Type 168/185 Metallized Polyester Radial Lead Capacitors Radial Box Metallized Polyester Capacitors for Automatic Insertion The Type 168/185 series radial lead metallized polyester box capacitors are available in bulk (Type 168) or on ammo pack or tape and reel (Type 185). These capacitors are constructed in rugged rectangular plastic cases and all come with 5.0 mm (0.197") lead spacing. They are good for general purpose applications such as bypass, decoupling, energy storage/discharge and arc suppression. Highlights * * * * * * * Case and epoxy fill meets UL94V-0 5.0 mm (0.197") lead spacing Bulk, tape and reel or ammo pack Non-inductively wound Non-polar Low leakage Lead material: Tinned copper wire Specifications RoHS Compliant Capacitance Range: Voltage Range: Capacitance Tolerance: Operating Temperature Range: Dielectric Withstand Voltage: Dissipation Factor (DF): 0.001 F to 1.0 F 50 Vdc to 400 Vdc 5%, 10%, 20% -55 C to +125 C (with 50% Vdc derating >85 C) 1.6 x rated voltage for 2 sec @ +25 C 5 C tan x 10 -4 at 25 C 5 C kHz C 0.1 F C > 0.1 F 1 100 100 10 150 150 100 300 Total Self Inductance (L): Approximately 7 nH Long Term Stability (after two years): Capacitance change C/C 3% under standard environmental conditions Maximum Pulse Rise Time (dv/dt): Vn Capacitance V/s 50 4 63 8 100 C > .0068 F 10 .0033 F < C < .0068 F 15 C .0033 F 30 250 44 400 100 If the working voltage (V) is less than the nominal voltage (Vn), the capacitor can work at higher dv/dt. In this case, the maximum value allowed is obtained by multiplying the above value with the ratio Vn/V. CDE Cornell Dubilier * 1605 E. Rodney French Blvd. * New Bedford, MA 02744 * Phone: (508)996-8561 * Fax: (508)996-3830 * www.cde.com Type 168/185 Metallized Polyester Radial Lead Capacitors Test Method and Performance Capacitor Outline Drawing Insulation Resistance Test Conditions Temperature: 25 C 5 C Voltage Charge Time: 1 minute Voltage Charge: 10 Vdc for Vn < 100 Vdc 100 Vdc for Vn 100 Vdc Performance For Vn > 100 Vdc: C 0.33 F, 15,000 M C > 0.33 F, 5,000 S For Vn 100 Vdc: C 0.33 F, 30,000 M C > 0.33 F, 10,000 S Damp Heat Test Test Conditions Temperature: +40 C Relative Humidity: 95% Test Duration: 21 days Performance Capacitance Change C/C: 5% DF Change tg: 0.005 (10 KHz) Insulation Resistance: 50% of limit value Life Test Test Conditions REF Temperature: +85 C Test Duration: 2000 hrs Voltage Applied: 1.25 x Vn Performance Capacitance Change C/C: 2% DF Change tg: 30 x 10-4 at 10 kHz Insulation Resistance: 50% of limit value T L Max Max H Max .217 .039 (5.5 1.0 mm) S .015 (0.4 mm) Od .003 (0.076) Lead length shown is as supplied on the 168 Series Soldering Test Conditions Soldering Temperature: 260 C 5 C Soldering Duration: 10 sec 1 sec Performance Capacitance Change C/C: 2% DF Change tg: 30 x 10-4 at 10 kHz Insulation Resistance: limit value Ratings RoHS Compliant Catalog Tape & Reel Cap Part Number Ammo Pack (F) L Inches 168104*50A-F 185104*50#A>-F 0.10 0.283 168154*50A-F 185154*50#A>-F 0.15 168224*50C-F 185224*50#C>-F 0.22 168334*50C-F 185334*50#C>-F 168474*50H-F 185474*50#H>-F T Millimeters H S Od L T H S Od 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 0.33 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 0.47 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 50 Vdc 168684*50F-F 185684*50#F>-F 0.68 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6 168824*50G-F 185824*50#G>-F 0.82 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6 168105*50G-F 185105*50#G>-F 1.00 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6 63 Vdc 168473*63A-F 185473*63#A>-F 0.047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168563*63A-F 185563*63#A>-F 0.056 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168683*63A-F 185683*63#A>-F 0.068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168823*63A-F 185823*63#A>-F 0.082 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168104*63A-F 185104*63#A>-F 0.10 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168154*63C-F 185154*63#C>-F 0.15 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168184*63C-F 185184*63#C>-F 0.18 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168224*63C-F 185224*63#C>-F 0.22 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168274*63C-F 185274*63#C>-F 0.27 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168334*63H-F 185334*63#H>-F 0.33 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168474*63H-F 185474*63#H>-F 0.47 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168684*63F-F 185684*63#F>-F 0.68 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6 168105*63G-F 185105*63#G>-F 1.00 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6 * Indicates capacitance tolerance: J = 5%, K = 10%, M = 20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack > Indicates tooling code: A = 16.5 mm, B = 18.5 mm (See H dimension in taping specifications) CDE Cornell Dubilier * 1605 E. Rodney French Blvd. * New Bedford, MA 02744 * Phone: (508)996-8561 * Fax: (508)996-3830 * www.cde.com Type 168/185 Metallized Polyester Radial Lead Capacitors Catalog Tape & Reel Cap Part Number Ammo Pack (F) Inches L T Millimeters H S Od L T H S Od 100 Vdc 168102*100A-F 185102*100#A>-F 0.0010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168152*100A-F 185152*100#A>-F 0.0015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168222*100A-F 185222*100#A>-F 0.0022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168272*100A-F 185272*100#A>-F 0.0027 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168332*100A-F 185332*100#A>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168392*100A-F 