w w w 4U . m o c t e e h S a at .D TM240128CDG w w w .D e h t e U 4 .c m o t a S a w w w h .D a S a t t e e 4U . m o c ! " # Dark Blue Gray ! Transmissive/Positive $% &' ( )) *"+ #, # ( --./ 0- (1(, 2 , 13 ! )44445*) ! 4)44445() )3 ! 6 2 & 7 + 7 $)8, )$8)$9!!: )$*8)$*9!!: $ ,* - ; ! "" &' # ( )* +'# '! ! D G GTRANSMISSIVE DGRAY POSITIVE , ' -# ! .#' +/!'! Item Power Supply Voltage Symbol V V Min. Max. -0.3 6.0 Unit Remark V LCD Driving Voltage V Operating Temperature Range T Storage Temperature Range T - 25.0 0 +50 -20 +60 No Condensation 0# # ' 6.1 Electrical characteristics Item Symbol Min. Typ. Max. Unit Supply Voltage (Logic) V V 4.75 5.0 5.25 V Supply Voltage (LCD Drive) V - 18.5 - V 0.8V - V+0.3 V 0 - 0.2V V - 9.0 - mA Input Signal Voltage High Low Supply current (Logic) V V=5.0 V V=5.0 I (V- V=5.0V) Supply current (LCD Drive) I - 4.6 - mA Supply current (CCFL) I - 5.0 - mA " ( * $, -, " 0 -, 0 !1 % #' 20 -, 2 1 % #' 3 4 -, 5 4 -, 6 4 -, 4( -, ( 4* -, * 4" -, " ( 4 -, * 43 -, 3 " $1 -, $71 % #' 0 8 -, 0 % 9 #' 3 : # $%)' 5 ; -, $ 6 < -, < $ )) ) ! # !$%&' )* + $%)'% ' ! %-. /. ' $<-+8 = # $$<4 >7 5 ) $ ) ) $< $$<4 >7 ! = $ #3 + 3 +'= #$ #$ )) )) )) )) )) )) )) )) )) )) )) )) $ $ !$ %!*$ #($ % #!($ )) )) )) )) )) )) )) )) )) )) )) )) &# + ,*#- ,*#- %, &' % , &' %, &' .! )) )) )) )) )) )) )) )) )) )) )) )) )) )) )) )) )#' /)#' 0)#' 1)#' 2)#' 3)#' 4)#' 5)#' !!!. !6" )) )) )) )) )) )) !" ! )) )) )) )) )) )) )) )) )) 8 )) )) ' - ' &+ " ( !( !!!6" ! %$! %! &'$! &'! " " " '$! '$! '$! '$! 7 *#! 7 *#! )) )) * )) )) * )) )) * :9; )) )) * )) )) */ 9 6 )) )) *0 )) )) *1 )) )) *2 )) )) *3 )) )) *4:(9; +-3 # :75. ,,; 1 # 7.1 Optical Characteristics Item Symbol Ta=25 Condition Response Time Turn on Turn off Typ. -- Max. C Deg -30 =0 =0 =0 T -- 30 3.0 - - - - 300 =0 T Unit 20 C2 Contrast Ratio -30 =0 Viewing Angle Min. =0 ms - - 300 7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Bottom 7.2.2 Definition of Contrast Ratio Top Bottom Measuring Conditions: 1) Ambient Temperature: 25 7.2.3 Definition of Response time ; 2) Frame frequency: 64Hz Turn on time: = + Turn off time: = + Measuring Condition: 1) Operating Voltage: 18.5V ; 2) Frame frequency: 64Hz 2## 8.1 Content of Reliability Test No. Test Item 1 High Temperature Storage Low Temperature 2 Storage 3 4 5 6 Content of Test Endurance test applying the high storage temperature for a long time Endurance test applying the low storage temperature for a long time Endurance test applying the High Temperature electric stress (voltage current) Operation and the thermal stress to the element for a long time Endurance test applying the Low Temperature electric stress under low Operation temperature for a long time Endurance test applying the high High Temperature temperature and high humidity /Humidity Storage storage for a long time Endurance test applying the low and high temperature cycle Temperature 25 60 25 -20 Cycle 30min 5min 30min 5min 1 cycle 7 Vibration Test (package state) Endurance test applying the vibration during transportation 8 Shock Test (package state) Endurance test applying the shock during transportation 9 Atmospheric Pressure Test Endurance test applying the atmospheric pressure during transportation by air Ta=25 Test condition 60 96H -20 96H 50 96H 0 96H 40 90%RH 96H -20 /60 10 cycles 10Hz~150Hz, 50m/s, 40min Half- sine wave, 100m/s, 11ms 40kPa 16H 8.2 Failure Judgment Criterion Criterion Item Test Item No. 1 2 3 4 5 6 7 8 9 Failure Judgement Criterion Basic Specification Out of the basic Specification Electrical Specification Mechanical Specification Optical Characteristic Note Remark Out of the electrical specification Out of the mechanical specification Out of the optical specification For test item refer to 8.1 Basic specification = Optical specification + Mechanical specification 345*67** Examination At T=25 or Test (unless otherwise stated) Inspection Min. Max. Unit IL AQL Under normal Major External illumination and eyesight 1.0 Visual condition, the distance See Appendix A II Minor Inspection between eyes and LCD is 2.5 25cm. Under normal Major Display illumination and eyesight 1.0 See Appendix B II Defects condition, display on Minor inspection. 2.5 Note: Major defects: Open segment or common, Short, Serious damages, Leakage Miner defects: Others Sampling standard conforms to GB2828 $8' 5* +'# 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: 40 Temperature : 0 Relatively humidity: 80% 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. / Inspection items and criteria for appearance defects Items Contents Criteria Leakage Not permitted Rainbow According to the limit specimen Polarizer Black spot (in viewing area) Wrong polarizer attachment Not permitted Bubble between polarizer and glass Not counted Scratches of polarizer According to the limit specimen <0.3mm Max. 3 defects allowed 0.3mm 0.5mm Not counted Max. 3 spots allowed X<0.2mm 0.2mm X 0.5mm X=(a+b)/2 Black line (in viewing area) Not counted Max. 3 lines allowed a<0.02mm 0.02mm a 0.05mm b 2.0mm Progressive cracks Not permitted Max. 3 spots (lines) allowed /Inspection items and criteria for display defects Items Contents Criteria Open segment or open common Not permitted Short Not permitted Wrong viewing angle Not permitted Contrast radio uneven According to the limit specimen Crosstalk According to the limit specimen Not counted Max.3 dots allowed X<0.1mm 0.1mm X 0.2mm X=(a+b)/2 Pin holes and cracks in segment (DOT) Black spot (in viewing area) Not counted Max.2 dots allowed A<0.1mm 0.1mm A 0.2mm D<0.25mm Not counted Max.3 spots allowed X<0.1mm 0.1mm X 0.2mm X=(a+b)/2 Black line (in viewing area) Not counted Max.3 lines allowed a<0.02mm 0.02mm a 0.05mm b 0.5mm Max.3 dots allowed Max.3 spots (lines) allowed /Inspection items and criteria for display defects (continued) Items Content Criteria Not counted Max. 2 defects allowed x 0.1mm 0.1mm x 0.2mm x=(a+b)/2 Transformation of segment Not counted Max. 1 defects allowed a 0.1mm 0.1mm a 0.2mm D>0 Max.2 defects allowed 0.8W a 1.2W a=measured value of width W=nominal value of width Max.3 defects allowed