- 302 -
P600A THRU P600M
6.0 AMPS Silicon Rectifiers
Voltage Range
50 to 1000 Volts
Current
6.0 Amperes
F
eatures
a Plastic material used carries
Underwriters Laboratory Classification
94V-0
a High forward current capability
a
High surge current capability
a
High temperature soldering guaranteed:
260oC/10 seconds, 0.375”(9.5mm) lead
length, 5lbs. (2.3kg) tension
M
echanical Data
a Cases: Molded plastic
a Lead: Plated axial leads, solderable per
MIL-STD-750, Method 2026
a Polarity: Color band denotes cathode
end
a Mounting position: Any
a
Weight: 0.07 ounce, 2.1 grams
P-600
Dimensions in inches and (millimeters)
M
aximum Ratings and Electrical Characteristics
Rating at 25ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number Symbol
P600A
P600B
P600D
P600G
P600J
P600K
P600M
Unit
s
Maximum Recurrent Peak Reverse Voltage VRRM
50 100
200
400
600
800
1000
V
Maximum RMS Voltage VRMS
35 70 140
280
420
560
700
V
Maximum DC Blocking Voltage VDC
50 100
200
400
600
800
1000
V
Maximum Average Forward Rectified Current at
TA=60oC, 0.375”(9.5mm) Lead Length (Fig 1)
TL=60, 0.125”(3.1mm) Lead Length (Fig 2) I(AV)
6.0
22.0
A
Peak Forward Surge Current, 8.3 ms Single Half
Sine-wave Superimposed on Rated Load (JEDEC
method ) IFSM
400.0 A
1.0
Maximum Instantaneous Forward Voltage @6.0A
@100A VF 1.3 1.4
V
Maximum DC Reverse Current @ TA=25
at Rated DC Blocking Voltage @ TA=100 IR 5.0
1.0 uA
mA
Typical Junction Capacitance ( Note 1 ) Cj 150.0 pF
Typical Reverse Recovery Time ( Note 2 ) Trr 2.5 uS
Typical Thermal Resistance (Note 3)
RJA
RJL
20.0
4.0 /W
Operating Junction and Storage Temperature
Range TJ, TSTG
-50 to + 150
Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C.
2. Reverse Recovery Time Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
3. Thermal Resistance from Junction to Ambient and from Junction to Lead at 0.375” (9.5mm) Lead Length,
P.C.B. Mounted with 1.1 x 1.1” ( 30 x 30mm) Copper Pads
REV.1 Oct.-2003
- 303 -
RATINGS AND CHARACTERISTIC CURVES (P600A THRU P600M)
FIG.6- TYPICAL TRANSIENT THERMAL IMPEDANCE
TRANSIENT THERMAL IMPEDANCE, C/W
O
10.01 0.1 10 100
0.1
10.0
1
100
T, PULSE DURATION, sec.
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
AVERAGE FORWARD RECTIFIED CURRENT. (A)
020 40 60 80 100 120 140 180 200160
0
1.0
2.0
3.0
4.0
5.0
6.0
AMBIENT TEMPERATURE. ( C)
o
1.1 x 1.0" (30 x 30mm)
COPPER PADS
60 Hz RESISTIVE OR
INDUCTIVE LOAD GROUND PLANE
1.0 X 1.0"
(25.4 X 25.4mm)
COPPER
SURFACE AREA
STANDARD P.C.B.
MOUNTING
0.375" (9.5mm) LEAD LENGTH
0.050"(1.27mm) min.
ALTERNATE
P.C.B. MOUNTING
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
AVERAGE FORWARD CURRENT. (A)
020 40 60 80 100 120 140 180 200160
0
5.0
10
15
20
25
30
LEAD TEMPERATURE. ( C)
o
60 Hz RESISTIVE OR
INDUCTIVE LOAD
L=0.125" (3.18mm)
L=0.25"
(6.35mm)
L=0.375"
(9.5mm)
L=0.625" (15.8mm)
BOTH LEADS
ATTACHED OF HEAT
SINKS WITH
LENGTH as
SHOWN, L
FIG.5- MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
PEAK FORWARD SURGE CURRENT AMPERES
0.1 1.0 10
0
100
200
300
400
500
600
NUMBER OF CYCLES AT 60 Hz
8.3 SINGLE HALF SINE-WAVE
(JEDEC METHOD)
T =25 C
AO
T =150 CAO
FIG.4- TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
INSTANTANEOUS FORDWARD CURRENT AMPERES
0.4 0.6 0.8 1.0 1.2 1.4 1.6
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
0.1
0.01
1
10
100
Tj=25 C
PULSE WIDTH-300 S
1% DUTY CYCLE
0
FIG.3- TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT MICROAMPERES
020 40 60 80 100 120 140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
0.1
0.01
1
10
100
Tj=125 C
0
Tj=25 C
0
Tj=100 C
0
