1CY74FCT162H952 T Data sheet acquired from Cypress Semiconductor Corporation. Data sheet modified to remove devices not offered. CY74FCT16952T CY74FCT162952T CY74FCT162H952T 16-Bit Registered Transceivers SCCS065C - August 1994 - Revised September 2001 Features Functional Description * Ioff supports partial-power-down mode operation * Edge-rate control circuitry for significantly improved noise characteristics * Typical output skew < 250 ps * ESD > 2000V * TSSOP (19.6-mil pitch) and SSOP (25-mil pitch) packages * Industrial temperature range of -40C to +85C * VCC = 5V 10% CY74FCT16952T Features: * 64 mA sink current, 32 mA source current * Typical VOLP (ground bounce) <1.0V at VCC = 5V, TA = 25C These 16-bit registered transceivers are high-speed, low-power devices. 16-bit operation is achieved by connecting the control lines of the two 8-bit registered transceivers together. For data flow from bus A-to-B, CEAB must be LOW to allow data to be stored when CLKAB transitions from LOW-to-HIGH. The stored data will be present on the output when OEAB is LOW. Control of data from B-to-A is similar and is controlled by using the CEBA, CLKBA, and OEBA inputs. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The CY74FCT16952T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162952T has 24-mA balanced output drivers with current-limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162952T is ideal for driving transmission lines. CY74FCT162952T Features: * Balanced 24 mA output drivers * Reduced system switching noise * Typical VOLP (ground bounce) <0.6V at VCC = 5V, TA= 25C CY74FCT162H952T Features: * Bus hold retains last active state * Eliminates the need for external pull-up or pull-down resistors The CY74FCT162H952T is a 24-mA balanced output part that has "bus hold" on the data inputs. The device retains the input's last state whenever the input goes to high impedance. This eliminates the need for pull-up/down resistors and prevents floating inputs. Pin Configuration Logic Block Diagrams SSOP/TSSOP Top View 1 OEAB 2 CEBA 1 CEBA 1 CLKBA 2 OEAB 1 CEAB 2 CEAB 1 CLKAB 1A1 2 OEBA C CE D 1B1 C CE D 2A1 TO 7 OTHER CHANNELS 3 4 54 53 1 CEBA 5 52 1B1 1A2 VCC 6 51 1B2 7 50 VCC 1A3 8 9 49 48 1B3 47 46 45 1B5 GND 1 1A6 10 11 12 1A7 13 44 1B7 1A8 14 43 1B8 2A1 15 42 2B1 2A2 16 17 41 40 2B2 GND 2A4 18 39 GND 19 38 2B4 2A5 20 21 37 36 2B5 2A6 VCC 22 35 VCC 2A7 23 34 2B7 2A8 24 25 33 32 2B8 GND 2 CEAB 26 31 2 CEBA 2 CLKAB 27 30 2 CLKBA 2 OEAB 28 29 2 OEBA 1A4 1A5 C CE D 2B C CE D FCT16952-1 1 OEBA GND 1A1 2 CLKAB 1 OEBA 56 55 1 CEAB 2 CLKBA 1 OEAB 1 2 1 CLKAB FCT16952-2 TO 7 OTHER CHANNELS 2A3 1 CLKBA GND 1B4 GND 1B6 2B3 2B6 GND FCT16952-3 Copyright (c) 2001, Texas Instruments Incorporated CY74FCT16952T CY74FCT162952T CY74FCT162H952T Maximum Ratings[5, 6] Pin Description Name Description (Above which the useful life may be impaired. For user guidelines, not tested.) OEAB A-to-B Output Enable Input (Active LOW) OEBA B-to-A Output Enable Input (Active LOW) Storage Temperature ................................. -55C to +125C CEAB A-to-B Clock Enable Input (Active LOW) CEBA B-to-A Clock Enable Input (Active LOW) Ambient Temperature with Power Applied............................................. -55C to +125C CLKAB A-to-B Clock Input CLKBA B-to-A Clock Input A A-to-B Data Inputs or B-to-A Three-State Outputs[1] B B-to-A Data Inputs or A-to-B Three-State Outputs[1] DC Input Voltage ........................................... -0.5V to +7.0V DC Output Voltage......................................... -0.5V to +7.0V DC Output Current (Maximum Sink Current/Pin) ........................-60 to +120 mA Power Dissipation .......................................................... 1.0W Static Discharge Voltage............................................