185392*100#A>-F 0.0039 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168472*100A-F 185472*100#A>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168562*100A-F 185562*100#A>-F 0.0056 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168682*100A-F 185682*100#A>-F 0.0068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168822*100A-F 185822*100#A>-F 0.0082 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168103*100A-F 185103*100#A>-F 0.010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168153*100A-F 185153*100#A>-F 0.015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168183*100A-F 185183*100#A>-F 0.018 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168223*100A-F 185223*100#A>-F 0.022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168273*100A-F 185273*100#A>-F 0.027 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168333*100C-F 185333*100#C>-F 0.033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168393*100C-F 185393*100#C>-F 0.039 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168473*100C-F 185473*100#C>-F 0.047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168683*100H-F 185683*100#H>-F 0.068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168104*100H-F 185104*100#H>-F 0.10 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 9.5 168154*100F-F 185154*100#F>-F 0.15 0.283 0.177 0.374 0.197 0.024 7.2 4.5 5.0 0.6 168224*100G-F 185224*100#G>-F 0.22 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10.0 5.0 0.6 168332*250A-F 185332*250#A>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168472*250A-F 185472*250#A>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168682*250A-F 185682*250#A>-F 0.0068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168103*250A-F 185103*250#A>-F 0.010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168153*250A-F 185153*250#A>-F 0.015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168223*250C-F 185223*250#C>-F 0.022 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168333*250C-F 185333*250#C>-F 0.033 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 250 Vdc 168473*250F-F 185473*250#F>-F 0.047 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6 168683*250F-F 185683*250#F>-F 0.068 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6 168104*250G-F 185104*250#G>-F 0.100 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6 400 Vdc 168102*400A-F 185102*400#A>-F 0.001 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168152*400A-F 185152*400#A>-F 0.0015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168222*400A-F 185222*400#A>-F 0.0022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168332*400C-F 185332*400#C>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168472*400C-F 185472*400#C>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168682*400C-F 185682*400#C>-F 0.0068 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168103*400F-F 185103*400#F>-F 0.010 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168153*400F-F 185153*400#F>-F 0.015 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6 168223*400G-F 185223*400#G>-F 0.022 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6 * Indicates capacitance tolerance: J = 5%, K = 10%, M = 20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack > Indicates tooling code: A = 16.5 mm, B = 18.5 mm (See H dimension in taping specification) CDE Cornell Dubilier * 1605 E. Rodney French Blvd. * New Bedford, MA 02744 * Phone: (508)996-8561 * Fax: (508)996-3830 * www.cde.com Type 168/185 Metallized Polyester Radial Lead Capacitors Tape Specification - 5.0 mm Lead Spacing Standard EIA-468-B Item Code Millimeters Inches Lead-to-Lead Distance P 5.0+0.6 -0.2 .197+.024 -.040 Feed Hole Pitch P0 12.7 .5 Pitch of Component P1 12.7 .5.039 Hole Center to Lead P2 2.540.7 .100.028 Feed Hole Center to P3 6.351.3 .250.051 0.3 Case Thickness Quantity Quantity T Reeled Ammo Pack .012 1.0 Component Center Component Alignment, F-R h 02.0 0.079 Tape Width W .709+.039 -.004 Hold-down Tape Width W0 6.0 min .236 min Hole Position W1 9.0+0.75 -0.05 .355+.030 -.001 Hold-down Tape Position W2 3.0 Max .118 Max Height of Component H > > D0 4.00.3 .157.012 18+1.0 -0.1 2500 2000 3.5 1800 1500 4.5 1400 1300 5 1200 1000 6 1000 800 > The H dimension depends on the insertion equipment used. Specify the proper tooling code as indicated below. Tooling from Tape Center Feed Hole Diameter 2.5 H Dimensions Code Millimeters Inches A 16.5 0.75 .6790.030 B 18.50.75 .7280.030 Part Numbering System for Auto Insertion 168/185 104 K 100 R H Packaging Series 185 Capacitance Tolerance -F *Tooling RoHS Type Internal Code Compliant Voltage (#) Code (>) Designation Letter A 102 = .001 F J = 5% 50 = 50 Vdc A = Ammo 103 = .01 F K = 10% 63 = 63 Vdc R = Tape & Reel 104 = .1 F M = 20% 100 = 100 Vdc 105 = 1.0 F B B 250 = 250 Vdc 400 = 400 Vdc * Tooling code (>) depends on the users insertion equipment requirements. See table for available options. CDE Cornell Dubilier * 1605 E. Rodney French Blvd. * New Bedford, MA 02744 * Phone: (508)996-8561 * Fax: (508)996-3830 * www.cde.com Type 168/185 Metallized Polyester Radial Lead Capacitors Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and data (collectively, the "Information") in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements ("Cornell Dubilier") has of operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter - and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required. CDE Cornell Dubilier * 1605 E. Rodney French Blvd. * New Bedford, MA 02744 * Phone: (508)996-8561 * Fax: (508)996-3830 * www.cde.com