LM1117DT-ADJ - National Semiconductor

LM1117/LM1117I

800mA Low-Dropout Linear Regulator

General Description

The LM1117 is a series of low dropout voltage regulators with

a dropout of 1.2V at 800mA of load current. It has the same

pin-out as National Semiconductor's industry standard

LM317.

The LM1117 is available in an adjustable version, which can

set the output voltage from 1.25V to 13.8V with only two ex-

ternal resistors. In addition, it is also available in five fixed

voltages, 1.8V, 2.5V, 2.85V, 3.3V, and 5V.

The LM1117 offers current limiting and thermal shutdown. Its

circuit includes a zener trimmed bandgap reference to assure

output voltage accuracy to within ±1%.

The LM1117 series is available in LLP, TO-263, SOT-223,

TO-220, and TO-252 D-PAK packages. A minimum of 10µF

tantalum capacitor is required at the output to improve the

transient response and stability.

Features

●Available in 1.8V, 2.5V, 2.85V, 3.3V, 5V, and Adjustable

Versions

●Space Saving SOT-223 and LLP Packages

●Current Limiting and Thermal Protection

●Output Current 800mA

●Line Regulation 0.2% (Max)

●Load Regulation 0.4% (Max)

●Temperature Range

—LM1117 0°C to 125°C

—LM1117I −40°C to 125°C

Applications

●2.85V Model for SCSI-2 Active Termination

●Post Regulator for Switching DC/DC Converter

●High Efficiency Linear Regulators

●Battery Charger

●Battery Powered Instrumentation

Typical Application

Active Terminator for SCSI-2 Bus

10091905

Fixed Output Regulator

10091928

PRODUCTION DATA information is current as of

publication date. Products conform to specifications per

the terms of the Texas Instruments standard warranty.

Production processing does not necessarily include

testing of all parameters.

Ordering Information

Package Temperature Range Part Number Packaging Marking Transport Media NSC

Drawing

3-lead SOT-223 0°C to +125°C LM1117MPX-ADJ N03A Tape and Reel MP04A

LM1117MPX-2.5 N13A Tape and Reel

LM1117MPX-2.85 N04A Tape and Reel

LM1117MPX-3.3 N05A Tape and Reel

LM1117MPX-5.0 N06A Tape and Reel

−40°C to +125°C LM1117IMPX-ADJ N03B Tape and Reel

LM1117IMPX-3.3 N05B Tape and Reel

LM1117IMPX-5.0 N06B Tape and Reel

3-lead TO-220 0°C to +125°C LM1117T-ADJ LM1117T-ADJ Rails T03B

LM1117T-1.8 LM1117T-1.8 Rails

LM1117T-2.5 LM1117T-2.5 Rails

LM1117T-3.3 LM1117T-3.3 Rails

LM1117T-5.0 LM1117T-5.0 Rails

3-lead TO-252 0°C to +125°C LM1117DTX-ADJ LM1117DT-ADJ Tape and Reel TD03B

LM1117DTX-1.8 LM1117DT-1.8 Tape and Reel

LM1117DTX-2.5 LM1117DT-2.5 Tape and Reel

LM1117DTX-3.3 LM1117DT-3.3 Tape and Reel

LM1117DTX-5.0 LM1117DT-5.0 Tape and Reel

−40°C to +125°C LM1117IDTX-ADJ LM1117IDT-ADJ Tape and Reel

LM1117IDTX-3.3 LM1117IDT-3.3 Tape and Reel

LM1117IDTX-5.0 LM1117IDT-5.0 Tape and Reel

8-lead LLP 0°C to +125°C LM1117LDX-ADJ 1117ADJ Tape and Reel LDC08A

LM1117LDX-1.8 1117-18 Tape and Reel

LM1117LDX-5.0 1117-50 Tape and Reel

−40°C to 125°C LM1117ILDX-ADJ 1117IAD Tape and Reel

LM1117ILDX-3.3 1117I33 Tape and Reel

LM1117ILDX-5.0 1117I50 Tape and Reel

TO-263 0°C to +125°C LM1117SX-ADJ LM1117SADJ Tape and Reel TS3B

LM1117SX-3.3 LM1117S3.3 Tape and Reel

LM1117SX-5.0 LM1117S5.0 Tape and Reel

LM1117/LM1117I

Block Diagram

10091901

Connection Diagrams

SOT-223

10091904

Top View

TO-220

10091902

Top View

TO-252

10091938

Top View

LM1117/LM1117I

TO-263

10091944

Top View

10091945

Side View

LLP

10091946

When using the LLP package

Pins 2, 3 & 4 must be connected together and

Pins 5, 6 & 7 must be connected together

Top View

LM1117/LM1117I

Absolute Maximum Ratings (Note 1)

If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for

availability and specifications.