>2001V (per MIL-STD-883, Method 3015) Function Table[2, 3] For A-to-B (Symmetric with B-to-A) Operating Range Inputs Outputs CEAB CLKAB OEAB A B H X L X B[4] X L L X B[4] L L L L L L H H H X Z X X Range Industrial Ambient Temperature VCC -40C to +85C 5V 10% Notes: 1. On the CY74FCT162H952T these pins have bus hold. 2. A-to-B data flow is shown: B-to-A data flow is similar but uses, CEBA, CLKBA, and OEBA. 3. H = HIGH Voltage Level. L = LOW Voltage Level. X = Don't Care. 4. 5. 6. = LOW-to-HIGH Transition. Z = HIGH Impedance. Level of B before the indicated steady-state input conditions were established. Operation beyond the limits set forth may impair the useful life of the device. Unless otherwise noted, these limits are over the operating free-air temperature range. Unused inputs must always be connected to an appropriate logic voltage level, preferably either VCC or ground. 2 CY74FCT16952T CY74FCT162952T CY74FCT162H952T Electrical Characteristics Over the Operating Range Parameter Description VIH Input HIGH Voltage VIL Input LOW Voltage Test Conditions Min. Input Hysteresis VIK Input Clamp Diode Voltage IIH Input HIGH Current 100 VCC=Min., IIN= -18 mA Standard Input LOW Current Unit V 0.8 -0.7 VCC=Max., VI=VCC V mV -1.2 V 1 A 100 Bus Hold IIL Max. 2.0 [8] VH Typ.[7] Standard VCC=Max., VI=GND Bus Hold [9] VCC=Min. 1 A 100 A VI=2.0V -50 A VI=0.8V +50 A IBBH IBBL Bus Hold Sustain Current on Bus Hold Input IBHHO IBHLO Bus Hold Overdrive Current on Bus Hold Input[9] VCC=Max., VI=1.5V IOZH High Impedance Output Current (Three-State Output pins) IOZL IOS TBD mA VCC=Max., VOUT=2.7V 1 A High Impedance Output Current (Three-State Output pins) VCC=Max., VOUT=0.5V 1 A Short Circuit Current[10] VCC=Max., VOUT=GND -80 -200 mA Current[10] VCC=Max., VOUT=2.5V -50 -180 mA 1 A Max. Unit IO Output Drive IOFF Power-Off Disable -140 VCC=0V, VOUT4.5V[11] Output Drive Characteristics for CY74FCT16952T Parameter VOH VOL Min. Typ.[7] VCC=Min., IOH= -3 mA 2.5 3.5 V VCC=Min., IOH= -15 mA 2.4 3.5 V VCC=Min., IOH= -32 mA 2.0 3.0 Description Output HIGH Voltage Output LOW Voltage Test Conditions VCC=Min., IOL=64 mA V 0.2 0.55 V Typ.[7] Max. Unit Output Drive Characteristics for CY74FCT162952T, CY74FCT162H952T Parameter Description Test Conditions Min. IODL Output LOW Current[10] VCC=5V, VIN=VIH or VIL, VOUT=1.5V 60 115 150 mA IODH Output HIGH Current[10] VCC=5V, VIN=VIH or VIL, VOUT=1.5V -60 -115 -150 mA VOH Output HIGH Voltage VCC=Min., IOH= -24 mA 2.4 3.3 VOL Output LOW Voltage VCC=Min., IOL=24 mA V 0.3 0.55 V Typ.[7] Max. Unit 4.5 6.0 pF Capacitance[8] (TA = +25C, f = 1.0 MHz) Parameter CIN Description Input Capacitance Test Conditions VIN = 0V COUT Output Capacitance VOUT = 0V 5.5 8.0 pF Note: 7. Typical values are at VCC= 5.0V, TA= +25C ambient. 8. This parameter is specified but not tested. 9. Pins with bus hold are described in the Pin Description. 10. Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or sample and hold techniques are preferable in order to minimize internal chip heating and more accurately reflect operational values. Otherwise prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parametric tests. In any sequence of parameter tests, IOS tests should be performed last. 11. Tested at +25C. 3 CY74FCT16952T CY74FCT162952T CY74FCT162H952T Power Supply Characteristics Parameter Test Conditions[12] Description Typ.[7] Max. Unit 5 500 A 0.5 1.5 mA ICC Quiescent Power Supply Current VCC=Max. VIN<0.2V VIN>VCC-0.2V ICC Quiescent Power Supply Current VCC=Max. (TTL inputs HIGH) VIN=3.4V[13] ICCD Dynamic Power Supply Current[14] VCC=Max., One Input Toggling, VIN=VCC or 50% Duty Cycle, Outputs Open, VIN=GND OEAB or OEBA=GND 75 120 A/MHz IC Total Power Supply Current[15] VCC=Max., F1=5 MHz, F0 = 10 MHz (CLKAB) OEAB = CEAB = GND OEBA = VCC 50% Duty Cycle, Outputs Open, One Bit Toggling VIN=VCC or VIN=GND 0.8 1.7 mA VIN=3.4V or VIN=GND 1.3 3.2 VIN=VCC or VIN=GND 3.8 6.5[16] VIN=3.4V or VIN=GND 8.3 20.0[16] VCC=Max., f0=10 MHz (CLKAB) f1=2.5 MHz, OEAB = CEAB = GND OEBA = VCC 50% Duty Cycle, Outputs Open, Sixteen Bit Toggling Notes: 12. