Q 1.45 V 11 kW Gate Driver GATE R 2 ARTN Current limit comp VDDL 360 mV 5 mA SS Soft-start Figure 14. DC-DC Controller Block Diagram Internal VDDH and VDDL Regulators and Gate Driver In isolated topologies the error amplifier is not used because it is already implemented externally with the shunt regulator on the secondary side of the DC-DC controller (see Figure 2). Therefore the FB pin must be strapped to ARTN and the output transistor of the opto-coupler has to be connected on the COMP pin where an internal 5 kW pull-up resistor is tied to the VDDL supply (see Figure 14). An internal linear regulator steps down the VPORTP voltage to a 9 V output on the VDDH pin. VDDH supplies the internal gate driver circuit which drives the GATE pin and the gate of the external power MOSFET. The NCP1082 gate driver supports an external MOSFET with high Vth and high input gate capacitance. A second LDO regulator steps down the VDDH voltage to a 3.3 V output on VDDL. VDDL powers the analog circuitry of the DC-DC controller. In order to prevent uncontrolled operations, both regulators include power-on-reset (POR) detectors which prevent the DC-DC controller from operating when either VDDH or VDDL is too low. In addition, an over-voltage lockout (OVLO) on the VDDH supply disables the gate driver in case of an open-loop converter with a configuration using the bias winding of the transformer (see Figure 4). Both VDDH and VDDL regulators turn on as soon as VPORT reaches the Vuvlo_on threshold. Soft-Start The soft-start function provided by the NCP1082 allows the output voltage to ramp up in a controlled fashion, eliminating output voltage overshoot. This function is programmed by connecting a capacitor Css between the SS and ARTN pins. While the DC-DC controller is in POR, the capacitor Css is fully discharged. After coming out of POR, an internal current source of 5 mA typically starts charging the capacitor Css to initiate soft-start. When the voltage on SS pin has reached 0.45 V (typical), the gate driver is enabled and DC-DC operation starts with a duty cycle limit which increases with the SS pin voltage. The soft-start function is finished when the SS pin voltage goes above 1.6 V for which the duty cycle limit reaches its maximum value of 80 percent. Soft-start can be programmed by using the following equation: Error Amplifier In non-isolated converter topologies, the high gain internal error amplifier of the NCP1082 and the internal 1.2 V reference voltage regulate the DC-DC output voltage. In this configuration, the feedback loop compensation network should be inserted between the FB and COMP pins as shown in Figures 3, 4 and 5. tss(ms) + 0.23 http://onsemi.com 14 Css(nf) NCP1082 Current Limit Comparator conduction mode (CCM) and when the duty cycle is close or above 50 percent, the NCP1082 integrates a current slope compensation circuit. The amplitude of the added slope compensation is typically 110 mV over one cycle. As an example, for an operating switching frequency of 250 kHz, the internal slope provided by the NCP1082 is 27.5 mV/ mA typically. The NCP1082 current limit block behind the CS pin senses the current flowing in the external MOSFET for current mode control and cycle-by-cycle current limit. This is performed by the current limit comparator which, on the CS pin, senses the voltage across the external Rcs resistor located between the source of the MOSFET and the ARTN pin. The NCP1082 also provides a blanking time function on CS pin which ensures that the current limit and PWM comparators are not prematurely trigged by the current spike that occurs when the switching MOSFET turns on. DC-DC Controller Oscillator The frequency is configured with the Rosc resistor inserted between OSC and ARTN, and is defined by the following equation: R OSC(kW) + Slope Compensation Circuitry To overcome sub-harmonic oscillations and instability problems that exist with converters running in continuous 38600 F OSC(kHz) The duty cycle limit is fixed internally at 80 percent. http://onsemi.com 15 NCP1082 PACKAGE DIMENSIONS TSSOP-20 EP CASE 948AB-01 ISSUE O D B B DETAIL B 20 e/2 0.20 C A-B D 11 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.07 IN EXCESS OF THE LEAD WIDTH AT MMC. DAMBAR CANNOT BE LOACTED ON THE LOWER RADIUS OR THE FOOT OF THE LEAD. 4. DIMENSIONS b, b1, c, c1 TO BE MEASURED BETWEEN 0.10 AND 0.25 FROM LEAD TIP. 5. DATUMS A AND B ARE ARE DETERMINED AT DATUM H. DATUM H IS LOACTED AT THE MOLD PARTING LINE AND COINCIDENT WITH LEAD WHERE THE LEAD EXITS THE PLASTIC BODY. 6. DIMENSION D DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSION E1 DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.15 PER SIDE. D AND E1 ARE DETERMINED AT DATUM H. 2X 10 TIPS E1 DETAIL B EEE EEE EEE PIN 1 REFERENCE 1 E b b1 IIII IIII IIII D c c1 10 e 20X A SECTION B-B b 0.10 TOP VIEW M C A-B D A2 B 0.05 C B A DETAIL A END VIEW 0.08 C 20X DIM A A1 A2 b b1 c c1 D E E1 e L L2 M P P1 M SIDE VIEW A1 C SEATING PLANE H L2 P SEATING PLANE GAUGE PLANE L C DETAIL A MILLIMETERS MAX MIN --1.10 0.05 0.15 0.85 0.95 0.19 0.30 0.19 0.25 0.09 0.20 0.09 0.16 6.40 6.60 6.40 BSC 4.30 4.50 0.65 BSC 0.50 0.70 0.25 BSC 0_ 8_ --4.20 --3.00 SOLDERING FOOTPRINT* P1 4.30 BOTTOM VIEW 6.76 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. 20X 0.98 3.10 0.65 PITCH The product described herein may be covered by one or more US patents pending. 20X 0.35 DIMENSIONS: MILLIMETERS ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 16 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP1082/D