Maximum Input Voltage (VIN to GND) 20V

Power Dissipation (Note 2) Internally Limited

Junction Temperature (TJ)

(Note 2)150°C

Storage Temperature Range -65°C to 150°C

Lead Temperature

TO-220 (T) Package 260°C, 10 sec

SOT-223 (IMP) Package 260°C, 4 sec

ESD Tolerance (Note 3) 2000V

Operating Ratings (Note 1)

Input Voltage (VIN to GND) 15V

Junction Temperature Range (TJ)(Note 2)

LM1117 0°C to 125°C

LM1117I −40°C to 125°C

LM1117 Electrical Characteristics

Typicals and limits appearing in normal type apply for TJ = 25°C. Limits appearing in Boldface type apply over the entire junction

temperature range for operation, 0°C to 125°C.

Symbol Parameter Conditions Min

(Note 5)

Typ

(Note 4)

Max

(Note 5)Units

VREF Reference Voltage LM1117-ADJ

IOUT = 10mA, VIN-VOUT = 2V, TJ = 25°C

10mA ≤ IOUT ≤ 800mA, 1.4V ≤ VIN-VOUT ≤

10V

1.238

1.225

1.250

1.262

1.270

VOUT Output Voltage LM1117-1.8

IOUT = 10mA, VIN = 3.8V, TJ = 25°C

0 ≤ IOUT ≤ 800mA, 3.2V ≤ VIN ≤ 10V

1.782

1.746

1.800

1.818

1.854

LM1117-2.5

IOUT = 10mA, VIN = 4.5V, TJ = 25°C

0 ≤ IOUT ≤ 800mA, 3.9V ≤ VIN ≤ 10V

2.475

2.450

2.500

2.525

2.550

LM1117-2.85

IOUT = 10mA, VIN = 4.85V, TJ = 25°C

0 ≤ IOUT ≤ 800mA, 4.25V ≤ VIN ≤ 10V

0 ≤ IOUT ≤ 500mA, VIN = 4.10V

2.820

2.790

2.850

2.880

2.910

LM1117-3.3

IOUT = 10mA, VIN = 5V TJ = 25°C

0 ≤ IOUT ≤ 800mA, 4.75V≤ VIN ≤ 10V

3.267

3.235

3.300

3.333

3.365

LM1117-5.0

IOUT = 10mA, VIN = 7V, TJ = 25°C

0 ≤ IOUT ≤ 800mA, 6.5V ≤ VIN ≤ 12V

4.950

4.900

5.000

5.050

5.100

LM1117/LM1117I

Symbol Parameter Conditions Min

(Note 5)

Typ

(Note 4)

Max

(Note 5)Units

ΔVOUT Line Regulation

(Note 6)

LM1117-ADJ

IOUT = 10mA, 1.5V ≤ VIN-VOUT ≤ 13.75V

0.035

0.2

LM1117-1.8

IOUT = 0mA, 3.2V ≤ VIN ≤ 10V

1 6mV

LM1117-2.5

IOUT = 0mA, 3.9V ≤ VIN ≤ 10V

1 6mV

LM1117-2.85

IOUT = 0mA, 4.25V ≤ VIN ≤ 10V

LM1117-3.3

IOUT = 0mA, 4.75V ≤ VIN ≤ 15V

LM1117-5.0

IOUT = 0mA, 6.5V ≤ VIN ≤ 15V

ΔVOUT Load Regulation

(Note 6)

LM1117-ADJ

VIN-VOUT = 3V, 10 ≤ IOUT ≤ 800mA

0.2

0.4

LM1117-1.8

VIN = 3.2V, 0 ≤ IOUT ≤ 800mA

1 10 mV

LM1117-2.5

VIN = 3.9V, 0 ≤ IOUT ≤ 800mA

1 10 mV

LM1117-2.85

VIN = 4.25V, 0 ≤ IOUT ≤ 800mA

LM1117-3.3

VIN = 4.75V, 0 ≤ IOUT ≤ 800mA

LM1117-5.0

VIN = 6.5V, 0 ≤ IOUT ≤ 800mA

VIN-V OUT Dropout Voltage

(Note 7)

