BI Technologies Corporation
4200 Bonita Place, Fullerton, CA 92835 USA
Phone: 714 447 2345 Website: www.bitechnologies.com
1/4” Square
Sealed Single Turn
Surface Mount
Cermet Trimming Potentiometer
Model 25
Seal 85°C Fluorinert® (No Leaks)
Temperature Coefficient ±100 ppm/°C
Operating Temperature Range –55°C to +125°C
Thermal Shock Five cycles –55°C to +125°C (2% ∆RT, 2% ∆VR)
Moisture Resistance Ten 24 hour cycles (3% ∆RT)
Shock 6 ms sawtooth, 100 G’s (1% ∆RT, 1% ∆VR)
Vibration 30 G’s, 10 to 2,000 Hz (1% ∆RT, 1% ∆VR)
High Temperature Exposure 250 hours at 125°C (2% ∆RT, 2% ∆VR)
Rotational Life 200 cycles (2 Ohms or 3% ∆RT, whichever is greater)
Load Life 1,000 hours at 70°C & 0.5 Watts (3% ∆RT, 3% ∆VR)
Resistance to Solder Heat 350°C for 3 sec. (1% ∆RT)
ENVIRONMENTAL
Standard Resistance Range 10 Ohms to 2 Megohms
Standard Resistance Tolerance ±10%
Input Voltage 300 Vdc Max. or rms not to exceed power rating
Power Rating 0.5 Watts at 70°C derating to 0 at 125°C
End Resistance 1% or 2 Ohms Max., whichever is greater
Actual Electrical Travel 210° nominal
Dielectric Strength 900 Vrms
Insulation Resistance 1,000 Megohms Min.
Resolution Essentially infinite
Contact Resistance Variation 1% or 3 Ohms Max., whichever is greater
ELECTRICAL
Specifications subject to change without notice.
Fluorinert® is a registered trademark of 3M Company.
Mechanical Stops Solid
Stop Strength 7 oz.-in. Min. (500 g-cm)
Torque 3 oz.-in. Max. (200 g-cm)
Weight 0.02 oz. nominal (0.6 grams)
MECHANICAL
May 25, 2011 Model 25 page 1 of 4
BI Technologies Corporation
4200 Bonita Place, Fullerton, CA 92835 USA
Phone: 714 447 2345 Website: www.bitechnologies.com
PACKAGING
ORDERING INFORMATION
Model Series
Pin Style
Resistance Prefix
Packaging Option for U or V
pin styles only:
AP = Ammo Pack
TR = Tape & Reel
Resistance Value
25 P R 10K LF TR
Optional RoHS compliant
product code
CIRCUIT DIAGRAM
(1)
(2)
(3)
CW
Model 25
May 25, 2011 Model 23 page 2 of 4
Pin Style V U
Tape Width = 18 mm 18 mm
Single hole sprocket = 0.50” pitch 0.50” pitch
Capacity = 1,000 units 750 units
Reel Diameter = 14” (363 mm) 14” (363 mm)
Option (TR code, only for U or V pin style): Tape & Reel. All units oriented with #3 pin toward direction of feed.
Standard (no code): Tubes. 50 units each. All units oriented wth #1 pin to same side.
STANDARD RESISTANCE VALUES
10 100 1K 10K 100K 1Meg
20 200 2K 20K 200K 2Meg
50 500 5K 50K 500K
Option (AP code, only for U or V pin style): Ammo pack. Tape fold 12”. Box 2.0” x 13.4” x 13.8” (50 mm x 340 mm x 350 mm)