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 13. Per TTL driven input (VIN=3.4V); all other inputs at VCC or GND. 14. This parameter is not directly testable, but is derived for use in Total Power Supply calculations. = IQUIESCENT + IINPUTS + IDYNAMIC 15. IC IC = ICC+ICCDHNT+ICCD(f0/2 + f1N1) ICC = Quiescent Current with CMOS input levels ICC = Power Supply Current for a TTL HIGH input (VIN=3.4V) DH = Duty Cycle for TTL inputs HIGH NT = Number of TTL inputs at DH ICCD = Dynamic Current caused by an input transition pair (HLH or LHL) = Clock frequency for registered devices, otherwise zero f0 = Input signal frequency f1 N1 = Number of inputs changing at f1 All currents are in milliamps and all frequencies are in megahertz. 16. Values for these conditions are examples of the ICC formula. These limits are specified but not tested. 4 CY74FCT16952T CY74FCT162952T CY74FCT162H952T Switching Characteristics Over the Operating Range[17] CY74FCT16952AT CY74FCT162952AT CY74FCT162H952AT Parameter Description CY74FCT162952BT Min. Max. Min. Max. Unit Fig. No.[18] tPLH tPHL Propagation Delay CLKAB, CLKBA to B, A 2.0 10.0 2.0 7.5 ns 1, 5 tPZH tPZL Output Enable Time OEBA, OEAB to A, B 1.5 10.5 1.5 8.0 ns 1, 7, 8 tPHZ tPLZ Output Disable Time OEBA, OEAB to A, B 1.5 10.0 1.5 7.5 ns 1, 7, 8 tSU Set-Up Time, HIGH or LOW A, B to CLKAB, CLKBA 2.5 -- 2.5 -- ns 4 tH Hold Time, HIGH or LOW A, B to CLKAB, CLKBA 2.0 -- 1.5 -- ns 4 tSU Set-Up Time, HIGH or LOW CEAB, CEBA to CLKAB, CLKBA 3.0 -- 3.0 -- ns 4 tH Hold Time, HIGH or LOW CEAB, CEBA to CLKAB, CLKBA 2.0 -- 2.0 -- ns 4 tW Pulse Width HIGH or LOW CLKAB or CLKBA[19] 3.0 -- 3.0 -- ns 5 tSK(O) Output Skew[20] -- 0.5 -- 0.5 ns -- CY74FCT16952CT CY74FCT162H952CT Parameter Description Min. Max. Unit Fig. No.[18] tPLH tPHL Propagation Delay CLKAB, CLKBA to B, A 2.0 6.3 ns 1, 5 tPZH tPZL Output Enable Time OEBA, OEAB to A, B 1.5 7.0 ns 1, 7, 8 tPHZ tPLZ Output Disable Time OEBA, OEAB to A, B 1.5 6.5 ns 1, 7, 8 tSU Set-Up Time, HIGH or LOW A, B to CLKAB, CLKBA 2.5 -- ns 4 tH Hold Time, HIGH or LOW A, B to CLKAB, CLKBA 1.5 -- ns 4 tSU Set-Up Time, HIGH or LOW CEAB, CEBA to CLKAB, CLKBA 3.0 -- ns 4 tH Hold Time, HIGH or LOW CEAB, CEBA to CLKAB, CLKBA 2.0 -- ns 4 tW Pulse Width HIGH or LOW CLKAB or CLKBA[19] 3.0 -- ns 5 tSK(O) Output Skew[20] -- 0.5 ns -- Notes: 17. Minimum limits are specified but not tested on Propagation Delays. 18. See "Parameter Measurement Information" in the General Information section. 19. This parameter is specified but not tested. 20. Skew between any two outputs of the same package switching in the same direction. This parameter is ensured by design. 5 CY74FCT16952T CY74FCT162952T CY74FCT162H952T Ordering Information CY74FCT16952 Speed (ns) Ordering Code Package Name Package Type Operating Range 6.3 CY74FCT16952CTPACT Z56 56-Lead (240-Mil) TSSOP Industrial 10.0 CY74FCT16952ATPVC/PVCT O56 56-Lead (300-Mil) SSOP Industrial Ordering Information CY74FCT162952 Speed (ns) 7.5 10.0 Ordering Code Package Name Package Type CY74FCT162952BTPVC O56 56-Lead (300-Mil) SSOP 74FCT162952BTPVCT O56 56-Lead (300-Mil) SSOP 74FCT162952ATPACT Z56 56-Lead (240-Mil) TSSOP Operating Range Industrial Industrial Ordering Information CY74FCT162H952 Speed (ns) Ordering Code Package Name Package Type Operating Range 6.3 74FCT162H952CTPVC/PVCT O56 56-Lead (300-Mil) SSOP Industrial 10.0 74FCT162H952ATPACT Z56 56-Lead (240-Mil) TSSOP Industrial 6 CY74FCT16952T CY74FCT162952T CY74FCT162H952T Package Diagrams 56-Lead Shrunk Small Outline Package O56 56-Lead Thin Shrunk Small Outline Package Z56 7 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2001, Texas Instruments Incorporated