IOUT = 100mA 1.10 1.20 V

IOUT = 500mA 1.15 1.25 V

IOUT = 800mA 1.20 1.30 V

ILIMIT Current Limit VIN-VOUT = 5V, TJ = 25°C 800 1200 1500 mA

Minimum Load Current

(Note 8)

LM1117-ADJ

VIN = 15V

1.7

Quiescent Current LM1117-1.8

VIN ≤ 15V

5 10 mA

LM1117-2.5

VIN ≤ 15V

5 10 mA

LM1117-2.85

VIN ≤ 10V

LM1117-3.3

VIN ≤ 15V

LM1117-5.0

VIN ≤ 15V

Thermal Regulation TA = 25°C, 30ms Pulse 0.01 0.1 %/W

Ripple Regulation fRIPPLE =1 20Hz, VIN-VOUT = 3V VRIPPLE =

1VPP

60 75 dB

Adjust Pin Current 60 120 μA

Adjust Pin Current

Change

10 ≤ IOUT≤ 800mA,

1.4V ≤ VIN-VOUT ≤ 10V

0.2

μA

Temperature Stability 0.5 %

Long Term Stability TA = 125°C, 1000Hrs 0.3 %

LM1117/LM1117I

Symbol Parameter Conditions Min

(Note 5)

Typ

(Note 4)

Max

(Note 5)Units

RMS Output Noise (% of VOUT), 10Hz ≤ f ≤10kHz 0.003 %

Thermal Resistance

Junction-to-Case

3-Lead SOT-223 15.0 °C/W

3-Lead TO-220 3.0 °C/W

3-Lead TO-252 10 °C/W

Thermal Resistance

Junction-to-Ambient

(No air flow)

3-Lead SOT-223 (No heat sink) 136 °C/W

3-Lead TO-220 (No heat sink) 79 °C/W

3-Lead TO-252 (Note 9) (No heat sink) 92 °C/W

3-Lead TO-263 55 °C/W

8-Lead LLP(Note 10) 40 °C/W

LM1117I Electrical Characteristics

Typicals and limits appearing in normal type apply for TJ = 25°C. Limits appearing in Boldface type apply over the entire junction

temperature range for operation, −40°C to 125°C.

Symbol Parameter Conditions Min

(Note 5)

Typ

(Note 4)

Max

(Note 5)Units

VREF Reference Voltage LM1117I-ADJ

IOUT = 10mA, VIN-VOUT = 2V, TJ = 25°C

10mA ≤ IOUT ≤ 800mA, 1.4V ≤ VIN-VOUT ≤

10V

1.238

1.200

1.250

1.262

1.290

VOUT Output Voltage LM1117I-3.3

IOUT = 10mA, VIN = 5V, TJ = 25°C

0 ≤ IOUT ≤ 800mA, 4.75V ≤ VIN ≤ 10V

3.267

3.168

3.300

3.333

3.432

LM1117I-5.0

IOUT = 10mA, VIN = 7V, TJ = 25°C

0 ≤ IOUT ≤ 800mA, 6.5V ≤ VIN ≤ 12V

4.950

4.800

5.000

5.050

5.200

ΔVOUT Line Regulation

(Note 6)

LM1117I-ADJ

IOUT = 10mA, 1.5V ≤ VIN-VOUT ≤ 13.75V

0.035

0.3

LM1117I-3.3

IOUT = 0mA, 4.75V ≤ VIN ≤ 15V

LM1117I-5.0

IOUT = 0mA, 6.5V ≤ VIN ≤ 15V

ΔVOUT Load Regulation

(Note 6)

LM1117I-ADJ

VIN-VOUT = 3V, 10 ≤ IOUT ≤ 800mA

0.2

0.5

LM1117I-3.3

VIN = 4.75V, 0 ≤ IOUT ≤ 800mA

LM1117I-5.0

VIN = 6.5V, 0 ≤ IOUT ≤ 800mA

VIN-V OUT Dropout Voltage

(Note 7)

IOUT = 100mA 1.10 1.30 V

IOUT = 500mA 1.15 1.35 V

IOUT = 800mA 1.20 1.40 V

ILIMIT Current Limit VIN-VOUT = 5V, TJ = 25°C 800 1200 1500 mA

Minimum Load Current

(Note 8)

LM1117I-ADJ

VIN = 15V

1.7

Quiescent Current LM1117I-3.3

VIN ≤ 15V

LM1117I-5.0

VIN ≤ 15V

Thermal Regulation TA = 25°C, 30ms Pulse 0.01 0.1 %/W

LM1117/LM1117I

Symbol Parameter Conditions Min

(Note 5)

Typ

(Note 4)

Max

(Note 5)Units

Ripple Regulation fRIPPLE =1 20Hz, VIN-VOUT = 3V VRIPPLE =

1VPP

60 75 dB

Adjust Pin Current 60 120 μA

Adjust Pin Current

Change

10 ≤ IOUT≤ 800mA,

1.4V ≤ VIN-VOUT ≤ 10V

0.2

μA

Temperature Stability 0.5 %

Long Term Stability TA = 125°C, 1000Hrs 0.3 %

RMS Output Noise (% of VOUT), 10Hz ≤ f ≤10kHz 0.003 %

Thermal Resistance

Junction-to-Case

3-Lead SOT-223 15.0 °C/W

3-Lead TO-252 10 °C/W

Thermal Resistance

Junction-to-Ambient

No air flow)

3-Lead SOT-223 (No heat sink) 136 °C/W

3-Lead TO-252 (No heat sink)(Note 9) 92 °C/W

8-Lead LLP(Note 10) 40 °C/W

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.

Note 2: The maximum power dissipation is a function of TJ(max) , θJA, and TA. The maximum allowable power dissipation at any ambient temperature is

PD = (TJ(max)–TA)/θJA. All numbers apply for packages soldered directly into a PC board.

Note 3: For testing purposes, ESD was applied using human body model, 1.5kΩ in series with 100pF.

Note 4: Typical Values represent the most likely parametric norm.

Note 5: All limits are guaranteed by testing or statistical analysis.

Note 6: Load and line regulation are measured at constant junction room temperature.

Note 7: The dropout voltage is the input/output differential at which the circuit ceases to regulate against further reduction in input voltage. It is measured when

the output voltage has dropped 100mV from the nominal value obtained at VIN = VOUT +1.5V.

Note 8: The minimum output current required to maintain regulation.

Note 9: Minimum pad size of 0.038in2

Note 10: Thermal Performance for the LLP was obtained using JESD51-7 board with six vias and an ambient temperature of 22°C. For information about improved

thermal performance and power dissipation for the LLP, refer to Application Note AN-1187.

LM1117/LM1117I

Typical Performance Characteristics

Dropout Voltage (VIN-V OUT)

10091922

Short-Circuit Current

10091923

Load Regulation

10091943

LM1117-ADJ Ripple Rejection

10091906

LM1117-ADJ Ripple Rejection vs. Current

10091907

Temperature Stability

10091925

LM1117/LM1117I

Adjust Pin Current

10091926

LM1117-2.85 Load Transient Response

10091908

LM1117-5.0 Load Transient Response

10091909

LM1117-2.85 Line Transient Response

10091910

LM1117-5.0 Line Transient Response

10091911

LM1117/LM1117I

Application Note

1.0 EXTERNAL CAPACITORS/STABILITY

1.1 Input Bypass Capacitor

An input capacitor is recommended. A 10µF tantalum on the input is a suitable input bypassing for almost all applications.

1.2 Adjust Terminal Bypass Capacitor

The adjust terminal can be bypassed to ground with a bypass capacitor (CADJ) to improve ripple rejection. This bypass capacitor

prevents ripple from being amplified as the output voltage is increased. At any ripple frequency, the impedance of the CADJ should

be less than R1 to prevent the ripple from being amplified:

1/(2π*fRIPPLE*CADJ) < R1

The R1 is the resistor between the output and the adjust pin. Its value is normally in the range of 100-200Ω. For example, with R1

= 124Ω and fRIPPLE = 120Hz, the CADJ should be > 11µF.

1.3 Output Capacitor

The output capacitor is critical in maintaining regulator stability, and must meet the required conditions for both minimum amount

of capacitance and ESR (Equivalent Series Resistance). The minimum output capacitance required by the LM1117 is 10µF, if a

tantalum capacitor is used. Any increase of the output capacitance will merely improve the loop stability and transient response.

The ESR of the output capacitor should range between 0.3Ω - 22Ω. In the case of the adjustable regulator, when the CADJ is used,

a larger output capacitance (22µf tantalum) is required.

2.0 OUTPUT VOLTAGE

The LM1117 adjustable version develops a 1.25V reference voltage, VREF, between the output and the adjust terminal. As shown

in Figure 1, this voltage is applied across resistor R1 to generate a constant current I1. The current IADJ from the adjust terminal

could introduce error to the output. But since it is very small (60µA) compared with the I1 and very constant with line and load

changes, the error can be ignored. The constant current I1 then flows through the output set resistor R2 and sets the output voltage

to the desired level.

For fixed voltage devices, R1 and R2 are integrated inside the devices.

10091917

FIGURE 1. Basic Adjustable Regulator

3.0 LOAD REGULATION

The LM1117 regulates the voltage that appears between its output and ground pins, or between its output and adjust pins. In some

cases, line resistances can introduce errors to the voltage across the load. To obtain the best load regulation, a few precautions

are needed.

Figure 2, shows a typical application using a fixed output regulator. The Rt1 and Rt2 are the line resistances. It is obvious that the

VLOAD is less than the VOUT by the sum of the voltage drops along the line resistances. In this case, the load regulation seen at the

RLOAD would be degraded from the data sheet specification. To improve this, the load should be tied directly to the output terminal

on the positive side and directly tied to the ground terminal on the negative side.

LM1117/LM1117I

10091918

FIGURE 2. Typical Application using Fixed Output Regulator

When the adjustable regulator is used (Figure 3), the best performance is obtained with the positive side of the resistor R1 tied

directly to the output terminal of the regulator rather than near the load. This eliminates line drops from appearing effectively in

series with the reference and degrading regulation. For example, a 5V regulator with 0.05Ω resistance between the regulator and

load will have a load regulation due to line resistance of 0.05Ω x IL. If R1 (=125Ω) is connected near the load, the effective line

resistance will be 0.05Ω (1+R2/R1) or in this case, it is 4 times worse. In addition, the ground side of the resistor R2 can be returned

near the ground of the load to provide remote ground sensing and improve load regulation.

10091919

FIGURE 3. Best Load Regulation using Adjustable Output Regulator

4.0 PROTECTION DIODES

Under normal operation, the LM1117 regulators do not need any protection diode. With the adjustable device, the internal resistance

between the adjust and output terminals limits the current. No diode is needed to divert the current around the regulator even with

capacitor on the adjust terminal. The adjust pin can take a transient signal of ±25V with respect to the output voltage without

damaging the device.

When a output capacitor is connected to a regulator and the input is shorted to ground, the output capacitor will discharge into the

output of the regulator. The discharge current depends on the value of the capacitor, the output voltage of the regulator, and rate

of decrease of VIN. In the LM1117 regulators, the internal diode between the output and input pins can withstand microsecond

surge currents of 10A to 20A. With an extremely large output capacitor (≥1000 µF), and with input instantaneously shorted to

ground, the regulator could be damaged.

In this case, an external diode is recommended between the output and input pins to protect the regulator, as shown in Figure 4.

LM1117/LM1117I

10091915

FIGURE 4. Regulator with Protection Diode

5.0 HEATSINK REQUIREMENTS

When an integrated circuit operates with an appreciable current, its junction temperature is elevated. It is important to quantify its

thermal limits in order to achieve acceptable performance and reliability. This limit is determined by summing the individual parts

consisting of a series of temperature rises from the semiconductor junction to the operating environment. A one-dimensional steady-

state model of conduction heat transfer is demonstrated in Figure 5. The heat generated at the device junction flows through the

die to the die attach pad, through the lead frame to the surrounding case material, to the printed circuit board, and eventually to

the ambient environment. Below is a list of variables that may affect the thermal resistance and in turn the need for a heatsink.

RθJC (Component

Variables)

Rθ CA (Application

Variables)

Leadframe Size & Material Mounting Pad Size,

Material, & Location

No. of Conduction Pins Placement of Mounting Pad

Die Size PCB Size & Material

Die Attach Material Traces Length & Width

Molding Compound Size

and Material

Adjacent Heat Sources

Volume of Air

Ambient Temperatue

Shape of Mounting Pad

10091937

FIGURE 5. Cross-sectional view of Integrated Circuit Mounted on a printed circuit board. Note that the case temperature

is measured at the point where the leads contact with the mounting pad surface

The LM1117 regulators have internal thermal shutdown to protect the device from over-heating. Under all possible operating

conditions, the junction temperature of the LM1117 must be within the range of 0°C to 125°C. A heatsink may be required depending

on the maximum power dissipation and maximum ambient temperature of the application. To determine if a heatsink is needed,

the power dissipated by the regulator, PD , must be calculated:

IIN = IL + IG

PD = (VIN-VOUT)I L + VINIG

Figure 6 shows the voltages and currents which are present in the circuit.

LM1117/LM1117I

10091916

FIGURE 6. Power Dissipation Diagram

The next parameter which must be calculated is the maximum allowable temperature rise, TR(max):

TR(max) = TJ(max)-TA(max)

where TJ(max) is the maximum allowable junction temperature (125°C), and TA(max) is the maximum ambient temperature which

will be encountered in the application.

Using the calculated values for TR(max) and PD, the maximum allowable value for the junction-to-ambient thermal resistance

(θJA) can be calculated:

θJA = TR(max)/PD

If the maximum allowable value for θJA is found to be ≥136°C/W for SOT-223 package or ≥79°C/W for TO-220 package or ≥92°

C/W for TO-252 package, no heatsink is needed since the package alone will dissipate enough heat to satisfy these requirements.

If the calculated value for θJA falls below these limits, a heatsink is required.

As a design aid, Table 1 shows the value of the θJA of SOT-223 and TO-252 for different heatsink area. The copper patterns that

we used to measure these θJAs are shown at the end of the Application Notes Section. Figure 7 and Figure 8 reflects the same

test results as what are in the Table 1

Figure 9 and Figure 10 shows the maximum allowable power dissipation vs. ambient temperature for the SOT-223 and TO-252

device. Figures Figure 11 and Figure 12 shows the maximum allowable power dissipation vs. copper area (in2) for the SOT-223

and TO-252 devices. Please see AN1028 for power enhancement techniques to be used with SOT-223 and TO-252 packages.

*Application Note AN-1187 discusses improved thermal performance and power dissipation for the LLP.

TABLE 1. θJA Different Heatsink Area

Layout Copper Area Thermal Resistance

Top Side (in2)* Bottom Side (in2)(θJA,°C/W) SOT-223 (θJA,°C/W) TO-252

1 0.0123 0 136 103

2 0.066 0 123 87

3 0.3 0 84 60

4 0.53 0 75 54

5 0.76 0 69 52

6 1 0 66 47

7 0 0.2 115 84

8 0 0.4 98 70

9 0 0.6 89 63

10 0 0.8 82 57

11 0 1 79 57

12 0.066 0.066 125 89

13 0.175 0.175 93 72

14 0.284 0.284 83 61

15 0.392 0.392 75 55

16 0.5 0.5 70 53

*Tab of device attached to topside copper

LM1117/LM1117I

10091913

FIGURE 7. θJA vs. 1oz Copper Area for SOT-223

10091934

FIGURE 8. θJA vs. 2oz Copper Area for TO-252

10091912

FIGURE 9. Maximum Allowable Power Dissipation vs. Ambient Temperature for SOT-223

LM1117/LM1117I

10091936

FIGURE 10. Maximum Allowable Power Dissipation vs. Ambient Temperature for TO-252

10091914

FIGURE 11. Maximum Allowable Power Dissipation vs. 1oz Copper Area for SOT-223

10091935

FIGURE 12. Maximum Allowable Power Dissipation vs. 2oz Copper Area for TO-252

LM1117/LM1117I

10091941

FIGURE 13. Top View of the Thermal Test Pattern in Actual Scale

LM1117/LM1117I

10091942

FIGURE 14. Bottom View of the Thermal Test Pattern in Actual Scale

LM1117/LM1117I

Typical Application Circuits

10091930

Adjusting Output of Fixed Regulators

10091931

Regulator with Reference

10091929

1.25V to 10V Adjustable Regulator with Improved Ripple Rejection

10091927

5V Logic Regulator with Electronic Shutdown*

LM1117/LM1117I

10091932

Battery Backed-Up Regulated Supply

10091933

Low Dropout Negative Supply

LM1117/LM1117I

Physical Dimensions inches (millimeters) unless otherwise noted

3-Lead SOT-223

NS Package Number MP04A

3-Lead TO-220

NS Package Number T03B

LM1117/LM1117I

3-Lead TO-263

NS Package Number TS3B

LM1117/LM1117I

3-Lead TO-252

NS Package Number TD03B

8-Lead LLP

NS Package Number LDC08A

LM1117/LM1117I

Notes

Incorporated

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All

semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time

of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which

have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such

components to meet such requirements.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265